A novel face recognition method based on hypersausage neural networks

In this paper, we firstly give the nature of 'hypersausages', study its structure and training of the network, then discuss the nature of it by way of experimenting with ORL face database, and finally, verify its unsurpassable advantages compared with other means.

Large g factors of higher-lying excitons detected with reflectance difference spectroscopy in GaAs-based quantum wells

Exciton g factors in GaAs-based quantum wells (QWs) were evaluated by reflectance difference spectroscopy (RDS) under a weak magnetic field. The well-width dependence of the n=1 heavy-hole exciton (1H1E) g factor agrees well with the reported results, demonstrating RDS as a sensitive tool for detection of g factor. By comparison, the n=1 light-hole exciton g factor increases with the well width, and shows a larger value than that of 1H1E. In a 20-nm-wide Al0.02Ga0.98As/AlAs multiple QW sample, the g factors of up to ten excitons are obtained, and the higher-lying exciton g factors are found to be one order larger than that of the 1H1E exciton.

A high-performance Si-based MOS electrooptic phase modulator with a shunt-capacitor configuration

A novel Si-based metal-oxide-semiconductor (MOS) electrooptic phase modulator including two shunt oxide layer capacitors integrated on a silicon-on-insulator (SOI) waveguide is simulated and analyzed. The refractive index near the two gate oxide layers is modified by the free carrier dispersion effect induced by applying a positive bias on the electrodes. The theoretical calculation of free carrier distribution coupled with optical guided mode propagation characteristics has been carried out. The influence of the structure parameters such as the width and the doping level of the active region are analyzed. A half-wave voltage V-pi = 4 V is demonstrated with an 8-mm active region length and a 4-mu m width of an inner rib under an accumulation mode. When decreasing the inner rib width to 1 mu m, the phase modulation efficiency is even higher, and the rise and fall times reach 50 and 40 ps, respectively, with a 1.0 x 10(17) cm(-3) doping level in the active region.

Simulation and fabrication of thermo-optic variable optical attenuators based on multimode interference coupler

A type of thermo-optic variable optical attenuator based on multimode interference coupler is proposed. The optical field propagation properties of the devices are simulated using finite difference beam propagation method. The propagation loss of the fabricated device is 2-4.2 dB at the wavelength range 1510-1610 nm. The total power consumption is 370 mW and the maximum attenuation is more than 25 dB, which almost can meet the requirements of optical fiber communication systems.

H+ISFET-based biosensor for determination of penicillin G

A biosensor based on an H+ ion sensitive field effect transistor (H+-ISFET) and penicillin G acylase has been developed. The response time of the sensor to different concentrations of penicillin G was 30 s. In a 20 mM phosphate buffer at pH 7.0, the linear range of the calibration curve was from 0.5 to 8 mM. The coefficients of variation for three samples with 20 repeated measurements were below 5%. Stability of the sensor could reach about 6 months and more than 1000 runs were performed without a significant decrease of the output value. The sensor was tested for measurement of the penicillin G content in penicillin fermentation broth. Forty samples with low and high concentrations of penicillin G were chosen for the correlation test. The values assayed by the sensor method were compared with the values assayed by HPLC method, the correlation coefficient (r) was 0.9944 and the regression equation was y = 1.034X - 2083.7 respectively. The different measuring methods are discussed in the text. (C) 1998 Published by Elsevier Science S.A. All rights reserved.

Novel photonic crystal structure GaN-based light-emitting diodes - art. no. 68410J

For enhancing the output efficiency of GaN light-emitting diode(LED), we calculated the band structure of photonic crystal(PhC), and designed and fabricated several novel GaN LEDs with photonic crystal on Indium-Tin-Oxide(ITO), which as p-type transparent contact of GaN LED. In this fabricating process, we developed conventional techniques in order that these methods can be easily applied to industrial volume-production. And we have done some preliminary experiments and obtained some results.

Widely Frequency-Tunable Optical Microwave Source Based on Amplified Feedback Laser

A monolithic integrated amplified feedback semiconductor laser is demonstrated as an optical microwave source. The optical microwave frequency is continuously tunable in the range of 19.87-26.3 GHz with extinction ratio above 6 dB, 3-dB linewidth about 3MHz.

A Synthesis Tool for a Tile-Based Heterogeneous FPGA

A multi-mode logic cell architecture in a tile-based heterogeneous FPGA is proposed, and a logic synthesis tool, called Vsyn, based on this architecture is presented. The logic cell architecture design and its synthesis tool development are strongly influencing each other. Any feature or parameter from one needs to be fully exercised and verified on the other. In this paper, we presented experimental results based MCNC benchmarks to show that the integration of the synthesis tool and the FPGA architecture can achieve high performance in the targeted FPGA applications. In addition, Vsyn can also target embedded special-purpose macros for the heterogeneous FPGA.

Simulation and fabrication of the SiC-based clamped-clamped filter

In this paper, the SiC-based clamped-clamped filter was designed and fabricated. The filter was composed of two clamped-clamped beam micromechanical resonators coupled by a spring coupling beam. Structural geometries, including the length and width of the resonator beam and coupling beam, were optimized by simulation for high frequency and high Q, under the material properties of SiC. The vibrating modes for the designed filter structure were analyzed by finite element analysis (FEA) method. For the optimized structure, the geometries of resonator beams and coupling beams, as well as the coupling position, the SiC-based clamped-clamped filter was fabricated by surface micromaching technology.

Si based quantum cascade structure: from energy band structures design to materials growth

In this paper, we propose an n-type vertical transition bound-to-continuum Ge/SiGe quantum cascade structure utilizing electronic quantum wells in the L and Gamma valleys of the Ge layers. The optical transition levels are located in the quantum wells in the L valley. The Gamma-L intervalley scattering is used to depopulate the lower level and inject the electrons into the upper level. We also show that high quality Si1-yGey pseudosubstrate is obtained by thermal annealing of Si1-xGex/Ge/Si structure. (C) 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Research of Face Location System Based on Human Vision Simulations

In this paper we present a robust face location system based on human vision simulations to automatically locate faces in color static images. Our method is divided into four stages. In the first stage we use a gauss low-pass filter to remove the fine information of images, which is useless in the initial stage of human vision. During the second and the third stages, our technique approximately detects the image regions, which may contain faces. During the fourth stage, the existence of faces in the selected regions is verified. Having combined the advantages of Bottom-Up Feature Based Methods and Appearance-Based Methods, our algorithm performs well in various images, including those with highly complex backgrounds.

Vertical PIN ultraviolet photodetectors based on 4H-SiC homoepilayers

Vertical PIN ultraviolet photodetectors based on 4H-SiC homoepilayers are presented. The growth of the 4H-SiC homoepilayers was carried out in a LPCVD system. The size of the active area of the photodetector was 300 x 300 mu m(2). The dark and illuminated I-V characteristics were measured at reverse biases from 0 V to 30 V at room temperature. The illuminated current was at least two orders of magnitude higher than the dark current at a bias of below 12 V. The photoresponse was measured from 200 nm to 400 nm at different reverse biases and the peak values of the photo response were located at 3 10 nm. The calculated spectral detectivity D* was shown to be higher than 10(13) cmHz(1/2)/W from 260 to 360 nm with a peak value of 5.9 x 10(13) cmHz(1/2) /W at 310 nm. The peak value of the photoresponse was hundreds of times higher than the response at 400 nm, which showed the device had good visible blind performance. (c) 2007 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

VCSEL-based parallel optical transmission module

This paper describes the design process and performance of the optimized parallel optical transmission module. Based on 1x12 VCSEL (Vertical Cavity Surface Emitting Laser) array, we designed and fabricated the high speed parallel optical modules. Our parallel optical module contains a 1x12 VCSEL array, a 12 channel CMOS laser driver circuit, a high speed PCB (Printed Circuit Board), a MT fiber connector and a packaging housing. The L-I-V characteristics of the 850nm VCSEL was measured at the operating current 8mA, 3dB frequency bandwidth more than 3GHz and the optical output 1mW. The transmission rate of all 12 channels is 30Gbit/s, with a single channel 2.5Gbit/s. By adopting the integration of the 1x12 VCSEL array and the driver array, we make a high speed PCB (Printed Circuit Board) to provide the optoelectronic chip with the operating voltage and high speed signals current. The LVDS (Low-Voltage Differential Signals) was set as the input signal to achieve better high frequency performance. The active coupling was adopted with a MT connector (8 degrees slant fiber array). We used the Small Form Factor Pluggable (SFP) packaging. With the edge connector, the module could be inserted into the system dispense with bonding process.

Reconfigurable Optical Add-Drop Multiplexer Based on Silicon Photonic Wire Waveguide

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-06-04T07:40:23Z No. of bitstreams: 1 Reconfigurable Optical Add-Drop Multiplexer Based on Silicon Photonic Wire Waveguide.pdf: 416355 bytes, checksum: 5b80992194ba9fa818a011244cec6363 (MD5)

Diffractive Grating Based Out-of-Plane Coupling between Silicon Nanowire and Optical Fiber

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-06-04T07:55:26Z No. of bitstreams: 1 Diffractive Grating Based Out-of-Plane Coupling between Silicon Nanowire and Optical Fiber.pdf: 232805 bytes, checksum: 0bd17756b8a703bf8337dd25bbddaca3 (MD5)