An in vitro study of the radiobiological effects of flattening filter free radiotherapy treatments

Flattening filter free (FFF) linear accelerators allow for an increase in instantaneous dose-rate of the x-ray pulses by a factor of 2-6 over the conventional flattened output. As a result, radiobiological investigations are being carried out to determine the effect of these higher dose-rates on cell response. The studies reported thus far have presented conflicting results, highlighting the need for further investigation. To determine the radiobiological impact of the increased dose-rates from FFF exposures a Varian Truebeam medical linear accelerator was used to irradiate two human cancer cell lines in vitro, DU-145 prostate and H460 non-small cell lung, with both flattened and FFF 6 MV beams. The fluence profile of the FFF beam was modified using a custom-designed Nylon compensator to produce a similar dose profile to the flattened beam (6X) at the cell surface but at a higher instantaneous dose-rate. For both cell lines there appeared to be no significant change in cell survival. Curve fitting coefficients for DU145 cells irradiated with constant average dose-rates were 6X: alpha = 0.09 +/- 0.03, beta = 0.03 +/- 0.01 and 6FFF: alpha = 0.14 +/- 0.13, beta = 0.03 +/- 0.02 with a significance of p = 0.75. For H460 cells irradiated with the same instantaneous dose-rate but different average dose-rate the fit coefficients were 6FFF (low dose-rate): alpha = 0.21 +/- 0.11, 0.07 +/- 0.02 and 6FFF (high dose-rate): alpha = 0.21 +/- 0.16, 0.07 +/- 0.03, with p = 0.79. The results indicate that collective damage behaviour does not occur at the instantaneous dose-rates investigated here and that the use of either modality should result in the same clinical outcome, however this will require further validation in vivo.

The anatomy of Last Glacial Maximum climate variations in south Westland, New Zealand, derived from pollen records

We present pollen records from three sites in south Westland, New Zealand, that document past vegetation and inferred climate change between approximately 30,000 and 15,000 cal. yr BP. Detailed radiocarbon dating of the enclosing sediments at one of those sites, Galway tarn, provides a more robust chronology for the structure and timing of climate-induced vegetation change than has previously been possible in this region. The Kawakawa/Oruanui tephra, a key isochronous marker, affords a precise stratigraphic link across all three pollen records, while other tie points are provided by key pollen-stratigraphic changes which appear to be synchronous across all three sites. Collectively, the records show three episodes in which grassland, interpreted as indicating mostly cold subalpine to alpine conditions, was prevalent in lowland south Westland, separated by phases dominated by subalpine shrubs and montane-lowland trees, indicating milder interstadial conditions. Dating, expressed as a Bayesian-estimated single 'best' age followed in parentheses by younger/older bounds of the 95% confidence modelled age range, indicates that a cold stadial episode, whose onset was marked by replacement of woodland by grassland, occurred between 28,730 (29,390-28,500) and 25,470 (26,090-25,270) cal. yr BP (years before AD, 1950), prior to the deposition of the Kawakawa/Oruanui tephra. Milder interstadial conditions prevailed between 25,470 (26,090-25,270) and 24,400 (24,840-24,120) cal. yr BP and between 22,630 (22,930-22,340) and 21,980 (22,210-21,580) cal. yr BP, separated by a return to cold stadial conditions between 24,400 and 22,630 cal. yr BP. A final episode of grass-dominated vegetation, indicating cold stadial conditions, occurred from 21,980 (22,210-21,580) to 18,490 (18,670-17,950) cal. yr BP. The decline in grass pollen, indicating progressive climate amelioration, was well advanced by 17,370 (17,730-17,110) cal. yr BP, indicating that the onset of the termination in south Westland occurred sometime between ca 18,490 and ca 17,370 cal. yr BP. A similar general pattern of stadials and interstadials is seen, to varying degrees of resolution but generally with lesser chronological control, in many other paleoclimate proxy records from the New Zealand region. This highly resolved chronology of vegetation changes from southwestern New Zealand contributes to the examination of past climate variations in the southwest Pacific region. The stadial and interstadial episodes defined by south Westland pollen records represent notable climate variability during the latter part of the Last Glaciation. Similar climatic patterns recorded farther afield, for example from Antarctica and the Southern Ocean, imply that climate variations during the latter part of the Last Glaciation and the transition to the Holocene interglacial were inter-regionally extensive in the Southern Hemisphere and thus important to understand in detail and to place into a global context. © 2013 Elsevier Ltd. All rights reserved.

Impact of Wind Generation Mix on Transient Stability for an Interconnected Power System

The rapid growth of wind generation in many European countries is pushing power systems into
uncharted territory. As additional wind generators are installed, the changing generation mix may
impact on power system stability. This paper adopts the New England 39 bus system as a test
system for transient stability analysis. Thermal generator models are based on a likely future plant
mix for existing systems, while varying capacities of fixed-speed induction generators (FSIG) and
doubly-fed induction generators (DFIG) are considered. The main emphasis here has been placed
on the impact of wind technology mix on inter-area oscillations following transient grid
disturbances. In addition, both rotor angle stability and transient voltage stability are examined, and
results are compared with current grid code requirements and standards. Results have shown that
FSIGs can reduce tie-line oscillations and improve damping following a transient disturbance, but
they also cause voltage stability and rotor angle stability problems at high wind penetrations. In
contrast, DFIGs can improve both voltage and rotor angle stability, but their power output
noticeably oscillates during disturbances.

Truth Recovery and Transitional Justice: Deferring human rights issues

This book investigates why some societies defer the solution of transitional justice issues, such as the disappeared/missing, even after successful democratic consolidation. It also explains why the same societies finally decide to deal with these human rights issues. In short, it considers the interesting and understudied phenomenon of post-transitional justice. The prolonged silences in Spain, Cyprus and Greece contradict the experience of other countries -- such as South Africa, Bosnia, and Guatemala -- where truth recovery for disappeared/missing persons was a central element of the transition to peace and democracy. Despite democratization, the exhumation of mass graves containing the victims from the violence in Cyprus (1963-1974) and the Spanish civil war (1936-1939) was delayed until the early 2000s, when both countries suddenly decided to revisit the past. Cyprus and Spain are not alone: this is an increasing trend among countries trying to come to terms with past violence. Interestingly, despite similar background conditions, Greece is resisting the trend, challenging both theory and regional experience. Truth Recovery and Transitional Justice considers three interrelated issues. First, what factors can explain prolonged silence on the issue of missing persons in some transitional settings? Second, which processes can address the occasional yet puzzling transformation of victims’ groups from opponents of truth recovery to vocal pro-reconciliation pressure groups? Third, under which conditions is it better to tie victims’ rights to an overall political settlement? The book looks at Spain and Cyprus to show how they have attempted to bring closure to deep trauma by exhuming and identifying their missing, albeit under considerably different conditions. It then probes the generalizability of the conclusions on Spain and Cyprus by looking at the Greek experience; oddly, despite similar background conditions, Greece remains resistant to post-transitional justice norms. Interestingly, each case study takes a different approach to transitional justice.

Anniversaries

The hundredth anniversary of the outbreak of the First World War is only the first of a large number of major European historical anniversaries that will occur in the coming four years. Other twentieth-century anniversaries include that of the Russian Revolution and the Easter Uprising; notable corollaries from earlier centuries include the Battle of Bannockburn, the Hanoverian succession, the Battle of Waterloo and, perhaps most significant of all, the five hundredth anniversary of the Lutheran Reformation. Rather than commission special issues or other features to tie in to individual anniversaries centred on or relevant to German history in a manner which repeats unthinkingly the conventions of scholarly and popular culture, the editors elected to reflect more fundamentally on what might be at stake in major anniversaries for professional scholars of history. In anticipation of the major wave of scholarly and popular publications, commemorative activities and memory conflicts that each of these will generate, and in order to reflect upon the dynamics of German history, memory and commemoration in a more overtly comparative context, the editors invited a number of scholars working on different national histories to reflect on the possibilities and potential pitfalls such anniversaries offer to historians who tie their work in to such moments. They are Jörg Arnold (Nottingham), Thomas A. Brady (Berkeley), Fearghal McGarry (Queen’s University, Belfast), Tim Grady (Chester) and Dan Healey (St Antony’s College, Oxford). The questions were posed by the editors.

Flexural behaviour of external R/C steel fibre reinforced beam-column joints

A softened strut-and-tie macro model able to reproduce the flexural behaviour of
external beam-column joint is presented. The model is specific for concrete with hooked steel fibres (FRC) and it is designed to calculate the flexural response, as load-deflection curve, of a beam-column sub-assemblages. The model considers the presence of a constant vertical load acting on the column and of a monotonically increasing lateral force applied at the tip of the beam.

Comportamento flessionale di nodi esterni in calcestruzzo fibrorinforzato

SOMMARIO – Si presenta un macro modello di tipo reticolare in grado di riprodurre il comportamento in presenza di taglio e momento di nodi esterni trave-colonna di telai in calcestruzzo fibrorinforzato con fibre di acciaio
uncinato ed ordinario. Il caricamento del sistema è di tipo monotono come nel caso dell’analisi di pushover. Il modello considera la presenza di armature orizzontali e verticali della regione nodale e tiene in conto delle modalità
di rottura legate allo snervamento delle barre e allo schiacciamento delle regioni compresse in regime di sforzi pluriassiali. Il modello include le deformazioni flessionali della trave e della colonna in presenza di sforzo normale costante e restituisce la risposta del sistema colonna-nodo-trave (sub-assembralggio) tramite le curve carico-freccia all’estremità della semitrave. Per i singoli costituenti (trave, colonna e nodo) si è considerata la prima fessurazione, lo snervamento e lo schiacciamento delle regioni compresse e si sono fornite precise indicazioni sulla sequenza degli eventi che come è noto sono di fondamentale importanza per lo sviluppo di un progetto plastico che rispetti la gerarchia delle resistenze. Con l’uso del modello il controllo della gerarchia delle resistenze avviene a livello sezionale (lo snervamento delle barre deve avvenire prima dello schiacciamento delle regioni compresse) o di macro elemento (nella regione nodale lo snervamento delle staffe precede la crisi dei puntoni) e dell’intero elemento
sub-assemblaggio trave debole, colonna forte e nodo sovraresistente.
La risposta ottenuta con i modello proposto è in buon accordo con le risposte sperimentali disponibili in letteratura (almeno in termini di resistenza del sub-assemblaggio). Il modello è stato ulteriormente validato con analisi
numeriche agli elementi finiti condotte con il codice ATENA-2D. Le analisi numeriche sono state condotte utilizzando per il calcestruzzo fibroso adeguate leggi costitutive proposte dagli autori ed in grado di cogliere gli effetti
di softening e di resistenza residua a trazione legati alla presenza di fibre. Ulteriori sviluppi del modello saranno indirizzati a includere gli effetti di sfilamento delle barre d’armatura della trave e del conseguente degrado delle
tensioni d’aderenza per effetto di carichi monotonici e ciclici.

SUMMARY – A softened strut-and-tie macro model able to reproduce the flexural behavior of external beam-tocolumn joints with the presence of horizontal and vertical steel bars, including softening of compressed struts and yielding of main and secondary steel bars, is presented, to be used for the pushover analysis. The model proposed is able to calculate also the flexural response of fibrous reinforced concrete (FRC) beam-to-column sub-assemblages in term of a multilinear load-deflection curves. The model is able to take into account of the tensile behavior of main bars embedded in the surrounding concrete and of the softening of the compressed strut, the arrangement and percentage of the steel bars, the percentage and the geometry of steel fibers. First cracking, yielding of main steel and crushing of concrete were identified to determine the corresponding loads and displacement and to plot the simplified monotonic load-deflection curves of the sub-assemblages subjected in the column to constant vertical
load and at the tip of the beam to monotonically increasing lateral force. Through these load-delfection curves the component (beam, joint and column) that first collapse can be recognized and the capacity design can be verified.
The experimental results available in the literature are compared with the results obtained through the proposed model. Further, a validation of the proposed model is numerically made by using a non linear finite element program (ATENA-2D) able to analyze the flexural behavior of sub-assemblages.

North Atlantic marine radiocarbon reservoir ages through Heinrich event H4: A new method for marine age model construction

Cooling and sinking of dense saline water in the Norwegian–Greenland Sea is essential for the formation of North Atlantic Deep Water. The convection in the Norwegian–Greenland Sea allows for a northward flow of warm surface water and southward transport of cold saline water. This circulation system is highly sensitive to climate change and has been shown to operate in different modes. In ice cores the last glacial period is characterized by millennial-scale Dansgaard–Oeschger (D–O) events of warm interstadials and cold stadials. Similar millennial-scale variability (linked to D–O events) is evident from oceanic cores, suggesting a strong coupling of the atmospheric and oceanic circulations system. Particularly long-lasting cold stadials correlate with North Atlantic Heinrich events, where icebergs released from the continents caused a spread of meltwater over the northern North Atlantic and Nordic seas. The meltwater layer is believed to have caused a stop or near-stop in the deep convection, leading to cold climate. The spreading of meltwater and changes in oceanic circulation have a large influence on the carbon exchange between atmosphere and the deep ocean and lead to profound changes in the 14C activity of the surface ocean. Here we demonstrate marine 14C reservoir ages (R) of up to c. 2000 years for Heinrich event H4. Our R estimates are based on a new method for age model construction using identified tephra layers and tie-points based on abrupt interstadial warmings.

Analysis of VSC-based HVDC System under DC Faults

This paper analyzes the behavior of a Voltage Source Converter Based HVDC system under DC cable fault conditions. The behavior of the HVDC system during a permanent line-to-earth fault is analyzed, outlining the systems configuration and behavior at each stage of the fault timeline. Operation of the proposed system under a single earthing configurations i.e. Converter (solid) earthed/AC transformer unearthed, was analyzed and simulated, with particular attention paid to the converters operation. It was observed that the development of potential earth loops within the system as a result of DC line- toearth faults leads to substantial overcurrent and results in system configuration oscillation.

The role of immune-related myeloid cells in angiogenesis

Macrophage function is not restricted to the innate and adaptive immune responses, but also includes host defence, wound healing, angiogenesis and homeostatic processes. Within the spectrum of macrophage activation there are two extremes: M1 classically activated macrophages which have a pro-inflammatory phenotype, and M2 alternatively activated macrophages which are pro-angiogenic and anti-inflammatory. An important property of macrophages is their plasticity to switch from one phenotype to the other and they can be defined in their polarisation state at any point between the two extremes. In order to determine what stage of activation macrophages are in, it is essential to profile various phenotypic markers for their identification. This review describes the angiogenic role for myeloid cells: circulating monocytes, Tie-2 expressing monocytes (TEMs), myeloid-derived suppressor cells (MDSCs), tumour associated macrophages (TAMs), and neutrophils. Each cell type is discussed by phenotype, roles within angiogenesis and possible targets as a cell therapy. In addition, we also refer to our own research on myeloid angiogenic cells (MACs), outlining their ability to induce angiogenesis and their similarities to alternatively activated M2 macrophages. MACs significantly contribute to vascular repair through paracrine mechanisms as they lack the capacity to differentiate into endothelial cells. Since MACs also retain plasticity, phenotypic changes can occur according to disease states and the surrounding microenvironment. This pro-angiogenic potential of MACs could be harnessed as a novel cellular therapy for the treatment of ischaemic diseases, such as diabetic retinopathy, hind limb ischaemia and myocardial infarction; however, caution needs to be taken when MACs are delivered into an inflammatory milieu.

New SR drive with integrated charging capacity for plug-in hybrid electric vehicles (PHEVs)

Plug-in hybrid electric vehicles (PHEVs) provide much promise in reducing greenhouse gas emissions and, thus, are a focal point of research and development. Existing on-board charging capacity is effective but requires the use of several power conversion devices and power converters, which reduce reliability and cost efficiency. This paper presents a novel three-phase switched reluctance (SR) motor drive with integrated charging functions (including internal combustion engine and grid charging). The electrical energy flow within the drivetrain is controlled by a power electronic converter with less power switching devices and magnetic devices. It allows the desired energy conversion between the engine generator, the battery, and the SR motor under different operation modes. Battery-charging techniques are developed to operate under both motor-driving mode and standstill-charging mode. During the magnetization mode, the machine's phase windings are energized by the dc-link voltage. The power converter and the machine phase windings are controlled with a three-phase relay to enable the use of the ac-dc rectifier. The power converter can work as a buck-boost-type or a buck-type dc-dc converter for charging the battery. Simulation results in MATLAB/Simulink and experiments on a 3-kW SR motor validate the effectiveness of the proposed technologies, which may have significant economic implications and improve the PHEVs' market acceptance

Evaluating environmental enrichment options for commercial broiler chickens

Implications Provision of environmental enrichment in line with that required by welfare-based quality assurance schemesdoes not always appear to lead to clear improvements in broiler chicken welfare. This research perhaps serves to highlightthe deficit in information regarding the ‘real world’ implications of enrichment with perches, string and straw bales.

Introduction Earlier work showed that provision of natural light and straw bales improved leg health in commercial broilerchickens (Bailie et al., 2013). This research aimed to determine if additional welfare benefits were shown in windowedhouses by increasing straw bale provision (Study 1), or by providing perches and string in addition to straw bales (Study 2).

Material and methods Commercial windowed houses in Northern Ireland containing ~23,000 broiler chickens (placed inhouses as hatched) were used in this research which took place in 2011. In Study 1 two houses on a single farm wereassigned to one of two treatments: (1) 30 straw bales per house (1 bale/44m2), or (2) 45 straw bales per house (1bale/29m2). Bales of wheat straw, each measuring 80cm x 40cm x 40cm were provided from day 10 of the rearing cycle,as in Bailie et al. (2013). Treatments were replicated over 6 production cycles (using 276,000 Ross 308 and Cobb birds),and were swapped between houses in each replicate. In Study 2, four houses on a single farm were assigned to 1 of 4treatments in a 2 x 2 factorial design. Treatments involved 2 levels of access to perches (present (24/house), or absent), and2 levels of access to string (present (24/house), or absent), and both types of enrichment were provided from the start of thecycle. Each perch consisted of a horizontal, wooden beam (300 cm x 5 cm x 5cm) with a rounded upper edge resting on 2supports (15 cm high). In the string treatment, 6 pieces of white nylon string (60 cm x 10 mm) were tied at their mid-pointto the wire above each of 4 feeder lines. Thirty straw bales were also provided per house from day 10. This study wasreplicated over 4 production cycles using 368,000 Ross 308 birds. In both studies behaviour was observed between 0900and 1800 hours in weeks 3-5 of the cycle. In Study 1, 8 focal birds were selected in each house each week, and generalactivity, exploratory and social behaviours recorded directly for 10 minutes. In Study 2, 10 minute video recordings weremade of 6 different areas (that did not contain enrichment) of each house each week. The percentage of birds engaged inlocomotion or standing was determined through scan sampling these recordings at 120 second intervals. Four perches andfour pieces of string were filmed for 25 mins in each house that contained these enrichments on one day per week. The totalnumber of times the perch or string was used was recorded, along with the duration of each bout. In both studies, gaitscores (0 (perfect) to 5 (unable to walk)) and latency to lie (measured in seconds from when a bird had been encouraged tostand) were recorded in 25 birds in each house each week. Farm and abattoir records were also used in both studies todetermine the number of birds culled for leg and other problems, mortality levels, slaughter weights, and levels of pododermatitis and hock burn. Data were analysed using SPSS (version 20.0) and treatment and age effects on behaviouralparameters were determined in normally distributed data using ANOVA (‘Straw bale density*week’, or‘string*perches*week’ as appropriate), and in non-normally distributed data using Kuskall-Wallace tests (P<0.05 forsignificance) . Treatment (but not age) effects on performance and health data were determined using the same testsdepending on normality of data.

Results Average slaughter weight, and levels of mortality, culling, hock burn and pododermatitis were not affected bytreatment in either study (P<0.05). In Study 1 straw bale (SB) density had no significant effect on the frequency orduration of behaviours including standing, walking, ground pecking, dust bathing, pecking at bales or aggression, or onaverage gait score (P>0.05). However, the average latency to lie was greater when fewer SB were provided (30SB 23.38s,45SB 18.62s, P<0.01). In Study 2 there was an interaction between perches (Pe) and age in lying behaviour, with higherpercentages of birds observed lying in the Pe treatment during weeks 4 and 5 (week 3 +Pe 77.0 -Pe 80.9, week 4 +Pe 79.5 -Pe 75.2, week 5 +Pe 78.4 -Pe 76.2, P<0.02). There was also a significant interaction between string (S) and age inlocomotory behaviour, with higher percentages of birds observed in locomotion in the string treatment during week 3 butnot weeks 4 and 5 (week 3 +S 4.9 -S 3.9, week 4 +S 3.3 -S 3.7, week 5 +S 2.6 -S 2.8, P<0.04). There was also aninteraction between S and age in average gait scores, with lower gait scores in the string treatment in weeks 3 and 5 (week3: +S 0.7, -S 0.9, week 4: +S 1.5, -S 1.4, week 5: +S 1.9, -S 2.0, P<0.05). On average per 25 min observation there were15.1 (±13.6) bouts of perching and 19.2 (±14.08) bouts of string pecking, lasting 117.4 (±92.7) and 4.2 (±2.0) s for perchesand string, respectively.

Conclusion Increasing straw bale levels from 1 bale/44m2 to 1 bale/29m2 floor space does not appear to lead to significantimprovements in the welfare of broilers in windowed houses. The frequent use of perches and string suggests that thesestimuli have the potential to improve welfare. Provision of string also appeared to positively influence walking ability.However, this effect was numerically small, was only shown in certain weeks and was not reflected in the latency to lie.Further research on optimum design and level of provision of enrichment items for broiler chickens is warranted. Thisshould include measures of overall levels of activity (both in the vicinity of, and away from, enrichment items).

Adaptive backstepping droop controller design for multi-terminal high-voltage direct current systems

Wind power is one of the most developed renewable energy resources worldwide. To integrate offshore wind farms to onshore grids, the high-voltage direct current (HVDC) transmission cables interfaced with voltage source converters (VSCs) are considered to be a better solution than conventional approaches. Proper DC voltage indicates successive power transfer. To connect more than one onshore grid, the DC voltage droop control is one of the most popular methods to share the control burden between different terminals. However, the challenges are that small droop gains will cause voltage deviations, while higher droop gain settings will cause large oscillations. This study aims to enhance the performance of the traditional droop controller by considering the DC cable dynamics. Based on the backstepping control concept, DC cables are modelled with a series of capacitors and inductors. The final droop control law is deduced step-by-step from the original remote side. At each step the control error from the previous step is considered. Simulation results show that both the voltage deviations and oscillations can be effectively reduced using the proposed method. Further, power sharing between different terminals can be effectively simplified such that it correlates linearly with the droop gains, thus enabling simple yet accurate system operation and control.

Split Converter-Fed SRM Drive for Flexible Charging in EV/HEV Applications

Electric vehicles (EVs) and hybrid EVs are the way forward for green transportation and for establishing low-carbon economy. This paper presents a split converter-fed four-phase switched reluctance motor (SRM) drive to realize flexible integrated charging functions (dc and ac sources). The machine is featured with a central-tapped winding node, eight stator slots, and six rotor poles (8/6). In the driving mode, the developed topology has the same characteristics as the traditional asymmetric bridge topology but better fault tolerance. The proposed system supports battery energy balance and on-board dc and ac charging. When connecting with an ac power grid, the proposed topology has a merit of the multilevel converter; the charging current control can be achieved by the improved hysteresis control. The energy flow between the two batteries is balanced by the hysteresis control based on their state-of-charge conditions. Simulation results in MATLAB/Simulink and experiments on a 150-W prototype SRM validate the effectiveness of the proposed technologies, which may provide a solution to EV charging issues associated with significant infrastructure requirements.

Evaluation of the ionic liquids 1-alkyl-3-methylimidazolium hexafluorophosphate as a solvent for the extraction of benzene from cyclohexane : ( Liquid + liquid ) equilibria

In the catalytic hydrogenation of benzene to cyclohexane, the separation of unreacted benzene from the product stream is inevitable and essential for an economically viable process. In order to evaluate the separation efficiency of ionic liquids (ILs) as a solvent in this extraction processes, the ternary (liquid + liquid) equilibrium of 1-alkyl-3-methylimidazolium hexafluorophosphate, [Cnmim][PF6] (n = 4, 5, 6), with benzene and cyclohexane was studied at T = 298.15 K and atmospheric pressure. The reliability of the experimentally determined tie-line data was confirmed by applying the Othmer–Tobias equation. The solute distribution coefficient and solvent selectivity for the systems studied were calculated and compared with literature data for other ILs and sulfolane. It turns out that the benzene distribution coefficient increases and solvent selectivity decreases as the length of the cation alkyl chain grows, and the ionic liquids [Cnmim][PF6] proved to be promising solvents for benzene–cyclohexane extractive separation. Finally, an NRTL model was applied to correlate and fit the experimental LLE data for the ternary systems studied.