Complex quantum ring structures formed by droplet epitaxy

Well-defined complex quantum ring structures formed by droplet epitaxy are demonstrated. By varying the temperature of the crystallizing Ga droplets and changing the As flux, GaAs/AlGaAs quantum single rings and concentric quantum double rings are fabricated, and double-ring complexes are observed. The growth mechanism of these quantum ring complexes is addressed. (c) 2006 American Institute of Physics.

A complex Fourier transformation study of the contactless electroreflectance of an undoped-n(+) GaAs structure

Complex Fourier transformation (CFT) has been employed to analyse contactless electroreflectance (CER) spectra from an undoped-n(+) GaAs structure with various ac modulations and dc bias voltages. The CFT spectra of CER have been compared with those of photoreflectance (PR). It has been found that the CER non-flat modulation is between the built-in electric field and a larger electric field which increases with the modulation voltage. The result has been explained by the screening of the applied modulation electric field in one of the two half modulation cycles and the trapping of electrons in surface states in the other half modulation cycle. The dc bias does not change the CER spectra, hence their CFT spectra. This is because of the screening of the applied dc bias electric field.

Epitaxial growth of SiC on complex substrates

Epitaxial growth of SiC on complex substrates was carried out at substrate temperature from 1200 degreesC to 1400 degreesC. Three kinds of new complex substrates, c-plane sapphire, AlN/sapphire, and GaN/AlN/sapphire, were used in this study. We obtained a growth rate in the range of 1-6 mum/h. Thick (6 mum) SIC epitaxial layers with no cracks were successfully obtained on AlN/sapphire and GaN/AlN/sapphire substrates. X-ray diffraction patterns have confirmed that single-crystal SiC was obtained on these complex substrates. Analysis of optical transmission spectra of the SIC grown on sapphire substrates shows the lowest-energy gap near 2.2 eV, which is the value for cubic SiC. The undoped SIC showed n-type electrical conductivity. (C) 2001 Elsevier Science B.V. All rights reserved.

Application of the compatibility relationship(1) in seeking a functional relationship among species' equilibrium quantities in complex systems

A new algorithm, representing an important advance in determination of the functional relationship, is first reported here. The algorithm is very useful and convenient for analyzing the incorporation of impurities. To show how the algorithm works, two early and well-known vapor phase epitaxy (VPE) experiments-Ashen's (Ashen, D. J.; Dean, P. J.; Hurle, D. T. J.; Mullin, J. B.; Royle, A.; White, A. M. Gallium Arsenide and Related Compounds, Institute of Physics Conference Series 24, 1974; Institute of Physics: London, 1975; p 229.), involving the doping of silicon and DiLorenzo's (DiLorenzo, J. V. J. Cryst. Growth 1972, 17, 189.), involving the mole fraction effect-are calculated to find the functional relationship between the Si contamination and the partial pressure of HCl. The calculated curves agree with the experimental results. A conclusion that the calculated values are greater than the true values has been drawn.

Compensation ratio-dependent concentration of a VInH4 complex in n-type liquid encapsulated Czochralski InP

The concentration of hydroen-indium vacancy complex VInH4 in liquid encapsulated Czochralski undoped and Fe-doped n-type InP has been studied by low-temperature infrared absorption spectroscopy. The VInH4 complex is found to be a dominant intrinsic shallow donor defect with concentrations up to similar to 10(16) cm(-3) in as-grown liquid encapsulated Czochralski InP. The concentration of the VInH4 complex is found to increase with the compensation ratio in good agreement with the proposed defect formation model of Walukiewicz [W. Walukiewicz, Phys. Rev. B 37, 4760 (1998); Appl. Phys. Lett. 54, 2094 (1989)], which predicts a Fermi-level-dependent concentration of amphoteric defects. (C) 1998 American Institute of Physics, [S0003-6951(98)04435-0].

A novel 1.3-mu m high T-0 AlGaInAs/InP strained-compensated multi-quantum well complex-coupled distributed feedback laser diode

A 1.3-mu m AlGaInAs/InP buried heterostructure (BH) stripe distributed feedback laser with a novel AlInAs/InP complex-coupled grating grown by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) is proposed and demonstrated. A high characteristic temperature (T-0 = 90K between 20-80 degrees C) and temperature-insensitive slope efficiency (0.25 dB drop from 20 to 80 degrees C) in 1.3 mu m AlGaInAs/InP DFB lasers was obtained by introducing AI(Ga)InAs graded-index separate-confinement heterostructure (GRINSCH) layers and a strained-compensated (SC) multi-quantum well (MQW).

A Complex BPF with On Chip Auto-tuning Architecture for Wireless Receivers

A 3(rd) order complex band-pass filter (BPF) with auto-tuning architecture is proposed in this paper. It is implemented in 0.18um standard CMOS technology. The complex filter is centered at 4.092MHz with bandwidth of 2.4MHz. The in-band 3(rd) order harmonic input intercept point (IIP3) is larger than 16.2dBm, with 50 Omega as the source impedance. The input referred noise is about 80uV(rms). The RC tuning is based on Binary Search Algorithm (BSA) with tuning accuracy of 3%. The chip area of the tuning system is 0.28 x 0.22 mm(2), less than 1/8 of that of the main-filter which is 0.92 x 0.59 mm(2). After tuning is completed, the tuning system will be turned off automatically to save power and to avoid interference. The complex filter consumes 2.6mA with a 1.8V power supply.

A Complex BPF with On Chip Auto-tuning Architecture for Low-IF Receivers

A 3(rd) order complex band-pass filter (BPF) with auto-tuning architecture is proposed in this paper. It is implemented in 0.18 mu m standard CMOS technology. The complex filter is centered at 4.092MHz with bandwidth of 2.4MHz. The in-band 3(rd) order harmonic input intercept point (IIP3) is larger than 19dBm, with 50 Omega as the source impedance. The input referred noise is about 80 mu V-rms. The RC tuning is based on Binary Search Algorithm (BSA) with tuning accuracy of 3%. The chip area of the tuning system is 0.28x0.22mm(2), less than 1/8 of that of the main-filter which is 0.92x0.59mm(2). After tuning is completed, the tuning system will be turned off automatically to save power and to avoid interference. The complex filter consumes 2.6mA with a 1.8V power supply.

Research of Face Detection System Applied for Detecting Faces with Complex Background and Illumination

An effective face detection system used for detecting multi pose frontal face in gray images is presented. Image preprocessing approaches are applied to reduce the influence of the complex illumination. Eye-analog pairing and improved multiple related template matching are used to glancing and accurate face detecting, respectively. To shorten the time cost of detecting process, we employ prejudge rules in checking candidate image segments before template matching. Test by our own face database with complicated illumination and background, the system has high calculation speed and illumination independency, and obtains good experimental results.

A more complex neuron in biomimetic pattern recognition

Biomimetic pattern recognition has been proposed for several years, but the discussion of its neuron was not very wide and deep. In this paper, we propose a new more complex neuron named M-neuron and give the application in the last part of the paper.

Complex networks constructed from irrational number sequences

In this paper, we construct (d, r) networks from sequences of different irrational numbers. In detail, segment an irrational number sequence of length M into groups of d digits which represent the nodes while two consecutive groups overlap by r digits (r = 0,1,...,d-1), and the undirected edges indicate the adjacency between two consecutive groups. (3, r) and (4, r) networks are respectively constructed from 14 different irrational numbers and their topological properties are examined. By observation, we find that network topologies change with different values of d, r and even sequence length M instead of the types of irrational numbers, although they share some similar features with traditional random graphs. We make a further investigation to explain these interesting phenomena and propose the identical-degree random graph model. The results presented in this paper provide some insight into distributions of irrational number digits that may help better understanding of the nature of irrational numbers.

Satellite Constellation Design for Complex Coverage

Most traditional satellite constellation design methods are associated with a simple zonal or global, continuous or discontinuous coverage connected with a visibility of points on the Earth's surface. A new geometric approach for more complex coverage of a geographic region is proposed. Full and partial coverage of regions is considered. It implies that, at any time, the region is completely or partially within the instantaneous access area of a satellite of the constellation. The key idea of the method is a two-dimensional space application for maps of the satellite constellation and coverage requirements. The space dimensions are right ascension of ascending node and argument of latitude. Visibility requirements of each region can be presented as a polygon and satellite constellation as a uniform moving grid. At any time, at least one grid vertex must belong to the polygon. The optimal configuration of the satellite constellation corresponds to the maximum sparse grid. The method is suitable for continuous and discontinuous coverage. In the last case, a vertex belonging to the polygon should be examined with a revisit time. Examples of continuous coverage for a space communication network and of the United States are considered. Examples of discontinuous coverage are also presented.

The design structure system - A method for managing the design of complex systems

Systems design involves the determination of interdependent variables. Thus the precedence ordering for the tasks of determining these variables involves circuits. Circuits require planning decisions abut how to iterate and where to use estimates. Conventional planning techniques, such as critical path, do not deal with these problems. Techniques are shown in this paper which acknowledge these circuits in the design of systems. These techniques can be used to develop an effective engineering plan, showing where estimates are to be used, how design iterations and reviews are handled, and how information flows during the design work.