A new synthetic procedure for the preparation of pyridinium tetrafluoroborate and hexafluorosilicate

Pyridinium tetrafluoroborate (C5H5NHBF4) and pyridinium hexafluorosilicate [(C5H5NH)2SiF6] have been prepared in good yields and high purity by the reaction of pyridinium poly(hydrogen fluoride) with oxides and acids of boron and silicon respectively. The salts have been characterised by melting points, IR, 1H and 19F NMR spectroscopy and chemical analysis.

An elegant direct route for the preparation of pyridinium, ammonium and alkali metal hexafluorotitanates (IV)

Pyridinium hexafluorotitanate (IV) has been prepared by a one step procedure. Addition of titanium tetrachloride to pyridinium poly(hydrogen fluoride) yields nearly quantitative amounts of pyridinium hexafluorotitanate(IV). Making use of pyridinium hexafluorotitanate as precursor, ammonium and alkali metal (Na, K, Rb, and Cs) hexafluorotitanates have been prepared in good yields. These salts have been characterised by IR, N.M.R. (1H, 13C and 19F), X-ray powder diffraction data and chemical analysis.

An Electron-Microscopic Investigation Of Oxides Related To Beta-Alumina

High resolution electron microscopic (HREM) investigation of potassiumbeta-alumina and the related gallate and ferrite has revealed that whereas the aluminate and gallate are highly disordered, consisting of random sequence ofbeta andbetaPrime units, the ferrite is more ordered. The aluminate and gallate are sensitive to electron beam irradiation exhibiting beam-induced damage similar to sodiumbetaPrime-alumina. Significantly, the ferrite is beamstable, the difference in behaviour amongst these related oxides arising from the different mechanisms by which alkali metal nonstoichiometry is accommodated. Barium hexaaluminate and hexaferrite are both highly ordered; specimens prepared by the barium borate flux method exhibit a new radic3a×radic3a superstructure of the hexagonal magnetoplumbite cell.

Preventive orientation and caries management by Iranian dentists

Ehkäisypainotteisuus karieksen hoidossa: iranilaishammaslääkärien hoitovalinnat Karies aiheuttaa hampaiden kovan pinnan ja hammasluun syöpymistä, joka lopulta näkyy ”reikänä”. Iästä riippumatta kariesvaara vaanii kaikkia hampaiden omistajia, vauvasta vaariin, ja lähes kaikilla aikuisilla on suussaan merkkejä karieksesta. Karies etenee yleensä hitaasti ja antaa siten aikaa ehkäisevälle hoidolle. Tämä etsikkoaika jää usein käyttämättä, ja karieksen hoito painottuu reikien paikkaamiseen. Karies voitaisiin pitää kurissa sen ehkäisyyn kehitetyillä monipuolisilla keinoilla. Hammaslääkärit ovat avainasemassa, sillä he tekevät kauaskantoisia valintoja — hoidetaanko kariesta paikkaamalla vai valitaanko ehkäisevä hoito? Valintojen taustalla ovat hammaslääkärin tietotaso, asenteet ja omat terveystavat sekä potilaiden ja vastaanoton aiheuttamiksi koetut esteet. Tämä kyselytutkimus selvitti karieksen hoitovalintoja ja niiden taustoja Iranissa. Kysymyslomakkeet jaettiin kahdessa hammaslääkärien kongressissa Teheranissa (2004─2005) ja palautettiin nimettöminä. Kysely kartoitti hammaslääkärien tietoja karieksen ehkäisykeinoista ja asenteita ehkäisyä kohtaan sekä koettuja esteitä sen toteuttamisessa. Hoitovalintoja selvitettiin tarkasti kuvattujen esimerkkipotilaiden avulla. Kysely kartoitti myös hammaslääkärien omat terveystavat: suun omahoidon, tupakoinnin ja hammaslääkärissä käynnin. Aineisto käsitti 980 iältään keskimäärin 37-vuotiasta hammaslääkäriä, joista 64 % oli miehiä. Iranilaishammaslääkärien tiedot karieksen ehkäisystä olivat fluorihammastahnan merkitystä lukuun ottamatta hyvät ja heidän asenteensa ehkäisyä kohtaan valtaosin myönteiset. Tästä huolimatta 77 % heistä olisi valinnut suuren kariesvaaran potilaalle hammaskiilteessä olevan reiän hoidoksi paikkauksen. Ehkäisyhoidoksi tarjotuista 8:sta keinosta lähes kaikki hammaslääkärit valitsivat suuren kariesvaaran potilaalle hoidoksi harjausopetuksen ja säännölliset hammastarkastukset, noin 80 % valitsi hampaiden puhdistamisen vastaanotolla ja ravintoneuvonnan, 70 % ohjeet fluorihuuhteluista kotona ja 53 % vastaanotolla tehtävän fluorikäsittelyn. Potilaiden vastustavat mielipiteet arvioitiin suurimmaksi esteeksi ehkäisevän hoidon toteuttamiselle. Hammaslääkäreistä 59 % ilmoitti harjaavansa hampaansa kahdesti päivässä; 76 % ei tupakoinut ja 56 % kertoi aina ehdottavansa tupakoivalle potilaalle tupakoinnin lopettamista. Hammaslääkärien ehkäisypainotteisuus karieshoidossa oli naisilla vahvempi kuin miehillä. Tulosten perusteella voi päätellä, että Iranissa tulisi nykyistä selvemmin suosia ehkäisevää linjaa karieksen hoitovalintoja tehtäessä ja hammaslääkäreitä koulutettaessa. Potilastyössä koettujen ehkäisyhoidon esteiden syvällisempi ymmärtäminen edesauttaisi niiden poistamisessa.

Oral health behaviour, conditions and care among dentate elderly patients in Lithuania: preventive aspects

The present cross-sectional study aimed to assess oral health behaviour, dental and periodontal conditions, dental care, and their relationships among elderly dentate patients in Lithuania. The target population in the study were dentate patients aged 60 and older attending public dental services in Kedainiai, Lithuania. The data collection took place between the autumn of 1999 and the winter of 2001. Data were collected by means of a self-administered questionnaire for all (n=174) and a clinical examination targeting about half of the subjects (n=100). The questionnaire inquired about oral health behaviour, the life-first and also the most recent dental treatments, sources on and self-assessed knowledge of oral self-care, a self-reported number of teeth, and socio-demographic information. The clinical examination included basic dental and periodontal conditions. A total of 82 women and 92 men completed the questionnaire; their mean age was 69.2 and their average number of teeth was 16.2 (CI 95% 15.4-17.1). In all, 25% had 21 or more teeth and 32% indicated wearing removable dentures. The oral health behaviour, the participants reported, was poor: 30% reported twice daily toothbrushing, 57% responded that they always use fluoride toothpaste, 19% indicated daily interdental cleaning, nearly all said they take sugar in their coffee and tea, and 30% indicated going for check-ups. As the main source of information on oral self-care, the subjects indicated health professionals (82%), followed by social contacts (72%), broadcasted media (58%), and printed media (42%). A total of 34% assessed their knowledge of oral self-care as good, and their self-assessed knowledge correlated (r=0.52) with professional guidance they had received about oral self-care. In their most recent treatment, conservative (39%) and non-conservative (34%) treatments dominated, and preventive ones were the least reported (7%). Regarding guidance in oral self-care, 54% reported having received such about toothbrushing, 32% about interdental cleaning, and 33% had been given visual information. Clinical examinations revealed the presence of plaque, calculus, bleeding on probing and deepened pockets in all of the subjects; 70% of the subjects were diagnosed with pockets of 6mm and deeper, 94% with caries, and 73% with overhangs of restorations. Those subjects assessing their knowledge of oral self-care as good and reporting a higher intensity of guidance in oral self-care as received, indicated practicing the recommended oral self-care more frequently. Twice daily toothbrushing was associated with good self-assessed knowledge of oral self-care (OR 4.1, p<0.001) and a university education (OR 5.6, p<0.001). Those subjects with better oral health behaviour had a greater number of teeth. Having 21 or more teeth was associated with good self-assessed knowledge of oral self-care (OR 4.1, p=0.03). Better periodontal conditions were associated with a higher frequency of toothbrushing. The presence of periodontal pockets of 6mm and deeper was associated with the level of self-assessed knowledge of oral self-care being below good (OR=3.0, p=0.04) and the level of dental cleanliness being poor (OR=2.7, p=0.02). To conclude, oral health behaviour and conditions call for improvement in elderly subjects in Lithuania. To improve the oral health of their elderly dentate patients, dentists should apply all the available tools of chair-side prevention and active guidance. The latter would be an effective means of updating the knowledge of oral self-care and supporting recommended oral health behaviour. A preventive approach should be strongly emphasized in countries with limited resources for oral health care, such as Lithuania. Author’s address: Sonata Vyšniauskaite, Department of Oral Public Health, Institute of Dentistry, University of Helsinki, P.O.Box 41, FI-00014 Helsinki, Finland. E-mail: sonata.vysniauskaite@helsinki.fi

Oxidation of alkaline earth sulfides to sulfates: Thermodynamic aspects

The emf of the galvanic cell, Pt, Ni + NiO/(CaO) ZrO2/MS + MSO4, Ir, Pt, where M is calcium, strontium, or barium, has been measured in the temperature range 850 to 1100 K. From these measurements the Gibbs’ energy changes for the oxidation of sulfides of alkaline earth metals to their respective sulfates have been calculated. The results are compared with available thermodynamic data in the literature. The agreement varies from ±2 kJ for the strontium system to ±20 kJ in the case of barium. Trends in the stabilities of alkaline earth sulfates are discussed in relation to the properties of the cationic species involved.

Preparation of Industrially Important Hydroxy Acids and Diacids from 2,2-Disubstituted Propane-1,3-Diols and Linear Primary Diols by Green Chemistry Methods

Environmentally benign and economical methods for the preparation of industrially important hydroxy acids and diacids were developed. The carboxylic acids, used in polyesters, alkyd resins, and polyamides, were obtained by the oxidation of the corresponding alcohols with hydrogen peroxide or air catalyzed by sodium tungstate or supported noble metals. These oxidations were carried out using water as a solvent. The alcohols are also a useful alternative to the conventional reactants, hydroxyaldehydes and cycloalkanes. The oxidation of 2,2-disubstituted propane-1,3-diols with hydrogen peroxide catalyzed by sodium tungstate afforded 2,2-disubstituted 3-hydroxypropanoic acids and 1,1-disubstituted ethane-1,2-diols as products. A computational study of the Baeyer-Villiger rearrangement of the intermediate 2,2-disubstituted 3-hydroxypropanals gave in-depth data of the mechanism of the reaction. Linear primary diols having chain length of at least six carbons were easily oxidized with hydrogen peroxide to linear dicarboxylic acids catalyzed by sodium tungstate. The Pt/C catalyzed air oxidation of 2,2-disubstituted propane-1,3-diols and linear primary diols afforded the highest yield of the corresponding hydroxy acids, while the Pt, Bi/C catalyzed oxidation of the diols afforded the highest yield of the corresponding diacids. The mechanism of the promoted oxidation was best described by the ensemble effect, and by the formation of a complex of the hydroxy and the carboxy groups of the hydroxy acids with bismuth atoms. The Pt, Bi/C catalyzed air oxidation of 2-substituted 2-hydroxymethylpropane-1,3-diols gave 2-substituted malonic acids by the decarboxylation of the corresponding triacids. Activated carbon was the best support and bismuth the most efficient promoter in the air oxidation of 2,2-dialkylpropane-1,3-diols to diacids. In oxidations carried out in organic solvents barium sulfate could be a valuable alternative to activated carbon as a non-flammable support. In the Pt/C catalyzed air oxidation of 2,2-disubstituted propane-1,3-diols to 2,2-disubstituted 3-hydroxypropanoic acids the small size of the 2-substituents enhanced the rate of the oxidation. When the potential of platinum of the catalyst was not controlled, the highest yield of the diacids in the Pt, Bi/C catalyzed air oxidation of 2,2-dialkylpropane-1,3-diols was obtained in the regime of mass transfer. The most favorable pH of the reaction mixture of the promoted oxidation was 10. The reaction temperature of 40°C prevented the decarboxylation of the diacids.

Managing resistance to chemical treatments in stored products pests

This review focuses on key trends in resistance to chemical treatments in stored product pests, and advances in resistance management, with an emphasis on resistance to the fumigant phosphine. Findings: Phosphine resistance continues to be a major concern. In particular, phosphine resistance in Cryptolestes ferrugineus has emerged as a serious issue, with some populations exhibiting the strongest level detected so far for this fumigant. In response, a 'quick knock down test' has been established to deliver industry and scientists 'same day' advice on the resistance status of field samples; sulfuryl fluoride is being developed as a 'resistance breaker' and phosphine dosages are being revised to manage this problem. There has been major progress in identifying the genes responsible for phosphine resistance and the development of molecular resistance diagnostics for key pests. Several studies on Rhyzopertha dominica have demonstrated that molecular screening can be used to determine the frequency of resistance alleles in samples collected from farm storages. Despite on-going research in several pests, there is no definitive answer to the question of whether there is a fitness cost associated phosphine resistance, with some studies showing a clear cost and others none. Evidence continues to emerge of resistance to grain protectants, including the juvenile hormone analogue methoprene. The development and adoption of spinosad, as a next generation 'green' treatment, and the use of protectant combinations provides opportunities to counter the problem of protectant resistance.Directions for future research: A uniform set of protocols should be developed for phosphine resistance detection for all major species. It should combine 'quick tests' and molecular diagnostics to be adopted internationally. Research is required on the establishment of a decision making system that integrates newly developed grain protectants and fumigants, other alternative control methods, as well as an accurate and rapid resistance detection system for early warning of the emergence of new resistances.

Reaction of sulphuryl chlorofluoride with a few metals and metal oxides

Sulphuryl chlorofluoride has no observable reaction with metals and metal oxides at room temperature. Metals like copper, silver, iron, and zinc react with the chlorofluoride in the temperature range 200–400°C. Metal chlorides, metal fluorides and sulphur dioxide are the main products of these reactions. With the corresponding metal oxides, on the other hand, the respective metal sulphates are formed in addition to the metal chlorides and fluorides. In the case of lead and lead oxide, lead chlorofluoride is formed instead of lead chloride and lead fluoride. Sulphuryl fluoride is formed in small quantities in all these reactions by the decomposition of the chlorofluoride. Glass is not attacked by sulphuryl chlorofluoride below 500°C.

A simple triggered vacuum gap

A simple triggered vacuum gap has previously been described by the authors in this journal (see ibid., vol.5, 415, 1972). Further studies have resulted in improvement of the performance with regard to sensitivity and consistency of the trigger characteristics and immunity from bridging due to metal particles eroded from the arc. The earlier design suffered from rather frequent bridging of the auxiliary gap and showed rather wide scatter in its trigger characteristics. In the present design thermally stable materials like fused quartz, machinable ceramic 'Supramica 500' (Mycalex Corporation of America), lead titanate, barium titanate (LCC HTD) and silicon carbide have been used to insulate the trigger electrode from the cathode. Consistent triggerings free from bridging, at relatively low voltages of 200-400 V have been obtained.

Factors influencing kinetic and equilibrium behaviour of sodium ion exchange with strong acid cation resin

This study reports an investigation of the ion exchange treatment of sodium chloride solutions in relation to use of resin technology for applications such as desalination of brackish water. In particular, a strong acid cation (SAC) resin (DOW Marathon C) was studied to determine its capacity for sodium uptake and to evaluate the fundamentals of the ion exchange process involved. Key questions to answer included: impact of resin identity; best models to simulate the kinetics and equilibrium exchange behaviour of sodium ions; difference between using linear least squares (LLS) and non-linear least squares (NLLS) methods for data interpretation; and, effect of changing the type of anion in solution which accompanied the sodium species. Kinetic studies suggested that the exchange process was best described by a pseudo first order rate expression based upon non-linear least squares analysis of the test data. Application of the Langmuir Vageler isotherm model was recommended as it allowed confirmation that experimental conditions were sufficient for maximum loading of sodium ions to occur. The Freundlich expression best fitted the equilibrium data when analysing the information by a NLLS approach. In contrast, LLS methods suggested that the Langmuir model was optimal for describing the equilibrium process. The Competitive Langmuir model which considered the stoichiometric nature of ion exchange process, estimated the maximum loading of sodium ions to be 64.7 g Na/kg resin. This latter value was comparable to sodium ion capacities for SAC resin published previously. Inherent discrepancies involved when using linearized versions of kinetic and isotherm equations were illustrated, and despite their widespread use, the value of this latter approach was questionable. The equilibrium behaviour of sodium ions form sodium fluoride solution revealed that the sodium ions were now more preferred by the resin compared to the situation with sodium chloride. The solution chemistry of hydrofluoric acid was suggested as promoting the affinity of the sodium ions to the resin.

Rocket Propellant Combustion Studies in a Constant Volume Bomb

A constant volume window bomb has been used to measure the characteristic velocity (c*) of rocket propellants. Analysis of the combustion process inside the bomb including heat losses has been made. The experiments on double base and composite propellants have revealed some (i) basic heat transfer aspects inside the bomb and (ii) combustion characteristics of Ammonium Perchlorate-Polyester propellants. It has been found that combustion continues even beyond the peak pressure and temperature points. Lithium Fluoride mixed propellants do not seem to indicate significant differences in c*) though the low pressure deflagration limit is increased with percentage of Lithium Fluoride.

Mammalian spermatid specific protein, TP2, is a zinc metalloprotein with two finger motifs

An analysis of the recently reported cDNA derived amino acid sequences of mouse (Kleene and Flynn, J. Biol. Chem. , 17272–17277, 1987) and rat (Luersson Image ,Nucl. Acids Res. Image , 3585, 1989). TP2 has revealed the presence of two potential zinc finger motifs involving cysteine and histidine residues. TP2, as purified from rat elongating spermatids, is shown here to contain 0.2 atoms of zinc bound per molecule of the protein by atomic absorption spectroscopy. On incubation with 10 μM ZnCl2, Image , and subsequent exhaustive dialysis, TP2 had 2 atoms of zinc bound per molecule. The involvement of cysteine residues of TP2 in coordination with zinc was also suggested by the observation that TP2 could be labeled, Image , with iodoacetamidofluorescein only after preincubation of spermatid nuclei with EDTA. The zinc finger domains of TP2 may play an important role in initiation of chromatin condensation and /or cessation of transcriptional activity during mammalian spermiogenesis. DTT, Dithiothreitol; IAF, Iodoacetamido-fluorescein; SDS, Sodium dodecyl sulfate; PAGE, Polyacrylamide gel electrophoresis; PMSF, Phynyl methyl sulfonyl fluoride

Encapsulation and release of rifampicin using poly(vinyl pyrrolidone)-poly (methacrylic acid) polyelectrolyte capsules

Poly(vinyl pyrrolidone) and poly(methacrylic acid) multilayer capsules based on hydrogen bonding have been prepared by the layer-by-layer approach and used to encapsulate and release rifampicin, an antituberculosis drug. Removal of silica core using a buffer of ammonium fluoride and hydrofluoric acid at about pH 3 was found to produce better capsules than hydrofluoric acid alone. An eight-layered capsule had a wall thickness of 20 rim. Maximum encapsulation was found to be about 86 mu g at 40 degrees C with 1 +/- 0.2 x 10(6) capsules. Release studies showed a burst kind of release and maximum release was obtained above pH 7 where the capsules disintegrate rapidly thereby releasing the drug in a short period. Interactions studies with Mycobacterium smegmatis showed that the capsules were cytocompatible and the released drug functioned with the same efficacy as the free drug.

BDST modelling of sodium ion exchange column behaviour with strong acid cation resin in relation to coal seam water treatment

Reverse osmosis is the dominant technology utilized for desalination of saline water produced during the extraction of coal seam gas. Alternatively, ion exchange is of interest due to potential cost advantages. However, there is limited information regarding the column performance of strong acid cation resin for removal of sodium ions from both model and actual coal seam water samples. In particular, the impact of bed depth, flow rate, and regeneration was not clear. Consequently, this study applied Bed Depth Service Time (BDST) models to reveal that increasing sodium ion concentration and flow rates diminished the time required for breakthrough to occur. The loading of sodium ions on fresh resin was calculated to be ca. 71.1 g Na/kg resin. Difficulties in regeneration of the resin using hydrochloric acid solutions were discovered, with 86% recovery of exchange sites observed. The maximum concentration of sodium ions in the regenerant brine was found to be 47,400 mg/L under the conditions employed. The volume of regenerant waste formed was 6.2% of the total volume of water treated. A coal seam water sample was found to load the resin with only 53.5 g Na/kg resin, which was consistent with not only the co-presence of more favoured ions such as calcium, magnesium, barium and strontium, but also inefficient regeneration of the resin prior to the coal seam water test.