Dielectric properties of certain biological materials at microwave frequencies.

In the medical field, microwaves play a larger role for treatment than diagnosis. For the detection of diseases by microwave methods, it is essential to know the dielectric properties of biological materials. For the present study, a cavity perturbation technique was employed to determine the dielectric properties of these materials. Rectangular cavity resonators were used to measure the complex permittivity of human bile, bile stones, gastric juice and saliva. The measurements were carried out in the S and J bands. It is observed that normal and infected bile have different dielectric constant and loss tangent. Dielectric constant of infected bile and gastric juice varies from patient to patient. Detection and extraction of bile stone with possible method of treatment is also discussed.

Qualitative air flow modelling and analysis of data centre air conditioning as multiple jet array

This work identifies the importance of plenum pressure on the performance of the data centre. The present methodology followed in the industry considers the pressure drop across the tile as a dependant variable, but it is shown in this work that this is the only one independent variable that is responsible for the entire flow dynamics in the data centre, and any design or assessment procedure must consider the pressure difference across the tile as the primary independent variable. This concept is further explained by the studies on the effect of dampers on the flow characteristics. The dampers have found to introduce an additional pressure drop there by reducing the effective pressure drop across the tile. The effect of damper is to change the flow both in quantitative and qualitative aspects. But the effect of damper on the flow in the quantitative aspect is only considered while using the damper as an aid for capacity control. Results from the present study suggest that the use of dampers must be avoided in data centre and well designed tiles which give required flow rates must be used in the appropriate locations. In the present study the effect of hot air recirculation is studied with suitable assumptions. It identifies that, the pressure drop across the tile is a dominant parameter which governs the recirculation. The rack suction pressure of the hardware along with the pressure drop across the tile determines the point of recirculation in the cold aisle. The positioning of hardware in the racks play an important role in controlling the recirculation point. The present study is thus helpful in the design of data centre air flow, based on the theory of jets. The air flow can be modelled both quantitatively and qualitatively based on the results.

Delocalization and fragmentation of collective modes in doped 4He drops

We have investigated the fragmentation of collective modes in doped 4He drops in the framework of a finite-range density-functional theory, as well as the delocalization of the impurity inside the cluster. Our results indicate that the impurity is gradually delocalized inside the drop as the size of the latter increases. As an example, results are shown in the case of Xe-4HeN systems up to N=112.

Nucleation in supersaturated solutions 3He in 4He at negative pressure.

Depending on the 3He concentration, thermal nucleation in 3-4He supersaturated liquid mixtures at negative pressures may be originated either by bubble or by 3rich drop formation. We have investigated this phenomenon within a density-functional approach, determining the regions in the pressure¿3He-concentration plane where bubbles or drops likely drive the nucleation process. As an illustrative example, we also give the homogeneous nucleation pressure corresponding to 50 and 100 mK temperature.

Survey of coral lagoons of Laksbadweep Atolls using line intercept transect (LIT) technique

The present study aims at surveying the coral lagoons of four islands viz. Kavarathi, Kalpeni, Kadmat and Agathi, which include quantitative survey of the major benthic forms using Line Intercept Transect (LIT) technique and hydrographical study of these lagoon waters The distribution of PHC in the lagoons has also been followed to understand, the effects of introduction of flat bottomed ferry boats to the islands.From a biological monitoring stand point for the assessment of manmade disturbance of the coral reefs, it IS highly essential to identify faunal assemblages which will contain 'flag-stones' specIes as indicators of such disturbances. Among the known faunal assemblages In coral reefs the most diverse groups of sensitive species belongs to bryozoan assemblage. Therefore, the most common species of bryozoans distributed along the atolls and reef flats were collected and described in this work Along with this, bryozoans associated with coral from other parts of Indian ocean have also been added so as to provide a comprehensive picture of the distribution of bryozoans in the coral reefs.

Predictability Of Share Prices In India: A Study Of The Applicability Of Technical Analysis

In spite of the far longed practices of technical analysis by many participants in Indian stock market, none have arrived at the exact position of technical analysis as a tool for foretelling share prices. There is no evidence supporting that one has established its definite role in predicting the behaviour of share price and also to see the extent of validity (how far reliable) of technical tools in Indian stock market. The problem is the vacuum in the arena of securities market analysis where an unrecognised tool is practised, i.e., whether to hold on to technical analysis or to drop it. Again, as already stated in this chapter, its validity need not continue forever. It may become futile as happened in developed markets. Continuous practice of a tool, which is valid only during discontinuous times is also an error. The efficacy of different market phenomena in terms of their ability to foretell the extent and direction of the price movements and reliability thereof remain as not yet proved in. This requires further study in this area so that this controversy may be settled. A solution to the problem requires enquiring and establishing the applicability of technical analysis, if any, there is in the Indian stock market. The study has the following two broad objectives for the purpose of confirming the applicability, if any, of technical analysis in the Indian stock market. The first objective is to ascertain the current validity of ‘traditional holding with respect to patterns’ and the second objective is to ascertain the ‘consistent superiority’, if any, of technical indicators over non-signal strategies in return generation. The study analyses the five patterns, which are widely known and commonly found in publications. They are: (1) Symmetrical Triangles, (2) Rising Wedges, (3) Falling Wedges, (4) Head and Shoulders Top and (5) Head and Shoulders Bottom.

“Qualitative Air Flow Modelling And Analysis Of Data Centre Air Conditioning As Multiple Jet Array

In the present study the effect of hot air recirculation is studied with suitable assumptions. It identifies that, the pressure drop across the tile is a dominant parameter which governs the recirculation. The rack suction pressure of the hardware along with the pressure drop across the tile determines the point of recirculation in the cold aisle. The positioning of hardware in the racks play an important role in controlling the recirculation point. The present study is thus helpful in the design of data centre air flow, based on the theory of jets. The air flow can be modelled both quantitatively and qualitatively based on the results

Estimation of temperature effects on fission barriers

An accurate mass formula at finite temperature has been used to obtain a more precise estimation of temperature effects on fission barriers calculated within the liquid drop model.

“Studies on new base materials for microcellular soles"

The most important part of any footwear is the sole (or sole and heel) which withstands all the hannful external factors such as rouglmess of the ground or road, sharp objects, thorns and stones, heat, dampness and cold during walking. The properties desirable in soling material, therefore, would be 1. lightness 2. resistance to wear and tear for long service life 3. flexibility/softness for wearing comfort 4. thennal insulation Rubber soling surpasses all other soling materials in better performance and lower cost. Because MC sole is soft and very light, and has good abrasion resistance, flex properties and set behaviour it has become very popular all over the world and demand for better quality product is ever increasing. Due to the traditional approach adopted by the footwear industry in foot wear design, the rubber based footwear export surprisingly contributes only a small percentage. The essence of success for any industry lies in the expansion of the export market. Microcellular soles are manufactured for the last three decades without much change in the traditional design and colour pattern. In recent years domestic customers have also started demanding better quality products. In view of the changing taste of the customer and growing competition from other countries, substantial improvement in the export potential will require new base materials for regular or fashion rubber based footwears. The main objective of the present study is to develop new base materials for making MC soles with good quality, viz., light weight, durability and bright colours

A structural investigation relating to the pozzolanic activity of rice husk ashes

Various factors determine the applicability of rice husk ash (RHA) as a pozzolanic material. The amount and accessibility of reactive sites is thought to be a key factor. A structural study of RHA samples in relation to their reactivity has been performed; Silica in RHA formed by burning rice husk in a laboratory furnace under continuous supply of air have been characterized as a function of incineration temperature, time and cooling regime. The characterization methods included chemical analyses, conductivity measurements, microscopic analysis, X-ray diffraction (XRD) and 29Si magic-angle spinning (MAS) nuclear magnetic resonance (NMR). In line with earlier observations, the analyses show that the highest amounts of amorphous silica occur in samples burnt in the range of 500 °C–700 °C. The 29Si NMR data allow direct identification of the reactive silanol sites in the RHA samples. De-convolution of the NMR spectra clearly shows that the quickly cooled RHA resulting from burning rice husk for 12 h at 500 °C has the highest amount of silanol groups. This sample also induced the largest drop in conductivity when added to a saturated calcium hydroxide solution giving an indication of its reactivity towards lime. Therefore, this RHA is the favorable sample to be used as pozzolanic cement additive

β-glucosidases from Aspergillus unguis NII 08123: Molecular characterization, properties and applications

Lignocellulosic biomass is probably the best alternative resource for biofuel production and it is composed mainly of cellulose, hemicelluloses and lignin. Cellulose is the most abundant among the three and conversion of cellulose to glucose is catalyzed by the enzyme cellulase. Cellulases are groups of enzymes act synergistically upon cellulose to produce glucose and comprise of endoglucanase, cellobiohydrolase and β-glucosidase. β -glucosidase assumes great importance due to the fact that it is the rate limiting enzyme. Endoglucanases (EG) produces nicks in the cellulose polymer exposing reducing and non reducing ends, cellobiohydrolases (CBH) acts upon the reducing or non reducing ends to liberate cellobiose units, and β - glucosidases (BGL) cleaves the cellobiose to liberate glucose completing the hydrolysis. . β -glucosidases undergo feedback inhibition by their own product- β glucose, and cellobiose which is their substrate. Few filamentous fungi produce glucose tolerant β - glucosidases which can overcome this inhibition by tolerating the product concentration to a particular threshold. The present study had targeted a filamentous fungus producing glucose tolerant β - glucosidase which was identified by morphological as well as molecular method. The fungus showed 99% similarity to Aspergillus unguis strain which comes under the Aspergillus nidulans group where most of the glucose tolerant β -glucosidase belongs. The culture was designated the strain number NII 08123 and was deposited in the NII culture collection at CSIR-NIIST. β -glucosidase multiplicity is a common occurrence in fungal world and in A.unguis this was demonstrated using zymogram analysis. A total 5 extracellular isoforms were detected in fungus and the expression levels of these five isoforms varied based on the carbon source available in the medium. Three of these 5 isoforms were expressed in higher levels as identified by the increased fluorescence (due to larger amounts of MUG breakdown by enzyme action) and was speculated to contribute significantly to the total _- β glucosidase activity. These isoforms were named as BGL 1, BGL3 and BGL 5. Among the three, BGL5 was demonstrated to be the glucose tolerant β -glucosidase and this was a low molecular weight protein. Major fraction was a high molecular weight protein but with lesser tolerance to glucose. BGL 3 was between the two in both activity and glucose tolerance.121 Glucose tolerant .β -glucosidase was purified and characterized and kinetic analysis showed that the glucose inhibition constant (Ki) of the protein is 800mM and Km and Vmax of the enzyme was found to be 4.854 mM and 2.946 mol min-1mg protein-1respectively. The optimumtemperature was 60°C and pH 6.0. The molecular weight of the purified protein was ~10kDa in both SDS as well as Native PAGE indicating that the glucose tolerant BGL is a monomeric protein.The major β -glucosidase, BGL1 had a pH and temperature optima of 5.0 and 60 °C respectively. The apparent molecular weight of the Native protein is 240kDa. The Vmax and Km was 78.8 mol min-1mg protein-1 and 0.326mM respectively. Degenerate primers were designed for glycosyl hydrolase families 1, 3 and 5 and the BGL genes were amplified from genomic DNA of Aspergillus unguis. The sequence analyses performed on the amplicons results confirmed the presence of all the three genes. Amplicon with a size of ~500bp was sequenced and which matched to a GH1 –BGL from Aspergillus oryzae. GH3 degenerate primers producing amplicons were sequenced and the sequences matched to β - glucosidase of GH3 family from Aspergillus nidulans and Aspergillus acculateus. GH5 degenerate primers also gave amplification and sequencing results indicated the presence of GH5 family BGL gene in the Aspergillus unguis genomic DNA.From the partial gene sequencing results, specific as well as degenerate primers were designed for TAIL PCR. Sequencing results of the 1.0 Kb amplicon matched Aspergillus nidulans β -glucosidase gene which belongs to the GH1 family. The sequence mainly covered the N-Terminal region of the matching peptide. All the three BGL proteins ie. BGL1, BGL3 and BGL5 were purified by chromatography an electro elution from Native PAGE gels and were subjected to MALDI-TOF mass spectrometric analysis. The results showed that BGL1 peptide mass matched to . β -glucosidase-I of Aspergillus flavus which is a 92kDa protein with 69% protein coverage. The glucose tolerant β -glucosidase BGL5 mass matched to the catalytic C-terminal domain of β -glucosidase-F from Emericella nidulans, but the protein coverage was very low compared to the size of the Emericella nidulans protein. While comparing the size of BGL5 from Aspergillus unguis, the protein sequence coverage is more than 80%. BGL F is a glycosyl hydrolase family 3 protein.The properties of BGL5 seem to be very unique, in that it is a GH3 β -glucosidase with a very low molecular weight of ~10kDa and at the same time having catalytic activity and glucose 122 tolerance which is as yet un-described in GH β -glucosidases. The occurrence of a fully functional 10kDA protein with glucose tolerant BGL activity has tremendous implications both from the points of understanding the structure function relationships as well as for applications of BGL enzymes. BGL-3 showed similarity to BGL1 of Aspergillus aculateus which was another GH3 β -glucosidase. It may be noted that though PCR could detect GH1, GH3 and GH5 β-glucosidases in the fungus, the major isoforms BGL1 BGL3 and BGL5 were all GH3 family enzymes. This would imply that β-glucosidases belonging to other families may also co-exist in the fungus and the other minor isoforms detected in zymograms may account for them. In biomass hydrolysis, GT-BGL containing BGL enzyme was supplemented to cellulase and the performances of blends were compared with a cocktail where commercial β- glucosidase was supplemented to the biomass hydrolyzing enzyme preparation. The cocktail supplemented with A unguis BGL preparation yielded 555mg/g sugar in 12h compared to the commercial enzyme preparation which gave only 333mg/g in the same period and the maximum sugar yield of 858 mg/g was attained in 36h by the cocktail containing A. unguis BGL. While the commercial enzyme achieved almost similar sugar yield in 24h, there was rapid drop in sugar concentration after that, indicating probably the conversion of glucose back to di-or oligosaccharides by the transglycosylation activity of the BGl in that preparation. Compared this, the A.unguis enzyme containing preparation supported peak yields for longer duration (upto 48h) which is important for biomass conversion to other products since the hydrolysate has to undergo certain unit operations before it goes into the next stage ie – fermentation in any bioprocesses for production of either fuels or chemicals.. Most importantly the Aspergillus unguis BGL preparation yields approximately 1.6 fold increase in the sugar release compared to the commercial BGL within 12h of time interval and 2.25 fold increase in the sugar release compared to the control ie. Cellulase without BGL supplementation. The current study therefore leads to the identification of a potent new isolate producing glucose tolerant β - glucosidase. The organism identified as Aspergillus unguis comes under the Aspergillus nidulans group where most of the GT-BGL producers belong and the detailed studies showed that the glucose tolerant β -glucosidase was a very low molecular weight protein which probably belongs to the glycosyl hydrolase family 3. Inhibition kinetic studies helped to understand the Ki and it is the second highest among the nidulans group of Aspergilli. This has promoted us for a detailed study regarding the mechanism of glucose tolerance. The proteomic 123 analyses clearly indicate the presence of GH3 catalytic domain in the protein. Since the size of the protein is very low and still its active and showed glucose tolerance it is speculated that this could be an entirely new protein or the modification of the existing β -glucosidase with only the catalytic domain present in it. Hydrolysis experiments also qualify this BGL, a suitable candidate for the enzyme cocktail development for biomass hydrolysis

Dye-sensitized solar cells based on perylene derivatives

The oil price rises more and more, and the world energy consumption is projected to expand by 50 percent from 2005 to 2030. Nowadays intensive research is focused on the development of alternative energies. Among them, there are dye-sensitized nanocrystalline solar cells (DSSCs) “the third generation solar cells”. The latter have gained attention during the last decade and are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic. At present DSSCs with ruthenium based dyes exhibit highest efficiencies (ca 11%). The objective of the present work is to fabricate, characterize and improve the performance of DSSCs based on metal free dyes as sensitizers, especially on perylene derivatives. The work begins by a general introduction to the photovoltaics and dye-sensitized solar cells, such as the operating principles and the characteristics of the DSSCs. Chapter 2 and 3 discuss the state of the art of sensitizers used in DSSCs, present the compounds used as sensitizer in the present work and illustrate practical issues of experimental techniques and device preparation. A comparative study of electrolyte-DSSCs based on P1, P4, P7, P8, P9, and P10 are presented in chapter 4. Experimental results show that the dye structure plays a crucial role in the performance of the devices. The dye based on the spiro-concept (bipolar spiro compound) exhibited a higher efficiency than the non-spiro compounds. The presence of tert-butylpyridine as additive in the electrolyte was found to increase the open circuit voltage and simultaneously decrease the efficiency. The presence of lithium ions in the electrolyte increases both output current and the efficiency. The sensitivity of the dye to cations contained in the electrolyte was investigated in the chapter 5. FT-IR and UV-Vis were used to investigate the in-situ coordination of the cation to the adsorbed dye in the working devices. The open-circuit voltage was found to depend on the number of coordination sites in the dye. P1 with most coordination sites has shown the lowest potential drop, opposite to P7, which is less sensitive to cations in the working cells. A strategy to improve the dye adsorption onto the TiO2 surface, and thus the light harvesting efficiency of the photoanode by UV treatment, is presented in chapter 6. The treatment of the TiO2 film with UV light generates hydroxyl groups and renders the TiO2 surface more and more hydrophilic. The treated TiO2 surface reacts readily with the acid anhydride group of the dye that acts as an anchoring group and improves the dye adsorption. The short-circuit current density and the efficiency of the electrolyte-based dye cells was considerably improved by the UV treatment of the TiO2 film. Solid-state dye-sensitized solar cells (SSDs) based on spiro-MeOTAD (used as hole transport material) are studied in chapter 7. The efficiency of SSDs was globally found to be lower than that of electrolyte-based solar cells. That was due to poor pore filling of the dye-loaded TiO2 film by the spin-coated spiro-MeOTAD and to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator. However, the presence of the donor moieties in P1 that are structurally similar to spiro-MeOTAD was found to improve the wettability of the P1-loaded TiO2 film. As a consequence the performance of the P1-based solid-state cells is better compared to the cells based on non-spiro compounds.

Akzeptanz und Motivation beim selbstregulierten Lernen unter Einsatz von neuen Medien in der berufsbegleitenden Weiterbildung

Das Ziel der Dissertation war die Untersuchung des Computereinsatzes zur Lern- und Betreuungsunterstützung beim selbstgesteuerten Lernen in der Weiterbildung. In einem bisher konventionell durchgeführten Selbstlernkurs eines berufsbegleitenden Studiengangs, der an das Datenmanagement der Bürodatenverarbeitung heranführt, wurden die Kursunterlagen digitalisiert, die Betreuung auf eine online-basierte Lernbegleitung umgestellt und ein auf die neuen Lernmedien abgestimmtes Lernkonzept entwickelt. Dieses neue Lernkonzept wurde hinsichtlich der Motivation und der Akzeptanz von digitalen Lernmedien evaluiert. Die Evaluation bestand aus zwei Teilen: 1. eine formative, den Entwicklungsprozess begleitende Evaluation zur Optimierung der entwickelten Lernsoftware und des eingeführten Lernkonzeptes, 2. eine sowohl qualitative wie quantitative summative Evaluation der Entwicklungen. Ein zentraler Aspekt der Untersuchung war die freie Wahl der Lernmedien (multimediale Lernsoftware oder konventionelles Begleitbuch) und der Kommunikationsmedien (online-basierte Lernplattform oder die bisher genutzten Kommunikationskanäle: E-Mail, Telefon und Präsenztreffen). Diese Zweigleisigkeit erlaubte eine differenzierte Gegenüberstellung von konventionellen und innovativen Lernarrangements. Die Verbindung von qualitativen und quantitativen Vorgehensweisen, auf Grund derer die subjektiven Einstellungen der Probanden in das Zentrum der Betrachtung rückten, ließen einen Blickwinkel auf den Nutzen und die Wirkung der Neuen Medien in Lernprozessen zu, der es erlaubte einige in der Literatur als gängig angesehene Interpretationen in Frage zu stellen und neu zu diskutieren. So konnten durch eine Kategorisierung des Teilnehmerverhaltens nach online-typisch und nicht online-typisch die Ursache-Wirkungs-Beziehungen der in vielen Untersuchungen angeführten Störungen in Online-Seminaren verdeutlicht werden. In den untersuchten Kursen zeigte sich beispielsweise keine Abhängigkeit der Drop-out-Quote von den Lern- und Betreuungsformen und dass diese Quote mit dem neuen Lernkonzept nur geringfügig beeinflusst werden konnte. Die freie Wahl der Lernmedien führte zu einer gezielten Nutzung der multimedialen Lernsoftware, wodurch die Akzeptanz dieses Lernmedium stieg. Dagegen war die Akzeptanz der Lernenden gegenüber der Lernbegleitung mittels einer Online-Lernplattform von hoch bis sehr niedrig breit gestreut. Unabhängig davon reichte in allen Kursdurchgängen die Online-Betreuung nicht aus, so dass Präsenztreffen erbeten wurde. Hinsichtlich der Motivation war die Wirkung der digitalen Medien niedriger als erwartet. Insgesamt bieten die Ergebnisse Empfehlungen für die Planung und Durchführung von computerunterstützten, online-begleiteten Kursen.

Ermittlung geeigneter Methoden zur Differenzierung und Qualitätsbeurteilung unterschiedlicher Milchqualitäten aus verschiedenen on-farm-Experimenten

Zusammenfassung: Ziel der Arbeit war ein Methodenvergleich zur Beurteilung der Milchqualität unterschiedlicher Herkünfte. Am Beispiel von Milchproben aus unterschiedlicher Fütterung sowie an Milchproben von enthornten bzw. horntragenden Kühen wurde geprüft, welche der angewendeten Methoden geeignet ist, die Vergleichsproben zu unterscheiden (Differenzierungsfähigkeit der Methoden) und inwieweit eine Qualitätsbeurteilung möglich ist (hinsichtlich Milchleistung, Fett-, Eiweiß-, Lactose- (=F,E,L), Harnstoff-gehalt und Zellzahl (=SCC), Säuerungseigenschaften (=SE), Fettsäuremuster (=FS-Muster), Protein- und Metabolit-Zusammensetzung (=Pr&M), Fluoreszenz-Anregungs-Spektroskopie-Eigenschaften (=FAS) und Steigbild-Merkmalen). Zusätzlich wurde vorab die Steigbildmethode (=SB-M) für das Produkt Rohmilch standardisiert und charakterisiert, um die Reproduzierbarkei der Ergebnisse sicherzustellen. Die Untersuchungen zur SB-M zeigten, dass es Faktoren gibt, die einen deutlichen Einfluß auf die Bildmerkmals-Ausprägung aufweisen. Dazu gehören laborseitig die Klimabedingungen in der Kammer, die Verdünnungsstufe der Probe, die Standzeiten der Vorverdünnung (Reaktionen mit der Luft, Alterung usw.), und tagesspezifisch auftretende Effekte, deren Ursache unbekannt ist. Probenseitig sind sehr starke tierindividuelle Effekte auf die Bildmerkmals-Ausprägung festzustellen, die unabhängig von Fütterung, Alter, Laktationsstadium und Genetik auftreten, aber auch Fütterungsbedingungen der Kühe lassen sich in der Bildmerkmals-Ausprägung wiederfinden. Die Art der Bildauswertung und die dabei berücksichtigten Bildmerkmale ist von großer Bedeutung für das Ergebnis. Die im Rahmen dieser Arbeit untersuchten 46 Probenpaare (aus den Fütterungsvergleichen (=FV) und zur Thematik der Hörner) konnten in 91% der Fälle korrekt gruppiert werden. Die Unterschiede konnten benannt werden. Drei FV wurden auf drei biologisch-dynamischen Höfen unter Praxis-Bedingungen durchgeführt (on-farm-Experimente). Es wurden jeweils zwei vergleichbare Gruppen à mindestens 11 Kühen gebildet, die im Cross-Over-Design gefüttert wurden, mit Probennahme am 14. und 21. Tag je Periode. Es wurden folgende FV untersucht: A: Wiesenheu vs. Kleegrasheu (=KG-Heu), B: Futterrüben (=FuR) vs. Weizen (Ergänzung zu Luzernegrasheu ad lib.), C: Grassilage vs. Grasheu. Bei Versuch A sind die Futtereffekte am deutlichsten, Gruppeneffekte sind gering. Die Milch der Wiesenheu-Variante hat weniger CLA’s und n3- FS und mehr mittellangkettige FS (MCT-FS), das Pr&M-Muster weist auf „Gewebereifung und Ausdifferenzierung“ vs. bei KG-Heu „Nährstoff-fülle, Wachstum und Substanz-Einlagerung und die SB zeigen fein ausdifferenzierte Bildmerkmale. Bei Versuch B sind die Futtereffekte ähnlich groß wie die Gruppeneffekte. Bei vergleichbarer Milchleistung weist die Milch der FuR-Variante höhere F- und E-Gehalte auf, sie säuert schneller und mehr, das FS-Muster weist auf eine „intensive“ Fütterung mit vermehrt MCT- FS, und die Pr&M-Untersuchungen charakterisieren sie mit „Eisentransport und Fetttröpfchenbildung“ vs. bei Weizen „mehr Abwehr-, Regulations- und Transportfunktion“ /. „mehr Lipidsynthese“. Die SB charakterisieren mit „große, kräftige Formen, verwaschen“ vs. „kleine, ausdifferenzierte Bildmerkmal“ für FuR vs. Weizen. Die FAS charakterisiert sie mit „Saftfutter-typisch“ vs. „Samentypisch“. Versuch C weist die geringsten Futtereffekt auf, und deutliche Gruppen- und Zeiteffekte. Milchleistung und F,E,L-Gehalte zeigen keinen Futtereffekt. Die Milch der Heu-Variante säuert schneller, und sie weist mehr SCT und MCT- FS auf. Pr&M-Untersuchungen wurden nicht durchgeführt. Die SB charakterisieren bei Heumilch mit „fein, zart, durchgestaltet, hell“, bei Silagemilch mit „kräftig, wäßrig-verwaschen, dunkler“. Die FAS kann keine konsistenten Unterschiede ermitteln. Der Horn-Einfluß auf die Milchprobe wurde an 34 Probenpaaren untersucht. Von 11 Höfen wurden je zwei möglichst vergleichbare Gruppen zusammengestellt, die sich nur im Faktor „Horn“ unterscheiden, und im wöchentlichen Abstand drei mal beprobt. F,E,L, SCC und SE der Proben sowie die FAS-Messungen weisen keine konsistenten signifikanten Unterschiede zwischen den Horn-Varianten auf. Pr&M weisen bei den untersuchten Proben (von zwei Höfen) auf Horneffekte hin: bei Eh eine Erhöhung von Immun-Abwehr-Funktionen, sowie einer Abnahme phosphorylierter C3- und C6-Metabolite und Beta-Lactoglobulin. Mit den SB ließen sich für die gewählten Merkmale (S-Größe und g.B.-Intensität) keine Horneffekte feststellen. FS, Pr&M-Muster sowie Harnstoffgehalt und SB (und z.T. Milchleistung) zeigten je FV ähnliche Effekt-Intensitäten für Futter-, Gruppen- und Zeiteffekte, und konnten die Cross-Over-Effekte gut wiedergeben. F- und E-Gehalte konnten neben tierindividuellen Effekten nur in FV B auch Futtereffekte aufzeigen. In FV C zeigten die SE der Proben den deutlichsten Futtereffekt, die anderen Methoden zeigten hier vorrangig Gruppen-Effekte, gefolgt von Futter- und Zeiteffekten. Die FAS zeigte den SB vergleichbare Ergebnisse, jedoch weniger sensibel reagierend. Die Interpretation von Qualitätsaspekten war bei konsistent differenzierbaren Proben (FV A, B, C) am fundiertesten mit Hilfe der FS möglich, da über die Synthese von FS und beeinflussende Faktoren schon vielfältige Erkenntnisse vorliegen. Das Pr&M-Muster war nach einer weiteren Methodenentwicklung bei der Deutung von Stoffwechselprozessen sehr hilfreich. Die FAS konnte z.T. eine zu der Fütterungsvariante passende Charakterisierung liefern. Für die SB-M fehlt es noch an Referenzmaterial, um Angaben zu Qualitätsaspekten zu machen, wenngleich Probenunterschiede aufgezeigt und Proben-Eigenschaften charakterisiert werden konnten.

The social dimension: a neglected policy item in the Bologna Process

Since its beginning in 1999, the Bologna Process has influenced various aspects of higher education in its member countries, e.g., degree structures, mobility, lifelong learning, social dimension and quality assurance. The social dimension creates the focus of this research. The social dimension entered the Bologna Process agenda in 2001. Despite a decade of reforms, it somehow remained as a vague element and received low scholarly attention. This research addresses to this gap. Firstly, different meanings of the social dimension according to the major European policy actors are analysed. Unfolding the understandings of the actors revealed that the social dimension is mostly understood in terms reflecting the diversity of population on the student body accessing to, progressing in and completing higher education, with a special concern on the underrepresented groups. However, it is not possible to observe a similar commonality concerning the actual policy measures to achieve this goal. Divergence occurs with respect to the addressed underrepresented groups, i.e., all underrepresented groups or people without formal qualifications and mature learners, and the values and institutional interests traditionally promoted by these actors. Secondly, the dissertation discusses the reflection of this social dimension understanding at the national level by looking at cases of Finland, Germany and Turkey. The in-depth analyses show an awareness of the social dimension among most of the national Bologna Process actors and a common understanding of the social dimension goals. However, this understanding has not triggered action in any of the countries. The countries acted on areas which they defined problematic before the Bologna Process. Finally, based on these findings the dissertation discusses the social dimension as a policy item that managed to get into the Bologna Process agenda, but neither grew into an implementable policy, nor drop out of it. To this aim, it makes use of the multiple streams framework and explains the low agenda status social dimension with: i. the lack of a pressing problem definition: the lack of clearly defined indicators and a comprehensive monitoring system, ii. the lack of a viable solution alternative: the proposal of developing national strategies and action plans closed the way to develop generic guidelines for the social dimension to be translated into national policy processes, iii. low political perceptivity: the recent trends opt for increasing efficiency, excellence and exclusiveness discourses rather than ensuring equality and inclusiveness iv. high constraints: the social dimension by definition requires more public funding which is less appreciated and strategic constraints of the actors in allocating their resources v. the type of policy entrepreneur: the social dimension is promoted by an international stakeholder, the European Students’ Union, instead of the ministers responsible for higher education The social dimension remains a policy item in the Bologna Process which is noble enough to agree but not urgent enough to act on.