Confocal microscopy applied to the study of single entity fluorescence and light scattering

A sample scanning confocal optical microscope (SCOM) was designed and constructed in order to perform local measurements of fluorescence, light scattering and Raman scattering. This instrument allows to measure time resolved fluorescence, Raman scattering and light scattering from the same diffraction limited spot. Fluorescence from single molecules and light scattering from metallic nanoparticles can be studied. First, the electric field distribution in the focus of the SCOM was modelled. This enables the design of illumination modes for different purposes, such as the determination of the three-dimensional orientation of single chromophores. Second, a method for the calculation of the de-excitation rates of a chromophore was presented. This permits to compare different detection schemes and experimental geometries in order to optimize the collection of fluorescence photons. Both methods were combined to calculate the SCOM fluorescence signal of a chromophore in a general layered system. The fluorescence excitation and emission of single molecules through a thin gold film was investigated experimentally and modelled. It was demonstrated that, due to the mediation of surface plasmons, single molecule fluorescence near a thin gold film can be excited and detected with an epi-illumination scheme through the film. Single molecule fluorescence as close as 15nm to the gold film was studied in this manner. The fluorescence dynamics (fluorescence blinking and excited state lifetime) of single molecules was studied in the presence and in the absence of a nearby gold film in order to investigate the influence of the metal on the electronic transition rates. The trace-histogram and the autocorrelation methods for the analysis of single molecule fluorescence blinking were presented and compared via the analysis of Monte-Carlo simulated data. The nearby gold influences the total decay rate in agreement to theory. The gold presence produced no influence on the ISC rate from the excited state to the triplet but increased by a factor of 2 the transition rate from the triplet to the singlet ground state. The photoluminescence blinking of Zn0.42Cd0.58Se QDs on glass and ITO substrates was investigated experimentally as a function of the excitation power (P) and modelled via Monte-Carlo simulations. At low P, it was observed that the probability of a certain on- or off-time follows a negative power-law with exponent near to 1.6. As P increased, the on-time fraction reduced on both substrates whereas the off-times did not change. A weak residual memory effect between consecutive on-times and consecutive off-times was observed but not between an on-time and the adjacent off-time. All of this suggests the presence of two independent mechanisms governing the lifetimes of the on- and off-states. The simulated data showed Poisson-distributed off- and on-intensities, demonstrating that the observed non-Poissonian on-intensity distribution of the QDs is not a product of the underlying power-law probability and that the blinking of QDs occurs between a non-emitting off-state and a distribution of emitting on-states with different intensities. All the experimentally observed photo-induced effects could be accounted for by introducing a characteristic lifetime tPI of the on-state in the simulations. The QDs on glass presented a tPI proportional to P-1 suggesting the presence of a one-photon process. Light scattering images and spectra of colloidal and C-shaped gold nano-particles were acquired. The minimum size of a metallic scatterer detectable with the SCOM lies around 20 nm.

Hochgenaue Berechnungen von Energien und molekularen Eigenschaften mit Hilfe der Coupled-Cluster-Theorie

Coupled-Cluster-Theorie (CC) ist in der heutigen Quantenchemie eine der erfolgreichsten Methoden zur genauen Beschreibung von Molekülen. Die in dieser Arbeit vorgestellten Ergebnisse zeigen, daß neben den Berechnungen von Energien eine Reihe von Eigenschaften wie Strukturparameter, Schwingungsfrequenzen und Rotations-Schwingungs-Parameter kleiner und mittelgrofler Moleküle zuverlässig und präzise vorhergesagt werden können. Im ersten Teil der Arbeit wird mit dem Spin-adaptierten Coupled-Cluster-Ansatz (SA-CC) ein neuer Weg zur Verbesserung der Beschreibung von offenschaligen Systemen vorgestellt. Dabei werden zur Bestimmung der unbekannten Wellenfunktionsparameter zusätzlich die CC-Spingleichungen gelöst. Durch dieses Vorgehen wird gewährleistet, daß die erhaltene Wellenfunktion eine Spineigenfunktion ist. Die durchgeführte Implementierung des Spin-adaptierten CC-Ansatzes unter Berücksichtigung von Einfach- und Zweifachanregungen (CCSD) für high-spin Triplett-Systeme wird ausführlich erläutert. Im zweiten Teil werden CC-Additionsschemata vorgestellt, die auf der Annahme der Additivität von Elektronenkorrelations- und Basissatzeffekten basieren. Die etablierte Vorgehensweise, verschiedene Beiträge zur Energie mit an den Rechenaufwand angepassten Basissätzen separat zu berechnen und aufzusummieren, wird hier auf Gradienten und Kraftkonstanten übertragen. Für eine Beschreibung von Bindungslängen und harmonischen Schwingungsfrequenzen mit experimenteller Genauigkeit ist die Berücksichtigung von Innerschalenkorrelationseffekten sowie Dreifach- und Vierfachanregungen im Clusteroperator der Wellenfunktion nötig. Die Basissatzkonvergenz wird dabei zusätzlich mit Extrapolationsmethoden beschleunigt. Die quantitative Vorhersage der Bindungslängen von 17 kleinen Molekülen, aufgebaut aus Atomen der ersten Langperiode, ist so mit einer Genauigkeit von wenigen Hundertstel Pikometern möglich. Für die Schwingungsfrequenzen dieser Moleküle weist das CC-Additionsschema basierend auf den berechneten Kraftkonstanten im Vergleich zu experimentellen Ergebnissen einen mittleren absoluten Fehler von 3.5 cm-1 und eine Standardabweichung von 2.2 cm-1 auf. Darüber hinaus werden zur Unterstützung von experimentellen Untersuchungen berechnete spektroskopische Daten einiger größerer Moleküle vorgelegt. Die in dieser Arbeit vorgestellten Untersuchungen zur Isomerisierung von Dihalogensulfanen XSSX (X= F, Cl) oder die Berechnung von Struktur- und Rotations-Schwingungs-Parametern für die Moleküle CHCl2F und CHClF2 zeigen, daß bereits störungstheoretische CCSD(T)-Näherungsmethoden qualitativ gute Vorhersagen experimenteller Resultate liefern. Desweiteren werden Diskrepanzen von experimentellen und berechneten Bindungsabständen bei den Molekülen Borhydrid- und Carbenylium durch die Berücksichtigung des elektronischen Beitrages zum Trägheitsmoment beseitigt.

Synthese und Photochemie von Dendrimeren mit stilbenoiden Chromophoren

Dendrimere spielen als strukturtreue Nanopartikel eine herausragende Rolle. Ziel dieser Arbeit war, Dendrimere mit einer hohen Dichte an photoaktiven Chromophoren herzu-stellen und zu untersuchen. Dazu wurden die terminalen Aminogruppen von Poly(propylenimin)dendrimeren 1. und 2. Generation, Astramol DAB-Am-4R und DAB-Am-8R, mit Stilbenen und Styrylstilbenen als Chromophor verknüpft. Mittels Wittig-Horner- und Heck-Reaktion wurden (E)-Stilbene aufgebaut, die auf der einen Seite drei Propoxygruppen zur Verbesserung der Löslichkeit und auf der anderen Seite eine passende Funktionalität zur Verknüpfung mit dem dendritischen Core tragen. Als Verknüpfungsmethoden wurden die Verknüpfung als Amid (PSDA), Schiffsche Base (PSDS) und Harnstoff (PSDH) getestet. Die Schiffschen Basen wurden außerdem zur Erhöhung der Hydrolysestabilität zum sekundären Amin reduziert (PSDR und PQDR). Durch die Verknüpfung mit dem Core werden die stilbenoiden Chromophore sehr stark photoaktiviert. Das beruht auf einem Singulett-Energietransfer (Förster-Mechanismus) von Chromophor zu Chromophor. Dieser Prozeß konkurriert zu den Deaktivierungsprozessen, verlängert die mittlere S1-Lebensdauer und erhöht somit die Chancen der Photochemie. Der Styrylstilben-Chromophor hat darüber hinaus einen erheblichen Teil seiner UV-Absorbtion bereits im Tageslicht und photopolymerisiert daher bereits im Tageslicht. Vor allem bei den Dendrimeren 2. Generation stellte sich die Frage nach der vollständigen, d.h. achtfachen Umsetzung; das Core sollte als Knäuel vorliegen, die Arme zum Teil nach innen gefaltet und somit dem Reaktand nur bedingt zugänglich. Auch dort konnten unter optimierten Reaktionsbedingungen alle Aminogruppen umgesetzt werden. Die vollständige Umsetzung der Dendrimere wurde mittels NMR und massenspektroskopischen Methoden untersucht. Bei den Absorptionsspektren der Dendrimere 1. Generation ändert sich die Lage der Maxima je nach Art der Verknüpfung der Chromophore mit dem Core. Die Verlängerung des Chromophors um eine Styryleinheit bedingt eine beträchtliche Rotverschiebung. Die Lage der Emissionsmaxima differiert stärker als die Lage der Absorptionsmaxima. Den geringsten Stokes-Shift weist der Harnstoff auf, dann folgt das sekundäre Amin, dann die Schiffsche Base. Dies weist auf unterschiedlich relaxierte S1-Geometrien hin. Die Verbindungen PSDS1, PSDR1 und PSDH1 aus 3,4,5-Tripropoxystilbeneinheit und Astramol-Core 1. Generation DAB-Am-4 wurden in einer Konzentration von 10-5 mol/L belichtet. Der vollständige Photoabbau durch Belichtung in Chloroform mit einer Xenon-Lampe erfolgte ohne jeglichen Filter innerhalb von zehn Minuten (PSDH1), 20 Minuten (PSDR1) und einer Stunde (PSDS1). Allen drei Verbindungen gemeinsam ist das Entstehen eines intermediären neuen Maximums geringer Intensität, das um etwa 100 nm bathochrom verschoben ist. Das Harnstoffsystem weist außerdem ein weiteres intermediäres Maximum bei 614 nm auf. Diese Maxima können (laut früherer Untersuchungen) durch Oxidation entstandenen chinoiden Strukturen zugeordnet werden, deren Lebensdauer (im Sekundenbereich) zu kurz für eine NMR-Charakterisierung ist. PSDR1 wurde außerdem bei höheren Konzentrationen (10-4 und 10-3 mol/L) mit einer Quecksilberlampe mit Pyrex-Filter (lambda > 300 nm) belichtet. Dabei wird, wie erwartet, eine Verbreiterung der NMR-Signale beobachtet. Es bildet sich zunächst cis-Stilben. Außerdem läßt sich bei 4.3 ppm ein Signal beobachten, das von inter- oder intramolekular gebildeten Methinprotonen herrührt. Auch wenn laut MOPAC- und Kraftfeldrechnung die Doppelbindungen ungünstig für eine [pi2s + pi2s]-Cyclodimerisierung zueinander stehen, kann im photochemisch angeregten Zustand eine Geometrie vorherrschen, die die intramolekulare Kopf-Kopf-Cyclobutanbildung ermöglicht. Die massenspektrometrischen Untersuchungen der Belichtungsprodukte (FD, ESI, MALDI-TOF) zeigen als höchste Masse lediglich das Monomer. Allerdings kann dadurch nicht auf eine rein intramolekulare Reaktion geschlossen werden. Die fortschreitende statistische CC-Verknüpfung kann schnell zu vernetzten Nanopartikeln führen, die im Massenspektrometer nicht fliegen. Die NMR-Spektren der mit zunehmender Vernetzung immer schlechter löslich werdenden Teilchen belegen die Oligomerisierung.

Statistical mechanics of protein complexed and condensed DNA

In this thesis I treat various biophysical questions arising in the context of complexed / ”protein-packed” DNA and DNA in confined geometries (like in viruses or toroidal DNA condensates). Using diverse theoretical methods I consider the statistical mechanics as well as the dynamics of DNA under these conditions. In the first part of the thesis (chapter 2) I derive for the first time the single molecule ”equation of state”, i.e. the force-extension relation of a looped DNA (Eq. 2.94) by using the path integral formalism. Generalizing these results I show that the presence of elastic substructures like loops or deflections caused by anchoring boundary conditions (e.g. at the AFM tip or the mica substrate) gives rise to a significant renormalization of the apparent persistence length as extracted from single molecule experiments (Eqs. 2.39 and 2.98). As I show the experimentally observed apparent persistence length reduction by a factor of 10 or more is naturally explained by this theory. In chapter 3 I theoretically consider the thermal motion of nucleosomes along a DNA template. After an extensive analysis of available experimental data and theoretical modelling of two possible mechanisms I conclude that the ”corkscrew-motion” mechanism most consistently explains this biologically important process. In chapter 4 I demonstrate that DNA-spools (architectures in which DNA circumferentially winds on a cylindrical surface, or onto itself) show a remarkable ”kinetic inertness” that protects them from tension-induced disruption on experimentally and biologically relevant timescales (cf. Fig. 4.1 and Eq. 4.18). I show that the underlying model establishes a connection between the seemingly unrelated and previously unexplained force peaks in single molecule nucleosome and DNA-toroid stretching experiments. Finally in chapter 5 I show that toroidally confined DNA (found in viruses, DNAcondensates or sperm chromatin) undergoes a transition to a twisted, highly entangled state provided that the aspect ratio of the underlying torus crosses a certain critical value (cf. Eq. 5.6 and the phase diagram in Fig. 5.4). The presented mechanism could rationalize several experimental mysteries, ranging from entangled and supercoiled toroids released from virus capsids to the unexpectedly short cholesteric pitch in the (toroidaly wound) sperm chromatin. I propose that the ”topological encapsulation” resulting from our model may have some practical implications for the gene-therapeutic DNA delivery process.

Climate signatures in corals of the tropical-temperate transition zone (Late Miocene, Crete/Greece)

The present study describes a Late Miocene (early Tortonian - early Messinian) transitional carbonate system that combines elements of tropical and cool-water carbonate systems (Irakleion Basin, island of Crete, Greece). As documented by stratal geometries, the submarine topography of the basin was controlled by tilting blocks. Coral reefs formed by Porites and Tarbellastrea occurred in a narrow clastic coastal belt along a „central Cretan landmass“, and steep escarpments formed by faulting. Extensive covers of level-bottom communities existed in a low-energy environment on the gentle dip-slope ramps of the blocks that show the widest geographical distribution within the basin. Consistent patterns of landward and basinward shift of coastal onlap in all outcrop studies reveal an overriding control of 3rd and 4th order sea level changes on sediment dynamics and facies distributions over block movements. An increasingly dry climate and the complex submarine topography of the fault block mosaic kept sediment and nutrient discharge at a minimum. The skeletal limestone facies therefore reflects oligotrophic conditions and a sea surface temperature (SST) near the lower threshold temperature of coral reefs in a climatic position transitional between the tropical coral reef belt and the temperate zone. Stable isotope records (δ18O, δ13C) from massiv, exceptionally preserved Late Miocene aragonite coral skeletons reflect seasonal changes in sea surface temperature and symbiont autotrophy. Spectral analysis of a 69 years coral δ18O record reveals significant variance at interannual time scales (5-6 years) that matches the present-day eastern Mediterranean climate variability controlled by the Arctic Oscillation/North Atlantic Oscillation (AO/NAO), the Northern Hemisphere’s dominant mode of atmospheric variability. Supported by simulations with a complex atmospheric general circulation model coupled to a mixed-layer ocean model, it is suggested, that climate dynamics in the eastern Mediterranean and central Europe reflect atmospheric variability related to the Icelandic Low 10 million years ago. Usually, Miocene corals are transformed in calcite spar in geological time and isotope values are reset by diagenetic alteration. It is demonstrated that the relicts of growth bands represent an intriguing source of information for the growth conditions of fossil corals. Recrystallized growth bands were measured systematically in massive Porites from Crete. The Late Miocene corals were growing slowly with 2-4 mm/yr, compatible with present-day Porites from high latitude reefs, a relationship that fits the position of Crete at the margin of the Miocene tropical reef belt. Over Late Miocene time (Tortonian - early Messinian) growth rates remained remarkably constant, and if the modern growth temperature relationship for massive Porites applies to the Neogene, minimum (winter) SST did not exceed 19-21°C.

A LES study of a modified Ahmed body geometry

A numerical study using Large Eddy Simulation Coherent Structure Model (LES-CSM), of the flow around a simplified Ahmed body, has been done in this work of thesis. The models used are two salient geometries from the experimental investigation performed in [1], and consist, in particular, in two notch-back body geometries. Six simulation are carried out in total, changing Reynolds number and back-light angle of the model’s rear part. The Reynolds numbers used, based on the height of the models and the free stream velocity, are Re = 10000, Re = 30000 and Re = 50000. The back-light angles of the slanted surface with respect to the horizontal roof surface, that characterizes the vehicle, are taken as B = 31.8◦ and B = 42◦ respectively. The experimental results in [1] have shown that, depending on the parameter B, asymmetric and symmetric averaged flow over the back-light and in the wake for a symmetric geometry can be observed. The aims of the present work of master thesis are principally two. The first aim is to investigate and confirm the influence of the parameter B on the presence of the asymmetry of the averaged flow, and confirm the features described in the experimental results. The second important aspect is to investigate and observe the influence of the second variable, the Reynolds number, in the developing of the asymmetric flow itself. The results have shown the presence of the mentioned asymmetry as well as an influence of the Reynolds number on it.

Synthesis and characterization of new discotic polycyclic aromatic hydrocarbons and related pyrolytic nanostructures

Diskotische Hexa-peri-hexabenzocoronene (HBC) als molekulare, definierte graphitische Substrukturen sind bereits seit langem Gegenstand von Untersuchungen zu der Delokalisierung von π-Elektronen. In dieser Arbeit wurden zusätzlich Platin-Komplexe in das periphere Substitutionsmuster von HBC eingeführt. Dies führte zu einer Verbesserung der Emission von dem angeregten Triplett-Zustand in den Singulett-Grundzustand mit einer zusätzlichen Verlängerung der Lebensdauer des angeregten Zustandes. Zusätzlich erlaubte diese Konfiguration ein schnelles Intersystem-Crossing mittels einer verstärkten Spin-Orbit Kopplung, die sowohl bei tiefen Temperaturen, als auch bei Raumtemperatur exklusiv zu Phosphoreszenz (T1→S0) führte. Das Verständniss über solche Prozesse ist auch essentiell für die Entwicklung verbesserter opto-elektronischer Bauteile. Die Erstellung von exakt definierten molekularen Strukturen, die speziell für spezifische Interaktionen hergestellt wurden, machten eine Inkorporation von hydrophoben-hydrophilen, wasserstoffverbrückten oder elektrostatischen funktionalisierten Einheiten notwendig, um damit den supramolekularen Aufbau zu kontrollieren. Mit Imidazolium-Salzen funktionalisierte HBC Derivate wurden zu diesem Zwecke hergestellt. Eine interessante Eigenschaft dieser Moleküle ist ihre Amphiphilie. Dies gestattete die Untersuchung ihrer Eigenschaften in einem polaren Solvens und sowohl der Prozessierbarkeit als auch der Faserbildung auf Siliziumoxid-Trägern. Abhängig vom Lösungsmittel und der gewählten Konditionen konnten hochkristalline Fasern erhalten werden. Durch eine Substitution der HBCs mit langen, sterisch anspruchsvollen Seitenketten, konnte durch eine geeignete Prozessierung eine homöotrope Ausrichtung auf Substraten erreicht werden, was dieses Material interessant für photovoltaische Applikationen macht. Neuartige Polyphenylen-Metall-Komplexe mit diskotischen, linearen und dendritischen Geometrien wurden mittels einer einfachen Reaktion zwischen Co2(CO)8 und Ethinyl-Funktionalitäten in Dichlormethan hergestellt. Nach der Pyrolyse dieser Komplexe ergaben sich unterschiedliche Kohlenstoff-Nanopartikel, inklusive Nanoröhren, graphitischen Nanostäben und Kohlenstoff/Metall Hybrid Komplexe, die durch Elektronenmikroskopie untersucht wurden. Die resultierenden Strukturen waren dabei abhängig von der Zusammensetzung und Struktur der Ausgangssubstanzen. Anhand dieser Resultate ergeben sich diverse Möglichkeiten, um den Mechanismus, der zur Herstellung graphitischer Nanopartikel führt, besser zu verstehen.

Analog Signal Acquisition and Conditioning for Near-Field Capacitive Communication and Active Combined EEG-EIT Monitoring

The work of the present thesis is focused on the implementation of microelectronic voltage sensing devices, with the purpose of transmitting and extracting analog information between devices of different nature at short distances or upon contact. Initally, chip-to-chip communication has been studied, and circuitry for 3D capacitive coupling has been implemented. Such circuits allow the communication between dies fabricated in different technologies. Due to their novelty, they are not standardized and currently not supported by standard CAD tools. In order to overcome such burden, a novel approach for the characterization of such communicating links has been proposed. This results in shorter design times and increased accuracy. Communication between an integrated circuit (IC) and a probe card has been extensively studied as well. Today wafer probing is a costly test procedure with many drawbacks, which could be overcome by a different communication approach such as capacitive coupling. For this reason wireless wafer probing has been investigated as an alternative approach to standard on-contact wafer probing. Interfaces between integrated circuits and biological systems have also been investigated. Active electrodes for simultaneous electroencephalography (EEG) and electrical impedance tomography (EIT) have been implemented for the first time in a 0.35 um process. Number of wires has been minimized by sharing the analog outputs and supply on a single wire, thus implementing electrodes that require only 4 wires for their operation. Minimization of wires reduces the cable weight and thus limits the patient's discomfort. The physical channel for communication between an IC and a biological medium is represented by the electrode itself. As this is a very crucial point for biopotential acquisitions, large efforts have been carried in order to investigate the different electrode technologies and geometries and an electromagnetic model is presented in order to characterize the properties of the electrode to skin interface.

Continuos Flow Single Cell Separation into Open Microwell Arrays

A novel design based on electric field-free open microwell arrays for the automated continuous-flow sorting of single or small clusters of cells is presented. The main feature of the proposed device is the parallel analysis of cell-cell and cell-particle interactions in each microwell of the array. High throughput sample recovery with a fast and separate transfer from the microsites to standard microtiter plates is also possible thanks to the flexible printed circuit board technology which permits to produce cost effective large area arrays featuring geometries compatible with laboratory equipment. The particle isolation is performed via negative dielectrophoretic forces which convey the particles’ into the microwells. Particles such as cells and beads flow in electrically active microchannels on whose substrate the electrodes are patterned. The introduction of particles within the microwells is automatically performed by generating the required feedback signal by a microscope-based optical counting and detection routine. In order to isolate a controlled number of particles we created two particular configurations of the electric field within the structure. The first one permits their isolation whereas the second one creates a net force which repels the particles from the microwell entrance. To increase the parallelism at which the cell-isolation function is implemented, a new technique based on coplanar electrodes to detect particle presence was implemented. A lock-in amplifying scheme was used to monitor the impedance of the channel perturbed by flowing particles in high-conductivity suspension mediums. The impedance measurement module was also combined with the dielectrophoretic focusing stage situated upstream of the measurement stage, to limit the measured signal amplitude dispersion due to the particles position variation within the microchannel. In conclusion, the designed system complies with the initial specifications making it suitable for cellomics and biotechnology applications.

Foliation boudinage

In this thesis foliation boudinage and related structures have been studied based on field observations and numerical modeling. Foliation boudinage occurs in foliated rocks independent of lithology contrast. The developing structures are called ‘Foliation boudinage structures (FBSs)’ and show evidence for both ductile and brittle deformation. They are recognized in rocks by perturbations in monotonous foliation adjacent to a central discontinuity, mostly filled with vein material. Foliation boudinage structures have been studied in the Çine Massif in SW-Turkey and the Furka Pass-Urseren Zone in central Switzerland. Four common types have been distinguished in the field, named after vein geometries in their boudin necks in sections normal to the boudin axis: lozenge-, crescent-, X- and double crescent- type FBSs. Lozengetype FBSs are symmetric and characterized by lozenge-shaped veins in their boudin neck with two cusps facing opposite sides. A symmetrical pair of flanking folds occurs on the two sides of the vein. Crescent-type FBSs are asymmetric with a single smoothly curved vein in the boudin neck, with vein contacts facing to one side. X- and double crescent- type FBSs are asymmetric. The geometry of the neck veins resembles that of cuspate-lobate structures. The geometry of flanking structures is related to the shape of the veins. The veins are mostly filled with massive quartz in large single crystals, commonly associated with tourmaline, feldspar and biotite and in some cases with chlorite. The dominance of large facetted single quartz crystals and spherulitic chlorite in the veins suggest that the minerals grew into open fluidfilled space. FLAC experiments show that fracture propagation during ductile deformation strongly influences the geometry of developing veins. The cusps of the veins are better developed in the case of propagating fractures. The shape of the boudin neck veins in foliation boudinage depends on the initial orientation and shape of the fracture, the propagation behaviour of the fracture, the geometry of bulk flow, and the stage at which mineral filling takes place. A two dimensional discrete element model was used to study the progressive development of foliation boudinage structures and the behavior of visco-elastic material deformed under pure shear conditions. Discrete elements are defined by particles that are connected by visco-elastic springs. Springs can break. A number of simulations was Abstract vii performed to investigate the effect of material properties (Young’s modulus, viscosity and breaking strength) and anisotropy on the developing structures. The models show the development of boudinage in single layers, multilayers and in anisotropic materials with random mica distribution. During progressive deformation different types of fractures develop from mode I, mode II to the combination of both. Voids develop along extension fractures, at intersections of conjugate shear fractures and in small pull-apart structures along shear fractures. These patterns look similar to the natural examples. Fractures are more localized in the models where the elastic constants are low and the competence contrast is high between the layers. They propagate through layers where the constants are high and the competence contrast is relatively low. Flow localize around these fractures and voids. The patterns similar to symmetric boudinage structures and extensional neck veins (e.g. lozenge type) more commonly develop in the models with lower elastic constants and anisotropy. The patterns similar to asymmetric foliation boudinage structures (e.g. X-type) develop associated with shear fractures in the models where elastic constants and anisotropy of the materials are relatively high. In these models boudin neck veins form commonly at pull-aparts along the shear fractures and at the intersection of fractures.

Investigation on laser shock peening capability by FE simulation

Laser shock peening is a technique similar to shot peening that imparts compressive residual stresses in materials for improving fatigue resistance. The ability to use a high energy laser pulse to generate shock waves, inducing a compressive residual stress field in metallic materials, has applications in multiple fields such as turbo-machinery, airframe structures, and medical appliances. The transient nature of the LSP phenomenon and the high rate of the laser's dynamic make real time in-situ measurement of laser/material interaction very challenging. For this reason and for the high cost of the experimental tests, reliable analytical methods for predicting detailed effects of LSP are needed to understand the potential of the process. Aim of this work has been the prediction of residual stress field after Laser Peening process by means of Finite Element Modeling. The work has been carried out in the Stress Methods department of Airbus Operations GmbH (Hamburg) and it includes investigation on compressive residual stresses induced by Laser Shock Peening, study on mesh sensitivity, optimization and tuning of the model by using physical and numerical parameters, validation of the model by comparing it with experimental results. The model has been realized with Abaqus/Explicit commercial software starting from considerations done on previous works. FE analyses are “Mesh Sensitive”: by increasing the number of elements and by decreasing their size, the software is able to probe even the details of the real phenomenon. However, these details, could be only an amplification of real phenomenon. For this reason it was necessary to optimize the mesh elements' size and number. A new model has been created with a more fine mesh in the trough thickness direction because it is the most involved in the process deformations. This increment of the global number of elements has been paid with an "in plane" size reduction of the elements far from the peened area in order to avoid too high computational costs. Efficiency and stability of the analyses has been improved by using bulk viscosity coefficients, a merely numerical parameter available in Abaqus/Explicit. A plastic rate sensitivity study has been also carried out and a new set of Johnson Cook's model coefficient has been chosen. These investigations led to a more controllable and reliable model, valid even for more complex geometries. Moreover the study about the material properties highlighted a gap of the model about the simulation of the surface conditions. Modeling of the ablative layer employed during the real process has been used to fill this gap. In the real process ablative layer is a super thin sheet of pure aluminum stuck on the masterpiece. In the simulation it has been simply reproduced as a 100µm layer made by a material with a yield point of 10MPa. All those new settings has been applied to a set of analyses made with different geometry models to verify the robustness of the model. The calibration of the model with the experimental results was based on stress and displacement measurements carried out on the surface and in depth as well. The good correlation between the simulation and experimental tests results proved this model to be reliable.

Large-scale coupled-cluster calculations

Coupled-cluster theory provides one of the most successful concepts in electronic-structure theory. This work covers the parallelization of coupled-cluster energies, gradients, and second derivatives and its application to selected large-scale chemical problems, beside the more practical aspects such as the publication and support of the quantum-chemistry package ACES II MAB and the design and development of a computational environment optimized for coupled-cluster calculations. The main objective of this thesis was to extend the range of applicability of coupled-cluster models to larger molecular systems and their properties and therefore to bring large-scale coupled-cluster calculations into day-to-day routine of computational chemistry. A straightforward strategy for the parallelization of CCSD and CCSD(T) energies, gradients, and second derivatives has been outlined and implemented for closed-shell and open-shell references. Starting from the highly efficient serial implementation of the ACES II MAB computer code an adaptation for affordable workstation clusters has been obtained by parallelizing the most time-consuming steps of the algorithms. Benchmark calculations for systems with up to 1300 basis functions and the presented applications show that the resulting algorithm for energies, gradients and second derivatives at the CCSD and CCSD(T) level of theory exhibits good scaling with the number of processors and substantially extends the range of applicability. Within the framework of the ’High accuracy Extrapolated Ab initio Thermochemistry’ (HEAT) protocols effects of increased basis-set size and higher excitations in the coupled- cluster expansion were investigated. The HEAT scheme was generalized for molecules containing second-row atoms in the case of vinyl chloride. This allowed the different experimental reported values to be discriminated. In the case of the benzene molecule it was shown that even for molecules of this size chemical accuracy can be achieved. Near-quantitative agreement with experiment (about 2 ppm deviation) for the prediction of fluorine-19 nuclear magnetic shielding constants can be achieved by employing the CCSD(T) model together with large basis sets at accurate equilibrium geometries if vibrational averaging and temperature corrections via second-order vibrational perturbation theory are considered. Applying a very similar level of theory for the calculation of the carbon-13 NMR chemical shifts of benzene resulted in quantitative agreement with experimental gas-phase data. The NMR chemical shift study for the bridgehead 1-adamantyl cation at the CCSD(T) level resolved earlier discrepancies of lower-level theoretical treatment. The equilibrium structure of diacetylene has been determined based on the combination of experimental rotational constants of thirteen isotopic species and zero-point vibrational corrections calculated at various quantum-chemical levels. These empirical equilibrium structures agree to within 0.1 pm irrespective of the theoretical level employed. High-level quantum-chemical calculations on the hyperfine structure parameters of the cyanopolyynes were found to be in excellent agreement with experiment. Finally, the theoretically most accurate determination of the molecular equilibrium structure of ferrocene to date is presented.

Carbonate conical mounds of the eastern Anti-Atlas(Morocco) and their relationship with potential analogues on Mars

Longstanding debates concerning the origin of the Kess Kess Emsian carbonate mounds exposed at Hamar Laghdad Ridge (eastern Anti-Atlas, Morocco) centre around the processes that induced precipitation of carbonate mud and the preservation of steep morphologies. Although in the last years an origin related to hydrothermalism seemed to be more likely, to date the Kess Kess are still considered controversial vent deposits. This study combines in updated research review information from previous work and new detailed field observations coupled with new analytical results to define a consistent framework and some new insight of current knowledge about the origin of these mounds. We obtain a complete minero-petrographic and palaeobiological data set and a detailed geochemical characterization of the different lithologies and facies of the Hamar Laghdad stratigraphic succession, including mounds, and we compared the results with the data from Maïder Basin mounds (Anti-Atlas, Morocco). Our data support the hydrothermal model proposed for the genesis and development of the Kess Kess mounds. The mechanisms linked to the mounds formation and growth are discussed in the light of the new finding of fluid-sediment interaction within a scenario driven by late magmatic fluids circulation. Conical mounds and other fluids related morphologies were also reported from Crommelin crater area (Arabia Terra, Mars). These mounds consist in meter-sized conical buildups hosted in the Equatorial Layered Deposits (ELDs) deposed during a regional groundwater fluid upwelling. Geometries and geological conditions that might have controlled the development of such morphologies were discussed. According to our data the morphological and stratigraphical characteristics of Crommelin area mounds are most consistent with a formation by fluids advection. Then we compare terrestrial and Martian data and examine the geological settings of hydrothermal mound occurrences on Earth in order to describe potential target areas for hydrothermal structures on Mars.

Solid-state NMR investigation of phosphonic acid based proton conducting materials

In this work, new promising proton conducting fuel cell membrane materials were characterized in terms of their structure and dynamic properties using solid-state nuclear magnetic resonance (NMR) spectroscopy and X-ray diffraction. Structurally different, phosphonic acid (PA) containing materials were systematically evaluated for possible high-temperature operation (e.g. at T>100°C). Notably, 1H, 2H and 31P magic angle spinning (MAS) NMR provided insight into local connectivities and dynamics of the hydrogen bonded network, while packing arrangements were identified by means of heteronuclear dipolar recoupling techniques.rnThe first part of this work introduced rather crystalline, low molecular weight ionomers for proton conducting membranes, where six different geometries such as line, triangle, screw, tetrahedron, square and hexagon, were investigated. The hexagon was identified as the most promising geometry with high-temperature bulk proton conductivities in the range of 10-3 Scm-1 at a relative humidity of 50%. However, 2H NMR and TGA-MS data suggest that the bulk proton transport is mainly due to the presence of crystal water. Single crystal X-ray data revealed that in the tetrahedron phosphonic acids form tetrameric clusters isolating the mobile protons while the phosphonic acids in the hexagon form zigzag-type pathways through the sample.rnThe second part of this work demonstrates how acid-base pairing and the choice of appropriate spacers may influence proton conduction. Different ratios of statistical copolymers of poly (vinylphosphonic acid) and poly (4-vinylpyridine) were measured to derive information about the local structure and chemical changes. Though anhydrous proton conductivities of all statistical copolymers are rather poor, the conductivity increases to 10-2 S cm-1 when exposing the sample to relative humidity of 80%. In contrast to PVPA, anhydride formation of phosphonic acids in the copolymer is not reversible even when exposing the sample to a relative humidity of 100%.rnIn addition, the influence of both spacers and degree of backbone crystallinity on bulk proton conductivity was investigated. Unlike in systems such as poly benzimidazole (PBI), spacers were inserted between the protogenic groups along the backbone. It was found that dilution of the protogenic groups decreases the conductivity, but compared to PVPA, similar apparent activation energies for local motions were obtained from both variable temperature 1H NMR and impedance spectroscopy data. These observations suggest the formation of phosphonic acid clusters with high degrees of local proton motion, where only a fraction of motions contribute to the observable bulk proton conductivity. Additionally, it was shown that gradual changes of the spacer length lead to different morphologies.rnIn summary, applying advanced solid-state NMR and X-ray analysis, structural and dynamic phenomena in proton conducting materials were identified on a molecular level. The results were discussed with respect to different proton conduction mechanisms and may contribute to a more rational design or improvement of proton conducting membranes.rn

Numerical methods for the dispersion analysis of Guided Waves

The use of guided ultrasonic waves (GUW) has increased considerably in the fields of non-destructive (NDE) testing and structural health monitoring (SHM) due to their ability to perform long range inspections, to probe hidden areas as well as to provide a complete monitoring of the entire waveguide. Guided waves can be fully exploited only once their dispersive properties are known for the given waveguide. In this context, well stated analytical and numerical methods are represented by the Matrix family methods and the Semi Analytical Finite Element (SAFE) methods. However, while the former are limited to simple geometries of finite or infinite extent, the latter can model arbitrary cross-section waveguides of finite domain only. This thesis is aimed at developing three different numerical methods for modelling wave propagation in complex translational invariant systems. First, a classical SAFE formulation for viscoelastic waveguides is extended to account for a three dimensional translational invariant static prestress state. The effect of prestress, residual stress and applied loads on the dispersion properties of the guided waves is shown. Next, a two-and-a-half Boundary Element Method (2.5D BEM) for the dispersion analysis of damped guided waves in waveguides and cavities of arbitrary cross-section is proposed. The attenuation dispersive spectrum due to material damping and geometrical spreading of cavities with arbitrary shape is shown for the first time. Finally, a coupled SAFE-2.5D BEM framework is developed to study the dispersion characteristics of waves in viscoelastic waveguides of arbitrary geometry embedded in infinite solid or liquid media. Dispersion of leaky and non-leaky guided waves in terms of speed and attenuation, as well as the radiated wavefields, can be computed. The results obtained in this thesis can be helpful for the design of both actuation and sensing systems in practical application, as well as to tune experimental setup.