TlBr raw material purification, crystal growth, annealing, detector fabrication and characterisation for gamma-ray detector applications

The research reported in this thesis dealt with single crystals of thallium bromide grown for gamma-ray detector applications. The crystals were used to fabricate room temperature gamma-ray detectors. Routinely produced TlBr detectors often are poor quality. Therefore, this study concentrated on developing the manufacturing processes for TlBr detectors and methods of characterisation that can be used for optimisation of TlBr purity and crystal quality. The processes under concern were TlBr raw material purification, crystal growth, annealing and detector fabrication. The study focused on single crystals of TlBr grown from material purified by a hydrothermal recrystallisation method. In addition, hydrothermal conditions for synthesis, recrystallisation, crystal growth and annealing of TlBr crystals were examined. The final manufacturing process presented in this thesis deals with TlBr material purified by the Bridgman method. Then, material is hydrothermally recrystallised in pure water. A travelling molten zone (TMZ) method is used for additional purification of the recrystallised product and then for the final crystal growth. Subsequent processing is similar to that described in the literature. In this thesis, literature on improving quality of TlBr material/crystal and detector performance is reviewed. Aging aspects as well as the influence of different factors (temperature, time, electrode material and so on) on detector stability are considered and examined. The results of the process development are summarised and discussed. This thesis shows the considerable improvement in the charge carrier properties of a detector due to additional purification by hydrothermal recrystallisation. As an example, a thick (4 mm) TlBr detector produced by the process was fabricated and found to operate successfully in gamma-ray detection, confirming the validity of the proposed purification and technological steps. However, for the complete improvement of detector performance, further developments in crystal growth are required. The detector manufacturing process was optimized by characterisation of material and crystals using methods such as X-ray diffraction (XRD), polarisation microscopy, high-resolution inductively coupled plasma mass (HR-ICPM), Fourier transform infrared (FTIR), ultraviolet and visual (UV-Vis) spectroscopy, field emission scanning electron microscope (FESEM) and energy-dispersive X-ray spectroscopy (EDS), current-voltage (I-V) and capacity voltage (CV) characterisation, and photoconductivity, as well direct detector examination.

Cavity-enhanced laser spectroscopic studies of vibrational overtones of acetylene

This thesis contains five experimental spectroscopic studies that probe the vibration-rotation energy level structure of acetylene and some of its isotopologues. The emphasis is on the development of laser spectroscopic methods for high-resolution molecular spectroscopy. Three of the experiments use cavity ringdown spectroscopy. One is a standard setup that employs a non-frequency stabilised continuous wave laser as a source. In the other two experiments, the same laser is actively frequency stabilised to the ringdown cavity. This development allows for increased repetition rate of the experimental signal and thus the spectroscopic sensitivity of the method is improved. These setups are applied to the recording of several vibration-rotation overtone bands of both H(12)C(12)CH and H(13)C(13)CH. An intra-cavity laser absorption spectroscopy setup that uses a commercial continuous wave ring laser and a Fourier transform interferometer is presented. The configuration of the laser is found to be sub-optimal for high-sensitivity work but the spectroscopic results are good and show the viability of this type of approach. Several ro-vibrational bands of carbon-13 substituted acetylenes are recorded and analysed. Compared with earlier work, the signal-to-noise ratio of a laser-induced dispersed infrared fluorescence experiment is enhanced by more than one order of magnitude by exploiting the geometric characteristics of the setup. The higher sensitivity of the spectrometer leads to the observation of two new symmetric vibrational states of H(12)C(12)CH. The precision of the spectroscopic parameters of some previously published symmetric states is also improved. An interesting collisional energy transfer process is observed for the excited vibrational states and this phenomenon is explained by a simple step-down model.

Structural transitions in (La,Ln)2CuO4 and La2(Cu,Ni)O4 systems

Solid solutions of the formula La2−xLnxCuO4 (Ln = Pr, Nd) possess the orthorhombic structure of La2CuO4 for small values of x and transform to the tetragonal Nd2CuO4 structure at a critical value of x. At the critical composition, there is an abrupt change in specific volume as well as the Image ratio. The material exhibits temperature-independent electrical resistivity below the critical value x and semiconducting behaviour above it. The specific volume and Image ratio smoothly decrease with increase in x in the La2Cu1−xNixO4 system, although the solid solution possess the tetragonal K2NiF4 structure when x>0.1. Compositions with x>0.1 exhibit a gradual semiconductor metal transition similar to that of La2NiO4, the transition temperature decreasing with increasing

Plasmatic Transformation

The session examines the role of the metaphysical and physical in art and animation and how this relates to natural spaces. Soviet Russian film director and theorist Sergei Eisenstein saw animation as possessing an ability called “plasmaticity”, the capacity for a being to assume any conceivable form dynamically. He saw each being as “primordial protoplasm, not yet possessing a ‘stable’ form, but capable of assuming any form” (Eisenstein 1989, 21). He was enamoured by the capacity of animation to transform and be liberated, of being able to escape from a fixed and static identity—to embody a "rejection of the once-­‐and-­‐forever allotted form" in which we are held (Eisenstein 1989, 21). Czech Surrealist animator Jan Švankmajer uses a metaphysical approach based on a belief in animism to art and animation. He believes that objects possess a conscious life or spirit, he says ‘Objects conceal within themselves the events they’ve witnessed. I don’t actually animate objects. I coerce their inner life out of them.’ (Švankmajer in Imre 2009, 214) In this animistic world there are no boundaries or rules, no physical or conceptual restrictions; anything is possible, with inanimate objects and places able to become animate and transact in a conscious relationship with humans and each other. This session invites artists, animators and theorists to discuss their conceptions and approaches to using visuals to promote and provoke transformation.

Deriving structural information from non-coding ribonucleic acids by mass spectrometry

The purpose of this study is to describe the development of application of mass spectrometry for the structural analyses of non-coding ribonucleic acids during past decade. Mass spectrometric methods are compared of traditional gel electrophoretic methods, the characteristics of performance of mass spectrometric, analyses are studied and the future trends of mass spectrometry of ribonucleic acids are discussed. Non-coding ribonucleic acids are short polymeric biomolecules which are not translated to proteins, but which may affect the gene expression in all organisms. Regulatory ribonucleic acids act through transient interactions with key molecules in signal transduction pathways. Interactions are mediated through specific secondary and tertiary structures. Posttranscriptional modifications in the structures of molecules may introduce new properties to the organism, such as adaptation to environmental changes or development of resistance to antibiotics. In the scope of this study, the structural studies include i) determination of the sequence of nucleobases in the polymer chain, ii) characterisation and localisation of posttranscriptional modifications in nucleobases and in the backbone structure, iii) identification of ribonucleic acid-binding molecules and iv) probing of higher order structures in the ribonucleic acid molecule. Bacteria, archaea, viruses and HeLa cancer cells have been used as target organisms. Synthesised ribonucleic acids consisting of structural regions of interest have been frequently used. Electrospray ionisation (ESI) and matrix-assisted laser desorption ionisation (MALDI) have been used for ionisation of ribonucleic analytes. Ammonium acetate and 2-propanol are common solvents for ESI. Trihydroxyacetophenone is the optimal MALDI matrix for ionisation of ribonucleic acids and peptides. Ammonium salts are used in ESI buffers and MALDI matrices as additives to remove cation adducts. Reverse phase high performance liquid chromatography has been used for desalting and fractionation of analytes either off-line of on-line, coupled with ESI source. Triethylamine and triethylammonium bicarbonate are used as ion pair reagents almost exclusively. Fourier transform ion cyclotron resonance analyser using ESI coupled with liquid chromatography is the platform of choice for all forms of structural analyses. Time-of-flight (TOF) analyser using MALDI may offer sensitive, easy-to-use and economical solution for simple sequencing of longer oligonucleotides and analyses of analyte mixtures without prior fractionation. Special analysis software is used for computer-aided interpretation of mass spectra. With mass spectrometry, sequences of 20-30 nucleotides of length may be determined unambiguously. Sequencing may be applied to quality control of short synthetic oligomers for analytical purposes. Sequencing in conjunction with other structural studies enables accurate localisation and characterisation of posttranscriptional modifications and identification of nucleobases and amino acids at the sites of interaction. High throughput screening methods for RNA-binding ligands have been developed. Probing of the higher order structures has provided supportive data for computer-generated three dimensional models of viral pseudoknots. In conclusion. mass spectrometric methods are well suited for structural analyses of small species of ribonucleic acids, such as short non-coding ribonucleic acids in the molecular size region of 20-30 nucleotides. Structural information not attainable with other methods of analyses, such as nuclear magnetic resonance and X-ray crystallography, may be obtained with the use of mass spectrometry. Sequencing may be applied to quality control of short synthetic oligomers for analytical purposes. Ligand screening may be used in the search of possible new therapeutic agents. Demanding assay design and challenging interpretation of data requires multidisclipinary knowledge. The implement of mass spectrometry to structural studies of ribonucleic acids is probably most efficiently conducted in specialist groups consisting of researchers from various fields of science.

The Trans-Pacific partnership protects old companies at the expense of the new

Under this trade agreement, intellectual property will be transformed into a means of protecting the investments of multinational companies in culture, advertising, and medicine, writes Matthew Rimmer. The Trans-Pacific Partnership (TPP) is a blockbuster trade deal, which will transform the intellectual property of the Pacific Rim. The Australian Prime Minister Malcolm Turnbull has argued the trade agreement is a "gigantic foundation stone" for the country's future prosperity. Nonetheless, though the final text remains unreleased, it's clear from what we do know that the Intellectual Property Chapter is set to protect legacy intellectual property industries - rather than support disruptive technologies and dynamic innovation.

On the Rademacher maximal function

Tools known as maximal functions are frequently used in harmonic analysis when studying local behaviour of functions. Typically they measure the suprema of local averages of non-negative functions. It is essential that the size (more precisely, the L^p-norm) of the maximal function is comparable to the size of the original function. When dealing with families of operators between Banach spaces we are often forced to replace the uniform bound with the larger R-bound. Hence such a replacement is also needed in the maximal function for functions taking values in spaces of operators. More specifically, the suprema of norms of local averages (i.e. their uniform bound in the operator norm) has to be replaced by their R-bound. This procedure gives us the Rademacher maximal function, which was introduced by Hytönen, McIntosh and Portal in order to prove a certain vector-valued Carleson's embedding theorem. They noticed that the sizes of an operator-valued function and its Rademacher maximal function are comparable for many common range spaces, but not for all. Certain requirements on the type and cotype of the spaces involved are necessary for this comparability, henceforth referred to as the “RMF-property”. It was shown, that other objects and parameters appearing in the definition, such as the domain of functions and the exponent p of the norm, make no difference to this. After a short introduction to randomized norms and geometry in Banach spaces we study the Rademacher maximal function on Euclidean spaces. The requirements on the type and cotype are considered, providing examples of spaces without RMF. L^p-spaces are shown to have RMF not only for p greater or equal to 2 (when it is trivial) but also for 1 < p < 2. A dyadic version of Carleson's embedding theorem is proven for scalar- and operator-valued functions. As the analysis with dyadic cubes can be generalized to filtrations on sigma-finite measure spaces, we consider the Rademacher maximal function in this case as well. It turns out that the RMF-property is independent of the filtration and the underlying measure space and that it is enough to consider very simple ones known as Haar filtrations. Scalar- and operator-valued analogues of Carleson's embedding theorem are also provided. With the RMF-property proven independent of the underlying measure space, we can use probabilistic notions and formulate it for martingales. Following a similar result for UMD-spaces, a weak type inequality is shown to be (necessary and) sufficient for the RMF-property. The RMF-property is also studied using concave functions giving yet another proof of its independence from various parameters.

Algorithms for 13C metabolic flux analysis

The metabolism of an organism consists of a network of biochemical reactions that transform small molecules, or metabolites, into others in order to produce energy and building blocks for essential macromolecules. The goal of metabolic flux analysis is to uncover the rates, or the fluxes, of those biochemical reactions. In a steady state, the sum of the fluxes that produce an internal metabolite is equal to the sum of the fluxes that consume the same molecule. Thus the steady state imposes linear balance constraints to the fluxes. In general, the balance constraints imposed by the steady state are not sufficient to uncover all the fluxes of a metabolic network. The fluxes through cycles and alternative pathways between the same source and target metabolites remain unknown. More information about the fluxes can be obtained from isotopic labelling experiments, where a cell population is fed with labelled nutrients, such as glucose that contains 13C atoms. Labels are then transferred by biochemical reactions to other metabolites. The relative abundances of different labelling patterns in internal metabolites depend on the fluxes of pathways producing them. Thus, the relative abundances of different labelling patterns contain information about the fluxes that cannot be uncovered from the balance constraints derived from the steady state. The field of research that estimates the fluxes utilizing the measured constraints to the relative abundances of different labelling patterns induced by 13C labelled nutrients is called 13C metabolic flux analysis. There exist two approaches of 13C metabolic flux analysis. In the optimization approach, a non-linear optimization task, where candidate fluxes are iteratively generated until they fit to the measured abundances of different labelling patterns, is constructed. In the direct approach, linear balance constraints given by the steady state are augmented with linear constraints derived from the abundances of different labelling patterns of metabolites. Thus, mathematically involved non-linear optimization methods that can get stuck to the local optima can be avoided. On the other hand, the direct approach may require more measurement data than the optimization approach to obtain the same flux information. Furthermore, the optimization framework can easily be applied regardless of the labelling measurement technology and with all network topologies. In this thesis we present a formal computational framework for direct 13C metabolic flux analysis. The aim of our study is to construct as many linear constraints to the fluxes from the 13C labelling measurements using only computational methods that avoid non-linear techniques and are independent from the type of measurement data, the labelling of external nutrients and the topology of the metabolic network. The presented framework is the first representative of the direct approach for 13C metabolic flux analysis that is free from restricting assumptions made about these parameters.In our framework, measurement data is first propagated from the measured metabolites to other metabolites. The propagation is facilitated by the flow analysis of metabolite fragments in the network. Then new linear constraints to the fluxes are derived from the propagated data by applying the techniques of linear algebra.Based on the results of the fragment flow analysis, we also present an experiment planning method that selects sets of metabolites whose relative abundances of different labelling patterns are most useful for 13C metabolic flux analysis. Furthermore, we give computational tools to process raw 13C labelling data produced by tandem mass spectrometry to a form suitable for 13C metabolic flux analysis.

The averaging principle and the diagram technique

Rae and Davidson have found a striking connection between the averaging method generalised by Kruskal and the diagram technique used by the Brussels school in statistical mechanics. They have considered conservative systems whose evolution is governed by the Liouville equation. In this paper we have considered a class of dissipative systems whose evolution is governed not by the Liouville equation but by the last-multiplier equation of Jacobi whose Fourier transform has been shown to be the Hopf equation. The application of the diagram technique to the interaction representation of the Jacobi equation reveals the presence of two kinds of interactions, namely the transition from one mode to another and the persistence of a mode. The first kind occurs in the treatment of conservative systems while the latter type is unique to dissipative fields and is precisely the one that determines the asymptotic Jacobi equation. The dynamical equations of motion equivalent to this limiting Jacobi equation have been shown to be the same as averaged equations.

Time-dependent flows of rotating and stratified fluids in geometries with non-uniform cross-sections

Unsteady rotating and stratified flows in geometries with non-uniform cross-sections are investigated under Oseen approximation using Laplace transform technique. The solutions are obtained in closed form and they reveal that the flow remains oscillatory even after infinitely large time. The existence of inertial waves propagating in both positive and negative directions of the flow is observed. When the Rossby or Froude number is close to a certain infinite set of critical values the blocking and back flow occur and the flow pattern becomes more and more complicated with increasing number of stagnant zones when each critical value is crossed. The analogy that is observed in the solutions for rotating and stratified flows is also discussed.

Block- and strand-multiplexing for fast computation of a class of transforms

The transforms dealt with in this paper are defined in terms of the transform kernels which are Kroneeker products of the two or more component kernels. The signal flow-graph for the computation of such a transform is obtained with the flow-graphs for the component transforms as building blocks.

Towards a Critique of the Concept of the Right to Self-Determination in Africa : A Conceptual Examination and the Cases of Western Sahara, Southern Sudan and Eritrea

This thesis examines the right to self-determination which is a norm used for numerous purposes by multiple actors in the field of international relations, with relatively little clarity or agreement on the actual and potential meaning of the right. In international practice, however, the main focus in applying the right has been in the context of decolonization as set by the United Nations in its early decades. Thus, in Africa the right to self-determination has traditionally implied that the colonial territories, and particularly the populations within these territories, were to constitute the people who were entitled to the right. That is, self-determination by decolonization provided a framework for the construction of independent nation-states in Africa whilst other dimensions of the right remained largely or totally neglected. With the objective of assessing the scope, content, developments and interpretations of the right to self-determination in Africa, particularly with regard to the relevance of the right today, the thesis proceeds on two fundamental hypotheses. The first is that Mervyn Frost s theory of settled norms, among which he lists the right to self-determination, assumes too much. Even if the right to self-determination is a human right belonging to all peoples stipulated, inter alia, in the first Article of the 1966 International Human Rights Covenants, it is a highly politicized and context-bound right instead of being settled and observed in a way that its denial would need special justification. Still, the suggested inconsistency or non-compliance with the norm of self-determination is not intended to prove the uselessness or inappropriateness of the norm, but, on the contrary, to invite and encourage debate on the potential use and coverage of the right to self-determination. The second hypothesis is that within the concept of self-determination there are two normative dimensions. One is to do with the idea and practice of statehood, the nation and collectivity that may decide to conduct itself as an independent state. The other one is to do with self-determination as a human right, as a normative condition, to be enjoyed by people and peoples within states that supersedes state authority. These external and internal dimensions need to be seen as complementary and co-terminous, not as mutually exclusive alternatives. The thesis proceeds on the assumption that the internal dimension of the right, with human rights and democracy at its core, has not been considered as important as the external. In turn, this unbalanced and selective interpretation has managed to put the true normative purpose of the right making the world better and bringing more just polity models into a somewhat peculiar light. The right to self-determination in the African context is assessed through case studies of Western Sahara, Southern Sudan and Eritrea. The study asks what these cases say about the right to self-determination in Africa and what their lessons learnt could contribute to the understanding and relevance of the right in today s Africa. The study demonstrates that even in the context of decolonization, the application of the right to self-determination has been far from the consistent approach supposedly followed by the international community: in many respects similar colonial histories have easily led to rather different destinies. While Eritrea secured internationally recognized right to self-determination in the form of retroactive independence in 1993, international recognition of distinct Western Sahara and Southern Sudan entities is contingent on complex and problematic conditions being satisfied. Overall, it is a considerable challenge for international legality to meet empirical political reality in a meaningful way, so that the universal values attached to the norm of self-determination are not overlooked or compromised but rather reinforced in the process of implementing the right. Consequently, this thesis seeks a more comprehensive understanding of the right to self-determination with particular reference to post-colonial Africa and with an emphasis on the internal, human rights and democracy dimensions of the norm. It is considered that the right to self-determination cannot be perceived only as an inter-state issue as it is also very much an intra-state issue, including the possibility of different sub-state arrangements exercised under the right, for example, in the form of autonomy. At the same time, the option of independent statehood achieved through secession remains a mode of exercising and part of the right to self-determination. But in whatever form or way applied, the right to self-determination, as a normative instrument, should constitute and work as a norm that comprehensively brings more added value in terms of the objectives of human rights and democracy. From a normative perspective, a peoples right should not be allowed to transform and convert itself into a right of states. Finally, in light of the case studies of Western Sahara, Southern Sudan and Eritrea, the thesis suggests that our understanding of the right to self-determination should now reach beyond the post-colonial context in Africa. It appears that both the questions and answers to the most pertinent issues of self-determination in the cases studied must be increasingly sought within the postcolonial African state rather than solely in colonial history. In this vein, the right to self-determination can be seen not only as a tool for creating states but also as a way to transform the state itself from within. Any such genuinely post-colonial approach may imply a judicious reconsideration, adaptation or up-dating of the right and our understanding of it in order to render it meaningful in Africa today.

Ett' varttuisi Suomenmaa : Suomalaisten kasvattaminen kulutusyhteiskuntaan kotimaisissa lyhytelokuvissa 1920-1969

The birth of the Modern Consumer Society in Finnish short films 1920-1969 The main subject of this research is Finnish short films in 1920-1969. These short films were produced by film studios for private enterprises, banks, advisory organizations, communities and the state. The evolution of short films on consumer affairs was greatly influenced by a special tax reduction system that was introduced in 1933 and lasted until 1964. The tax reduction system increased the production volumes of educational short films significantly. This study covers 342 Finnish short films, more than any other study in the field before this. The aim of this research is to examine how short films introduced Finns to modern consumer society. The cinemagoers were an excellent target group for different advisory groups as well as advertisers. Short films were used by organizations and private enterprises from very early on. In the 1920's Finns were still living in rural areas and agriculture was the dominant industry. Consumer society was still in its infancy, and the prevalent attitude to industrially produced goods was that of suspicion. From the cultural and ideological point of view the evolution of trust was one of the first steps towards the birth of the consumer society. Short films were an excellent means for helping to transform public attitudes. During the war period short films were an important means of propaganda. Short films were produced in abundance and shown for big audiences. They guided people how to survive shortages caused by the war. Even though the idea of rationalization was presented in short films somewhat in the 1920's and 1930's it became a national virtue during the war period. The idea of rationalization widened from the industry to households expecially in the late 1940's and the 1950's. New household apparati and the way in which daily chores were taken care of were presented not as luxury consumption but as a way of rationalization and saving money and effort. Banks and the advisory organizations guided the public to save their money for a specific target. Short films were use to help the public to acceps industrial goods and the notions of planning and saving. The ideological change from an agrarian society to consumer society was based on old acricultural ideas and self-sufficiency was evolved into rational and economizing consumerism. This made Finnish consumer society to value durable consumer goods and own homes. The public was also encouraged to consider their own decisions in the national context - especially after the second world war Finland laced capital, and personal savings were strongly presented as a way to help the whole nation. Modern hedonistic values were not dominant in Finland in the1950's and 1960's. Initial traces of modern hedonism can be seen in the films, but they were only marginal paths in the bigger.

Transforming higher education and student engagement through collaborative review to inform educational design

This paper reports on staff perceptions arising from a review process designed to assist staff in making informed decisions regarding educational design, approaches to engage students in learning, and the technology to support engagement in the classroom and across multiple locations and delivery modes. The aim of the review process was to transform the level of student engagement in the business faculty of an Australian university. The process took a collaborative approach through consultation with academic staff involved in the design and delivery of the units under review, and included targeted professional development as necessary. An institutional framework that characterises engagement indicator contexts and their attributes facilitated dialog during the review process. This paper reports on a mixed method study that included a survey of participants, and purposeful interviews to evaluate the effectiveness of the process. Although the study identified factors that hindered implementation and operationalization of review recommendations in some instances, study participants were generally of the view that recommendations would enhance student engagement. It is demonstrated that the bottom-up approach described in this paper is consistent with theoretical frameworks for transformational change in teaching and learning and the adoption of innovations.

Vibration-rotation pattern in acetylene. II. Introduction of Coriolis coupling in the global model and analysis of emission spectra of hot acetylene around 3 mu m

A high temperature source has been developed and coupled to a high resolution Fourier transform spectrometer to record emission spectra of acetylene around 3 mu m up to 1455 K under Doppler limited resolution (0.015 cm(-1)). The nu(3)-ground state (GS) and nu(2)+nu(4)+nu(5)(Sigma(+)(u) and Delta(u))-GS bands and 76 related hot bands, counting e and f parities separately, are assigned using semiautomatic methods based on a global model to reproduce all related vibration-rotation states. Significantly higher J-values than previously reported are observed for 40 known substates while 37 new e or f vibrational substates, up to about 6000 cm(-1), are identified and characterized by vibration-rotation parameters. The 3 811 new or improved data resulting from the analysis are merged into the database presented by Robert et al. [Mol. Phys. 106, 2581 (2008)], now including 15 562 lines accessing vibrational states up to 8600 cm(-1). A global model, updated as compared to the one in the previous paper, allows all lines in the database to be simultaneously fitted, successfully. The updates are discussed taking into account, in particular, the systematic inclusion of Coriolis interaction.