Thermal and exergy analysis for evaluation and optimization of performance of cooling towers for fresh water and seawater

In this study, thermal, exergetic analysis and performance evaluation of seawater and fresh wet cooling tower and the effect of parameters on its performance is investigated. With using of energy and mass balance equations, experimental results, a mathematical model and EES code developed. Due to lack of fresh water, seawater cooling is interesting choice for future of cooling, so the effect of seawater in the range of 1gr/kg to 60gr/kg for salinity on the performance characteristics like air efficiency, water efficiency, output water temperature of cooling tower, flow of the exergy, and the exergy efficiency with comparison with fresh water examined. Decreasing of air efficiency about 3%, increasing of water efficiency about 1.5% are some of these effects. Moreover with formation of fouling the performance of cooling tower decreased about 15% which this phenomena and its effects like increase in output water temperature and tower excess volume has been showed and also accommodate with others work. Also optimization for minimizing cost, maximizing air efficiency, and minimizing exergy destruction has been done, results showed that optimization on minimizing the exergy destruction has been satisfy both minimization of the cost and the maximization of the air efficiency, although it will not necessarily permanent for all inputs and optimizations. Validation of this work is done by comparing computational results and experimental data which showed that the model have a good accuracy.

Analysis of the four wave mixing effect (FWM) in a dispersion decreasing fiber (DDF) for a WDM system

We did a numerical investigation of the propagation of short light pulses in the region of 1.55 mu m and the conversion efficiency (CE) for the four wave mixing generation (FWM) of ordinary and dispersion decreasing fibers for use in wavelength division multiplexing (WDM) systems, Our simulations studies three different profiles, linear, hyperbolic. and constant, One conclude that for all the profiles there is decrease of the conversion efficiency with the increase in the channel separation. The hyperbolic profile present a higher efficiency of around 1000 above in magnitude compared with the others profiles at 0.2 nm of channel separation. We calculate the conversion efficiency versus the fiber length for the three profiles. The conversion efficiency for the hyperbolic profile is higher when compared to the constant and linear profiles. The other interesting point of the hyperbolic profile is that the increase of the CE in the beginning of the fiber does not show my oscillation in the CE value (log eta), which was observed for the constant and linear profiles. For all the profiles there is an increase of the conversion efficiency with the increase of the pump power. The compression factor C-i for the generated FWM signal at omega(3) was measured along the DDF's and the constant profile fibers. One can conclude that with the use of decreasing dispersion profile (DDF) fibers one can have a control of the (CE) conversion efficiency and the compression factor of the four wave mixing (FWM) generation in WDM systems. (c) 2005 Elsevier B.V. All rights reserved.

Comprehensive economic and financial analysis of the enterprise activity: approaches, methods and implementation

This thesis intends to analyse the performance and the efficiency of companies and to identify the key factors that may explain it. A comprehensive analysis based on a set of economic and financial ratios was studied as an instrument which provides information on enterprise performance and its efficiency. It was selected a sample with 15 enterprises: 7 Portuguese and 8 Ukrainian ones, belonging to several industries. Financial and non-financial data was collected for 6 years, during the period of 2009 to 2014. Research questions that guided this work were: Are the enterprises efficient/profitable? What factors influence enterprises’ efficiency/performance? Is there any difference between Ukrainian and Portuguese enterprises’ efficiency/performance, which factors have more influence? Which industrial sector is represented by more efficient/profitable enterprises? The main results showed that in average enterprises were efficient; comparing by states Ukrainian enterprises are more efficient; industries have similar level of efficiency. Among factors that influence ATR positively are fixed and current assets turnover ratios, ROA; negatively influencing are EBITDA margin and liquidity ratio. There is no significant difference between models by country. Concerning profitability, enterprises have low performance level but in comparison of countries Ukrainian enterprises have better profitability in average. Regarding the industry sector, paper industry is the most profitable. Among factors influencing ROA are profit margin, fixed asset turnover ratio, EBITDA margin, Debt to equity ratio and the country. In case of profitability both countries have different models. For Ukrainian enterprises is suggested to pay attention on factors of Short-term debt to total debt, ROA, Interest coverage ratio in order to be more efficient; Profit margin and EBITDA margin to make their performance better. For Portuguese enterprises for improving efficiency the observation and improvement of fixed assets turnover ratio, current assets turnover ratio, Short-term financial debt to total debt, Leverage Ratio, EBITDA margin is suggested; for improving higher profitability track fixed assets turnover ratio, current assets turnover ratio, Debt to equity ratio, Profit margin and Interest coverage ratio is suggested.

NUTRITIONAL AND AMINO ACID ANALYSIS OF RAW, PARTIALLY FERMENTED AND COMPLETELY FERMENTED LOCUST BEAN ( Parkia biglobosa ) SEEDS

The nutritional and amino acid analysis of raw and fermented seeds of Parkia biglobosa were carried out. Parameters investigated include moisture, crude protein, crude fat, ash, crude fibre and mineral contents; and the effect of the degree of fermentation on these parameters was also investigated. The amino acid compositions of all the samples were evaluated and amino acid quality determined by calculating amino acid scores and the predicted protein efficiency ratio (P-PER). Results showed that the proximate composition was significantly affected by fermentation, although there was little difference between the parameters for the partially fermented and completely fermented samples. Based on dry matter percentage, protein content was in the 39.77 – 43.74 % range while crude fibre ranged between 5.55 – 7.42 %. The ash content was lowest in the raw sample (2.34 %), while the fermented samples had ash contents between 4.27 and 8.33 % for the fully fermented and the partially fermented seeds, respectively. The fat content increased from 8.65 % in the raw seed to 24.4 % and 27.6 % for the partially and completely fermented samples, respectively. Results of the amino acid analysis showed that the partially fermented sample had the lowest quantities of all amino acids determined and had lysine as the limiting amino acid, whereas the raw and completely fermented samples had very similar amino acid profile with amino acid scores of 100, indicating that there are no limiting amino acids. All the samples were rich in essential amino acids. The P-PER also showed that the partially fermented sample had the lowest protein efficiency while the raw seed had the highest. Mineral contents generally increased from the raw, through the partially fermented, to the completely fermented seeds and results showed the samples to be good sources of potassium (K), calcium (Ca), manganese (Mn) and copper (Cu) in addition to being complementary sources of other metals. Locust bean seed does not accumulate lead and is, therefore, safe for consumption without the potential of food poisoning.

Proteomic analysis of Rhizobium freirei PRF 81 responses to low pH.

Rhizobium freirei PRF 81 is employed in common bean commercial inoculants in Brazil, due to its outstanding efficiency in fixing nitrogen, competitiveness and tolerance to abiotic stresses. Among the environmental conditions faced by rhizobia in soils, acidity is perhaps the encountered most, especially in Brazil. So, we used proteomics based approaches to study the responses of PRF 81 to a low pH condition. R. freirei PRF 81 was grown in TY medium until exponential phase in two treatments: pH 6,8 and pH 4,8. Whole-cell proteins were extracted and separated by two-dimensional gel electrophoresis, using IPG-strips with pH range 4-7 and 12% polyacrilamide gels. The experiment was performed in triplicate. Protein spots were detected in the high-resolution digitized gel images and analyzed by Image Master 2D Platinum v 5.0 software. Relative volumes (%vol) of compared between the two conditions tested and were statistically evaluated (p ≤ 0.05). Even knowing that R. freirei PRF 81 can still grow in more acid conditions, pH 4.8 was chosen because didn´t affect significantly the bacterial growth kinetics, a factor that could compromise the analysis. Using a narrow pH range, the gel profiles displayed a better resolution and reprodutibility than using broader pH range. Spots were mostly concentrated between pH 5-7 and molecular masses between 17-95 kDa. From the six hundred well-defined spots analyzed, one hundred and sixty-three spots presented a significant change in % vol, indicating that the pH led to expressive changes in the proteome of R. freirei PRF 81. Of these, sixty-one were up-regulated and one hundred two was downregulated in pH 4.8 condition. Also, fourteen spots were only identified in the acid condition, while seven spots was exclusively detected in pH 6.8. Ninety-five differentially expressed spots and two exclusively detected in pH 4,8 were selected for Maldi-Tof identification. Together with the genome sequencing and the proteome analysis of heat stress, we will search for molecular determinants of PRF 81 related to capacity to adapt to stressful tropical conditions.

Exergy analysis of a solar photovoltaic module

PV energy is the direct conversion of solar radiation into electricity. In this paper, an analysis of the influence of parameters such as global irradiance or temperature in the performance of a PV installation has been carried out. A PV module was installed in a building at the University of Málaga, and these parameters were experimentally determined for different days and different conditions of irradiance and temperature. Moreover, IV curves were obtained under these conditions to know the open-circuit voltage and the short-circuit current of the module. With this information, and using the first law of thermodynamics, an energy analysis was performed to determine the energy efficiency of the installation. Similarly, using the second law of thermodynamics, an exergy analysis is used to obtain the exergy efficiency. The results show that the energy efficiency varies between 10% and 12% and the exergy efficiency between 14% and 17%. It was concluded that the exergy analysis is more suitable for studying the performance, and that only electric exergy must be considered as useful exergy. This exergy efficiency can be improved if heat is removed from the PV module surface, and an optimal temperature is reached.

Aerodynamic parametric analysis of an unconventional joined-wing aircraft configuration

In this paper, the experimental results of an unconventional joined-wing aircraft configuration are presented. The test model uses two different wings, forward and rear, both joined in tandem and forming diamond shapes both in plant and front views. The wings are joined in such a way that it is possible to change the rear wing dihedral angle values and the rear wing sweep angle values in 25 different positions that modify the relative distance and the relative height between the wings. To measure the system aerodynamic coefficients itis necessary to perform wind tunnel tests. The datapresented corresponds to the lift, drag and induced drag aerodynamic coefficients, as well as the aerodynamic efficiency and the parameter for minimum required power, from the calculated values of the lift and drag time series measured by a 6-axis force and torque sensor. The results show the influence on the aerodynamic coefficients of the rear wing sweep and dihedral angles parameters. As a main result, it can be concluded that, in general terms, the lift and induced drag aerodynamic coefficients values decrease as both the distance and height between the wings increase, on the other hand, the total drag aerodynamic coefficient decreases if the distance between the wings increases, but nevertheless shows a slight tendency to increase if the height of the rear wing increases, whereas the aerodynamic efficiency and the parameter for minimum required power increase if the distance between the wings increases

Assessing public spending efficiency in 20 OECD countries

Mestrado em Economia Monetária e Financeira

Assessing public spending efficiency in 20 OECD countries

This study follows the framework of Afonso, Schuknecht, and Tanzi (2005), aiming to look at the public expenditure of 20 OECD countries for the period 2009-2013, from the per- spective of efficiency and assess if these developed countries are performing efficiently compared to each other. Public Sector Performance (PSP) and Public Sector Efficiency (PSE) indicators were constructed and Data Envelopment Analysis was conducted. The results show that the only country that performed on the efficiency frontier is Switzerland. The average input-oriented efficiency score is equal to 0.732. That is, on average countries could have reduced the level of public expenditure by 26.8% and still achieved the same level of public performance. The average output-oriented efficiency score is 0.769 denoting that on average the sample countries could have increased their performance by 23.1% by employing the same level of public expenditure.

Eficiência das unidades de saúde familiar na diabetes – uma abordagem por Data Envelopment Analysis

Dissertação de Mestrado, Gestão de Unidades de Saúde, Faculdade de Economia, Universidade do Algarve, 2016

Microwave-assisted solvent extraction and analysis of shikimic acid from plant tissues.

A better method for determination of shikimate in plant tissues is needed to monitor exposure of plants to the herbicide glyphosate [N-(phosphonomethyl)glycine] and to screen the plant kingdom for high levels of this valuable phytochemical precursor to the pharmaceutical oseltamivir. A simple, rapid, and efficient method using microwave-assisted extraction (MWAE) with water as the extraction solvent was developed for the determination of shikimic acid in plant tissues. High performance liquid chromatography was used for the separation of shikimic acid, and chromatographic data were acquired using photodiode array detection. This MWAE technique was successful in recovering shikimic acid from a series of fortified plant tissues at more than 90% efficiency with an interference-free chromatogram. This allowed the use of lower amounts of reagents and organic solvents, reducing the use of toxic and/or hazardous chemicals, as compared to currently used methodologies. The method was used to determine the level of endogenous shikimic acid in several species of Brachiaria and sugarcane (Saccharum officinarum) and on B. decumbens and soybean (Glycine max) after treatment with glyphosate. The method was sensitive, rapid and reliable in all cases.

Performance analysis of brazilian public and philanthropic hospitals

This paper presents the results of a research that aimed at identifying optimal performance standards of Brazilian public and philanthropic hospitals. In order to carry out the analysis, a model based on Data Envelopment Analysis (DEA) was developed. We collected financial data from hospitals’ financial statements available on the internet, as well as operational data from the Information Technology Department of the Brazilian Public Health Care System – SUS (DATASUS). Data from 18 hospitals from 2007 to 2011 were analyzed. Our DEA model used both operational and financial indicators (variables). In order to develop this model, two indicators were considered inputs: Values (in Brazilian Reais) of Fixed Assets and Planned Capacity. On the other hand, the following indicators were considered outputs: Net Margin, Return on Assets and Institutional Mortality Rate. As regards the proposed model, there were five hospitals with optimal performance and four hospitals were considered inefficient, upon the analysis of the variables, considering the analyzed period. Analysis of the weights indicated the most relevant variables for determining efficiency and scale variable values, which is an important tool to aid the decision-making by hospital managers. Finally, the scale variables determined the returns on production, indicating that 14 hospitals work with scale diseconomies. This may indicate inefficiency in the resource management of the Brazilian public health-care system, by analyzing this set of proposed variables.

Dispersive liquid–liquid microextraction for metals enrichment: A useful strategy for improving sensitivity of laser-induced breakdown spectroscopy in liquid samples analysis

A rapid and efficient Dispersive Liquid–Liquid Microextraction (DLLME) followed by Laser-Induced Breakdown Spectroscopy detection (LIBS) was evaluated for simultaneous determination of Cr, Cu, Mn, Ni and Zn in water samples. Metals in the samples were extracted with tetrachloromethane as pyrrolidinedithiocarbamate (APDC) complexes, using vortex agitation to achieve dispersion of the extractant solvent. Several DLLME experimental factors affecting extraction efficiency were optimized with a multivariate approach. Under optimum DLLME conditions, DLLME-LIBS method was found to be of about 4.0–5.5 times more sensitive than LIBS, achieving limits of detection of about 3.7–5.6 times lower. To assess accuracy of the proposed DLLME-LIBS procedure, a certified reference material of estuarine water was analyzed.

Economic efficiency of members of protected designations of origin: sharing reputation indicators in the experience goods of wine and cheese

The aim of this paper is to analyse the economic efficiency of members of protected designations of origin (PDO). For the first time we analyse the value of PDO labels from the point of view of economic efficiency. The central hypothesis is that a PDO has a positive impact on the economic efficiency of its member companies and that this is because a PDO label is a collective reputation indicator that foments efficient investment in quality in terms of member returns. The methodology applied to test this hypothesis is based on data envelopment analysis to estimate economic efficiency, and econometric models to explain company efficiency through both the PDO label, as an indicator of collective reputation, and the characteristics of the company. The results obtained in the experience goods of wine and cheese in Spain show that PDO labels have a positive impact on economic efficiency. Additionally, the age and size of the company have a positive effect while the wage level of the company has a different influence on efficiency depending on the sector considered. Overall, the results reveal the importance of PDOs in industries in which the signal of reputation is not only reliant on the individual brands.

Reliability of graphite furnace atomic absorption spectrometry as alternative method for trace analysis of arsenic in natural medicinal products

Purpose: To evaluate the comparative efficiency of graphite furnace atomic absorption spectrometry (GFAAS) and hydride generation atomic absorption spectrometry (HGAAS) for trace analysis of arsenic (As) in natural herbal products (NHPs). Method: Arsenic analysis in natural herbal products and standard reference material was conducted using atomic absorption spectrometry (AAS), namely, hydride generation AAS (HGAAS) and graphite furnace (GFAAS). The samples were digested with HNO3–H2O2 in a ratio of 4:1 using microwaveassisted acid digestion. The methods were validated with the aid of the standard reference material 1515 Apple Leaves (SRM) from NIST Results: Mean recovery of three different samples of NHPs, using HGAAS and GFAAS, ranged from 89.3 - 91.4 %, and 91.7 - 93.0 %, respectively. The difference between the two methods was insignificant. A (P= 0.5), B (P=0.4) and C (P=0.88) Relative standard deviation (RSD) RSD, i.e., precision was 2.5 - 6.5 % and 2.3 - 6.7 % using HGAAS and GFAAS techniques, respectively. Recovery of arsenic in SRM was 98 and 102 % by GFAAS and HGAAS, respectively. Conclusion: GFAAS demonstrates acceptable levels of precision and accuracy. Both techniques possess comparable accuracy and repeatability. Thus, the two methods are recommended as an alternative approach for trace analysis of arsenic in natural herbal products.