Introducción técnica a la implementación de compresores y descompresores basados en los sistemas Huffman y Lempev-Ziv

Peer-reviewed

Propulsor pneumático versátil e isento de pulsação para sistemas de análise em fluxo

Aquarium air pumps are proposed and evaluated as pneumatic liquid propulsion devices for flow injection and continuos flow analysis (FIA and CFA) systems. This kind of pump is widely available at a very low cost and it can sustain a pressure around of 4 psi (0.28 bar) indefinitely. By applying this air pressure onto a solution contained in a reservoir flask, it is possible to reach flow rates of up to 12.5 mL min-1 for circuits comprising reactors, made from 0.8 i.d. tubing with a length of 100 cm. The precise adjustment of flow rate below the maximum one can be made with a simplified needle valve or inserting in series a short length of capillary tube. The absence of flow pulsation is a definite advantage in comparison with peristaltic pumps, especially when amperometric detection is elected, as confirmed experimentally in FIA and CF applications.

Módulo eletrônico de controle para válvulas solenóides

This technical note describes a new and simple electronic circuit for driving solenoid valves. The circuit is based on a single integrated circuit DRV103, which is able to drive resistive or inductive loads up to 1.5 A. Switching of 12-V loads can be controlled by TTLlevel signals in two distinct steps. Initially, 12 V is applied during 110 ms, followed by 4.2 V RMS until the end of the activation TTL pulse. This mode of operation is particularly suitable to drive solenoids, because it requires a higher voltage to start and a lower maintenance voltage. By using this circuit, power consumption and heating are reduced and the solenoid lifetime is enhanced. Moreover, this circuit is specially appropriated to build computercontrolled solenoid valves systems.

Um banho termostático de baixo custo (temperatura ambiente até 0ºC)

Thermal baths to decrease ambient temperature are an indispensable tool for most research and teaching laboratories, especially those in tropical or equatorial regions. A simple and inexpensive thermal bath has been developed based on a scratched compressor. It has three possible setups for cooling: sample immersed into the bath, sample flowing through the bath, and cooling liquid flowing in a jacket around the sample. It has been tested for 40 months. The temperature ranges from room temperature to 0 °C, when using water. The repeatability is better than 3% and the precision varies from 0.5% to 2%.

Radiaalikompressorin juoksupyörän virtauskanavan suunnittelu

Diplomityössä on tutkittu radiaalikompressorin juoksupyörän virtauskanavan suunnittelua ja esitelty yleisesti käytetyt suunnittelumenetelmät. Virtauskanavan muodon vaikutukset virtauskenttään on esitetty. Työssä on kehitetty uusi tietokoneohjelma juoksupyörän kolmiulotteisen geometrian luomiseen, yksiulotteisesta suunnittelusta saatujen päämittojen pohjalta. Ohjelmalla luotua juoksupyörän geometriaa voidaan käyttää virtaus- ja lujuusanalyyseissä. Ohjelmaan on myös liitetty kaksiulotteinen kokoonpuristuvan viskoosittoman virtauksen ratkaisija.

Protection of the high-voltage equipment with reduced insulation strength

Power transformer is the most expensive equipment on a substation. It is always necessary to get needed benefit with the lowest expenses. Producing of power transformers with reduced insulation strength is one of the possible ways to reduce expenses. Exploitation of such transformers was begun in the end of 70-th in the last century. Protection from overvoltages was done with valve-type magnetic combined surge arresters with increased blanking voltage during switching overvoltages. Nowadays there is the necessity of replacement of those devices. That’s why modernized nonlinear surge arrester was invented. This master’s thesis is focused on the use research of that modernized device in comparison with usual nonlinear surge arresters. The goal is to show the lightning overvoltages level using different types of nonlinear surge arresters and then calculations of the lightning protection reliability.

Acoplamento de cela de difusão gasosa a sistema de análise por injeção seqüencial visando a determinação espectrofotométrica de sulfeto

A new configuration for coupling a gas diffusion cell to a sequential injection system is presented. The matrix exchange is made without the need for additional rotary injection valves or peristaltic pumps, keeping the original mechanical components of the sequential injection apparatus: one syringe pump (or peristaltic pump) and one selection valve. The system was tested constructing analytical curves for sulfide exploring the formation of the methylene blue dye. The proposed method has a detection limit of 60 µg L-1 S2-, with a linear dynamic range between 0.10 and 4.0 mg L-1 S2- concentrations, with a sampling frequency of 20 h-1.

Crassostrea patagonica (d'Orbigny, 1842) shell concentrations from the late Miocene Rio Negro province, NE Patagonia, Argentina

The Río Negro Formation (late Miocene-early Pliocene) mainly consists of continental deposits, but it contains a middle member of marine origin. It represents a transgressive-regressive sequence that can be seen at several outcrops along the N Patagonian coast. The taphonomical approach to the El Espigón marine deposits permits the identification of four main layers containing different kinds of skeletal accumulation, which mainly consist of oyster shells [Crassostrea patagonica (D'Orbigny, 1842)]. These concentrations display three different morphologies (pouches, pavements and bouquets) with a different taphonomic signature. These deposits were formed in shallow marine environments influenced by wave activity that produced valve concentrations of different entities. They contain several shell beds that represent event, composite, hiatal to lag skeletal concentrations. Traces of bioturbation in the sediment (Thalassinoides, Teichichnus) and bioerosion on the shells (Entobia, Gastrochaeonolites, Caulostrepsis), and encrusters (cirripeds, bryozoans), are also abundant in the outcrop and consititue common components of these Miocene materials. Layers 1 and 2 of the sequence were deposited in shoreface/foreshore environments at the beginning of a highstand systems tract, while layers 3 and 4 were deposited at the end, or at the beginning of a forced regression, in foreshore environments. A final erosional episode cut the top of the layer 4, which truncated the abundant bioturbaation developed there.

Flow analysis by using solenoid valves for As(III) determination in natural waters by an on-line separation and pre-concentration system coupled to a tungsten coil atomizer

A flow system coupled to a tungsten coil atomizer in an atomic absorption spectrometer (TCA-AAS) was developed for As(III) determination in waters, by extraction with sodium diethyldithiocarbamate (NaDDTC) as complexing agent, and by sorption of the As(III)-DDTC complex in a micro-column filled with 5 mg C18 reversed phase (10 µL dry sorbent), followed by elution with ethanol. A complete pre-concentration/elution cycle took 208 s, with 30 s sample load time (1.7 mL) and 4 s elution time (71 µL). The interface and software for the synchronous control of two peristaltic pumps (RUN/ STOP), an autosampler arm, seven solenoid valves, one injection valve, the electrothermal atomizer and the spectrometer Read function were constructed. The system was characterized and validated by analytical recovery studies performed both in synthetic solutions and in natural waters. Using a 30 s pre-concentration period, the working curve was linear between 0.25 and 6.0 µg L-1 (r = 0.9976), the retention efficiency was 94±1% (6.0 µg L-1), and the pre-concentration coefficient was 28.9. The characteristic mass was 58 pg, the mean repeatability (expressed as the variation coefficient) was 3.4% (n=5), the detection limit was 0.058 µg L-1 (4.1 pg in 71 µL of eluate injected into the coil), and the mean analytical recovery in natural waters was 92.6 ± 9.5 % (n=15). The procedure is simple, economic, less prone to sample loss and contamination and the useful lifetime of the micro-column was between 200-300 pre-concentration cycles.

Study of a vapor-compression air-conditioning system for jetliners

Most modern passenger aeroplanes use air cycle cooling. A high-speed air cycle is a reliable and light option, but not very efficient. This thesis presents research work done to design a novel vapour cooling cycle for aeroplanes. Due to advancements in high-speed permanent magnet motors, the vapour cycle is seen as a competitive option for the air cycle in aeroplanes. The aerospace industry places tighter demands on the weight, reliability and environmental effects of the machinery than those met by conventional chillers, and thus modifications to conventional design are needed. The thesis is divided into four parts: the initial screening of the working fluid, 1-D design and performance values of the compressor, 1-D off-design value predictions of the compressor and the 3-D design of the compressor. The R245fa was selected as the working fluid based the study. The off-design range of the compressor was predicted to be wide and suitable for the application. The air-conditioning system developed is considerably smaller than previous designs using centrifugal compressors.

Letkuventtiilin mitoitus säätökäyttöön

Tässä diplomityössä käydään läpi IEC-60534 -standardin mukainen säätöventtiilin mitoitus kokoonpuristumattomille ja –puristuville virtauksille laskennassa tarvittavine yhtälöineen. Teoreettisessa osassa esitellään RF-letkuventtiilien rakennetta ja ominaisuuksia. Lisäksi käydään läpi putkivirtauksen perusperiaatteita. Koska letkuventtiilissä virtaavana fluidina on usein jokin liete, on työssä esitelty menetelmä lietevirtauksen aiheuttaman paine-eron laskentaan. Työssä on käsitelty myös kavitaation syntyä, laskennalliset mahdollisuudet kavitaation ennustamiseen sekä keinoja kavitaation estämiseksi. Kokeellisessa osassa suoritettiin mittauksia kolmella erikokoisella RF-letkuventtiilillä, joissa kussakin käytettiin kolmea erityyppistä letkua. Mittausten perusteella pystyttiin laskemaan kapasiteettikertoimet sekä määrittämään säätökäyrät mitatuille venttiileille ja letkutyypeille. Näistä tuloksista säätökäyrille sovitettiin yhtälöt, joiden perusteella saatiin laskettua kapasiteettikertoimien arvot myös muille venttiilikoille.

Cardiac disease in systemic lupus erythematosus: prospective study of 70 patients.

A prospective two dimensional and Doppler echocardiographic study of 70 consecutive patients with systemic lupus erythematosus (SLE) and 40 controls was carried out. Forty patients (57%) were found to have echocardiographic disturbance. Valvular abnormalities were detected in 31 patients (44%) and in only two controls (5%). Mitral valve abnormalities were the most common findings (23/70 (33%)) with mild or moderate regurgitation the most frequent lesion (16% and 9% respectively). Three patients (4%) had a morphological echocardiographic pattern suggestive of non-infective verrucous vegetations affecting the mitral valve. No patient had haemodynamically significant clinical valve disease. Pericardial effusion was identified in 19 patients (27%), of whom 14 had mild and clinically silent disease. Myocardial abnormalities were found in 14 patients (20%), but clinical features of myocardial dysfunction were present in only one. Patients with antiphospholipid antibodies were found to have an increased prevalence of endocardial lesions, mainly valvular regurgitation. It is concluded that the inclusion of echocardiography in a study protocol of patients with SLE can identify an important subset of patients with cardiac abnormalities, many of which are clinically silent. In addition, the association of antiphospholipid antibodies with endocardial lesions suggests that these antibodies may have a prominent role in the pathogenetic mechanisms of heart valve disease in SLE.

Cardiac disease in systemic lupus erythematosus. Prospective study of 70 patients.

A prospective two dimensional and Doppler echocardiographic study of 70 consecutive patients with systemic lupus erythematosus (SLE) and 40 controls was carried out. Forty patients (57%) were found to have echocardiographic disturbance. Valvular abnormalities were detected in 31 patients (44%) and in only two controls (5%). Mitral valve abnormalities were the most common findings (23/70 (33%)) with mild or moderate regurgitation the most frequent lesion (16% and 9% respectively). Three patients (4%) had a morphological echocardiographic pattern suggestive of non-infective verrucous vegetations affecting the mitral valve. No patient had haemodynamically significant clinical valve disease. Pericardial effusion was identified in 19 patients (27%), of whom 14 had mild and clinically silent disease. Myocardial abnormalities were found in 14 patients (20%), but clinical features of myocardial dysfunction were present in only one. Patients with antiphospholipid antibodies were found to have an increased prevalence of endocardial lesions, mainly valvular regurgitation. It is concluded that the inclusion of echocardiography in a study protocol of patients with SLE can identify an important subset of patients with cardiac abnormalities, many of which are clinically silent. In addition, the association of antiphospholipid antibodies with endocardial lesions suggests that these antibodies may have a prominent role in the pathogenetic mechanisms of heart valve disease in SLE.

Siirrettävän kompressorin käyttö maakaasuputkiston huoltotöissä

Maakaasuputkiston huolto- ja muutostöiden yhteydessä joudutaan tyhjentämään putkisto kaasusta, jotta voidaan taata turvalliset työskentelyolosuhteet. Nykyisin putkisto tyhjennetään johtamalla kaasu ilmakehään, avaamalla putkiston ulospuhallusventtiilit. Koska maakaasu (metaani) on merkittävä kasvihuonekaasu, on ympäristövaatimusten tiukentuessa etsittävä vaihtoehtoisia keinoja vähentää päästöjä. Lisäksi, talteen otettu kaasu voidaan myydä edelleen, ja näin ollen saavuttaa säästöjä. Tässä työssä on tutkittu mahdollisuuksia komprimoida kaasu siirrettävän kompressorin avulla putkisto-osuudesta toiseen ilman, että kaasua jouduttaisiin puhaltamaan ilmakehään. Työssä päädyttiin johtopäätökseen, että siirrettävän kompressorin hankinta ei ole tällä hetkellä kannattavaa, sen korkeiden investointikustannusten vuoksi. Kuitenkin mahdollinen päästömaksu metaanille, kaasun arvon nousu, sekä tekniikan parantuminen voivat nostaa menetelmän varteenotettavaksi vaihtoehdoksi hyvinkin nopeasti. Tämän vuoksi jatkotutkimuksen tekeminen aiheesta on perusteltua.