Induction motor load impact on power system eigenvalue sensitivity analysis

Load modelling plays an important role in power system dynamic stability assessment. One of the widely used methods in assessing load model impact on system dynamic response is parametric sensitivity analysis. A composite load model-based load sensitivity analysis framework is proposed. It enables comprehensive investigation into load modelling impacts on system stability considering the dynamic interactions between load and system dynamics. The effect of the location of individual as well as patches of composite loads in the vicinity on the sensitivity of the oscillatory modes is investigated. The impact of load composition on the overall sensitivity of the load is also investigated.

An empirical investigation of health information system failure in regional Sri Lanka

Public health decision making is critically dependant on accurate, timely and reliable information. There is a widespread belief that most of the national and sub-national health information systems fail in providing much needed information support for evidence based health planning and interventions. This situation is more acute in developing nations where resources are either stagnant or decreasing, coupled with the situations of demographic transition and double burden of diseases. Literature abounds with publications, which provide information on misguided health interventions in developing nations, leading to failure and waste of resources. Health information system failure is widely blamed for this situation. Nevertheless, there is a dearth of comprehensive evaluations of existing national or sub-national health information systems, especially in the region of South-East Asia. This study makes an attempt to bridge this knowledge gap by evaluating a regional health information system in Sri Lanka. It explores the strengths and weaknesses of the current health information system and related causative factors in a decentralised health system and then proposes strategic recommendations for reform measures. A mix methodological and phased approach was adopted to reach the objectives. An initial self administered questionnaire survey was conducted among health managers to study their perceptions in relation to the regional health information system and its management support. The survey findings were used to establish the presence of health information system failure in the region and also as a precursor to the more in-depth case study which was followed. The sources of data for the case study were literature review, document analysis and key stake holder interviews. Health information system resources, health indicators, data sources, data management, data quality, and information dissemination were the six major components investigated. The study findings reveal that accurate, timely and reliable health information is unavailable and therefore evidence based health planning is lacking in the studied health region. Strengths and weaknesses of the current health information system were identified and strategic recommendations were formulated accordingly. It is anticipated that this research will make a significant and multi-fold contribution for health information management in developing countries. First, it will attempt to bridge an existing knowledge gap by presenting the findings of a comprehensive case study to reveal the strengths and weaknesses of a decentralised health information system in a developing country. Second, it will enrich the literature by providing an assessment tool and a research method for the evaluation of regional health information systems. Third, it will make a rewarding practical contribution by presenting valuable guidelines for improving health information systems in regional Sri Lanka.

Experimental validation of an unpowered unmanned aerial system : application to forced landing scenarios

The ability to perform autonomous emergency (forced) landings is one of the key technology enablers identified for UAS. This paper presents the flight test results of forced landings involving a UAS, in a controlled environment, and which was conducted to ascertain the performances of previously developed (and published) path planning and guidance algorithms. These novel 3-D nonlinear algorithms have been designed to control the vehicle in both the lateral and longitudinal planes of motion. These algorithms have hitherto been verified in simulation. A modified Boomerang 60 RC aircraft is used as the flight test platform, with associated onboard and ground support equipment sourced Off-the-Shelf or developed in-house at the Australian Research Centre for Aerospace Automation(ARCAA). HITL simulations were conducted prior to the flight tests and displayed good landing performance, however, due to certain identified interfacing errors, the flight results differed from that obtained in simulation. This paper details the lessons learnt and presents a plausible solution for the way forward.

Flight trial of an electro-optical sense-and-avoid system

This paper presents the flight trials of an electro-optical (EO) sense-and-avoid system onboard a Cessna host aircraft (camera aircraft). We focus on the autonomous collision avoidance capability of the sense-and-avoid system; that is, closed-loop integration with the onboard aircraft autopilot. We also discuss the system’s approach to target detection and avoidance control, as well as the methodology of the flight trials. The results demonstrate the ability of the sense-and-avoid system to automatically detect potential conflicting aircraft and engage the host Cessna autopilot to perform an avoidance manoeuvre, all without any human intervention

Developing a framework for planning healthy communities : the Logan Beaudesert health decision support system

In the last few decades, the focus on building healthy communities has grown significantly (Ashton, 2009). There is growing evidence that new approaches to planning are required to address the challenges faced by contemporary communities. These approaches need to be based on timely access to local information and collaborative planning processes (Murray, 2006; Scotch & Parmanto, 2006; Ashton, 2009; Kazda et al., 2009). However, there is little research to inform the methods that can support this type of responsive, local, collaborative and consultative health planning (Northridge et al., 2003). Some research justifies the use of decision support systems (DSS) as a tool to support planning for healthy communities. DSS have been found to increase collaboration between stakeholders and communities, improve the accuracy and quality of the decision-making process, and improve the availability of data and information for health decision-makers (Nobre et al., 1997; Cromley & McLafferty, 2002; Waring et al., 2005). Geographic information systems (GIS) have been suggested as an innovative method by which to implement DSS because they promote new ways of thinking about evidence and facilitate a broader understanding of communities. Furthermore, literature has indicated that online environments can have a positive impact on decision-making by enabling access to information by a broader audience (Kingston et al., 2001). However, only limited research has examined the implementation and impact of online DSS in the health planning field. Previous studies have emphasised the lack of effective information management systems and an absence of frameworks to guide the way in which information is used to promote informed decisions in health planning. It has become imperative to develop innovative approaches, frameworks and methods to support health planning. Thus, to address these identified gaps in the knowledge, this study aims to develop a conceptual planning framework for creating healthy communities and examine the impact of DSS in the Logan Beaudesert area. Specifically, the study aims to identify the key elements and domains of information that are needed to develop healthy communities, to develop a conceptual planning framework for creating healthy communities, to collaboratively develop and implement an online GIS-based Health DSS (i.e., HDSS), and to examine the impact of the HDSS on local decision-making processes. The study is based on a real-world case study of a community-based initiative that was established to improve public health outcomes and promote new ways of addressing chronic disease. The study involved the development of an online GIS-based health decision support system (HDSS), which was applied in the Logan Beaudesert region of Queensland, Australia. A planning framework was developed to account for the way in which information could be organised to contribute to a healthy community. The decision support system was developed within a unique settings-based initiative Logan Beaudesert Health Coalition (LBHC) designed to plan and improve the health capacity of Logan Beaudesert area in Queensland, Australia. This setting provided a suitable platform to apply a participatory research design to the development and implementation of the HDSS. Therefore, the HDSS was a pilot study examined the impact of this collaborative process, and the subsequent implementation of the HDSS on the way decision-making was perceived across the LBHC. As for the method, based on a systematic literature review, a comprehensive planning framework for creating healthy communities has been developed. This was followed by using a mixed method design, data were collected through both qualitative and quantitative methods. Specifically, data were collected by adopting a participatory action research (PAR) approach (i.e., PAR intervention) that informed the development and conceptualisation of the HDSS. A pre- and post-design was then used to determine the impact of the HDSS on decision-making. The findings of this study revealed a meaningful framework for organising information to guide planning for healthy communities. This conceptual framework provided a comprehensive system within which to organise existing data. The PAR process was useful in engaging stakeholders and decision-making in the development and implementation of the online GIS-based DSS. Through three PAR cycles, this study resulted in heightened awareness of online GIS-based DSS and openness to its implementation. It resulted in the development of a tailored system (i.e., HDSS) that addressed the local information and planning needs of the LBHC. In addition, the implementation of the DSS resulted in improved decision- making and greater satisfaction with decisions within the LBHC. For example, the study illustrated the culture in which decisions were made before and after the PAR intervention and what improvements have been observed after the application of the HDSS. In general, the findings indicated that decision-making processes are not merely informed (consequent of using the HDSS tool), but they also enhance the overall sense of ‗collaboration‘ in the health planning practice. For example, it was found that PAR intervention had a positive impact on the way decisions were made. The study revealed important features of the HDSS development and implementation process that will contribute to future research. Thus, the overall findings suggest that the HDSS is an effective tool, which would play an important role in the future for significantly improving the health planning practice.

Evaluation of an Augmented Reality Collaborative Process Modelling System

Identifying, modelling and documenting business processes usually requires the collaboration of many stakeholders that may be spread across companies in inter-organizational business settings. While there are many process modelling tools available, the support they provide for remote collaboration is still limited. This paper investigates the application of virtual environment and augmented reality technologies to remote business process modelling, with an aim to assisting common collaboration tasks by providing an increased sense of immersion in a shared workspace. We report on the evaluation of a prototype system with five key informants. The results indicate that this approach to business process modelling is suited to remote collaborative task settings, and stakeholders may indeed benefit from using augmented reality interfaces.

Good secrets, bad secrets : disclosure in children’s picture books about sexual child abuse

Well over 50 picture books have been published for children on the topic of sexual child abuse (Lampert & Walsh, 2010) many with the aim of teaching their very young readers how to tell the difference between good and bad secrets. This paper looks at three recent picture books for how they focus on disclosure as an end point.

Development of a 3D culture system to study the skeletal metastasis of prostate cancer

In the cancer research field, most in vitro studies still rely on two-dimensional (2D) cultures. However, the trend is rapidly shifting towards using a three-dimensional (3D) culture system. This is because 3D models better recapitulate the microenvironment of cells, and therefore, yield cellular and molecular responses that more accurately describe the pathophysiology of cancer. By adopting technology platforms established by the tissue engineering discipline, it is now possible to grow cancer cells in extracellular matrix (ECM)-like environments and dictate the biophysical and biochemical properties of the matrix. In addition, 3D models can be modified to recapitulate different stages of cancer progression for instance from the initial development of tumor to metastasis. Inevitably, to recapitulate a heterotypic condition, comprising more than one cell type, it requires a more complex 3D model. To date, 3D models that are available for studying the prostate cancer (CaP)-bone interactions are still lacking. Therefore, the aim of this study is to establish a co-culture model that allows investigation of direct and indirect CaP-bone interactions. Prior to that, 3D polyethylene glycol (PEG)-based hydrogel cultures for CaP cells were first developed and growth conditions were optimised. Characterization of the 3D hydrogel cultures show that LNCaP cells form a multicellular mass that resembles avascular tumor. In comparison to 2D cultures, besides the difference in cell morphology, the response of LNCaP cells to the androgen analogue (R1881) stimulation is different compared to the cells in 2D cultures. This discrepancy between 2D and 3D cultures is likely associated with the cell-cell contact, density and ligand-receptor interactions. Following the 3D monoculture study, a 3D direct co-culture model of CaP cells and the human tissue engineered bone (hTEBC) construct was developed. Interactions between the CaP cells and human osteoblasts (hOBs) resulted in elevation of Matrix Metalloproteinase 9 (MMP9) for PC-3 cells and Prostate Specific Antigen (PSA) for LNCaP cells. To further investigate the paracrine interaction of CaP cells and (hOBs), a 3D indirect co-culture model was developed, where LNCaP cells embedded within PEG hydrogels were co-cultured with hTEBC. It was found that the cellular changes observed reflect the early event of CaP colonizing the bone site. In the absence of androgens, interestingly, up-regulation of PSA and other kallikreins is also detected in the co-culture compared to the LNCaP monoculture. This non androgenic stimulation could be triggered by the soluble factors secreted by the hOB such as Interleukin-6. There are also decrease in alkaline phosphatase (ALP) activity and down-regulation of genes of the hOB when co-cultured with LNCaP cells that have not been previously described. These genes include transforming growth factor β1 (TGFβ1), osteocalcin and Vimentin. However, no changes to epithelial markers (e.g E-cadherin, Cytokeratin 8) were observed in both cell types from the co-culture. Some of these intriguing changes observed in the co-cultures that had not been previously described have enriched the basic knowledge of the CaP cell-bone interaction. From this study, we have shown evidence of the feasibility and versatility of our established 3D models. These models can be adapted to test various hypotheses for studies pertaining to underlying mechanisms of bone metastasis and could provide a vehicle for anticancer drug screening purposes in the future.

Investigating the change in three dimensional deformity for idiopathic scoliosis using axially loaded MRI

Background: Adolescent idiopathic scoliosis is a complex three-dimensional deformity, involving a lateral deformity in the coronal plane and axial rotation of the vertebrae in the transverse plane. Gravitational loading plays an important biomechanical role in governing the coronal deformity, however, less is known about how they influence the axial deformity. This study investigates the change in three-dimensional deformity of a series of scoliosis patients due to compressive axial loading. Methods: Magnetic resonance imaging scans were obtained and coronal deformity (measured using the coronal Cobb angle) and axial rotations measured for a group of 18 scoliosis patients (Mean major Cobb angle was 43.4 o). Each patient was scanned in an unloaded and loaded condition while compressive loads equivalent to 50% body mass were applied using a custom developed compressive device. Findings: The mean increase in major Cobb angle due to compressive loading was 7.4 o (SD 3.5 o). The most axially rotated vertebra was observed at the apex of the structural curve and the largest average intravertebral rotations were observed toward the limits of the coronal deformity. A level-wise comparison showed no significant difference between the average loaded and unloaded vertebral axial rotations (intra-observer error = 2.56 o) or intravertebral rotations at each spinal level. Interpretation: This study suggests that the biomechanical effects of axial loading primarily influence the coronal deformity, with no significant change in vertebral axial rotation or intravertebral rotation observed between the unloaded and loaded condition. However, the magnitude of changes in vertebral rotation with compressive loading may have been too small to detect given the resolution of the current technique.

A hierarchical evolutionary algorithmic design (HEAD) system for generating and evolving building design models

This thesis develops a detailed conceptual design method and a system software architecture defined with a parametric and generative evolutionary design system to support an integrated interdisciplinary building design approach. The research recognises the need to shift design efforts toward the earliest phases of the design process to support crucial design decisions that have a substantial cost implication on the overall project budget. The overall motivation of the research is to improve the quality of designs produced at the author's employer, the General Directorate of Major Works (GDMW) of the Saudi Arabian Armed Forces. GDMW produces many buildings that have standard requirements, across a wide range of environmental and social circumstances. A rapid means of customising designs for local circumstances would have significant benefits. The research considers the use of evolutionary genetic algorithms in the design process and the ability to generate and assess a wider range of potential design solutions than a human could manage. This wider ranging assessment, during the early stages of the design process, means that the generated solutions will be more appropriate for the defined design problem. The research work proposes a design method and system that promotes a collaborative relationship between human creativity and the computer capability. The tectonic design approach is adopted as a process oriented design that values the process of design as much as the product. The aim is to connect the evolutionary systems to performance assessment applications, which are used as prioritised fitness functions. This will produce design solutions that respond to their environmental and function requirements. This integrated, interdisciplinary approach to design will produce solutions through a design process that considers and balances the requirements of all aspects of the design. Since this thesis covers a wide area of research material, 'methodological pluralism' approach was used, incorporating both prescriptive and descriptive research methods. Multiple models of research were combined and the overall research was undertaken following three main stages, conceptualisation, developmental and evaluation. The first two stages lay the foundations for the specification of the proposed system where key aspects of the system that have not previously been proven in the literature, were implemented to test the feasibility of the system. As a result of combining the existing knowledge in the area with the newlyverified key aspects of the proposed system, this research can form the base for a future software development project. The evaluation stage, which includes building the prototype system to test and evaluate the system performance based on the criteria defined in the earlier stage, is not within the scope this thesis. The research results in a conceptual design method and a proposed system software architecture. The proposed system is called the 'Hierarchical Evolutionary Algorithmic Design (HEAD) System'. The HEAD system has shown to be feasible through the initial illustrative paper-based simulation. The HEAD system consists of the two main components - 'Design Schema' and the 'Synthesis Algorithms'. The HEAD system reflects the major research contribution in the way it is conceptualised, while secondary contributions are achieved within the system components. The design schema provides constraints on the generation of designs, thus enabling the designer to create a wide range of potential designs that can then be analysed for desirable characteristics. The design schema supports the digital representation of the human creativity of designers into a dynamic design framework that can be encoded and then executed through the use of evolutionary genetic algorithms. The design schema incorporates 2D and 3D geometry and graph theory for space layout planning and building formation using the Lowest Common Design Denominator (LCDD) of a parameterised 2D module and a 3D structural module. This provides a bridge between the standard adjacency requirements and the evolutionary system. The use of graphs as an input to the evolutionary algorithm supports the introduction of constraints in a way that is not supported by standard evolutionary techniques. The process of design synthesis is guided as a higher level description of the building that supports geometrical constraints. The Synthesis Algorithms component analyses designs at four levels, 'Room', 'Layout', 'Building' and 'Optimisation'. At each level multiple fitness functions are embedded into the genetic algorithm to target the specific requirements of the relevant decomposed part of the design problem. Decomposing the design problem to allow for the design requirements of each level to be dealt with separately and then reassembling them in a bottom up approach reduces the generation of non-viable solutions through constraining the options available at the next higher level. The iterative approach, in exploring the range of design solutions through modification of the design schema as the understanding of the design problem improves, assists in identifying conflicts in the design requirements. Additionally, the hierarchical set-up allows the embedding of multiple fitness functions into the genetic algorithm, each relevant to a specific level. This supports an integrated multi-level, multi-disciplinary approach. The HEAD system promotes a collaborative relationship between human creativity and the computer capability. The design schema component, as the input to the procedural algorithms, enables the encoding of certain aspects of the designer's subjective creativity. By focusing on finding solutions for the relevant sub-problems at the appropriate levels of detail, the hierarchical nature of the system assist in the design decision-making process.

Development of a transformation system for sorghum (Sorghum bicolor L.)

Sorghum (Sorghum bicolor (L.) Moench) is the world’s fifth major cereal crop and holds importance as a construction material, food and fodder source. More recently, the potential of this plant as a biofuel source has been noted. Despite its agronomic importance, the use of sorghum production is being constrained by both biotic and abiotic factors. These challenges could be addressed by the use of genetic engineering strategies to complement conventional breeding techniques. However, sorghum is one of the most recalcitrant crops for genetic modification with the lack of an efficient tissue culture system being amongst the chief reasons. Therefore, the aim of this study was to develop an efficient tissue culture system for establishing regenerable embryogenic cell lines, micropropagation and acclimatisation for Sorghum bicolor and use this to optimise parameters for genetic transformation via Agrobacterium-mediated transformation and microprojectile bombardment. Using five different sorghum cultivars, SA281, 296B, SC49, Wray and Rio, numerous parameters were investigated in an attempt to establish an efficient and reproducible tissue culture and transformation system. Using immature embryos (IEs) as explants, regenerable embryogenic cell lines (ECLs) could only be established from cultivars SA281 and 296B. Large amounts of phenolics were produced from IEs of cultivars, SC49, Wary and Rio, and these compounds severely hindered callus formation and development. Cultivar SA281 also produced phenolics during regeneration. Attempts to suppress the production of these compounds in cultivars SA281 and SC49 using activated charcoal, PVP, ascorbic acid, citric acid and liquid filter paper bridge methods were either ineffective or had a detrimental effect on embryogenic callus formation, development and regeneration. Immature embryos sourced during summer were found to be far more responsive in vitro than those sourced during winter. In an attempt to overcome this problem, IEs were sourced from sorghum grown under summer conditions in either a temperature controlled glasshouse or a growth chamber. However, the performance of these explants was still inferior to that of natural summer-sourced explants. Leaf whorls, mature embryos, shoot tips and leaf primordia were found to be unsuitable as explants for establishing ECLs in sorghum cultivars SA281 and 296B. Using the florets of immature inflorescences (IFs) as explants, however, ECLs were established and regenerated for these cultivars, as well as for cultivar Tx430, using callus induction media, SCIM, and regeneration media, VWRM. The best in vitro responses, from the largest possible sized IFs, were obtained using plants at the FL-2 stage (where the last fully opened leaf was two leaves away from the flag leaf). Immature inflorescences could be stored at 25oC for up to three days without affecting their in vitro responses. Compared to IEs, the IFs were more robust in tissue culture and showed responses which were season and growth condition independent. A micropropagation protocol for sorghum was developed in this study. The optimum plant growth regulator (PGR) combination for the micropropagation of in vitro regenerated plantlets was found to be 1.0 mg/L BAP in combination with 0.5 mg/L NAA. With this protocol, cultivars 296B and SA281 produced an average of 57 and 13 off-shoots per plantlet, respectively. The plantlets were successfully acclimatised and developed into phenotypically normal plants that set seeds. A simplified acclimatisation protocol for in vitro regenerated plantlets was also developed. This protocol involved deflasking in vitro plantlets with at least 2 fully-opened healthy leaves and at least 3 roots longer than 1.5 cm, washing the media from the roots with running tap water, planting in 100 mm pots and placing in plastic trays covered with a clear plastic bag in a plant growth chamber. After seven days, the corners of the plastic cover were opened and the bags were completely removed after 10 days. All plantlets were successfully acclimatised regardless of whether 1:1 perlite:potting mix, potting mix, UC mix or vermiculite were used as potting substrates. Parameters were optimised for Agrobacterium-mediated transformation (AMT) of cultivars SA281, 296B and Tx430. The optimal conditions were the use of Agrobacterium strain LBA4404 at an inoculum density of 0.5 OD600nm, heat shock at 43oC for 3 min, use of the surfactant Pluronic F-68 (0.02% w/v) in the inoculation media with a pH of 5.2 and a 3 day co-cultivation period in dark at 22oC. Using these parameters, high frequencies of transient GFP expression was observed in IEs precultured on callus initiation media for 1-7 days as well as in four weeks old IE- and IF-derived callus. Cultivar SA281 appeared very sensitive to Agrobacterium since all tissue turned necrotic within two weeks post-exposure. For cultivar 296B, GFP expression was observed up to 20 days post co-cultivation but no stably transformed plants were regenerated. Using cultivar Tx430, GFP was expressed for up to 50 days post co-cultivation. Although no stably transformed plants of this cultivar were regenerated, this was most likely due to the use of unsuitable regeneration media. Parameters were optimised for transformation by particle bombardment (PB) of cultivars SA281, 296B and Tx430. The optimal conditions were use of 3-7 days old IEs and 4 weeks old IF callus, 4 hour pre- and post-bombardment osmoticum treatment, use of 0.6 µm gold microparticles, helium pressure of 1500 kPa and target distance of 15 cm. Using these parameters for PB, transient GFP expression was observed for up to 14, 30 and 50 days for cultivars SA281, 296B and Tx430, respectively. Further, the use of PB resulted in less tissue necrosis compared to AMT for the respective cultivars. Despite the presence of transient GFP expression, no stably transformed plants were regenerated. The establishment of regenerable ECLs and the optimization of AMT and PB parameters in this study provides a platform for future efforts to develop an efficient transformation protocol for sorghum. The development of GM sorghum will be an important step towards improving its agronomic properties as well as its exploitation for biofuel production.

Mother-child communication about sexual abuse prevention

Two hundred and twelve Australian mothers completed an online survey examining features of mother-child communication about child sexual abuse prevention. Two-thirds (67.5%) of respondents had discussed child sexual abuse prevention with their children. Proportions of mothers talking with their children about child sexual abuse prevention varied according to age range (highest for mothers with children aged 5-12 years) and only child status (lowest for mothers of only children). The number of topics discussed with their children differed according to child gender (greater number of topics discussed by mothers with both girls and boys) and age range (greater number of topics discussed by mothers with children aged 5-12 years). These findings provide new insights into mother-child communication about child sexual abuse prevention.

The experiences of learner drivers, provisional drivers and supervisors with graduated driver licensing in two Australian jurisdictions

Newly licensed drivers on a provisional or intermediate licence have the highest crash risk when compared with any other group of drivers. In comparison, learner drivers have the lowest crash risk. Graduated driver licensing is one countermeasure that has been demonstrated to effectively reduce the crashes of novice drivers. This thesis examined the graduated driver licensing systems in two Australian states in order to better understand the behaviour of learner drivers, provisional drivers and the supervisors of learner drivers. By doing this, the thesis investigated the personal, social and environmental influences on novice driver behaviour as well as providing effective baseline data against which to measure subsequent changes to the licensing systems. In the first study, conducted prior to the changes to the graduated driver licensing system introduced in mid-2007, drivers who had recently obtained their provisional licence in Queensland and New South Wales were interviewed by telephone regarding their experiences while driving on their learner licence. Of the 687 eligible people approached to participate at driver licensing centres, 392 completed the study representing a response rate of 57.1 per cent. At the time the data was collected, New South Wales represented a more extensive graduated driver licensing system when compared with Queensland. The results suggested that requiring learners to complete a mandated number of hours of supervised practice impacts on the amount of hours that learners report completing. While most learners from New South Wales reported meeting the requirement to complete 50 hours of practice, it appears that many stopped practising soon after this goal was achieved. In contrast, learners from Queensland, who were not required to complete a specific number of hours at the time of the survey, tended to fall into three groups. The first group appeared to complete the minimum number of hours required to pass the test (less than 26 hours), the second group completed 26 to 50 hours of supervised practice while the third group completed significantly more practice than the first two groups (over 100 hours of supervised practice). Learner drivers in both states reported generally complying with the road laws and were unlikely to report that they had been caught breaking the road rules. They also indicated that they planned to obey the road laws once they obtained their provisional licence. However, they were less likely to intend to comply with recommended actions to reduce crash risk such as limiting their driving at night. This study also identified that there were relatively low levels of unaccompanied driving (approximately 15 per cent of the sample), very few driving offences committed (five per cent of the sample) and that learner drivers tended to use a mix of private and professional supervisors (although the majority of practice is undertaken with private supervisors). Consistent with the international literature, this study identified that very few learner drivers had experienced a crash (six per cent) while on their learner licence. The second study was also conducted prior to changes to the graduated driver licensing system and involved follow up interviews with the participants of the first study after they had approximately 21 months driving experience on their provisional licence. Of the 392 participants that completed the first study, 233 participants completed the second interview (representing a response rate of 59.4 per cent). As with the first study, at the time the data was collected, New South Wales had a more extensive graduated driver licensing system than Queensland. For instance, novice drivers from New South Wales were required to progress through two provisional licence phases (P1 and P2) while there was only one provisional licence phase in Queensland. Among the participants in this second study, almost all provisional drivers (97.9 per cent) owned or had access to a vehicle for regular driving. They reported that they were unlikely to break road rules, such as driving after a couple of drinks, but were also unlikely to comply with recommended actions, such as limiting their driving at night. When their provisional driving behaviour was compared to the stated intentions from the first study, the results suggested that their intentions were not a strong predictor of their subsequent behaviour. Their perception of risk associated with driving declined from when they first obtained their learner licence to when they had acquired provisional driving experience. Just over 25 per cent of participants in study two reported that they had been caught committing driving offences while on their provisional licence. Nearly one-third of participants had crashed while driving on a provisional licence, although few of these crashes resulted in injuries or hospitalisations. To complement the first two studies, the third study examined the experiences of supervisors of learner drivers, as well as their perceptions of their learner’s experiences. This study was undertaken after the introduction of the new graduated driver licensing systems in Queensland and New South Wales in mid- 2007, providing insights into the impacts of these changes from the perspective of supervisors. The third study involved an internet survey of 552 supervisors of learner drivers. Within the sample, approximately 50 per cent of participants supervised their own child. Other supervisors of the learner drivers included other parents or stepparents, professional driving instructors and siblings. For two-thirds of the sample, this was the first learner driver that they had supervised. Participants had provided an average of 54.82 hours (sd = 67.19) of supervision. Seventy-three per cent of participants indicated that their learners’ logbooks were accurate or very accurate in most cases, although parents were more likely than non-parents to report that their learners’ logbook was accurate (F (1,546) = 7.74, p = .006). There was no difference between parents and non-parents regarding whether they believed the log book system was effective (F (1,546) = .01, p = .913). The majority of the sample reported that their learner driver had had some professional driving lessons. Notwithstanding this, a significant proportion (72.5 per cent) believed that parents should be either very involved or involved in teaching their child to drive, with parents being more likely than non-parents to hold this belief. In the post mid-2007 graduated driver licensing system, Queensland learner drivers are able to record three hours of supervised practice in their log book for every hour that is completed with a professional driving instructor, up to a total of ten hours. Despite this, there was no difference identified between Queensland and New South Wales participants regarding the amount of time that they reported their learners spent with professional driving instructors (X2(1) = 2.56, p = .110). Supervisors from New South Wales were more likely to ensure that their learner driver complied with the road laws. Additionally, with the exception of drug driving laws, New South Wales supervisors believed it was more important to teach safety-related behaviours such as remaining within the speed limit, car control and hazard perception than those from Queensland. This may be indicative of more intensive road safety educational efforts in New South Wales or the longer time that graduated driver licensing has operated in that jurisdiction. However, other factors may have contributed to these findings and further research is required to explore the issue. In addition, supervisors reported that their learner driver was involved in very few crashes (3.4 per cent) and offences (2.7 per cent). This relatively low reported crash rate is similar to that identified in the first study. Most of the graduated driver licensing research to date has been applied in nature and lacked a strong theoretical foundation. These studies used Akers’ social learning theory to explore the self-reported behaviour of novice drivers and their supervisors. This theory was selected as it has previously been found to provide a relatively comprehensive framework for explaining a range of driver behaviours including novice driver behaviour. Sensation seeking was also used in the first two studies to complement the non-social rewards component of Akers’ social learning theory. This program of research identified that both Akers’ social learning theory and sensation seeking were useful in predicting the behaviour of learner and provisional drivers over and above socio-demographic factors. Within the first study, Akers’ social learning theory accounted for an additional 22 per cent of the variance in learner driver compliance with the law, over and above a range of socio-demographic factors such as age, gender and income. The two constructs within Akers’ theory which were significant predictors of learner driver compliance were the behavioural dimension of differential association relating to friends, and anticipated rewards. Sensation seeking predicted an additional six per cent of the variance in learner driver compliance with the law. When considering a learner driver’s intention to comply with the law while driving on a provisional licence, Akers’ social learning theory accounted for an additional 10 per cent of the variance above socio-demographic factors with anticipated rewards being a significant predictor. Sensation seeking predicted an additional four per cent of the variance. The results suggest that the more rewards individuals anticipate for complying with the law, the more likely they are to obey the road rules. Further research is needed to identify which specific rewards are most likely to encourage novice drivers’ compliance with the law. In the second study, Akers’ social learning theory predicted an additional 40 per cent of the variance in self-reported compliance with road rules over and above socio-demographic factors while sensation seeking accounted for an additional five per cent of the variance. A number of Aker’s social learning theory constructs significantly predicted provisional driver compliance with the law, including the behavioural dimension of differential association for friends, the normative dimension of differential association, personal attitudes and anticipated punishments. The consistent prediction of additional variance by sensation seeking over and above the variables within Akers’ social learning theory in both studies one and two suggests that sensation seeking is not fully captured within the non social rewards dimension of Akers’ social learning theory, at least for novice drivers. It appears that novice drivers are strongly influenced by the desire to engage in new and intense experiences. While socio-demographic factors and the perception of risk associated with driving had an important role in predicting the behaviour of the supervisors of learner drivers, Akers’ social learning theory provided further levels of prediction over and above these factors. The Akers’ social learning theory variables predicted an additional 14 per cent of the variance in the extent to which supervisors ensured that their learners complied with the law and an additional eight per cent of the variance in the supervisors’ provision of a range of practice experiences. The normative dimension of differential association, personal attitudes towards the use of professional driving instructors and anticipated rewards were significant predictors for supervisors ensuring that their learner complied with the road laws, while the normative dimension was important for range of practice. This suggests that supervisors who engage with other supervisors who ensure their learner complies with the road laws and provide a range of practice to their own learners are more likely to also engage in these behaviours. Within this program of research, there were several limitations including the method of recruitment of participants within the first study, the lower participation rate in the second study, an inability to calculate a response rate for study three and the use of self-report data for all three studies. Within the first study, participants were only recruited from larger driver licensing centres to ensure that there was a sufficient throughput of drivers to approach. This may have biased the results due to the possible differences in learners that obtain their licences in locations with smaller licensing centres. Only 59.4 per cent of the sample in the first study completed the second study. This may be a limitation if there was a common reason why those not participating were unable to complete the interview leading to a systematic impact on the results. The third study used a combination of a convenience and snowball sampling which meant that it was not possible to calculate a response rate. All three studies used self-report data which, in many cases, is considered a limitation. However, self-report data may be the only method that can be used to obtain some information. This program of research has a number of implications for countermeasures in both the learner licence phase and the provisional licence phase. During the learner phase, licensing authorities need to carefully consider the number of hours that they mandate learner drivers must complete before they obtain their provisional driving licence. If they mandate an insufficient number of hours, there may be inadvertent negative effects as a result of setting too low a limit. This research suggests that logbooks may be a useful tool for learners and their supervisors in recording and structuring their supervised practice. However, it would appear that the usage rates for logbooks will remain low if they remain voluntary. One strategy for achieving larger amounts of supervised practice is for learner drivers and their supervisors to make supervised practice part of their everyday activities. As well as assisting the learner driver to accumulate the required number of hours of supervised practice, it would ensure that they gain experience in the types of environments that they will probably encounter when driving unaccompanied in the future, such as to and from education or work commitments. There is also a need for policy processes to ensure that parents and professional driving instructors communicate effectively regarding the learner driver’s progress. This is required as most learners spend at least some time with a professional instructor despite receiving significant amounts of practice with a private supervisor. However, many supervisors did not discuss their learner’s progress with the driving instructor. During the provisional phase, there is a need to strengthen countermeasures to address the high crash risk of these drivers. Although many of these crashes are minor, most involve at least one other vehicle. Therefore, there are social and economic benefits to reducing these crashes. If the new, post-2007 graduated driver licensing systems do not significantly reduce crash risk, there may be a need to introduce further provisional licence restrictions such as separate night driving and peer passenger restrictions (as opposed to the hybrid version of these two restrictions operating in both Queensland and New South Wales). Provisional drivers appear to be more likely to obey some provisional licence laws, such as lower blood alcohol content limits, than others such as speed limits. Therefore, there may be a need to introduce countermeasures to encourage provisional drivers to comply with specific restrictions. When combined, these studies provided significant information regarding graduated driver licensing programs. This program of research has investigated graduated driver licensing utilising a cross-sectional and longitudinal design in order to develop our understanding of the experiences of novice drivers that progress through the system in order to help reduce crash risk once novice drivers commence driving by themselves.

Relationships between maternal feeding and child weight in younger Australian children – Findings from the NOURISH obesity prevention trial

Studies show that in 3-11 year-olds, parental feeding style is directly associated with child weight [1] and also moderates the association between feeding practices and weight [2]. This cross-sectional study aimed to examine these relationships in younger children. Data from 331 of 698 first-time mothers of healthy term children (151 boys, mean age 24±1 months) enrolled in the NOURISH RCT included (a) measured child weight, (b) self-reported feeding styles and controlling feeding practices, and (c) maternal and child covariates. ANCOVA compared mean child weight-for-age z-score (cWAZ) across 4 feeding styles. Regression examined the associations between cWAZ and 5 controlling feeding practices. Moderated multiple regression analysis was planned to examine effects of feeding style on relationships between feeding practices and cWAZ. Feeding style (indulgent = 38.6%, authoritarian = 35.8%, authoritative = 13.1%, uninvolved = 12.5%) was not independently associated with cWAZ. However, ’pressure to eat’ was negatively associated with cWAZ (�=-0.131, p<0.05) higher pressure associated with lower cWAZ. Given feeding style was not associated with cWAZ, moderation analysis was not performed. Contrary to findings in older children, cWAZ in 2-year-olds was not associated with maternal feeding style. However, the negative association between child weight and pressure feeding found in 6-11year-olds [2] appears to hold in toddlers. Educating mothers about potentially detrimental long-term effects of pressure feeding in early childhood, may be more practical and effective in promoting healthy weight than targeting the less concrete concept of feeding styles. References: [1] Hughes, Appetite, 2005;44:83-92. [2] Hennessy, Appetite, 2010;54:369-377.

A review of system safety failure probability objectives for Unmanned Aircraft Systems

Unmanned Aircraft Systems (UAS) are one of a number of emerging aviation sectors. Such new aviation concepts present a significant challenge to National Aviation Authorities (NAAs) charged with ensuring the safety of their operation within the existing airspace system. There is significant heritage in the existing body of aviation safety regulations for Conventionally Piloted Aircraft (CPA). It can be argued that the promulgation of these regulations has delivered a level of safety tolerable to society, thus justifying the “default position” of applying these same standards, regulations and regulatory structures to emerging aviation concepts such as UAS. An example of this is the proposed “1309” regulation for UAS, which is based on the 1309 regulation for CPA. However, the absence of a pilot on-board an unmanned aircraft creates a fundamentally different risk paradigm to that of CPA. An appreciation of these differences is essential to the justification of the “default position” and in turn, to ensure the development of effective safety standards and regulations for UAS. This paper explores the suitability of the proposed “1309” regulation for UAS. A detailed review of the proposed regulation is provided and a number of key assumptions are identified and discussed. A high-level model characterising the expected number of third party fatalities on the ground is then used to determine the impact of these assumptions. The results clearly show that the “one size fits all” approach to the definition of 1309 regulations for UAS, which mandates equipment design and installation requirements independent of where the UAS is to be operated, will not lead to an effective management of the risks.