Optimal displacement mechanisms beneath shallow foundations on linear-elastic perfectly plastic soil

An energy method for a linear-elastic perfectly plastic method utilising the von Mises yield criterion with associated flow developed in 2013 by McMahon and co-workers is used to compare the ellipsoidal cavity-expansion mechanism, from the same work, and the displacement fields of other research by Levin, in 1995, and Osman and Bolton, in 2005, which utilise the Hill and Prandtl mechanisms respectively. The energy method was also used with a mechanism produced by performing a linear-elastic finite-element analysis in Abaqus. At small values of settlement and soil rigidity the elastic mechanism provides the lowest upper-bound solution, and matches well with finite-element analysis results published in the literature. At typical footing working loads and settlements the cavity-expansion mechanism produces a more optimal solution than the displacement fields within the Hill and Prandtl mechanisms, and also matches well with the published finite-element analysis results in this range. Beyond these loads, at greater footing settlements, or soil rigidity, the Prandtl mechanism is shown to be the most appropriate.

Electroless-plated gold films for sensitive surface plasmon resonance detection of white spot syndrome virus

The paper describes the rapid and label-free detection of the white spot syndrome virus (WSSV) using a surface plasmon resonance (SPR) device based on gold films prepared by electroless plating. The plating condition for obtaining films suitable for SPR measurements was optimized. Gold nanoparticles adsorbed on glass slides were characterized by transmission electron microscopy (TEM). Detection of the WSSV was performed through the binding between WSSV in solution and the anti-WSSV single chain variable fragment (scFv antibody) preimmobilized onto the sensor surface. Morphologies of the as-prepared gold films, gold films modified with self-assembled alkanethiol monolayers, and films covered with antibody were examined using an atomic force microscope (AFM). To demonstrate the viability of the method for real sample analysis, WSSV of different concentrations present in a shrimp hemolymph matrix was determined upon optimizing the surface density of the antibody molecules. The SPR device based on the electroless-plated gold films is capable of detecting concentration of WSSV as low as 2.5 ng/mL in 2% shrimp hemolymph, which is one to two orders of magnitude lower than the level measurable by enzyme-linked immunosorbant assays. (c) 2007 Elsevier B.V. All rights reserved.

Determination of sexual hormones in liquid cosmetics by polymer monolith microextraction coupled with high performance liquid chromatography

A method was presented for the determination of testosterone, methyltestosterone and progesterone in liquid cosmetics by coupling polymer monolith microextraction (PMME) to high performance liquid chromatography with UV detection. A poly (methacrylic acid-ethylene glycol dimethacrylate) monolithic capillary column was selected as the extraction medium, which showed high extraction capacity towards these compounds. To achieve optimum extraction performance, several parameters relating to PMME were investigated, including extraction flow rate and pH value, inorganic salt and organic phase concentration of the sample matrix. By simple dilution with phosphate solution and filtering, the sample solution then could be directly injected into the device for extraction. The limits of detection of testosterone, methyltestosterone and progesterone were calculated to be 2, 3, 2, 8 and 4.6 mu g/L. Good linearity was achieved in the range of 10 to 1000 mu g/L with a linear coefficient. r value above 0. 996. Excellent method reproducibility was found by intra- and inter-day precisions, yielding the relative standard deviations of < 7. 7 % and < 7. 5 %, respectively. Recovery for them in the real samples was between 83% and 119%.

The optimization of high performance liquid chromatographic method for analysis of trace microcystins in natural water bodies

The ratio of methanol., water and trifluoroacetic acid ( TFA) was regulated to change the polarity and the pH of the rinse solution and the eluent, so as to improve the high performance liquid chromatography HPLC) detection method for trace microcystines (MCs) in natural water bodies. The results showed that 40 % similar to 45 % methanol-water solution containing 0. 1 % TFA could get good effects on the rinse of impurity, and 70% methanol-water solution containing 0. 1% TFA could elute all the MCs in solid phase extraction ( SPE) cartridge ( C-18), In this way. it is suggested that, in analysis of environmental samples with high concentration of impurity, impurity should be washed with 40% similar to 45% methanol-water solution containing 0. 1% TFA, and MCs should be eluted with 70% similar to 100% methanol-water solution containing 0. 1% TFA.

Nuclear transfer in leach (Paramisgurnus dabryanus Sauvage) by cell-to-cell electrofusion

To study nuclear transfer in the leach (Paramisgurnus dabryanus Sauvage), blastula and gastrula cells were fused with UV-inactivated oocytes by cell-to-cell electrofusion. To facilitate nuclear transfer, blastula and gastrula cells were cultured or incubated at 4 degreesC in different solutions. TC-199 medium supplemented with 20% calf serum was the best culture solution, and effectively retained the totipotence of blastula or gastrula cells for up to 10 days, It was found that gastrula cells incubated at 4 degreesC had the same totipotence as blastula cells, The optimal UV dosage for inactivation of the oocyte chromatin was 180-240 mJ cm(-2). Electrofusion was carried out in a cone-shaped fusion chamber, which permitted the recipient oocyte and the donor blastula cell to contact one another. The electrofusion procedure resulted in a 10% success rate of normal-appearing fish. Genetic analysis indicated that the nuclear material originated from the donor cell (blastomere) and the oocyte pronucleus did not take part in development.

Changing planar thin film growth into self-assembled island formation by adjusting experimental conditions

Illustrated in this paper are two examples of altering planar growth into self-assembled island formation by adapting experimental conditions. Partial oxidation, undersaturated solution and high temperature change Frank-Van der Merwe (FM) growth of Al0.3Ga0.7As in liquid phase epitaxy (LPE) into isolated island deposition. Low growth speed, high temperature and in situ annealing in molecular beam epitaxy (MBE) cause the origination of InAs/GaAs quantum dots (QDs) to happen while the film is still below critical thickness in Stranski-Krastanow (SK) mode. Sample morphologies are characterized by scanning electron microscopy (SEM) or atomic force microscopy (AFM). It is suggested that such achievements are of value not only to fundamental researches but also to spheres of device applications as well. (c) 2004 Elsevier B.V. All rights reserved.

Processing network models of energy/environment systems

Processing networks are a variant of the standard linear programming network model which are especially useful for optimizing industrial energy/environment systems. Modelling advantages include an intuitive diagrammatic representation and the ability to incorporate all forms of energy and pollutants in a single integrated linear network model. Added advantages include increased speed of solution and algorithms supporting formulation. The paper explores their use in modelling the energy and pollution control systems in large industrial plants. The pollution control options in an ethylene production plant are analyzed as an example. PROFLOW, a computer tool for the formulation, analysis, and solution of processing network models, is introduced.

Experimental Investigation into the Production Behavior of Methane Hydrate in Porous Sediment with Hot Brine Stimulation

The gas production behavior from methane hydrate in porous sediment by injecting the brine with the salinity of 0−24 wt % and the temperature of −1 to 130 °C was investigated in a one-dimensional experimental apparatus. The results show that the gas production process consists of three periods: the free gas production, the hydrate dissociation, and the general gas reservoir production. The hydrate dissociation accompanies the temperature decrease with the injection of the brine (NaCl solution), and the dissociation duration is shortened with the increase of the salinity. With the injection of hot brine, instantaneous hydrate dissociation rate also increases with the increase of the salinity. However, while the NaCl concentration is beyond a certain value, the rate has no longer continued increasing. Thermal efficiency and energy ratio for the hydrate production can be enhanced by injecting hot brine, and the enhanced effectiveness is quite good with the injection of high salinity at lower temperature.

Photochromic diarylethene for polarization holographic optical recording

Photochromic diarylethene, 1,2-bis[2-methyl-5-(3-fluorophenyl)-3-thienyl] perfluorocyleopentene (1a), was synthesized. The compound showed good photochromic reactions both in solution and in PMMA matrix by photo-irradiation. Using the diarylethene lb/PMMA film as recording medium and a He-Ne laser for recording and readout, four types of polarization holographic optical recording were accomplished for the first time. The results show that the orthogonal circular polarization recording is the best method for holographic optical recording when the target photochromic diarylethene is used as recording material. (c) 2006 Published by Elsevier B.V.

Measurement of trace phosphorus in dichlorosilane by high-temperature hydrogen reduction gas chromatography

Dichlorosilane, a gas at normal temperature with a boiling point of 8.3 degrees C, is very difficult to sample and detect using conventional methods. We reduced phosphorus in dichlorosilane to PH3 by hydrogen at high temperature, then PH3 was separated from chlorosilanes by NaOH solution and from other hydrides by chromatographic absorption. Thus the problem of interference of chlorosilanes and other hydrides was overcome and PH, was measured by a double flame photometric detector at 526 nm. This method was sensitive, reliable and convenient and the sensitivity reached as low as 0.04 mu g/l.

Choice of calibration equations of the TSM method

For the reciprocal-test fixtures, there are six independent S-parameters to. be determined, and the thru-short-match (TSM) calibration can provide eight calibration equations. In this paper, the relation of calibration equations is investigated. It has been shown that the four equations obtained from the measurement with a transmission standard can be used simultaneously in the calibration. Experimental results show that the different choice of equations will lead to quite different solution, and the calibration accuracy can be improved by taking advantages of the established relation among the calibration equations and properly choosing calibration equations.

5-氟尿嘧啶-β-环糊精结肠靶向前体药物的研究

5-氟尿嘧啶(5-Fluorouracil， 5-FU)是一种抗代谢药物，广泛用于临床治疗结直肠癌、胃癌、乳腺癌等多种癌症，但其首过代谢显著、亲脂性较低，选择性差、毒副作用大。为克服这些缺点人们对5-FU进行了大量的修饰工作，包括小分子修饰以及与各种载体形成微球、微囊、纳米粒、共价前药等。 环糊精(Cyclodextrin，简称CD)，可被结肠中的糖苷酶特异性地降解成小分子糖，而胃和小肠中由于缺乏相应的酶而使环糊精不被降解，这一特性在结肠药物的靶向输送及释放中有重要应用价值。环糊精中含有丰富的羟基，易进行化学修饰，将药物与环糊精通过共价键结合制成前药，使其在胃和小肠中不降解，而在盲结肠中被特异性的酶降解释出药物，达到结肠靶向释药的目的。研究表明，环糊精作为一种前药载体为结肠靶向释药和缓释、控释系统提供了一种有效的手段。 本工作选择5-氟尿嘧啶为模型药物、β-环糊精作为载体，通过中间体5-FU羧酸衍生物的制备及其与β-环糊精的偶联，合成了系列5-FU-β-CD前体药物，并利用紫外、红外、质谱、核磁、元素分析、热分析等手段对其进行结构表征。同时，还研究了前体药物的体外释药性质。具体内容包括： 1. 含有羧基的5-FU衍生物中间体的合成：(5-氟尿嘧啶-1-基)-乙酸(FUAC)、3-(5-氟尿嘧啶-1-基)-丙酸(FUPC)、5-(5-氟尿嘧啶-1-基)-戊酸(FUVC)的合成。 2. 中间体5-FU的羧酸衍生物与β-CD的偶联：分别通过以6-OTs-β-CD为中间体的取代法和活化酯法，合成了第一面取代和第二面取代的5-FU-β-CD大分子前体药物。在二面取代的前体药物制备中，通过改变原料的比例，合成了系列不同取代度(DS)的2-[(5-氟尿嘧啶-1-基)-乙酰基] -β-环糊精结合物。 3. 对上述前体药物进行体外释放研究：分别考察了前体药物在不同pH缓冲溶液中的水解行为及其在小鼠胃肠道人工体液中的酶解行为，并通过UV-Vis及HPLC对前体药物释放情况进行检测分析。 5-Fluorouracil(5-Fu), commonly known as a broad-spectrum antineoplastic drug, has been widely used in the treatment of various kinds of cancer including colon cancer for 40 years. However, this antitumor agent exhibits serious adverse effects, such as their marrow toxicity, gastrointestinal reaction and low selectivity in their clinical use. In order to improve its antitumor activity and reduce its toxicity, the compound was modified in various ways, including the formation of conjugated prodrugs with kinds of carrier, microsphere and nanoparticles etc. Cyclodextrins(CDs) are known to be barely capable of being hydrolyzed and only slightly absorbed in passing through the stomach and small intestine; however they are fermented into small saccharides by colonic microflora and thus absorbed as small saccharides in the large intestine. This biodegradation property of CDs may be useful as a colon-targeting carrier, and thus CD prodrugs may serve as a source of site-specific delivery of drugs to colon. It was demonstrated that prodrugs of CDs can provide a versatile means for construction of not only colon targeted delivery systems, but also delayed release systems. 5-Fluorouracil was taken as a model drug and β-CD as the carrier in this study. Series prodrugs of 5-FU was prepared through the preparation of reactive 5-FU derivatives containing carboxyl group and coupling to hydroxyl groups of CD. The structures of the conjugates were charactered by using IR, UV–vis, ESI-MS, 1H, 13C-NMR spectra, elemental analyses, and thermal analysis. In vitro hydrolysis behavior in aqueous solution and in rat gastrointestinal tract contents of the conjugates were also investigated. The main content of this dissertation includes following aspects: 1. The preparation of 5-FU derivatives containing carboxyl group: 5-Fluorouracil- acetic acid(FUAC)、3-(5-FU-1)-propionic acid (FUPC)、and 5-(5-FU-1)-valeric acid(FUVC). 2. The coupling of 5-FU derivatives to β-CD: 5-FU was selectively conjugated onto the primary or secondary hydroxyl groups of β-CD through an ester linkage, by the substitution of 6-OTs-β-CD and the activated ester method respectively. For the secondary face conjugation, the degree of substitution(DS) can be controlled by changing the mole ratio of the starting materials(FUAC and β-CD). 3. In vitro release behavior of the conjugates in aqueous solution and in rat gastro- intestinal tract contents of the conjugates were investigated, and the reaction was monitored and analyzed by using UV-Vis and HPLC methods.

Modification of Fe/Cu Multilayers under 2-MeV Xe20+ Irradiation

Multilayers with a structure of Si/[Fe(10 nm)/CU(10 nm)](5) were deposited on Si(100) substrates and then irradiated at room temperature by using 2-MeV Xe20+. The modifications of the multilayers were characterized using a depth profile analysis of the Auger electron spectroscopy (AES) data and the evolution of crystallite structures of the multilayers were analyzed by using X-ray diffraction (XRD). The AES depth profiles indicated that de-mixing of the Fe and the Cu layers was observed at low ion fluences, but inter-mixing of the Fe and the Cu layers was found at high ion fluences and destroyed the layered structure of the multilayers. The obtained XRD patterns showed that, after irradiation by 2-MeV Xe20+ at; 2 x 10(16) ions/cm(2), the peaks of the multilayers related to a Cu-based fee solid solution and an Fe-based bee solid solution phase became visible, which implied that the inter-mixing at the Fe/Cu interface resulted in the formation of new phases. A possible mechanism of modification in the Fe/Cu multilayers induced by ion irradiation is briefly discussed.

Liquid-liquid extraction of Pa-233(V) with Aliquat 336

The extraction of protactinium with Aliquat 336 (methyl-tri-caprylyl ammonium chloride) in toluene, cyclohexane and chloroform from HCl, HNO3, H2SO4, HClO4, HF and mixed HCl-HF media was investigated by radioactive tracer technique. Distribution ratios of protactinium between the aqueous solution and the organic phase were determined as a function of shaking time, concentrations of acid in aqueous solution phase, extractant concentration and type of diluents in the organic phase. Aliquat 336 can almost quantitatively extract protactinium from strong HCl solution. At the same time, small amounts of HF in HCl solutions have a strong effect on Pa distribution.