Local plastic mechanisms in thin steel plates under in-plane compression

Thin-walled steel plates subjected to in-plane compression develop two types of local plastic mechanism, namely the roof-shaped mechanism and the so-called flip-disc mechanism, but the intriguing question of why two mechanisms should develop was not answered until recently. It was considered that the location of first yield point shifted from the centre of the plate to the midpoint of the longitudinal edge depending on the b/t ratio, imperfection level, and yield stress of steel, which then decided the type of mechanism. This paper has verified this hypothesis using analysis and laboratory experiments. An elastic analysis using Galerkin's method to solve Marguerre's equations was first used to determine the first yield point, based on which the local plastic mechanism/imperfection tolerance tables have been developed which give the type of mechanism as a function of b/t ratio, imperfection level and yield stress of steel. Laboratory experiments of thin-walled columns verified the imperfection tolerance tables and thus indirectly the hypothesis. Elastic and rigid-plastic curves were them used to predict the effect on the ultimate load due to the change of mechanism. A finite element analysis of selected cases also confirmed the results from simple analyses and experiments.

Cyclone intensity categories

The weather forecast centers in Australia and many other countries use a scale of cyclone intensity categories (categories 1-5) in their cyclone advisories, which are considered to be indicative of the cyclone damage potential. However, this scale is mainly based on maximum gust wind speeds. In a recent research project involving computer modeling of cyclonic wind forces on roof claddings and fatigue damage to claddings, it was found that cyclone damage not only depends on the maximum gust wind speed, but also on two other cyclone parameters, namely, the forward speed and radius to maximum winds. This paper describes the computer model used in predicting the cyclone damage to claddings and investigates the damage potential of a cyclone as a function of all the relevant cyclone parameters, based on which it attempts to refine the current scale of cyclone intensity categories.

Pull-out strength of steel roof and wall cladding systems

When steel roof and wall cladding systems are subjected to wind uplift/suction forces, local pull-through/dimpling failures or pull-out failures occur prematurely at their screwed connections. During extreme wind events such as storms and hurricanes, these localized failures then lead to severe damage to buildings and their contents. An investigation was therefore carried out to study the failure that occurs when the screw fastener pulls out of the steel battens, purlins, or girts. Both two-span cladding tests and small-scale tests were conducted using a range of commonly used screw fasteners and steel battens, purlins, and girts. Experimental results showed that the current design formula may not be suitable unless a reduced capacity factor of 0.4 is used. Therefore, an improved design formula has been developed for pull-out failures in steel cladding systems. The formula takes into account thickness and ultimate tensile strength of steel, along with thread diameter and the pitch of screw fasteners, in order to model the pull-out behavior more accurately. This paper presents the details of this experimental investigation and its results.

Made by motion, Series one

“Made by Motion” is a collaboration between digital artist Paul Van Opdenbosch and performer and choreographer Elise May; a series of studies on captured motion data used to generating experimental visual forms that reverberate in space and time. The project investigates the invisible forces generated by and influencing the movement of a dancer. Along with how the forces can be captured and applied to generating visual outcomes that surpass simple data visualisation, projecting the intent of the performer’s movements. The source or ‘seed’ comes from using an Xsens MVN - Inertial Motion Capture system to capture spontaneous dance movements, with the visual generation conducted through a customised dynamics simulation. In this first series the visual investigation focused on manipulating the movement date at the instance of capture, capture been the recording of three-dimensional movement as ‘seen’ by the hardware and ‘understood’ through the calibration of software. By repositioning the capture hardware on the body we can effectively change how the same sequence of movements is ‘seen’ by the motion capture system thus generating a different visual result from effetely identical movement. The outcomes from the experiments clearly demonstrates the effectiveness of using motion capture hardware as a creative tool to manipulate the perception of the capture subject, in this case been a sequence of dance movements. The creative work exhibited is a cross-section of the experiments conducted in practice with the first animated work (Movement A - Control) using the motion capture hardware in its default ‘normal’ configuration. Following this is the lower body moved to the upper body (Lb-Ub), right arm moved onto the left arm (Ra-La), right leg moved onto the left leg (Rl-Ll) and finally the left leg moved onto a object that is then held in the left hand (Ll-Pf (Lh)).

Experimental arts practice incorporating motion capture

My practice-led research explores and maps workflows for generating experimental creative work involving inertia based motion capture technology. Motion capture has often been used as a way to bridge animation and dance resulting in abstracted visuals outcomes. In early works this process was largely done by rotoscoping, reference footage and mechanical forms of motion capture. With the evolution of technology, optical and inertial forms of motion capture are now more accessible and able to accurately capture a larger range of complex movements. Made by Motion is a collaboration between digital artist Paul Van Opdenbosch and performer and choreographer Elise May; a series of studies on captured motion data used to generate experimental visual forms that reverberate in space and time. The project investigates the invisible forces generated by and influencing the movement of a dancer. Along with how the forces can be captured and applied to generating visual outcomes that surpass simple data visualisation, projecting the intent of the performer’s movements. The source or ‘seed’ comes from using an Xsens MVN – Inertial Motion Capture system to capture spontaneous dance movements, with the visual generation conducted through a customised dynamics simulation. In my presentation I will be displaying and discussing a selected creative works from the project along with the process and considerations behind the work.

Skin cancer prevention and fashion – frontier bedfellows

Problem Queensland has the highest rates of skin cancer in the world, even after wide-ranging public programs promoting sun safety awareness. To-date, public awareness campaigns on the dangers of excessive sun exposure have been highly successful. For adolescents, however, where a significant amount of lifetime sun exposure occurs, perilous exposure still ensues, despite awareness of the risks. New frontier approaches are required to target this key audience cluster, for this significant national problem. Approach For the majority of adolescents, being part of a collective norm defines their visual, attitudinal and behavioural actions and fashion has been validated as one of the most powerful forces that can form, shape and bolster these norms. Considering clothing is the easiest method to limit the amount of skin exposed to UV, fashion (in its many subtle, yet influential guises) is proposed as an avenue to advance positive sun safe practices for adolescents. Through an action-led methodology, this research explores the potential of fashion, as one of the key parts of a complex equation, to be a prime driver to facilitate sun safety for adolescents. Findings This paper advocates that fashion, as distinguishable from clothing, has the potential to positively influence sun protective behaviour. The findings go further and recommend the use of fashion as a stealth driver for sun safety advancement, for adolescents in particular, via shifts in norms of beauty and targeted generational communication strategies. This frontier approach has the potential to significantly reduce risky sun exposure in adolescence.

Primary stability of two uncemented acetabular components of different geometry : hemispherical or peripherally enhanced?

Objective This study compared the primary stability of two commercially available acetabular components from the same manufacturer, which differ only in geometry; a hemispherical and a peripherally enhanced design (peripheral self-locking (PSL)). The objective was to determine whether altered geometry resulted in better primary stability. Methods Acetabular components were seated with 0.8 mm to 2 mm interference fits in reamed polyethylene bone substrate of two different densities (0.22 g/cm3 and 0.45 g/cm3). The primary stability of each component design was investigated by measuring the peak failure load during uniaxial pull-out and tangential lever-out tests. Results There was no statistically significant difference in seating force (p = 0.104) or primary stability (pull-out p = 0.171, lever-out p = 0.087) of the two components in the low-density substrate. Similarly, in the high-density substrate, there was no statistically significant difference in the peak pull-out force (p = 0.154) or lever-out moment (p = 0.574) between the designs. However, the PSL component required a significantly higher seating force thanthe hemispherical cup in the high-density bone analogue (p = 0.006). Conclusions Higher seating forces associated with the PSL design may result in inadequate seating and increased risk of component malpositioning or acetabular fracture in the intra-operative setting in high-density bone stock. Our results, if translated clinically, suggest that a purely hemispherical geometry may have an advantage over a peripherally enhanced geometry in high density bone stock.

Reliability of spatiotemporal and kinetic gait parameters determined by a new instrumented treadmill system

Background Despite the emerging use of treadmills integrated with pressure platforms as outcome tools in both clinical and research settings, published evidence regarding the measurement properties of these new systems is limited. This study evaluated the within– and between–day repeatability of spatial, temporal and vertical ground reaction forces measured by a treadmill system instrumented with a capacitance–based pressure platform. Methods Thirty three healthy adults (mean age, 21.5 ± 2.8 years; height, 168.4 ± 9.9 cm; and mass, 67.8 ± 18.6 kg), walked barefoot on a treadmill system (FDM–THM–S, Zebris Medical GmbH) on three separate occasions. For each testing session, participants set their preferred pace but were blinded to treadmill speed. Spatial (foot rotation, step width, stride and step length), temporal (stride and step times, duration of stance, swing and single and double support) and peak vertical ground reaction force variables were collected over a 30–second capture period, equating to an average of 52 ± 5 steps of steady–state walking. Testing was repeated one week following the initial trial and again, for a third time, 20 minutes later. Repeated measures ANOVAs within a generalized linear modelling framework were used to assess between–session differences in gait parameters. Agreement between gait parameters measured within the same day (session 2 and 3) and between days (session 1 and 2; 1 and 3) were evaluated using the 95% repeatability coefficient. Results There were statistically significant differences in the majority (14/16) of temporal, spatial and kinetic gait parameters over the three test sessions (P < .01). The minimum change that could be detected with 95% confidence ranged between 3% and 17% for temporal parameters, 14% and 33% for spatial parameters, and 4% and 20% for kinetic parameters between days. Within–day repeatability was similar to that observed between days. Temporal and kinetic gait parameters were typically more consistent than spatial parameters. The 95% repeatability coefficient for vertical force peaks ranged between ± 53 and ± 63 N. Conclusions The limits of agreement in spatial parameters and ground reaction forces for the treadmill system encompass previously reported changes with neuromuscular pathology and footwear interventions. These findings provide clinicians and researchers with an indication of the repeatability and sensitivity of the Zebris treadmill system to detect changes in common spatiotemporal gait parameters and vertical ground reaction forces.

Dynamic load sharing in heavy vehicle suspensions - further analysis of the equalisation effects of larger air lines

This paper provides details on comparative testing of axle-to-chassis forces of two heavy vehicles (HVs) based on an experimental programme carried out in 2007. Dynamic forces at the air springs were measured against speed and roughness values for the test roads used. One goal of that programme was to determine whether dynamic axle-to-chassis forces could be reduced by using larger-than-standard diameter longitudinal air lines. This paper presents a portion of the methodology, analysis and results from that programme. Two analytical techniques and their results are presented. The first uses correlation coefficients of the forces between air springs and the second is a student’s t-test. These were used to determine the causality surrounding improved dynamic load sharing between heavy vehicle air springs with larger air lines installed longitudinally compared with the standard sized air lines installed on the majority of air-sprung heavy vehicles.

Make-Buy Decisions in the Face of Radical Innovations

Make-buy decisions are an important aspect of the overall strategic plans for most firms, and the introduction of a new and potentially radical technology into an industry should therefore be a cue for managers to review their make-buy policies. Should a company make in-house the components and processes underpinning the technology, or should it buy them from an outside supplier? Earlier attempts to answer this question may have failed to agree on a single verdict because they have overlooked two important market forces: supplier relations and industry clockspeed. Based on an intensive three-year study at the University of Cambridge which analyzed supply chain management practices from a broad range of manufacturers around the world, this book helps to resolve this classic technology outsourcing dilemma and gives managers the tools they will need to determine if they should make or buy the components and processes that go into a potentially radical innovation.

Dry powder inhaler formulations-effect of polymer carrier size on the drug dispersion

Background The size of the carrier influences the aerosolization of drug from a dry powder inhaler (DPI) formulation. Currently, lactose monohydrate particles in a variety of sizes are preferably used in carrier based DPI formulations of various drugs; however, contradictory reports exist regarding the effect of the size of the carrier on the dispersion of drug. In this study we examined the influence of the intrinsic particle size of the polymeric carrier on the aerosolization of a model drug salbutamol sulphate (SS). Methods Four different sizes (20–150 lm) of polymer carriers were fabricated using solvent evaporation technique and the dispersion of SS particles from these carriers was measured by a Twin Stage Impinger (TSI). The size and morphological properties of polymer carriers were by laser diffraction and SEM, respectively. Results The FPF from these carriers was found to be increasing from 5.6% to 21.3% with increasing the carrier size. The FPF was found to be greater (21%) with the highest particle size of the carrier (150 lm). Conclusions The aerosolization of drug was dependent on the size of polymer carriers. The smaller size of the carrier resulted in lower FPF which was increased with increasing the carrier size. For a fixed mass of drug particles in a formulation, the mass of drug particles per unit area of carriers is higher in formulations containing the larger carriers, which leads to an increase in the dispersion of drug due to the increased mechanical forces occurred between the carriers and the device walls.

Colloidal drug probe : method development and validation for adhesion force measurement using atomic force microscopy

This study demonstrates a novel technique of preparing drug colloid probes to determine the adhesion force between the drug salbutamol sulphate (SS) and the surfaces of polymer microparticles to be used as carriers for the dispersion of drug particles from a dry powder inhaler (DPI) formulation. Initially model silica probes of approximately 4 μm size, similar to a drug particle used in DPI formulations, were coated with a saturated SS solution with the aid of capillary forces acting between the silica probe and the drug solution. The developed method of ensuring a smooth and uniform layer of SS on the silica probe was validated using X-Ray Photoelectron Spectroscopy (XPS) and Scanning Electron Microscopy (SEM). Using the same technique, silica microspheres preattached on the AFM cantilever were coated with SS. The adhesion forces between the silica probe and drug coated silica (drug probe) and polymer surfaces (hydrophilic and hydrophobic) were determined. Our experimental results showed that the technique for preparing the drug probe was robust and can be used to determine the adhesion force between hydrophilic/hydrophobic drug probe and carrier surfaces to gain a better understanding on drug carrier adhesion forces in DPI formulations.

FRC erection stages dynamic behaviour under wind loads

Buffeting response of a cable-stayed bridge under construction is investigated through wind tunnel tests and numerical simulations. Two configurations of the erection stage have been considered and compared in terms of dynamic response and internal forces using the results of the experimental aeroelastic models. Moreover the results of a numerical model able to simulate the simultaneous effects of vortex shedding from tower and aeroelastic response of the deck are compared to the wind tunnel ones.

The competing-complementarity of social media

This study presents the unique benevolent and malevolent nature of social media, intertwined to its capabilities, which influences its role as a benefactor and a competitor. We conceptualize this phenomenon as the competing-complementarity of social media. We explain competing-complementarity using Teece’s (1986) concept of complementary assets and Porter’s (2001) work on competitive forces shaping strategy and business on the Internet. We observe this phenomenon of competing-complementarity of social media on news firms and offer its evidence through opinionated data analysis.

WATER - a series of photographs by Louise Grayson

This body of photographic work has been created to firstly, explore a new approach to practice-led research that uses an “action genre” approach to reflective practice (Lemke) and secondly, to visually explore human interaction with the fundamental item in life - water. The first of these is based on the contention that to understand the meanings inherent in photographs we cannot look merely at the end result. It is essential to keep looking at the actions of practitioners, and the influences upon them, to determine how external influences affect the meaning potential of editorial photographs (Grayson, 2012). WATER therefore, provides an ideal platform to reflect upon the actions and influences involved in creating work within the photographic genre of photojournalism. It enables this practitioner to reflect on each stage of production to gain a better understanding of how external influences impact the narrative potential within images created. There are multi-faceted influences experienced by photographers who are creating images that, in turn, are part of constructing and presenting the narrative potential of editorial photographs. There is an important relationship between professional photographers and the technical, cultural, economic and institutional forces that impinge upon all stages of production and publication. What results is a greater understanding of technical, cultural, economic and institutional forces that impinge upon all stages of production and publication. Therefore, to understand the meanings inherent in photographs within WATER, I do not look merely at the end result. It provides a case study looking at my actions in the filed, and the influences upon me, to determine how external influences affect the meaning potential of these photographs (Grayson, 2012). As a result, this project adds to the body of scholarship around the definition of Photojournalism, how it has adapted to the current media environment and provides scope for further research into emerging new genres within editorial photography, such as citizen photojournalism. Concurrently, the photographs themselves were created to visually explore how there remains a humanistic desire to interact with the natural form of water even while living a modern cosmopolitan life around it. Taking a photojournalistic approach to exploring this phenomenon, the images were created by “capturing moments as they happened” with no posing or setting up of images. This serendipitous approach to the photographic medium provides the practitioner with at least an attempt to direct the subjectivity contained explicitly in photographs. What results is a series of images that extend the visual dialogue around the role of water within modern humanistic lifestyles and how it remains an integral part of our society’s behaviors. It captures important moments that document this relationship at this time of modern development. The resulting works were exhibited and published as part of the Head On Photo Festival, Australia's largest photo festival and the world's second largest festival in Sydney 20-24 May 2013. The WATER series of images were curated by three Magnum members; Ian Berry, Eli Reed and Chris Steele-Perkins. Magnum is a highly regarded international photographic co-operative with editorial offices in New York, London, Paris and Tokyo. There was a projection of the works as part of the official festival programme, presented to both members of the public and Sydney’s photography professionals. In addition, a sample of images from the WATER series was chosen for inclusion in the Magnum-published hardcover book. References Grayson, Louise. 2012. “Editorial photographs and patterns of practice.” Journalism Practice. Accessed: http://www.tandfonline.com/doi/abs/10.1080/17512786.2012.726836#.UbZN-L--1RQ Lemke, Jay. 1995. Textual Politics: Discourse and Social Dynamics. London: Taylor & Francis.