Direct measurement of plowing friction and wear of a polymer thin film using the atomic force microscope

Nanometer-scale plowing friction and wear of a polycarbonate thin film were directly measured using an atomic force microscope (AFM) with nanoscratching capabilities. During the nanoscratch tests, lateral forces caused discrepancies between the maximum forces for the initial loadings prior to the scratch and the unloading after the scratch. In the case of a nanoscratch test performed parallel to the cantilever probe axis, the plowing friction added another component to the moment acting at the cantilevered end compared to the case of nanoindentation, resulting in an increased deflection of the cantilever. Using free-body diagrams for the cases of nanoindentation and nanoscratch testing, the AFM force curves were analyzed to determine the plowing friction during nanoscratch testing. From the results of this analysis, the plowing friction was found to be proportional to the applied contact force, and the coefficient of plowing friction was measured to be 0.56 +/- 0.02. Also, by the combination of nanoscratch and nanoindentation testing, the energetic wear rate of the polycarbonate thin film was measured to be 0.94 +/- 0.05 mm(3)/(N m).

Experimental measurement of polyethylene chain modulus by scanning force microscopy

Nanoindentation technique and scanning force microscopy have been used to measure directly the polyethylene modulus along the chain axis. Single crystals of polyethylene were employed in order to obtain well-aligned chain segments. To minimize effects of scanner creep, a Z scan rate of 3 Hz was employed. The "X Rotate" value of 25 degrees was selected to eliminate effects of lateral tip motion. The results were analyzed by the Oliver -Pharr method for which direct observation and measurement of the contact area are not required. Considering the influence of tip roundness on the projected contact area, the nanoindentation results were analyzed by the Sawa method. The chain modulus obtained from the thinner polyethylene single crystal sample was 204 +/- 21 GPa by the Oliver-Pharr method and 168 +/- 17 GPa by the Sawa method. The lower values than expected were due to substrate effects and anisotropy of chain deformation during nanoindentation. An extrapolation of the chain modulus obtained by various strains to zero nanoindentation eliminated the effect of substrate and anisotropy of chain deformation. The corresponding chain modulus obtained from the thicker sample was 278 GPa by the Oliver-Pharr method and 267 GPa by the Sawa method, respectively, in better agreement with the value of 340 Cpa determined theoretically. (C) 2001 Elsevier Science Ltd. All rights reserved.

Atomic force microscopy imaging of molybdenum oxide film electrodeposited on a carbon electrode

Non-stoichiometric mixed-valent molybdenum(VI, V) oxide film was grown on carbon substrates by the electrodeposition method. Responses of the prepared molybdenum oxide thin films to potential and to different solution acidities were studied by cyclic voltammetry, and the corresponding morphological changes of the film were monitored by atomic force microscopy (AFM). AFM images of the molybdenum oxide film show that the characteristic domed structure on the film surface increased during the transition from the oxidized state to the reduced state without signification change in the KMS surface roughness value. Furthermore, AFM studies show that the solution acidity has great effect on the morphology of the films, and the films undergo a homogenizing process with increasing pH of the solutions. (C) 1999 Elsevier Science S.A. All rights reserved.

Effect of Eu3+ on the domain structures in phosphatidylcholine LB monolayer film observed by atomic force microscopy

Ordered domain structures were observed by atomic force microscope in dipalmitoylphosphatidycholine monolayer film, which was spread on the subphase of Eu3+ solution.

Lanthanide ion induced formation of stripes domain structure in phospholipid Langmuir-Blodgett monolayer film observed by atomic force microscopy

Long-range ordered stripes domain structures were observed in Dipalmitoylphosphatidylcholine (DPPC) Langmuir-Blodgett monolayer film which was spread on the subphase of lanthanide ion (Eu3+) solution and transferred to a freshly cleaved mica substrate by vertical deposition. This novel phenomenon was discussed in terms of the competitive interaction of dipole-dipole and electrostatic interactions of the DPPC molecules combined with lanthanide ions with those DPPC molecules free of lanthanide ions.

SCANNING-TUNNELING-MICROSCOPY (STM) AND LATERAL FORCE MICROSCOPY (LFM) INVESTIGATION OF THE STRUCTURE AND CHARACTER OF CONDUCTIVE POLYPYRROLE FILM

Polypyrrole doped with p-toluenesulfonate was electropolymerized onto highly oriented pyrolytic graphite (HOPG), glassy carbon (GC) and Pt electrode surfaces under the same experimental conditions. The resulting films were studied by scanning tunneling m

THE DETERMINATION OF STANDARD ELECTROMOTIVE FORCE OF CELL Cu vertical bar CuSO4 vertical bar Hg2SO4-Hg AT DIFFERENT TEMPERATURES

The emfs of Cu|CuSO_4|Hg_2SO_4-Hg were determined at 5 temperature points from 278.15K to 313.15K. Based on the Pitzer' s Equation a polynomial approximation for the determination of standard emf, E_m, was proposed. The values of E_m obtained by author's method agree with values of E_m obtained by the extended Debye-Huckel equation within experimental errors. Compared with the extrapolation result of extended Debye-Huckel equation, the uncertainty by the selecting of parameter of ion size was avoided.By the...

Is inorganic nutrient enrichment a driving force for the formation of red tides? A case study of the dinoflagellate Scrippsiella trochoidea in an embayment

Red tides (high biomass phytoplankton blooms) have frequently occurred in Hong Kong waters, but most red tides occurred in waters which are not very eutrophic. For example, Port Shelter, a semi-enclosed bay in the northeast of Hong Kong, is one of hot spots for red tides. Concentrations of ambient inorganic nutrients (e.g. N, P), are not high enough to form the high biomass of chlorophyll a (chl a) in a red tide when chl a is converted to its particulate organic nutrient (N) (which should equal the inorganic nutrient, N). When a red tide of the dinoflagellate Scrippsiella trochoidea occurred in the bay, we found that the red tide patch along the shore had a high cell density of 15,000 cells ml(-1), and high chl a (56 mu g l(-1)), and pH reached 8.6 at the surface (8.2 at the bottom), indicating active photosynthesis in situ. Ambient inorganic nutrients (NO3, PO4, SiO4, and NH4) were all low in the waters and deep waters surrounding the red tide patch, suggesting that the nutrients were not high enough to support the high chl a >50 mu g l(-1) in the red tide. Nutrient addition experiments showed that the addition of all of the inorganic nutrients to a non-red-tide water sample containing low concentrations of Scrippsiella trochoidea did not produce cell density of Scrippsiella trochoidea as high as in the red tide patch, suggesting that nutrients were not an initializing factor for this red tide. During the incubation of the red tide water sample without any nutrient addition, the phytoplankton biomass decreased gradually over 9 days. However, with a N addition, the phytoplankton biomass increased steadily until day 7, which suggested that nitrogen addition was able to sustain the high biomass of the red tide for a week with and without nutrients. In contrast, the red tide in the bay disappeared on the sampling day when the wind direction changed. These results indicated that initiation, maintenance and disappearance of the dinoflagellate Scrippsiella trochoidea red tide in the bay were not directly driven by changes in nutrients. Therefore, how nutrients are linked to the formation of red tides in coastal waters need to be further examined, particularly in relation to dissolved organic nutrients. (C) 2008 Elsevier B.V. All rights reserved.

Sensitisation identification of stainless steel to intergranular stress corrosion cracking by atomic force microscopy

A new technique was developed for characterisation of stainless steel to intergramilar stress corrosion cracking by atomic force microscopy. The technique proved to be effective in sensitisation identification of AISI 304 stainless steel and might be promising in sensitisation identification of other stainless steels. (c) 2007 Elsevier B.V. All rights reserved.

Global negative vegetation feedback to climate warming responses of leaf litter decomposition rates in cold biomes

Whether climate change will turn cold biomes from large long-term carbon sinks into sources is hotly debated because of the great potential for ecosystem-mediated feedbacks to global climate. Critical are the direction, magnitude and generality of climate responses of plant litter decomposition. Here, we present the first quantitative analysis of the major climate-change-related drivers of litter decomposition rates in cold northern biomes worldwide. Leaf litters collected from the predominant species in 33 global change manipulation experiments in circum-arctic-alpine ecosystems were incubated simultaneously in two contrasting arctic life zones. We demonstrate that longer-term, large-scale changes to leaf litter decomposition will be driven primarily by both direct warming effects and concomitant shifts in plant growth form composition, with a much smaller role for changes in litter quality within species. Specifically, the ongoing warming-induced expansion of shrubs with recalcitrant leaf litter across cold biomes would constitute a negative feedback to global warming. Depending on the strength of other (previously reported) positive feedbacks of shrub expansion on soil carbon turnover, this may partly counteract direct warming enhancement of litter decomposition.

纳电子器件制备的单根碳纳米管精确装配与电连接研究

目前,利用单根碳纳米管进行纳电子器件的研制成为纳电子学界研究的前沿与热点,但在纳电子器件研制过程中,如何实现单根碳纳米管与微电极的精确装配与电连接成为关键技术难题之一。为探索实现此关键技术的新方法,本文尝试将介电电泳与具有实时力/视觉反馈的原子力显微镜操作方法相结合,从而结合粗、精两级操作方式,来实现单根碳纳米管的精确装配与电连接。单根多壁碳纳米管的精确装配与电特性测试实验验证了该方法的有效性,从而为装配研制基于单根纳米管/线的纳电子器件提供了一种新颖可行的方法。

Supermedia User Interface for Scanning Probe Microscopy

当利用扫描隧道显微镜(SPM)作为一种纳米操作工具时,由于其缺乏实时的传感器信息反馈,而大大阻碍了它的广泛应用.利用超媒体人机交互接口可以解决这个问题.在纳米操作过程中,超媒体接口不但可以为操作者提供可实时更新的仿真操作场景,还可以通过力反馈手柄让操作者实时地感受到探针受到的三维纳米操作力.除此之外,操作者还可以通过该手柄直接控制探针的三维运动.最后在聚碳酸酯上进行了超媒体人机接口的纳米刻画实验.实验结果验证了该系统的有效性和效率.

基于加速度反馈的柔性关节机械臂接触力控制

针对柔性关节机械臂从自由空间运动控制过渡到约束空间力控制的过程中,存在冲击、震荡甚至不稳定等问题,利用加速度传感器反馈控制,为柔性关节机械臂的接触力控制在较宽的带宽内提供阻尼,克服了利用单纯速度反馈控制带宽窄的局限。对柔性关节机械臂的接触力控制进行建模和基于加速度反馈的控制策略分析,并在柔性关节机械臂上进行了接触力控制的试验研究。结果表明,这种方法有效。

机器人化纳米操作中任务空间的实时反馈方法研究

纳米科技的最终目标是在原子、分子尺度上，制造具有新颖物理、化学和生物特性的器件和系统，而实现这个目标最为关键的使能技术便是纳米尺度下进行观测、操作和装配的科学方法与相关技术手段。原子力显微镜（AFM：Atomic Force Microscopy）的发明为实现这一目标提供了可行途径，AFM除了能够在常态下实现对原子、分子尺度大小物体的观测，并且由于其超高的分辨率和运动精度，可控、可重复的运动方式，独特的机械力作用机理，任意环境的可适应性而广泛应用于纳米操作。然而AFM的主要功能是进行纳米观测，应用于纳米操作时面临着许多挑战性的难题，尽管随着近十年的深入研究，一些问题已经得到了部分解决，但是缺乏高可信度的实时视觉反馈、无法实现任务空间内探针的精确定位依然阻碍着AFM纳米操作的效率。以目前最为先进的AFM纳米操作方法—增强现实技术为例，尽管该技术可以为操作者提供实时的视觉反馈，但是这种视觉反馈并不代表纳米操作场景的真实变化，而是根据离线模型计算得到的一种图形仿真，因而视觉反馈是否可信取决于模型的准确程度，然而受纳米尺度下各种非线性力的影响，如毛细力、范德华力、静电力等等，很难建立完全精确的物理模型，模型误差将导致错误的视觉反馈并引起纳米操作的失败。此外，受PZT非线性和温漂的影响，基于AFM的纳米操作还缺乏在任务空间内对探针进行精确定位的能力，导致操作过程中AFM探针无法有效接触到纳米物体，使得机器人学中“从A点运动到B点”最为基本的任务难以实现，这些缺点都严重阻碍着AFM纳米操作的效率和效果。本论文针对上述问题，以机器人学中的感知、决策、行为理论和监控方法为基础，具体开展了以下几方面的工作： 1、视觉反馈缺乏可信度是基于增强现实AFM纳米操作面临的主要问题，由于操作者无法对视觉反馈可信度作出评断，经常会在错误视觉反馈的指引下进行无效的纳米操作，从而浪费大量的时间，降低了AFM纳米操作的效率。为了克服上述问题，本文在研究信息诊断与反馈理论基础上，提出了基于Kalman滤波的视觉反馈可信度在线监控方法，实现了视觉反馈错误的实时检测，避免了无效纳米操作的发生，提高了AFM纳米操作的效率。 2、错误视觉反馈被检测出后，需要对其修正以保证纳米操作任务的成功完成。然而传统修正方法需要中断纳米操作进行重新扫描成像，这往往需要耗费几分钟的时间，严重降低了AFM纳米操作的效率。针对该问题，本文提出一种基于局部扫描的在线修正方法，通过扫描轨迹的优化，该方法能够对真实纳米操作结果进行实时感知，从而不需要中断纳米操作就能实现错误视觉反馈的修正，并使得整个修正过程对于操作者透明。这保证了实时可视监控信息的真实性，显著提升了AFM纳米操作的效率。 3、PZT非线性和随机漂移是影响AFM探针精确定位的主要因素，针对该问题本文提出了一种基于路标的探针定位方法，其核心思想是不再采用距离为测度方式进行探针位置描述，而是将作业区域的特定形貌特征定义为参考路标，通过探针对特征形貌的主动感知实现基于路标地图的探针定位，有效消除PZT非线性和随机漂移引起的定位误差，提高探针在任务空间内的定位精度。 4、研究了机器人化纳米操作系统任务空间实时反馈的构建技术，具体包括高灵敏度纳米操作力的感知方法，系统结构误差的产生原因和补偿策略，面向探针实时运动控制的系统结构设计，系统的软硬件实现方案等内容，并利用该实验平台开展了大量实验研究，验证了本论文所提出理论方法的正确性，同时演示性地组建了基于单根CNT和DNA的纳电子器件，实验结果表明AFM纳米操作的效率和效果得到了极大提升。本文的研究工作丰富了基于AFM的机器人化纳米操作理论，为基于AFM的纳米制造技术发展提供了具有一定指导意义的理论方法和研究途径。