Planejamento estatístico de experimentos como uma ferramenta para otimização das condições de biossorção de Cu(II) em batelada utilizando-se casca de nozes pecã como biossorvente

In order to reduce the total number of experiments for achieving the highest amount of adsorbed Cu2+ (qmax) using pecan nutshells (Carya illinoensis) as biosorbent, a full 2(4) factorial design with two central points was carried out (mass of biosorbent- m, pH, initial metallic ion concentration- C0, time of contact- t). In order to continue the optimization of the system, a central composite surface analysis design with two factors and five central points was carried out. The maximum amount of Cu2+ taken up by the pecan nutshells was 20 mg g-1. These results were confirmed by determining a Cu2+ isotherm using the best conditions attained by the statistical design of experiments.

Adsorção de íons cobre(II) pela quitosana usando coluna em sistema sob fluxo hidrodinâmico

The adsorption of Cu(II) ions from aqueous solution by chitosan using a column in a closed hydrodynamic flow system is described. The adsorption capacities as a function of contact time of copper(II) ions and chitosan were determined by varying the ionic strength, temperature and the flow of the metal solution. The Langmuir model reproduced the adsorption isothermal data better than the Freundlich model. The experimental kinetic data correlate properly with the second-order kinetic reaction for the whole set of experimental adsorption conditions. The rate constants exercise great influence on the time taken for equilibrium to be established by complexation or electrostatic interaction between the amino groups of chitosan and the metal.

Comparative performance of the stable isotope signatures of carbon, nitrogen and oxygen in assessing early vigour and grain yield in durum wheat

The present paper studied the performance of the stable isotope signatures of carbon (δ13C), nitrogen (δ15N) and oxygen (δ18O) in plants when used to assess early vigour and grain yield (GY) in durum wheat growing under mild and moderate Mediterranean stress conditions. A collection of 114 recombinant inbred lines was grown under rainfed (RF) and supplementary irrigation (IR) conditions. Broad sense heritabilities (H2) for GY and harvest index (HI) were higher under RF conditions than under IR. Broad sense heritabilities for δ13C were always above 0·60, regardless of the plant part studied, with similar values for IR and RF trials. Some of the largest genetic correlations with GY were those shown by the δ13C content of the flag leaf blade and mature grains. Under both water treatments, mature grains showed the highest negative correlations between δ13C and GY across genotypes. Flag leaf δ13C was negatively correlated with GY only under RF conditions. The δ13C in seedlings was negatively correlated, under IR conditions only, with GY but also with early vigour. The sources of variation in early vigour were studied by stepwise analysis using the stable isotope signatures measured in seedlings. The δ13C was able to explain almost 0·20 of this variation under RF, but up to 0·30 under IR. In addition, nitrogen concentration in seedlings accounted for another 0·05 of variation, increasing the amount explained to 0·35. The sources of variation in GY were also studied through stable isotope signatures and biomass of different plant parts: δ13C was always the first parameter to appear in the models for both water conditions, explaining c. 0·20 of the variation. The second parameter (δ15N or N concentration of grain, or biomass at maturity) depended on the water conditions and the plant tissue being analysed. Oxygen isotope composition (δ18O) was only able to explain a small amount of the variation in GY. In this regard, despite the known and previously described value of δ13C as a tool in breeding, δ15N is confirmed as an additional tool in the present study. Oxygen isotope composition does not seem to offer any potential, at least under the conditions of the present study.

Invasive populations of Senecio pterophorus are neither more productive nor more plastic than the native populations

Successful plant invaders may have specific morphological and physiological traits that promote invasion in a new habitat. The Evolution of Increased Competitive Ability (EICA) hypothesis predicts that plants released from natural enemies in the introduced habitats are more competitive and perform better than plants from the native populations. An increased phenotypic plasticity may also favour invasion because it allows plants to function under a wider range of environments. In this study we used Senecio pterophorus (Asteraceae) to test whether introduced plant populations are 1)more competitive and 2) more plastic compared with the native populations. We conducted a common garden experiment using plants from the native range (South Africa, Eastern Cape), an expanded range (South Africa, Western Cape) and two introduced ranges (Australia and Europe) under different conditions of water availability. Contrary to the EICA and the increased plasticity hypotheses, plants from the invasive and expanded populations grew less and responded less to watering than those from their native range. These results may be caused by a depleted competition as well as the presence of genetic bottlenecks in the newly invaded areas.

Development and validation of a novel stability indicating RP-UPLC method for simultaneous determination of nizatidine, methylparaben and propylparaben in oral liquid pharmaceutical formulation

A selective and accurate stability-indicating gradient reverse phase ultra performance liquid chromatographic method has been developed and validated for the simultaneous determination of nizatidine, methylparaben and propylparaben in pharmaceutical oral liquid formulation. The separation was achieved on Acquity UPLC TM HSS T3 1.8 µm column by using mobile phase containing a gradient mixture of solvent A (0.02 Mol L-1 KH2PO4, pH 7.5) and B (60:40 v/v mixture of methanol and acetonitrile) at flow rate of 0.4 mL min-1. Drug product was exposed to the stress conditions of oxidative, acid, base, hydrolytic, thermal and photolytic degradation. The developed method was validated as per international ICH guidelines with respect to specificity, linearity, accuracy, precision and robustness.

Enzymatic activity of catechol 1,2-dioxygenase and catechol 2,3-dioxygenase produced by Gordonia polyisoprenivorans

This study aimed to evaluate the environmental conditions for enzyme activity of catechol 1,2-dioxygenase (C1,2O) and catechol 2,3-dioxygenase (C2,3O) produced by Gordonia polyisoprenivorans in cell-free and immobilized extracts. The optimum conditions of pH, temperature, time course and effect of ions for enzyme activity were determined. Peak activity of C1,2O occurred at pH 8.0. The isolate exhibited the highest activity of C2,3O at pH 7.0 and 8.0 for the cell-free extract and immobilized extract, respectively. This isolate exhibited important characteristics such as broad range of pH, temperature and time course for enzyme activity.

MICROWAVE ACTIVATION OF IMMOBILIZED LIPASE FOR TRANSESTERIFICATION OF VEGETABLE OILS

This work investigated the effect of microwave irradiation (MW) on the ethanolysis rate of soybean and sunflower oils catalyzed by supported Novozyme 435 (Candida antarctica). The effects of tert-butanol, water addition and oil:ethanol molar ratio on transesterification were evaluated under conventional heating (CH), and under optimum reaction conditions (with no added water in the system, 10% tert-butanol and 3:1 ethanol-to-oil molar ratio). The reactions were monitored up to 24 h to determine the conditions of initial reaction velocity. The investigated variables under MW (50 W) were: reaction time (5.0-180 min) and mode of reactor operation (fixed power, dynamic and cycles) in the absence and presence of tert-butanol (10% (w/w). The measured response was the reaction conversion in ethyl esters, which was linked to the enzyme catalytic activity. The results indicated that the use of microwave improved the activity at fixed power mode. A positive effect of the association of tert-butanol and MW irradiation on the catalytic activity was observed. The reaction rate improved in the order of approximately 1.5 fold compared to that under CH with soybean oil. Using soybean oil, the enzymatic transesterification under MW for conversion to FAEE (fatty acid ethyl esters) reached >99% in 3h, while with the use of CH the conversions were about 57% under similar conditions.

NANOPARTICLES OF TUNGSTEN AS LOW-COST MONOMETALLIC CATALYST FOR SELECTIVE HYDROGENATION OF 3-HEXYNE

Low-cost tungsten monometallic catalysts containing variable amounts of metal (4.5, 7.1 and 8.5%W) were prepared by impregnating alumina with ammonium metatungstate as an inexpensive precursor. The catalysts were characterized using ICP, XPS, XRD, TPR and hydrogen chemisorption. These techniques revealed mainly WO3-Al2O3 (W6+) species on the surface. The effects of the content of W nanoparticles and reaction temperature on activity and selectivity for the partial hydrogenation of 3-hexyne, a non-terminal alkyne, were assessed under moderate conditions of temperature and pressure. The monometallic catalysts prepared were found to be active and stereoselective for the production of (Z )-3-hexene, had the following order: 7.1WN/A > 8.5 WN/A ≥ 4.5 WN/A. Additionally, the performance of the synthesized xWN/A catalysts exhibited high sensitivity to temperature variation. In all cases, the maximum 3-hexyne total conversion and selectivity was achieved at 323 K. The performance of the catalysts was considered to be a consequence of two phenomena: a) the electronic effects, related to the high charge of W (+6), causing an intensive dipole moment in the hydrogen molecule (van der Waals forces) and leading to heterolytic bond rupture; the H+ and H- species generated approach a 3-hexyne adsorbate molecule and cause heterolytic rupture of the C≡C bond into C- = C+; and b) steric effects related to the high concentration of WO3 on 8.5WN/A that block the Al2O3 support. Catalyst deactivation was detected, starting at about 50 min of reaction time. Electrodeficient W6+ species are responsible for the formation of green oil at the surface level, blocking pores and active sites of the catalyst, particularly at low reaction temperatures (293 and 303 K). The resulting best catalyst, 7.1WN/A, has low fabrication cost and high selectivity for (Z )-3-hexene (94%) at 323 K. This selectivity is comparable to that of the classical and more expensive industrial Lindlar catalyst (5 wt% Pd). The alumina supported tungsten catalysts are low-cost potential replacements for the Lindlar industrial catalyst. These catalysts could also be used for preparing bimetallic W-Pd catalysts for selective hydrogenation of terminal and non-terminal alkynes.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Estimation of existing cable systems in generator-busbar unit and choice the optimal solution for its modernization

The aim of this master’s thesis is to develop an algorithm to calculate the cable network for heat and power station CHGRES. This algorithm includes important aspect which has an influence on the cable network reliability. Moreover, according to developed algorithm, the optimal solution for modernization cable system from economical and technical point of view was obtained. The conditions of existing cable lines show that replacement is necessary. Otherwise, the fault situation would happen. In this case company would loss not only money but also its prestige. As a solution, XLPE single core cables are more profitable than other types of cable considered in this work. Moreover, it is presented the dependence of value of short circuit current on number of 10/110 kV transformers connected in parallel between main grid and considered 10 kV busbar and how it affects on final decision. Furthermore, the losses of company in power (capacity) market due to fault situation are presented. These losses are commensurable with investment to replace existing cable system.

Simulation of hydrogen peroxide direct synthesis in a microreactor

A set of models in Aspen plus was built to simulate the direct synthesis process of hydrogen peroxide in a micro-reactor system. This process model can be used to carry out material balance calculation under various experimental conditions. Three thermodynamic property methods were compared by calculating gas solubility and Uniquac-RK method was finally selected for process model. Two different operation modes with corresponding operation conditions were proposed as the starting point of future experiments. Simulations for these two modes were carried out to get the information of material streams. Moreover, some hydrodynamic parameters such as gas/liquid superficial velocity, gas holdup were also calculated with improved process model. These parameters proved the proposed experimental conditions reasonable to some extent. The influence of operation conditions including temperature, pressure and circulation ratio was analyzed for the first operation mode, where pure oxygen was fed into dissolving tank and hydrogen-carbon dioxide mixture was fed into microreactor directly. The preferred operation conditions for the system are low temperature (2°C) and high pressure (30 bar) in dissolving tank. High circulation ratio might be good in the sense that more oxygen could be dissolved and fed into reactor for reactions, but meanwhile hydrodynamics of microreactor should be considered. Furthermore, more operation conditions of reactor gas/liquid feeds in both of two operation modes were proposed to provide guidance for future experiment design and corresponding hydrodynamic parameters were also calculated. Finally, safety issue was considered from thermodynamic point of view and there is no explosion danger at given experimental plan since the released reaction heat will not cause solvent vaporization inside the microchannels. The improvement of process model still needs further study based on the future experimental results.

Online Ultrasound Measurements of Membrane Compaction

There are several filtration applications in the pulp and paper industry where the capacity and cost-effectiveness of processes are of importance. Ultrafiltration is used to clean process water. Ultrafiltration is a membrane process that separates a certain component or compound from a liquid stream. The pressure difference across the membrane sieves macromolecules smaller than 0.001-0.02 μm through the membrane. When optimizing the filtration process capacity, online information about the conditions of the membrane is needed. Fouling and compaction of the membrane both affect the capacity of the filtration process. In fouling a “cake” layer starts to build on the surface of the membrane. This layer blocks the molecules from sieving through the membrane thereby decreasing the yield of the process. In compaction of the membrane the structure is flattened out because of the high pressure applied. The higher pressure increases the capacity but may damage the structure of the membrane permanently. Information about the compaction is needed to effectively operate the filters. The objective of this study was to develop an accurate system for online monitoring of the condition of the membrane using ultrasound reflectometry. Measurements of ultrafiltration membrane compaction were made successfully utilizing ultrasound. The results were confirmed by permeate flux decline, measurements of compaction with a micrometer, mechanical compaction using a hydraulic piston and a scanning electron microscope (SEM). The scientific contribution of this thesis is to introduce a secondary ultrasound transducer to determine the speed of sound in the fluid used. The speed of sound is highly dependent on the temperature and pressure used in the filters. When the exact speed of sound is obtained by the reference transducer, the effect of temperature and pressure is eliminated. This speed is then used to calculate the distances with a higher accuracy. As the accuracy or the resolution of the ultrasound measurement is increased, the method can be applied to a higher amount of applications especially for processes where fouling layers are thinner because of smaller macromolecules. With the help of the transducer, membrane compaction of 13 μm was measured in the pressure of 5 bars. The results were verified with the permeate flux decline, which indicated that compaction had taken place. The measurements of compaction with a micrometer showed compaction of 23–26 μm. The results are in the same range and confirm the compaction. Mechanical compaction measurements were made using a hydraulic piston, and the result was the same 13 μm as obtained by applying the ultrasound time domain reflectometry (UTDR). A scanning electron microscope (SEM) was used to study the structure of the samples before and after the compaction.

Prevalence of Lettuce mosaic virus - common strain on three lettuce producing areas from São Paulo State

LMV is one of the most important pathogens of lettuce worldwide. Based on their ability to overcome the resistance genes mo1¹ and mo1² in lettuce, isolates can be divided in two types: LMV-Most, which can infect and are seed-borne in cultivars containing the mo1 gene and LMV-Common, which do not cause symptoms on these cultivars and are seed transmitted only in susceptible cultivars. To evaluate the occurrence of these two types of LMV isolates, a survey was carried out during 2002-2005 in three lettuce production areas from São Paulo State. Total RNA was used for the diagnosis of LMV isolates by RT-PCR using universal primers for the variable N-terminus of the capsid protein, in the 3' end of the genome. Positives samples were analyzed by a second RT-PCR using specifics primers for LMV-Most isolates designed to amplify a fragment from the central region (CI-VPg) of the genome. A total of 1362 samples showing mosaic symptoms were collected and 504 (37.29 %) were positives for LMV. On susceptible lettuce cultivars, LMV-Common was prevalent (77.3%). LMV-Most was found frequently associated with tolerant (mo1¹) lettuce cultivars. Susceptible cultivars correspond today for most of the area of lettuce production. So, despite the ability of LMV-Most isolates to overcome the resistance provided by the recessive mo1¹ gene, they are not prevalent in the conditions of São Paulo State.

Hållpunkter för lärande : småbarns möten

Developed from human activities, mathematical knowledge is bound to the world and cultures that men and women experience. One can say that mathematics is rooted in humans’ everyday life, an environment where people reach agreement regarding certain “laws” and principles in mathematics. Through interaction with worldly phenomena and people, children will always gain experience that they can then in turn use to understand future situations. Consequently, the environment in which a child grows up plays an important role in what that child experiences and what possibilities for learning that child has. Variation theory, a branch of phenomenographical research, defines human learning as changes in understanding and acting towards a specific phenomenon. Variation theory implies a focus on that which it is possible to learn in a specific learning situation, since only a limited number of critical aspects of a phenomenon can be simultaneously discerned and focused on. The aim of this study is to discern how toddlers experience and learn mathematics in a daycare environment. The study focuses on what toddlers experience, how their learning experience is formed, and how toddlers use their understanding to master their environment. Twenty-three children were observed videographically during everyday activities. The videographic methodology aims to describe and interpret human actions in natural settings. The children are aged from 1 year, 1 month to 3 years, 9 months. Descriptions of the toddlers’ actions and communication with other children and adults are analyzed phenomenographically in order to discover how the children come to understand the different aspects of mathematics they encounter. The study’s analysis reveals that toddlers encounter various mathematical concepts, similarities and differences, and the relationship between parts and whole. Children form their understanding of such aspects in interaction with other children and adults in their everyday life. The results also show that for a certain type of learning to occur, some critical conditions must exist. Variation, simultaneity, reasonableness and fixed points are critical conditions of learning that appear to be important for toddlers’ learning. These four critical conditions are integral parts of the learning process. How children understand mathematics influences how they use mathematics as a tool to master their surrounding world. The results of the study’s analysis of how children use their understanding of mathematics shows that children use mathematics to uphold societal rules, to describe their surrounding world, and as a tool for problem solving. Accordingly, mathematics can be considered a very important phenomenon that children should come into contact with in different ways and which needs to be recognized as a necessary part of children’s everyday life. Adults working with young children play an important role in setting perimeters for children’s experiences and possibilities to explore mathematical concepts and phenomena. Therefore, this study is significant as regards understanding how children learn mathematics through everyday activities.

Biocontrol of Sclerotinia sclerotiorum and white mold of soybean using saprobic fungi from semi-arid areas of Northeastern Brazil

ABSTRACTThe incidence and the levels of yield loss caused by the white mold of soybean (caused by the fungus Sclerotinia sclerotiorum) have increased in areas of higher altitude at Cerrado and Southern Brazil, causing yield losses of up to 60%. The aim of this study was to select saprobic fungi with the potential to control the white mold of soybean. First, in vitroantagonism screening was carried out to test eight saprobic fungi against S. sclerotiorum. Assessment of S. sclerotiorum mycelial growth was done at four and seven days after its placement on the culture medium. The isolate showing greatest antagonistic effect in all tests/assessments was Myrothecium sp. An in vivo experiment was conducted in a greenhouse and growth chamber, where plants previously treated with eight saprobic fungi were artificially inoculated with S. sclerotiorum. The fungal culture medium (potato-dextrose) and the commercial resistance inducer acibenzolar-S-methyl were used as controls. In the in vivotests, severity of the white mold was assessed at 8, 14 and 21 days after inoculation. The highest reduction percentage in the lesion length was observed for the treatment with Myrothecium sp. (70%), which has the greater potential to be used as biocontrol agent of soybean under the conditions of this experiment.