Structural and electrochemical characteristics of Mg((55-x))Ti(x)Ni((45-y))Pt(y) metal hydride electrodes

In recent years, Mg-Ni-based metastable alloys have been attracting attention due to their large hydrogen sorption capacities, low weight, low cost, and high availability. Despite the large discharge capacity and high activity of these alloys, the accelerated degradation of the discharge capacity after only few cycles of charge and discharge is the main shortcoming against their commercial use in batteries. The addition of alloying elements showed to be an effective way of improving the electrode performance of Mg-Ni-based alloys. In the present work, the effect of Ti and Pt alloying elements on the structure and electrode performance of a binary Mg-Ni alloy was investigated. The XRD and HRTEM revealed that all the investigated alloy compositions had multi-phase nanostructures, with crystallite size in the range of 6 nm. Moreover, the investigated alloying elements demonstrated remarkable improvements of both maximum discharge capacity and cycling life. Simultaneous addition of Ti and Pd demonstrated a synergetic effect on the electrochemical properties of the alloy electrodes. Among the investigated alloys, the best electrochemical performance was obtained for the Mg(51)Ti(4)Ni(43)Pt(2) composition (in at.%), which achieved 448 mAh g(-1) of maximum discharge capacity and retained almost 66% of this capacity after 10 cycles. In contrast, the binary Mg(55)Ni(45) alloy achieved only 248 mAh g(-1) and retained 11% of this capacity after 10 cycles. (C) 2010 Elsevier By. All rights reserved.

Phenolic matrices and sisal fibers modified with hydroxy terminated polybutadiene rubber: Impact strength, water absorption, and morphological aspects of thermosets and composites

The aim of the present work was to investigate the toughening of phenolic thermoset and its composites reinforced with sisal fibers, using hydroxyl-terminated polybutadiene rubber (HTPB) as both impact modifier and coupling agent. Substantial increase in the impact strength of the thermoset was achieved by the addition 10% of HTPB. Scanning electron microscopy (SEM) images of the material with 15% HTPB content revealed the formation of some rubber aggregates that reduced the efficiency of the toughening mechanism. In composites, the toughening effect was observed only when 2.5% of HTPB was added. The rubber aggregates were found located mainly at the matrix-fiber interface suggesting that HTPB could be used as coupling agent between the sisal fibers and the phenolic matrix. A composite reinforced with sisal fibers pre-impregnated with HTPB was then prepared; its SEM images showed the formation of a thin coating of HTPB on the surface of the fibers. The ability of HTBP as coupling agent between sisal fibers and phenolic matrix was then investigated by preparing a composite reinforced with sisal fibers pre-treated with HTPB. As revealed by its SEM images, the HTPB pre-treatment of the fibers resulted on the formation of a thin coating of HTPB on the surface of the fibers, which provided better compatibility between the fibers and the matrix at their interface, resulting in a material with low water absorption capacity and no loss of impact strength. (C) 2009 Elsevier B.V. All rights reserved.

Tribological Testing of Some Potential PVD and CVD Coatings for Steel Wire Drawing Dies

Cemented carbide is today the most frequently used drawing die material in steel wire drawing applications. This is mainly due to the possibility to obtain a broad combination of hardness and toughness thus meeting the requirements concerning strength, crack resistance and wear resistance set by the wire drawing process. However, the increasing cost of cemented carbide in combination with the possibility to increase the wear resistance of steel through the deposition of wear resistant CVD and PVD coatings have enhanced the interest to replace cemented carbide drawing dies with CVD and PVD coated steel wire drawing dies. In the present study, the possibility to replace cemented carbide wire drawing dies with CVD and PVD coated steel drawing dies have been investigated by tribological characterisation, i.e. pin-on-disc and scratch testing, in combination with post-test observations of the tribo surfaces using scanning electron microscopy, energy dispersive X-ray spectroscopy and 3D surface profilometry. Based on the results obtained, CVD and PVD coatings aimed to provide improved tribological performance of steel wire drawing dies should display a smooth surface topography, a high wear resistance, a high fracture toughness (i.e. a high cracking and chipping resistance) and intrinsic low friction properties in contact with the wire material. Also, the steel substrate used must display a sufficient load carrying capacity and resistance to thermal softening. Of the CVD and PVD coatings evaluated in the tribological tests, a CVD TiC and a PVD CrC/C coating displayed the most promising results.

Russian Arctic Ports : Problems with the development and management of tourist flows

The potential changes to the territory of the Russian Arctic open up unique possibilities for the development of tourism. More favourable transport opportunities along the Northern Sea Route (NSR) create opportunities for tourism development based on the utilisation of the extensive areas of sea shores and river basins. A major challenge for the Russian Arctic sea and river ports is their strong cargo transport orientation originated by natural resource extraction industries. A careful assessment of the prospects of current and future tourism development is presented here based on the development of regions located along the shores of the Arctic ocean (including Murmansk and Arkhangelsk oblast, Nenets Autonomous okrug (AO), Yamal-Nenets AO, Taymyr AO, Republic of Sakha, Chykotsky AO). An evaluation of the present development of tourism in maritime cities suggests that a considerable qualitative and quantitative increase of tourism activities organised by domestic tourism firms is made virtually impossible. There are several factors contributing to this. The previously established Soviet system of state support for the investments into the port facilities as well as the sea fleet were not effectively replaced by creation of new structures. The necessary investments for reconstruction could be contributed by the federal government but the priorities are not set towards the increased passenger transportation. Having in mind, increased environmental pressures in this highly sensitive area it is especially vital to establish a well-functioning monitoring and rescue system in the situation of ever increasing risks which come not only from the increased transports along the NSR, but also from the exploitation of the offshore oil and gas reserves in the Arctic seas. The capacity and knowledge established in Nordic countries (Norway, Finland) concerning cruise tourism should not be underestimated and the already functioning cooperation in Barents Region should expand towards this particular segment of the tourism industry. The current stage of economic development in Russia makes it clear that tourism development is not able to compete with the well-needed increase in the cargo transportation, which means that Russia’s fleet is going to be utilised by other industries. However, opening up this area to both local and international visitors could contribute to the economic prosperity of these remote areas and if carefully managed could sustain already existing maritime cities along the shores of the Arctic Ocean.

Evaluating And Optimizing Sustainable Drainage Design To Maximize Multiple Benefits: Case Studies In China

In the past, the focus of drainage design was on sizing pipes and storages in order to provide sufficient network capacity. This traditional approach, together with computer software and technical guidance, had been successful for many years. However, due to rapid population growth and urbanisation, the requirements of a “good” drainage design have also changed significantly. In addition to water management, other aspects such as environmental impacts, amenity values and carbon footprint have to be considered during the design process. Going forward, we need to address the key sustainability issues carefully and practically. The key challenge of moving from simple objectives (e.g. capacity and costs) to complicated objectives (e.g. capacity, flood risk, environment, amenity etc) is the difficulty to strike a balance between various objectives and to justify potential benefits and compromises. In order to assist decision makers, we developed a new decision support system for drainage design. The system consists of two main components – a multi-criteria evaluation framework for drainage systems and a multi-objective optimisation tool. The evaluation framework is used for the quantification of performance, life-cycle costs and benefits of different drainage systems. The optimisation tool can search for feasible combinations of design parameters such as the sizes, order and type of drainage components that maximise multiple benefits. In this paper, we will discuss real-world application of the decision support system. A number of case studies have been developed based on recent drainage projects in China. We will use the case studies to illustrate how the evaluation framework highlights and compares the pros and cons of various design options. We will also discuss how the design parameters can be optimised based on the preferences of decision makers. The work described here is the output of an EngD project funded by EPSRC and XP Solutions.

Online and Hybrid Course Prioritization Guide: 10 Strategies for Promoting Enrollment Growth and Student Success

Institutions of all shapes and sizes are investing significant sums to expand their portfolio of online and hybrid courses without specific institutional priorities in mind, often resulting in a mix of arbitrary, sub-scale offerings. This creates an unsustainably expensive disconnect between the institution’s online portfolio (largely steered by unit-level interests and capacity) and its overarching interest in using technology to increase access, improve student success, and grow revenue. This guide is designed to help institutional leaders prioritize scarce resources devoted to online and hybrid course development toward the most promising available opportunities. By targeting specific curricular "gaps," institutions can improve retention, reduce time-to-degree, regain or expand their share of currently enrolled student credit hours, or even attract new students to existing programs.

Courts as healthcare policy-makers: the problem, the responses to the problem and problems in the responses

This article starts by analysing healthcare litigation in Brazil by means of a literature review of articles that contribute with empirical findings on this phenomenon. Based on this review, I argue that health care litigation in Brazil makes the public health system less fair and rational. In the second part of this article, I discuss the three most overarching responses to control the level of litigation and its impact on the public health system: (i) the public hearing held by the Supreme Federal Court and the criteria the court established thereafter; (ii) the recommendations by the National Council of Justice aimed at building courts’ institutional capacity; and (iii) the enactment of the Federal Law 12.401/11, which created a new health technology assessment system. I argue that latter is the best response because it keeps the substantive decisions on the allocation of healthcare resources in the institution that is in the best position to make them. Moreover, this legislation will make the decisions about provision of health treatments more explicit, making easier for courts to control the procedure and the reasons for these decisions.

In-depth search focused on furans, lactones, volatile phenols, and acetals as potential age markers of Madeira wines by comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry combined with solid phase microextraction

The establishment of potential age markers of Madeira wine is of paramount significance as it may contribute to detect frauds and to ensure the authenticity of wine. Considering the chemical groups of furans, lactones, volatile phenols, and acetals, 103 volatile compounds were tentatively identified; among these, 71 have been reported for the first time in Madeira wines. The chemical groups that could be used as potential age markers were predominantly acetals, namely, diethoxymethane, 1,1-diethoxyethane, 1,1-diethoxy-2-methyl-propane, 1-(1-ethoxyethoxy)-pentane, trans-dioxane and 2-propyl-1,3-dioxolane, and from the other chemical groups, 5-methylfurfural and cis-oak-lactone, independently of the variety and the type of wine. GC × GC-ToFMS system offers a more useful approach to identify these compounds compared to previous studies using GC−qMS, due to the orthogonal systems, that reduce coelution, increase peak capacity and mass selectivity, contributing to the establishment of new potential Madeira wine age markers. Remarkable results were also obtained in terms of compound identification based on the organized structure of the peaks of structurally related compounds in the GC × GC peak apex plots. This information represents a valuable approach for future studies, as the ordered-structure principle can considerably help the establishment of the composition of samples. This new approach provides data that can be extended to determine age markers of other types of wines.

Knowledge of the patients regarding leprosy and adherence to treatment

Leprosy is a chronic infectious disease caused by Mycobacterium leprae. It is known for its great disfiguring capacity and is considered an extremely serious disease to public health worldwide. The state of Ceará ranks 13th in number of cases of leprosy in Brazil, and fourth in Northeastern region, with an average of 2,149 new cases diagnosed every year. This study aimed to evaluate the knowledge of leprosy patients regarding treatment, and to assess the level of treatment adherence and its possible barriers. The study was conducted in the reference center for dermatology, from September 2010 to October 2010, in Fortaleza, Ceará. The study data were collected by means of a structured interview, along with the Morisky-Green test, in order to assess treatment adherence and barriers to adherence. A total of 70 patients were interviewed, out of whom 66 were new cases. The majority of patients were between 42 and 50 years old, and 37 (52.9%) were male. Most patients were clinically classified as presentingmultibacillary leprosy (80%), and 78.6% of them were from Fortaleza, Brazil. The Morisky-Green test indicated that 62.9% of patients presented a low level of adherence (p < 0.005), despite claiming to aware of the disease risks. However, it was observed that 57.1% of the patients had no difficulty adhering to treatment, while 38.6% reported little difficulty. This study shows that despite the patients claiming to be familiar with leprosy and its treatment, the Morisky-Green test clearly demonstrated that they actually were not aware of the principles of therapy, which is evidenced by the low degree of treatment adherence

Eficácia do treinamento de força sobre parâmetros cardiovasculares e antropométricos em adultos sedentários

This study aimed to determine the influence of strength training (ST), in three weekly sessions over ten weeks, on cardiovascular parameters and anthropometric measurements. It is a before and after intervention trial, with a sample composed of 30 individuals. Participants were adults aged between 18 and 40 years, from both sexes and sedentary for at least three months previously. Tests were computed ergospirometry, CRP, PWV and body composition (dependent variables) before and after the experiment. Independent variables, age and sex, were considered in order to determine their influence on the dependent variablesevaluatedend. By comparing the initial cardiovascular parameters with those obtained after intervention in patients undergoing the ST proposed (a Student s t-test was conducted within each group for samples matched to parameters with normal distribution, while the Wilcoxin was applied for those without), there was no significant difference in PWV(p =0469) or PCR(p =0.247), but there was an increase in anaerobic threshold(AT) (p=0.004) and Maximal Oxygen Uptake(VO2max) (p =0.052). In regard to anthropometric measures, individuals significantly reduced their body fat percentage (p<0.001) and fat mass (p<0,001), as well as increasing lean mass (p<0.001). However, no changes were recorded in the waist-to-hip ratio (WHR) (p= 0.777), body mass (p=0.226) or body mass index (BMI) (p =0.212). Findings of this study lead us to believe that the proposed ST, and did not increase the VOP or PCR improves cardiorespiratory capacity and body composition. Devotees of this training can therefore safely enjoy all its benefits without risk to the cardiovascular system

Hemograma e perfil bioquímico sérico, inclusive hemogasométrico, de bezerros infectados experimentalmente com Salmonella Dublin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aspectos clínicos e concentração sérica da creatina-quinase e lactato-desidrogenase em cães submetidos à fisioterapia após atrofia muscular induzida

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Subdosages of Bacillus thuringiensis on Plutella xylostella) (Lepepidoptera: plutellidae) and Trichogramma pretiosum (Hymenoptera: trichogrammatidae)

The aim of this paper was to evaluate the biological aspects of Plutella xylostella and Trichogramma pretiosum in eggs of the F2 generation of P. xylostella under the influence of Bacillus thuringiensis in laboratory conditions. The experiment was conducted in the Laboratorio de Biologia and Criacao de Insetos of Faculdade de Ciencias Agrarias e Veterinarias de Jaboticabal - UNESP reen collars contaminated with strains and commercial product based on B. thuringiensis in the laboratory. The eggs obtained from the F2 generation of P. xylostella evaluated the biological parameters of T. pretiosum. It was observed that some biological characteristics of P. xylostella showed changes by the treatment with B. thuringiensis. The viability of the larvae and pupae stages, pupae weight were the biological parameters more influenced by treatments, with values significantly reduced when compared to control. However, the larvae length and pupae stages and sex ratio were similar in all treatments, with no significant biological variations. Thus, this bacterium isolated from this behavior may provide greater exposure of larvae to other natural enemies as well as generation of adults less viable, which makes them potential programs in pest control, since the interaction of the methods of control is one of the main ways to enhance the biological control of insect pests. It was observed sublethal effects on P. xylostella biology, and B. thuringiensis negative influence on the parasitism capacity and emergency of T. pretiosum.

Composição de fibras musculares esqueléticas de eqüinos jovens da raça Brasileiro de Hipismo

The aim of this study was to typify the skeletal striated fibers of the gluteus medius muscle of young Brasileiro de Hipismo (BH) horses by means of histochemical analysis with m-ATPase and NADH-TR according to the sex and the biopsy depth. It was observed that the frequency (F;%) and the relative cross sectional area (RCSA;%) of the fibers type IIX were greater than the fibers type IIA, which F and RCSA were greater than the fibers type I. The comparison between sex and muscles depht, showed no significant difference in F and RCSA in the three types of fibers. The results of morphometry showed that the gluteus medius muscle has greater glycolitic metabolism and anaerobic capacity because of the presence of large proportion of type IIX fibers. This may be justified by the genetic influence of Thoroughbred in the formation of Brasileiro de Hipismo breed.

Sucrose and nitrogen supplies regulate growth of maize kernels

The growth of maize (Zea mays L.) kernels depends on the availability of carbon (C) and nitrogen (N) assimilates supplied by the mother plant and the capacity of the kernel to use them. Our objectives were to study the effects of N and sucrose supply levels on growth and metabolism of maize kernels. Kernel explants of Pioneer 34RO6 were cultured in vitro with varying combinations of N (5 to 30 mM) and sucrose (117 to 467 mM). Maximum kernel growth was obtained with 10 mM N and 292 mM sucrose in the medium, and a deficiency of one assimilate could not be overcome by a sufficiency of the other. Increasing the N supply led to increases in the kernel sink capacity (number of cells and starch granules in the endosperm), activity of certain enzymes (soluble and bound invertases, sucrose synthase, and aspartate aminotransaminase), starch, and the levels of N compounds (total-N, soluble protein, and free amino acids), and decreased the levels of C metabolites (sucrose and reducing sugars). Conversely, increasing the sucrose supply increased the level of endosperm C metabolites, free amino acids, and ADPG-PPase and alanine transaminase activities, but decreased the activity of soluble invertase and concentrations of soluble protein and total-N. Thus, while C and N are interdependent and essential for accumulation of maximum kernel weight, they appear to regulate growth by different means. Nitrogen supply aids the establishment of kernel sink capacity, and promotes activity of enzymes relating to sucrose and nitrogen uptake, while sucrose regulates the activities df invertase and ADPG-PPase. (C) 1999 Annals of Botany Company.