Nanoscale effects and applications of self-organized nanostructured thin films

A nanostructured thin film is a thin material layer, usually supported by a (solid) substrate, which possesses subdomains with characteristic nanoscale dimensions (10 ~ 100 nm) that are differentiated by their material properties. Such films have captured vast research interest because the dimensions and the morphology of the nanostructure introduce new possibilities to manipulating chemical and physical properties not found in bulk materials. Block copolymer (BCP) self-assembly, and anodization to form nanoporous anodic aluminium oxide (AAO), are two different methods for generating nanostructures by self-organization. Using poly(styrene-block-methyl methacrylate) (PS-b-PMMA) nanopatterned thin films, it is demonstrated that these polymer nanopatterns can be used to study the influence of nanoscale features on protein-surface interactions. Moreover, a method for the directed assembly of adsorbed protein nanoarrays, based on the nanoscale juxtaposition of the BCP surface domains, is also demonstrated. Studies on protein-nanopattern interactions may inform the design of biomaterials, biosensors, and relevant cell-surface experiments that make use of nanoscale structures. In addition, PS-b-PMMA and AAO thin films are also demonstrated for use as optical waveguides at visible wavelengths. Due to the sub-wavelength nature of the nanostructures, scattering losses are minimized, and the optical response is amenable to analysis with effective medium theory (EMT). Optical waveguide measurements and EMT analysis of the films’ optical anisotropy enabled the in situ characterization of the PS-b-PMMA nanostructure, and a variety of surface processes within the nanoporous AAO involving (bio)macromolecules at high sensitivity.

Mixtures of colloidal rods and spheres in bulk and in confinement

When non-adsorbing polymers are added to an isotropic suspension of rod-like colloids, the colloids effectively attract each other via depletion forces. Monte Carlo simulations were performed to study the phase diagram of such rod-polymer mixtures. The colloidal rods were modelled as hard spherocylinders; the polymers were described as spheres of the same diameter as the rods. The polymers may overlap with no energy cost, while overlap of polymers and rods is forbidden. In this thesis the emphasis was on the depletion effects caused by the addition of spheres on the isotropic phase of rod-like particles. Although most of the present experimental studies consider systems close to or beyond the isotropic-nematic transition, the isotropic phase with depletion interactions turns out to be a not less interesting topic. First, the percolation problem was studied in canonical simulations of a system of hard rods and soft spheres, where the amount of depletant was kept low to prevent phase separation of the mixture. The lowering of the percolation threshold seen in experiment is confirmed to be due to the depletion interactions. The local changes in the structure of the fluid of rods, which were measured in the simulations, indicated that the depletion forces enhance local alignment and aggregation of the rods. Then, the phase diagram of isotropic-isotropic demixing of short spherocylinders was calculated using grand canonical ensemble simulations with successive umbrella sampling. Finite size scaling analysis allowed to estimate the location of the critical point. Also, estimates for the interfacial tension between the coexisting isotropic phases and analyses of its power-law behaviour on approach of the critical point are presented. The obtained phase diagram was compared to the predictions of the free volume theory. After an analysis of the bulk, the phase behaviour in confinement was studied. The critical point of gas-liquid demixing is shifted to higher concentrations of rods and smaller concentrations of spheres due to the formation of an orientationally ordered surface film. If the separation between the walls becomes very small, the critical point is shifted back to smaller concentrations of rods because the surface film breaks up. A method to calculate the contact angle of the liquid-gas interface with the wall is introduced and the wetting behaviour on the approach to the critical point is analysed.

Pollen-placement and pollen-portioning in diverse Salvia-species

This dissertation addresses the staminal lever mechanism of the genus Salvia. Various hypotheses referring to its purpose and function are tested and elucidated. The first hypothesis maintains that the lever is a mechanical selection mechanism which excludes weak pollinators from the flower. This hypothesis is refuted and the respective results of force measurements and morphological investigations are presented, statistically evaluated and discussed. The force measurements and morphological investigations were conducted on the staminal levers and flowers of 8 bee pollinated (melittophilous) and 6 bird pollinated (ornithophilous) species. For comparison a ninth melittophilous species that lacks the staminal lever was investigated. In this species the force measurements were conducted on floral structures that were suspected to hinder a flower visitor. The hypotheses, which state that the staminal lever is a tool for pollen portioning and reduces the risk of pollen loss as well as hybridisation due to its ability to perform a repeatable, accurate and species-specific pollen placement on a wide range of diverse pollinators, are confirmed. Investigations with respect to pollen portioning were carried out on 13 sages. The lever mechanism can be released several times in a row, while the pollen sacs leave a dosed pollen portion on a well defined spot on the pollinator‘s body. Pollen placement was investigated for 12 sages. In sympatric sages, lever length and the area of pollen placement are of particular interest. A shared pollinator bears species-specific areas of pollen placement for different sages. The accurate pollen placement ensures an efficient pollination. However, the question of the functionality of the lever mechanism can not be answered with absolute certainty. The lever‘s backswing is not caused by the adaxial lever arm; the adaxial lever arm is too light and too short to be an adequate counterweight to the abaxial lever arm. Therefore, the adaxial lever arm can not pull the abaxial lever arm to return it to its neutral position. But there are indications of a cellular mainspring in the filament. According to the current state of knowledge, this is the most plausible explanation for the lever's backswing, but further histological investigations on the joint of the lever mechanism are necessary to confirm this assumption.

Soil biogenic emissions of nitric oxide from arid and semi-arid ecosystems

The biogenic production of NO in the soil accounts for between 10% and 40% of the global total. A large degree of the uncertainty in the estimation of the biogenic emissions stems from a shortage of measurements in arid regions, which comprise 40% of the earth’s land surface area. This study examined the emission of NO from three ecosystems in southern Africa which cover an aridity gradient from semi-arid savannas in South Africa to the hyper-arid Namib Desert in Namibia. A laboratory method was used to determine the release of NO as a function of the soil moisture and the soil temperature. Various methods were used to up-scale the net potential NO emissions determined in the laboratory to the vegetation patch, landscape or regional level. The importance of landscape, vegetation and climatic characteristics is emphasized. The first study occurred in a semi-arid savanna region in South Africa, where soils were sampled from 4 landscape positions in the Kruger National Park. The maximum NO emission occurred at soil moisture contents of 10%-20% water filled pore space (WFPS). The highest net potential NO emissions came from the low lying landscape positions, which have the largest nitrogen (N) stocks and the largest input of N. Net potential NO fluxes obtained in the laboratory were converted in field fluxes for the period 2003-2005, for the four landscape positions, using soil moisture and temperature data obtained in situ at the Kruger National Park Flux Tower Site. The NO emissions ranged from 1.5-8.5 kg ha-1 a-1. The field fluxes were up-scaled to a regional basis using geographic information system (GIS) based techniques, this indicated that the highest NO emissions occurred from the Midslope positions due to their large geographical extent in the research area. Total emissions ranged from 20x103 kg in 2004 to 34x103 kg in 2003 for the 56000 ha Skukuza land type. The second study occurred in an arid savanna ecosystem in the Kalahari, Botswana. In this study I collected soils from four differing vegetation patch types including: Pan, Annual Grassland, Perennial Grassland and Bush Encroached patches. The maximum net potential NO fluxes ranged from 0.27 ng m-2 s-1 in the Pan patches to 2.95 ng m-2 s-1 in the Perennial Grassland patches. The net potential NO emissions were up-scaled for the year December 2005-November 2006. This was done using 1) the net potential NO emissions determined in the laboratory, 2) the vegetation patch distribution obtained from LANDSAT NDVI measurements 3) estimated soil moisture contents obtained from ENVISAT ASAR measurements and 4) soil surface temperature measurements using MODIS 8 day land surface temperature measurements. This up-scaling procedure gave NO fluxes which ranged from 1.8 g ha-1 month-1 in the winter months (June and July) to 323 g ha-1 month-1 in the summer months (January-March). Differences occurred between the vegetation patches where the highest NO fluxes occurred in the Perennial Grassland patches and the lowest in the Pan patches. Over the course of the year the mean up-scaled NO emission for the studied region was 0.54 kg ha-1 a-1 and accounts for a loss of approximately 7.4% of the estimated N input to the region. The third study occurred in the hyper-arid Namib Desert in Namibia. Soils were sampled from three ecosystems; Dunes, Gravel Plains and the Riparian zone of the Kuiseb River. The net potential NO flux measured in the laboratory was used to estimate the NO flux for the Namib Desert for 2006 using modelled soil moisture and temperature data from the European Centre for Medium Range Weather Forecasts (ECMWF) operational model on a 36km x 35km spatial resolution. The maximum net potential NO production occurred at low soil moisture contents (<10%WFPS) and the optimal temperature was 25°C in the Dune and Riparian ecosystems and 35°C in the Gravel Plain Ecosystems. The maximum net potential NO fluxes ranged from 3.0 ng m-2 s-1 in the Riparian ecosystem to 6.2 ng m-2 s-1 in the Gravel Plains ecosystem. Up-scaling the net potential NO flux gave NO fluxes of up to 0.062 kg ha-1 a-1 in the Dune ecosystem and 0.544 kg h-1 a-1 in the Gravel Plain ecosystem. From these studies it is shown that NO is emitted ubiquitously from terrestrial ecosystems, as such the NO emission potential from deserts and scrublands should be taken into account in the global NO models. The emission of NO is influenced by various factors such as landscape, vegetation and climate. This study looks at the potential emissions from certain arid and semi-arid environments in southern Africa and other parts of the world and discusses some of the important factors controlling the emission of NO from the soil.

The impact of ice crystals on radiative forcing and remote sensing of arctic boundary-layer mixed-phase clouds

This PhD thesis is embedded into the Arctic Study of Tropospheric Aerosol, Clouds and Radiation (ASTAR) and investigates the radiative transfer through Arctic boundary-layer mixed-phase (ABM) clouds. For this purpose airborne spectral solar radiation measurements and simulations of the solar and thermal infrared radiative transfer have been performed. This work reports on measurements with the Spectral Modular Airborne Radiation measurement sysTem (SMART-Albedometer) conducted in the framework of ASTAR in April 2007 close to Svalbard. For ASTAR the SMART-Albedometer was extended to measure spectral radiance. The development and calibration of the radiance measurements are described in this work. In combination with in situ measurements of cloud particle properties provided by the Laboratoire de M¶et¶eorologie Physique (LaMP) and simultaneous airborne lidar measurements by the Alfred Wegener Institute for Polar and Marine Research (AWI) ABM clouds were sampled. The SMART-Albedometer measurements were used to retrieve the cloud thermodynamic phase by three different approaches. A comparison of these results with the in situ and lidar measurements is presented in two case studies. Beside the dominating mixed-phase clouds pure ice clouds were found in cloud gaps and at the edge of a large cloud field. Furthermore the vertical distribution of ice crystals within ABM clouds was investigated. It was found that ice crystals at cloud top are necessary to describe the observed SMART-Albedometer measurements. The impact of ice crystals on the radiative forcing of ABM clouds is in vestigated by extensive radiative transfer simulations. The solar and net radiative forcing was found to depend on the ice crystal size, shape and the mixing ratio of ice crystals and liquid water droplets.

Exploring physical processes related to past climate proxies: lake sediments and stable water isotopes

Proxy data are essential for the investigation of climate variability on time scales larger than the historical meteorological observation period. The potential value of a proxy depends on our ability to understand and quantify the physical processes that relate the corresponding climate parameter and the signal in the proxy archive. These processes can be explored under present-day conditions. In this thesis, both statistical and physical models are applied for their analysis, focusing on two specific types of proxies, lake sediment data and stable water isotopes.rnIn the first part of this work, the basis is established for statistically calibrating new proxies from lake sediments in western Germany. A comprehensive meteorological and hydrological data set is compiled and statistically analyzed. In this way, meteorological times series are identified that can be applied for the calibration of various climate proxies. A particular focus is laid on the investigation of extreme weather events, which have rarely been the objective of paleoclimate reconstructions so far. Subsequently, a concrete example of a proxy calibration is presented. Maxima in the quartz grain concentration from a lake sediment core are compared to recent windstorms. The latter are identified from the meteorological data with the help of a newly developed windstorm index, combining local measurements and reanalysis data. The statistical significance of the correlation between extreme windstorms and signals in the sediment is verified with the help of a Monte Carlo method. This correlation is fundamental for employing lake sediment data as a new proxy to reconstruct windstorm records of the geological past.rnThe second part of this thesis deals with the analysis and simulation of stable water isotopes in atmospheric vapor on daily time scales. In this way, a better understanding of the physical processes determining these isotope ratios can be obtained, which is an important prerequisite for the interpretation of isotope data from ice cores and the reconstruction of past temperature. In particular, the focus here is on the deuterium excess and its relation to the environmental conditions during evaporation of water from the ocean. As a basis for the diagnostic analysis and for evaluating the simulations, isotope measurements from Rehovot (Israel) are used, provided by the Weizmann Institute of Science. First, a Lagrangian moisture source diagnostic is employed in order to establish quantitative linkages between the measurements and the evaporation conditions of the vapor (and thus to calibrate the isotope signal). A strong negative correlation between relative humidity in the source regions and measured deuterium excess is found. On the contrary, sea surface temperature in the evaporation regions does not correlate well with deuterium excess. Although requiring confirmation by isotope data from different regions and longer time scales, this weak correlation might be of major importance for the reconstruction of moisture source temperatures from ice core data. Second, the Lagrangian source diagnostic is combined with a Craig-Gordon fractionation parameterization for the identified evaporation events in order to simulate the isotope ratios at Rehovot. In this way, the Craig-Gordon model can be directly evaluated with atmospheric isotope data, and better constraints for uncertain model parameters can be obtained. A comparison of the simulated deuterium excess with the measurements reveals that a much better agreement can be achieved using a wind speed independent formulation of the non-equilibrium fractionation factor instead of the classical parameterization introduced by Merlivat and Jouzel, which is widely applied in isotope GCMs. Finally, the first steps of the implementation of water isotope physics in the limited-area COSMO model are described, and an approach is outlined that allows to compare simulated isotope ratios to measurements in an event-based manner by using a water tagging technique. The good agreement between model results from several case studies and measurements at Rehovot demonstrates the applicability of the approach. Because the model can be run with high, potentially cloud-resolving spatial resolution, and because it contains sophisticated parameterizations of many atmospheric processes, a complete implementation of isotope physics will allow detailed, process-oriented studies of the complex variability of stable isotopes in atmospheric waters in future research.rn

New biosensor applications of surface plasmon and hydrogel optical waveguide spectroscopy

Rapid and sensitive detection of chemical and biological analytes becomes increasingly important in areas such as medical diagnostics, food control and environmental monitoring. Optical biosensors based on surface plasmon resonance (SPR) and optical waveguide spectroscopy have been extensively pushed forward in these fields. In this study, we combine SPR, surface plasmon-enhanced fluorescence spectroscopy (SPFS) and optical waveguide spectroscopy with hydrogel thin film for highly sensitive detection of molecular analytes.rnrnA novel biosensor based on SPFS which was advanced through the excitation of long range surface plasmons (LRSPs) is reported in this study. LRSPs are special surface plasmon waves propagating along thin metal films with orders of magnitude higher electromagnetic field intensity and lower damping than conventional SPs. Therefore, their excitation on the sensor surface provides further increased fluorescence signal. An inhibition immunoassay based on LRSP-enhanced fluorescence spectroscopy (LRSP-FS) was developed for the detection of aflatoxin M1 (AFM1) in milk. The biosensor allowed for the detection of AFM1 in milk at concentrations as low as 0.6 pg mL-1, which is about two orders of magnitude lower than the maximum AFM1 residue level in milk stipulated by the European Commission legislation.rnrnIn addition, LRSPs probe the medium adjacent to the metallic surface with more extended evanescent field than regular SPs. Therefore, three-dimensional binding matrices with up to micrometer thickness have been proposed for the immobilization of biomolecular recognition elements with large surface density that allows to exploit the whole evanescent field of LRSP. A photocrosslinkable carboxymethyl dextran (PCDM) hydrogel thin film is used as a binding matrix, and it is applied for the detection of free prostate specific antigen (f-PSA) based on the LRSP-FS and sandwich immunoassay. We show that this approach allows for the detection of f-PSA at low femto-molar range, which is approximately four orders of magnitude lower than that for direct detection of f-PSA based on the monitoring of binding-induced refractive index changes.rnrnHowever, a three dimensional hydrogel binding matrix with micrometer thickness can also serve as an optical waveguide. Based on the measurement of binding-induced refractive index changes, a hydrogel optical waveguide spectroscopy (HOWS) is reported for a label-free biosensor. This biosensor is implemented by using a SPR optical setup in which a carboxylated poly(N-isoproprylacrylamide) (PNIPAAm) hydrogel film is attached on a metallic surface and modified by protein catcher molecules. Compared to regular SPR biosensor with thiol self-assembled monolayer (SAM), HOWS provides an order of magnitude improved resolution in the refractive index measurements and enlarged binding capacity owing to its low damping and large swelling ratio, respectively. A model immunoassay experiment revealed that HOWS allowed detection of IgG molecules with a 10 pM limit of detection (LOD) that was five-fold lower than that achieved for SPR with thiol SAM. For the high capacity hydrogel matrix, the affinity binding was mass transport limited.rnrnThe mass transport of target molecules to the sensor surface can play as critical a role as the chemical reaction itself. In order to overcome the diffusion-limited mass transfer, magnetic iron oxide nanoparticles were employed. The magnetic nanoparticles (MNPs) can serve both as labels providing enhancement of the refractive index changes, and “vehicles” for rapidly delivering the analytes from sample solution to an SPR sensor surface with a gradient magnetic field. A model sandwich assay for the detection of β human chorionic gonadotropin (βhCG) has been utilized on a gold sensor surface with metallic diffraction grating structure supporting the excitation of SPs. Various detection formats including a) direct detection, b) sandwich assay, c) MNPs immunoassay without and d) with applied magnetic field were compared. The results show that the highly-sensitive MNPs immunoassay improves the LOD on the detection of βhCG by a factor of 5 orders of magnitude with respect to the direct detection.rn

Experimental Analysis and Numerical Simulation of Quench in Superconducting HTS Tapes and Coils

The quench characteristics of second generation (2 G) YBCO Coated Conductor (CC) tapes are of fundamental importance for the design and safe operation of superconducting cables and magnets based on this material. Their ability to transport high current densities at high temperature, up to 77 K, and at very high fields, over 20 T, together with the increasing knowledge in their manufacturing, which is reducing their cost, are pushing the use of this innovative material in numerous system applications, from high field magnets for research to motors and generators as well as for cables. The aim of this Ph. D. thesis is the experimental analysis and numerical simulations of quench in superconducting HTS tapes and coils. A measurements facility for the characterization of superconducting tapes and coils was designed, assembled and tested. The facility consist of a cryostat, a cryocooler, a vacuum system, resistive and superconducting current leads and signal feedthrough. Moreover, the data acquisition system and the software for critical current and quench measurements were developed. A 2D model was developed using the finite element code COMSOL Multiphysics R . The problem of modeling the high aspect ratio of the tape is tackled by multiplying the tape thickness by a constant factor, compensating the heat and electrical balance equations by introducing a material anisotropy. The model was then validated both with the results of a 1D quench model based on a non-linear electric circuit coupled to a thermal model of the tape, to literature measurements and to critical current and quench measurements made in the cryogenic facility. Finally the model was extended to the study of coils and windings with the definition of the tape and stack homogenized properties. The procedure allows the definition of a multi-scale hierarchical model, able to simulate the windings with different degrees of detail.

Dielectrophoresis (dep) and electrowetting (ewod) as an anti-fouling process for antibacterial surfaces

Nowadays the medical field is struggling to decrease bacteria biofilm formation which leads to infection. Biomedical devices sterilization has not changed over a long period of time. This results in high costs for hospitals healthcare managements. The objective of this project is to investigate electric field effects and surface energy manipulation as solutions for preventing bacteria biofilm for future devices. Based on electrokinectic environments 2 different methods were tested: feasibility of electric gradient through mediums (DEP) reinforced by numerical simulations; and EWOD by the fabrication of golden interdigitated electrodes on silicon glass substrates, standard ~480 nm Teflon (PTFE) layer and polymeric gasket to contain the bacteria medium. In the first experiment quantitative analysis was carried out to achieve forces required to reject bacteria without considering dielectric environment limitations as bacteria and medium frequency dependence. In the second experiment applied voltages was characterized by droplets contact angle measurements and put to the live bacteria tests. The project resulted on promising results for DEP application due to its wide range of frequency that can be used to make a “general” bacteria rejecting; but in terms of practicality, EWOD probably have higher potential for success but more experiments are needed to verify if can prevent biofilm adhesion besides the Teflon non-adhesive properties (including limitations as Teflon breakthrough, layer sensitivity) at incubation times larger than 24 hours.

Aircraft-based in-situ aerosol mass spectrometry: Chemical characterization and source identification of submicron particulate matter in the free and upper troposphere and lower stratosphere

The composition of the atmosphere is frequently perturbed by the emission of gaseous and particulate matter from natural as well as anthropogenic sources. While the impact of trace gases on the radiative forcing of the climate is relatively well understood the role of aerosol is far more uncertain. Therefore, the study of the vertical distribution of particulate matter in the atmosphere and its chemical composition contribute valuable information to bridge this gap of knowledge. The chemical composition of aerosol reveals information on properties such as radiative behavior and hygroscopicity and therefore cloud condensation or ice nucleus potential. rnThis thesis focuses on aerosol pollution plumes observed in 2008 during the POLARCAT (Polar Study using Aircraft, Remote Sensing, Surface Measurements and Models, of Climate, Chemistry, Aerosols, and Transport) campaign over Greenland in June/July and CONCERT (Contrail and Cirrus Experiment) campaign over Central and Western Europe in October/November. Measurements were performed with an Aerodyne compact time-of-flight aerosol mass spectrometer (AMS) capable of online size-resolved chemical characterization of non-refractory submicron particles. In addition, the origins of pollution plumes were determined by means of modeling tools. The characterized pollution episodes originated from a large variety of sources and were encountered at distinct altitudes. They included pure natural emissions from two volcanic eruptions in 2008. By the time of detection over Western Europe between 10 and 12 km altitude the plume was about 3 months old and composed to 71 % of particulate sulfate and 21 % of carbonaceous compounds. Also, biomass burning (BB) plumes were observed over Greenland between 4 and 7 km altitude (free troposphere) originating from Canada and East Siberia. The long-range transport took roughly one and two weeks, respectively. The aerosol was composed of 78 % organic matter and 22 % particulate sulfate. Some Canadian and all Siberian BB plumes were mixed with anthropogenic emissions from fossil fuel combustion (FF) in North America and East Asia. It was found that the contribution of particulate sulfate increased with growing influences from anthropogenic activity and Asia reaching up to 37 % after more than two weeks of transport time. The most exclusively anthropogenic emission source probed in the upper troposphere was engine exhaust from commercial aircraft liners over Germany. However, in-situ characterization of this aerosol type during aircraft chasing was not possible. All long-range transport aerosol was found to have an O:C ratio close to or greater than 1 implying that low-volatility oxygenated organic aerosol was present in each case despite the variety of origins and the large range in age from 3 to 100 days. This leads to the conclusion that organic particulate matter reaches a final and uniform state of oxygenation after at least 3 days in the free troposphere. rnExcept for aircraft exhaust all emission sources mentioned above are surface-bound and thus rely on different types of vertical transport mechanisms, such as direct high altitude injection in the case of a volcanic eruption, or severe BB, or uplift by convection, to reach higher altitudes where particles can travel long distances before removal mainly caused by cloud scavenging. A lifetime for North American mixed BB and FF aerosol of 7 to 11 days was derived. This in consequence means that emission from surface point sources, e.g. volcanoes, or regions, e.g. East Asia, do not only have a relevant impact on the immediate surroundings but rather on a hemispheric scale including such climate sensitive zones as the tropopause or the Arctic.

Uptake mechanism, intracellular trafficking and endo-lysosomal pH monitoring of polystyrene nanoparticles

What is the intracellular fate of nanoparticles (NPs) taken up by the cells? This question has been investigated for polystyrene NPs of different sizes with a set of molecular biological and biophysical techniques.rnTwo sets of fluorescent NPs, cationic and non-ionic, were synthesized with three different polymerization techniques. Non-ionic particles (132 – 846 nm) were synthesized with dispersion polymerization in an ethanol/water solution. Cationic NPs with 120 nm were synthesized by miniemulsion polymerization Particles with 208, 267 and 603 nm were produced by seeding the 120 nm particle obtained by miniemulsion polymerization with drop-wise added monomer and polymerization of such. The colloidal characterization of all particles showed a comparable amount of the surface groups. In addition, particles were characterized with regard to their size, morphology, solid content, amount of incorporated fluorescent dye and zeta potential. The fluorescent intensities of all particles were measured by fluorescence spectroscopy for calibration in further cellular experiments. rnThe uptake of the NPs to HeLa cells after 1 – 24 h revealed a much higher uptake of cationic NPs in comparison to non-ionic NPs. If the same amount of NPs with different sizes is introduced to the cell, a different amount of particles is present in the cell medium, which complicates a comparison of the uptake. The same conclusion is valid for the particles’ overall surface area. Therefore, HeLa cells were incubated with the same concentration, amount and surface area of NPs. It was found that with the same concentration always the same polymer amount is taking up by cells. However, the amount of particles taken up decreases for the biggest. A correlation to the surface area could not be found. We conclude that particles are endocytosed by an excavator-shovel like mechanism, which does not distinguish between different sizes, but is only dependent on the volume that is taken up. For the decreased amount of large particles, an overload of this mechanism was assumed, which leads to a decrease in the uptake. rnThe participation of specific endocytotic processes has been determined by the use of pharmacological inhibitors, immunocytological staining and immunofluorescence. The uptake of NPs into the endo-lysosomal machinery is dominated by a caveolin-mediated endocytosis. Other pathways, which include macropinocytosis and a dynamin-dependent mechanism but exclude clathrin mediated endocytosis, also occur as competing processes. All particles can be found to some extent in early endosomes, but only bigger particles were proven to localize in late endosomes. No particles were found in lysosomes; at least not in lysosomes that are labeled with Lamp1 and cathepsin D. However, based on the character of the performed experiment, a localization of particles in lysosomes cannot be excluded.rnDuring their ripening process, vesicles undergo a gradual acidification from early over late endosomes to lysosomes. It is hypothesized that NPs in endo-lysosomal compartments experience the same change in pH value. To probe the environmental pH of NPs after endocytosis, the pH-sensitive dye SNARF-4F was grafted onto amino functionalized polystyrene NPs. The pH value is a ratio function of the two emission wavelengths of the protonated and deprotonated form of the dye and is hence independent of concentration changes. The particles were synthesized by the aforementioned miniemulsion polymerization with the addition of the amino functionalized copolymer AEMH. The immobilization of SNARF-4F was performed by an EDC-coupling reaction. The amount of physically adsorbed dye in comparison to covalently bonded dye was 15% as determined by precipitation of the NPs in methanol, which is a very good solvent for SNARF-4F. To determine influences of cellular proteins on the fluorescence properties, a intracellular calibration fit was established with platereader measurements and cLSM imaging by the cell-penetrable SNARF-4F AM ester. Ionophores equilibrated the extracellular and intracellular pH.rnSNARF-4F NPs were taken up well by HeLa cells and showed no toxic effects. The pH environment of SNARF-4F NPs has been qualitatively imaged as a movie over a time period up to 1 h in pseudo-colors by a self-written automated batch program. Quantification revealed an acidification process until pH value of 4.5 over 24 h, which is much slower than the transport of nutrients to lysosomes. NPs are present in early endosomes after min. 1 h, in late endosomes at approx. 8 h and end up in vesicles with a pH value typical for lysosomes after > 24 h. We therefore assume that NPs bear a unique endocytotic mechanism, at least with regards to the kinetic involvedrn

Electronic structure and physical properties of Heusler compounds for thermoelectric and spintronic applications

This thesis focuses on synthesis as well as investigations of the electronic structure and properties of Heusler compounds for spintronic and thermoelectric applications.rnThe first part reports on the electronic and crystal structure as well as the mechanical, magnetic, and transport properties of the polycrystalline Heusler compound Co2MnGe. The crystalline structure was examined in detail by extended X-ray absorption fine structure spectroscopy and anomalous X-ray diffraction. The low-temperature magnetic moment agrees well with the Slater-Pauling rule and indicates a half-metallic ferromagnetic state of the compound, as is predicted by ab-initio calculations. Transport measurements and hard X-ray photoelectron spectroscopy (HAXPES) were performed to explain the electronic structure of the compound.rnA major part of the thesis deals with a systematical investigation of Heusler compounds for thermoelectric applications. Few studies have been reported on thermoelectric properties of p-type Heusler compounds. Therefore, this thesis focuses on the search for new p-type Heusler compounds with high thermoelectric efficiency. The substitutional series NiTi1−xMxSn and CoTi1−xMxSb (where M = Sc, V and 0 ≤ x ≤ 0.2) were synthesized and investigated theoretically and experimentally with respect to electronic structure and transport properties. The results show the possibility to create n-type and p-type thermoelectrics within one Heusler compound. The pure compounds showed n-type behavior, while under Sc substitution the system switched to p-type behavior. A maximum Seebeck coefficient of +230 μV/K (at 350 K) was obtained for NiTi0.26Sc0.04Zr0.35Hf0.35Sn, which is one of the highest values for p-type thermoelectric compounds based on Heusler alloys up to now. HAXPES valence band measurement show massive in gap states for the parent compounds NiTiSn, CoTiSb and NiTi0.3Zr0.35Hf0.35Sn. This proves that the electronic states close to the Fermi energy play a key role for the behavior of the transport properties. Furthermore, the electronic structure of the gapless Heusler compounds PtYSb, PtLaBi and PtLuSb were investigated by bulk sensitive HAXPES. The linear behavior of the spectra close to εF proves the bulk origin of Dirac-cone type density of states. Furthermore, a systematic study on the optical and transport properties of PtYSb is presented. The compound exhibits promising thermoelectric properties with a high figure of merit (ZT = 0.2) and a Hall mobility μh of 300 cm2/Vs at 350 K.rnThe last part of this thesis describes the linear dichroism in angular-resolved photoemission from the valence band of NiTi0.9Sc0.1Sn and NiMnSb. High resolution photoelectron spectroscopy was performed with an excitation energy of hν = 7.938 keV. The linear polarization of the photons was changed using an in-vacuum diamond phase retarder. Noticeable linear dichroism is found in the valence bands and this allows for a symmetry analysis of the contributing states. The differences in the spectra are found to be caused by symmetry dependent angular asymmetry parameters, and these occur even in polycrystalline samples without preferential crystallographic orientation.rnIn summary, Heusler compounds with 1:1:1 and 2:1:1 stoichiometry were synthesized and examined by chemical and physical methods. Overall, this thesis shows that the combination of first-principle calculations, transport measurements and high resolution high energy photoelectron spectroscopy analysis is a very powerful tool for the design and development of new materials for a wide range of applications from spintronic applications to thermoelectric applications.rn

Nucleon electromagnetic structure studies in the spacelike and timelike regions

The thesis investigates the nucleon structure probed by the electromagnetic interaction. One of the most basic observables, reflecting the electromagnetic structure of the nucleon, are the form factors, which have been studied by means of elastic electron-proton scattering with ever increasing precision for several decades. In the timelike region, corresponding with the proton-antiproton annihilation into a electron-positron pair, the present experimental information is much less accurate. However, in the near future high-precision form factor measurements are planned. About 50 years after the first pioneering measurements of the electromagnetic form factors, polarization experiments stirred up the field since the results were found to be in striking contradiction to the findings of previous form factor investigations from unpolarized measurements. Triggered by the conflicting results, a whole new field studying the influence of two-photon exchange corrections to elastic electron-proton scattering emerged, which appeared as the most likely explanation of the discrepancy. The main part of this thesis deals with theoretical studies of two-photon exchange, which is investigated particularly with regard to form factor measurements in the spacelike as well as in the timelike region. An extraction of the two-photon amplitudes in the spacelike region through a combined analysis using the results of unpolarized cross section measurements and polarization experiments is presented. Furthermore, predictions of the two-photon exchange effects on the e+p/e-p cross section ratio are given for several new experiments, which are currently ongoing. The two-photon exchange corrections are also investigated in the timelike region in the process pbar{p} -> e+ e- by means of two factorization approaches. These corrections are found to be smaller than those obtained for the spacelike scattering process. The influence of the two-photon exchange corrections on cross section measurements as well as asymmetries, which allow a direct access of the two-photon exchange contribution, is discussed. Furthermore, one of the factorization approaches is applied for investigating the two-boson exchange effects in parity-violating electron-proton scattering. In the last part of the underlying work, the process pbar{p} -> pi0 e+e- is analyzed with the aim of determining the form factors in the so-called unphysical, timelike region below the two-nucleon production threshold. For this purpose, a phenomenological model is used, which provides a good description of the available data of the real photoproduction process pbar{p} -> pi0 gamma.

Stress abiotici e trattamenti ultra-diluiti: effetti fisiologici e molecolari sulla crescita in vitro di frumento

Gli stress abiotici determinando modificazioni a livello fisiologico, biochimico e molecolare delle piante, costituiscono una delle principali limitazioni per la produzione agricola mondiale. Nel 2007 la FAO ha stimato come solamente il 3,5% della superficie mondiale non sia sottoposta a stress abiotici. Il modello agro-industriale degli ultimi cinquant'anni, oltre ad avere contribuito allo sviluppo economico dell'Europa, è stato anche causa di inquinamento di acqua, aria e suolo, mediante uno sfruttamento indiscriminato delle risorse naturali. L'arsenico in particolare, naturalmente presente nell'ambiente e rilasciato dalle attività antropiche, desta particolare preoccupazione a causa dell'ampia distribuzione come contaminante ambientale e per gli effetti di fitotossicità provocati. In tale contesto, la diffusione di sistemi agricoli a basso impatto rappresenta una importante risorsa per rispondere all'emergenza del cambiamento climatico che negli anni a venire sottoporrà una superficie agricola sempre maggiore a stress di natura abiotica. Nello studio condotto è stato utilizzato uno stabile modello di crescita in vitro per valutare l'efficacia di preparati ultra diluiti (PUD), che non contenendo molecole chimiche di sintesi ben si adattano a sistemi agricoli sostenibili, su semi di frumento preventivamente sottoposti a stress sub-letale da arsenico. Sono state quindi condotte valutazioni sia a livello morfometrico (germinazione, lunghezza di germogli e radici) che molecolare (espressione genica valutata mediante analisi microarray, con validazione tramite Real-Time PCR) arricchendo la letteratura esistente di interessanti risultati. In particolare è stato osservato come lo stress da arsenico, determini una minore vigoria di coleptile e radici e a livello molecolare induca l'attivazione di pathways metabolici per proteggere e difendere le cellule vegetali dai danni derivanti dallo stress; mentre il PUD in esame (As 45x), nel sistema stressato ha indotto un recupero nella vigoria di germoglio e radici e livelli di espressione genica simili a quelli riscontrati nel controllo suggerendo un effetto "riequilibrante" del metabolismo vegetale.

Das GAF-Domänen-Protein NreA : ein neuartiger Nitratrezeptor aus Staphylococcus carnosus

Staphylococcus carnosus ist ein fakultativ anaerobes Bakterium, das aerobe Atmung, anaerobe Nitratatmung und Gärungsstoffwechsel betreiben kann. Die Expression des Nitratstoffwechsels wird durch das Dreikomponentensystem NreABC reguliert.rnUnter anaeroben Bedingungen besitzt die Sensorhistidinkinase NreB in ihrer PAS-Domäne ein [Fe4S4]2+-Cluster. Das aktive (anaerobe) [Fe4S4]2+-NreB überträgt nach Autophosphorylierung die Phosphorylgruppe auf den Antwortregulator NreC, welcher dann die Expression der Gene der Nitratatmung aktiviert. Nitrat wirkt mit Hilfe des NreA-Proteins auf diese Gene induzierend. Im Rahmen der vorliegenden Arbeit wurde gezeigt, dass NreA ein GAF-Domänen-Protein und ein neuartiger Nitratrezeptor ist.rnDie Natur von NreA als GAF-Domänen-Protein bestätigte sich beim Vergleich der Kristallstruktur mit denen anderer GAF-Domänen. GAF-Domänen sind weit verbreitet und binden typischer Weise kleine Moleküle. Als physiologischer Ligand von NreA zeigte sich Nitrat, das innerhalb einer definierten Bindetasche gebunden wird. NreA bindet vermutlich in dimerer Form an dimeres NreB und inhibiert dadurch die Phosphorylierung der Sensorhistidinkinase NreB. Die Interaktion von NreA mit NreB wurde in vivo durch BACTH-Messungen und sowohl in vivo als auch in vitro durch Cross-Linking Experimente gezeigt. Nitrat reduziert den Ergebnissen nach die Interaktion von NreA mit NreB.rnDurch Sequenzvergleiche von NreA mit Homologen wurden konservierte Aminosäuren identifiziert. Über gerichtete Mutagenese wurden 25 NreA-Varianten hergestellt und bezüglich ihres Verhaltens in Abhängigkeit von Nitrat in narG-lip-Reportergenstudien getestet. Anhand ihres Phänotyps wurden sie als Wildtyp, NreA- und NreABC-Mutanten klassifiziert. Die Nitratbindetasche war in sechs Fällen betroffen. Die Phänotypen der Mutationen in der Peripherie lassen sich mit Auswirkungen auf die vermutete Konformationsänderung oder auf die Interaktion mit NreB erklären. Mutationen von konservierten, oberflächenexponierten Resten führten vermehrt zu NreA/ON-Varianten. Es ließen sich Bereiche auf der Proteinoberfläche identifizieren, die für NreA/NreA- oder NreA/NreB-Interaktionen wichtig sein könnten.rnDie Untersuchungen zeigten, dass NreA mit NreB interagiert und dass dadurch ein NreA/NreB-Sensorkomplex für die gemeinsame Erkennung von Nitrat und Sauerstoff gebildet wird.