Electrochemical properties and intermediate-temperature fuel cell performance of dense yttrium-doped barium zirconate with calcium addition

Although BaZr 0.8Y 0.2O 3-δ(BZY) possesses large bulk proton conductivity and excellent chemical stability, its poor sinterability and grain boundaries block proton conduction. In this work, the effect of Ca as a co-dopant and as a sintering aid (as CaO), on the sinterability, proton conductivity, and fuel cell performance of BZY was investigated. The addition of 4 mol% CaO significantly improved the BZY sinterability: BZY pellets with densities of 92.7% and 97.5% with respect to the theoretical density were obtained after sintering at 1500°C and 1600°C, respectively. The improved BZY sinterability by CaO addition resulted also in a large proton conductivity; at 600°C, the total conductivity of BZY-CaO was 2.14 × 10 -3 S/cm, in wet Ar. Anode-supported fuel cells with 25 μm-thick BZY-CaO electrolyte membranes were fabricated by a dual-layer co-firing technique. The peak power density of the fuel cell with a BZY-Ni/BZY-4CaO/BZY-LSCF (La 0.6Sr 0.4Fe 0.8Co 0.2O 3-δ) configuration was 141 mW/cm 2 at 700°C, several times larger than the reported values of BZY electrolyte membrane fuel cells sintered with the addition of CuO or ZnO, demonstrating promising features for practical fuel cell applications.

A numerical study of crack tip constraint in ductile single crystals

In this work, the effect of crack tip constraint on near-tip stress and deformation fields in a ductile FCC single crystal is studied under mode I, plane strain conditions. To this end, modified boundary layer simulations within crystal plasticity framework are performed, neglecting elastic anisotropy. The first and second terms of the isotropic elastic crack tip field, which are governed by the stress intensity factor K and T-stress, are prescribed as remote boundary conditions and solutions pertaining to different levels of T-stress are generated. It is found that the near-tip deformation field, especially, the development of kink or slip shear bands, is sensitive to the constraint level. The stress distribution and the size and shape of the plastic zone near the crack tip are also strongly influenced by the level of T-stress, with progressive loss of crack tip constraint occurring as T-stress becomes more negative. A family of near-tip fields is obtained which are characterized by two terms (such as K and T or J and a constraint parameter Q) as in isotropic plastic solids.

Understanding curriculum planning practices that promote equity and excellence for students with disability

This thesis analyses how primary teachers plan from the Australian Curriculum for students with disabilities as part of their curriculum planning to achieve equity and excellence for all. The researcher used an institutional ethnographic approach to create data maps that visually represented how these teachers navigated across thirty-one curriculum organising texts in their individual and classroom planning. By identifying the complexity of the process, types of texts that were most influential, and the everyday/night work of curriculum planning, leaders can strategically plan to support teachers to have high expectations for students with disabilities. Key themes include students with disability, curriculum entitlement and practices that promote equity.

A finite element analysis of quasistatic crack growth in a pressure sensitive constrained ductile layer

Polymeric adhesive layers are employed for bonding two components in a wide variety of technological applications, It has been observed that, unlike in metals, the yield behavior of polymers is affected by the state of hydrostatic stress. In this work, the effect of pressure sensitivity of yielding and layer thickness on quasistatic interfacial crack growth in a ductile adhesive layer is investigated. To this end, finite deformation, finite element analyses of a cracked sandwiched layer are carried out under plane strain, small-scale yielding conditions for a wide range of mode mixities. The Drucker-Prager constitutive equations are employed to represent the behavior of the layer. Crack propagation is simulated through a cohesive zone model, in which the interface is assumed to follow a prescribed traction-separation law. The results show that for a given mode mixity, the steady state Fracture toughness [K](ss) is enhanced as the degree of pressure sensitivity increases. Further, for a given level of pressure sensitivity, [K](ss) increases steeply as mode Il loading is approached. (C) 2000 Elsevier Science Ltd. All rights reserved.

Critical buckling temperature of single-walled carbon nanotubes embedded in a one-parameter elastic medium based on nonlocal continuum mechanics

In this paper, the critical budding temperature of single-walled carbon nanotubes (SWCNTs), which are embedded in one-parameter elastic medium (Winkler foundation) is estimated under the umbrella of continuum mechanics theory. Nonlocal continuum theory is incorporated into Timoshenko beam model and the governing differential equations of motion are derived. An explicit expression for the non-dimensional critical buckling temperature is also derived in this work. The effect of the nonlocal small scale coefficient, the Winkler foundation parameter and the ratio of the length to the diameter on the critical buckling temperature is investigated in detail. It can be observed that the effects of nonlocal small scale parameter and the Winkler foundation parameter are significant and should be considered for thermal analysis of SWCNTs. The results presented in this paper can provide useful guidance for the study and design of the next generation of nanodevices that make use of the thermal buckling properties of embedded single-walled carbon nanotubes. (C) 2011 Elsevier B.V. All rights reserved.

Wave propagation in single-walled carbon nanotube under longitudinal magnetic field using nonlocal Euler-Bernoulli beam theory

In the present work, the effect of longitudinal magnetic field on wave dispersion characteristics of equivalent continuum structure (ECS) of single-walled carbon nanotubes (SWCNT) embedded in elastic medium is studied. The ECS is modelled as an Euler-Bernoulli beam. The chemical bonds between a SWCNT and the elastic medium are assumed to be formed. The elastic matrix is described by Pasternak foundation model, which accounts for both normal pressure and the transverse shear deformation. The governing equations of motion for the ECS of SWCNT under a longitudinal magnetic field are derived by considering the Lorentz magnetic force obtained from Maxwell's relations within the frame work of nonlocal elasticity theory. The wave propagation analysis is performed using spectral analysis. The results obtained show that the velocity of flexural waves in SWCNTs increases with the increase of longitudinal magnetic field exerted on it in the frequency range: 0-20 THz. The present analysis also shows that the flexural wave dispersion in the ECS of SWCNT obtained by local and nonlocal elasticity theories differ. It is found that the nonlocality reduces the wave velocity irrespective of the presence of the magnetic field and does not influences it in the higher frequency region. Further it is found that the presence of elastic matrix introduces the frequency band gap in flexural wave mode. The band gap in the flexural wave is found to independent of strength of the longitudinal magnetic field. (C) 2011 Elsevier Inc. All rights reserved.

Climate response to changes in atmospheric carbon dioxide and solar irradiance on the time scale of days to weeks

Recent studies show that fast climate response on time scales of less than a month can have important implications for long-term climate change. In this study, we investigate climate response on the time scale of days to weeks to a step-function quadrupling of atmospheric CO2 and contrast this with the response to a 4% increase in solar irradiance. Our simulations show that significant climate effects occur within days of a stepwise increase in both atmospheric CO2 content and solar irradiance. Over ocean, increased atmospheric CO2 warms the lower troposphere more than the surface, increasing atmospheric stability, moistening the boundary layer, and suppressing evaporation and precipitation. In contrast, over ocean, increased solar irradiance warms the lower troposphere to a much lesser extent, causing a much smaller change in evaporation and precipitation. Over land, both increased CO2 and increased solar irradiance cause rapid surface warming that tends to increase both evaporation and precipitation. However, the physiological effect of increased atmospheric CO2 on plant stomata reduces plant transpiration, drying the boundary layer and decreasing precipitation. This effect does not occur with increased solar irradiance. Therefore, differences in climatic effects from CO2 versus solar forcing are manifested within days after the forcing is imposed.

AZ91C magnesium alloy modified by Cd

In the present work, the effect of Cd on the microstructure, mechanical properties and general corrosion behaviour of AZ91C alloys was investigated. Addition of Cd was found not to be efficient in modifying/refining the microstructure or beta-phase. A morphology change in beta-phase from fine continuous precipitates to discontinuous beta-phase upon the addition of Cd was observed. A marginal increment in mechanical properties was observed. General corrosion behaviour was followed with weight loss measurements, potentiostatic polarisation studies and surface studies in 3.5% sodium chloride solution and 3.5% sodium chloride with 2% potassium dichromate solution. Cd addition deteriorated the corrosion behaviour of AZ91C. This behaviour was attributed to the formation of chunks of beta-phase upon the addition of Cd. AZ91C with refined beta-phase distribution, performed rather better in the NaCl solutions. (C) 2013 Elsevier Ltd. All rights reserved.

Influence of mode of deformation on microstructural heterogeneities in Ni subjected to large strain deformation

In the present work, the effect of deformation mode (uniaxial compression, rolling and torsion) on the microstructural heterogeneities in a commercial purity Ni is reported. For a given equivalent von Mises strain, samples subjected to torsion have shown higher fraction of high-angle boundaries, kernel average misorientation and recrystallization nuclei when compared to uniaxially compressed and rolled samples. This is attributed to the differences in the slip system activity under different modes of deformation.

Energy efficiency in trawling operations

Diurnal variation in trawl catches and its influence on energy efficiency of trawler operations are discussed in this paper, based on data on landings of a Japanese factory trawler which operated in the Indian waters during 1992-93. The factory vessel equipped for stern trawling had a length overall of 110 m, GT of 5460 and installed engine power of 5700 hp. Operations were conducted off west coast of India between 31 and 278 m depth contours, using a 80.4 m high opening bottom trawl with an adjusted vertical opening of 7.60.9 m. The catch data was grouped according to the median towing hour, by the time of the day. CPUE obtained was 3713.4 kg.h-1 for day time operations and 1536.6 kg.h-1 for night-time operations. Mean daily catches were 31367 kg.day-1 (SE: 2743) for day time operations and 9430 kg.day-1 (SE: 966) for night-time operations. Fuel consumption were 0.399 and 0.982 kg fuel.kg fish-1, respectively for day and night-time operations. Total catch and catch components such as threadfin bream, bulls eye, hairtails, trevelly, lizard fish showed significant improvement during day-time operations while swarming crabs showed a significant improvement in the night-time operations. The difference in catch rates between day and night could be attributed to diurnal variation in the spatial distribution and schooling behaviour of the catch categories, their differential behaviour in the vicinity of trawl systems under varying light levels of day and night and consequent effect on catching efficiency and size selectivity at different stages in the capture process. The results obtained in addition to its importance in the operational planning of trawling in order to realise objectives of maximising catch per unit effort and minimising fuel consumption per unit volume of fish caught, has added significance in the use of bottom trawl surveys in stock abundance estimates.

Trabalho noturno em unidades fechadas: estudo com trabalhadores de enfermagem num hospital público

Esta pesquisa tem como objetivo geral avaliar as situações que envolvem o trabalho noturno em unidades fechadas, sob a percepção dos profissionais de enfermagem de um hospital público. Trata-se de um estudo descritivo com abordagem quantitativa, utilizando um questionário semiestruturado com perguntas fechadas. O instrumento abrange as condições de trabalho, as condições de saúde, o ambiente de trabalho, as relações com os colegas e com a chefia, a motivação e a percepção do profissional de enfermagem no que se refere à valorização profissional que a sociedade e os outros profissionais atribuem ao seu trabalho. Foi utilizada uma população amostral de noventa sujeitos distribuídos em quatro clínicas fechadas. Os dados foram analisados através do programa Statistical Package for the Social Sciences (SPSS). Os resultados permitiram estabelecer uma relação desses dados com a atuação dos profissionais no que se refere à satisfação na execução dos procedimentos. Os trabalhadores de enfermagem do serviço noturno em unidades fechadas são representados, majoritariamente, por mulheres entre 41 e 50 anos de idade, casadas e com filhos sob sua guarda, 60% apresentam dois vínculos empregatícios com carga horária de trabalho superior a 60 horas semanais, encontram-se satisfeitas por atuarem em unidades fechadas e insatisfeitas com o serviço noturno, apresentando-se, portanto, estressadas e desmotivadas, com ganho de peso e índice elevado de afastamento por motivo de saúde. Os resultados apontam, ainda, que 90% dos participantes nunca receberam incentivos para a realização de cursos de atualização, 63,3% expressaram insatisfação com o dimensionamento de pessoal, o que se traduz em sobrecarga de atividades para os profissionais. Mais de 50% dos participantes da pesquisa sentem-se desvalorizados profissionalmente perante a sociedade e encontram-se insatisfeitos com os salários e benefícios oferecidos pela instituição. No que se refere à exposição a riscos, 86,6% dos profissionais se declararam insatisfeitos e muito insatisfeitos com os riscos ergonômicos. Já os riscos químicos, biológicos, psicossociais e mecânicos apresentaram 50% de índice de insatisfação, seguido pelos riscos físicos com 40%. Os dados desse estudo levam a concluir que existe uma grande complexidade de fatores, cuja interação interfere direta e indiretamente na qualidade do desempenho profissional de enfermagem e contribui para a falta de segurança e insatisfação no trabalho noturno.

Ativação do estresse oxidativo e da resposta antioxidante por ExoU de Pseudomonas aeruginosa

ExoU, uma citotoxina produzida pelo patógeno oportunista Pseudomonas aeruginosa e translocada para o citosol de células hospedeiras via sistema de secreção do tipo III, é associada à gravidade de infecções agudas. No presente trabalho, o efeito de ExoU na ativação do estresse oxidativo e da resposta antioxidante foi avaliado em culturas de células epiteliais respiratórias humanas infectadas com a cepa PA103 de P. aeruginosa (produtora de ExoU), com a mutante deletada no gene exoU, PA103∆exoU, ou com a mutante complementada com exoU sem atividade tipo fosfolipase A2, PA103∆UT/S142A. Análises das dosagens de hidroperóxidos lipídicos e isoprostanos, considerados marcadores de estresse oxidativo, revelaram que ExoU promoveu um aumento em suas concentrações. Foi observado, também, que ExoU estimulou a produção de espécies reativas de oxigênio, óxido nítrico e peroxinitrito nas células infectadas, assim como a expressão de iNOS e eNOS, mas não de nNOS. Além disso, ExoU foi responsável pelo aumento da atividade de SOD1 e pela redução dos níveis de GSH, mas não afetou a atividade da catalase ou de NQO1. No modelo in vivo, a dosagem de malondialdeído, um subproduto da lipoperoxidação de membranas, evidenciou uma maior produção deste composto no pulmão de camundongos infectados pela cepa produtora de ExoU, em comparação ao pulmão de camundongos infectados pela cepa mutante. Em conjunto, estes resultados mostram que ExoU ativa a produção de espécies reativas de oxigênio e nitrogênio, levando à peroxidação lipídica e modulando o sistema de defesa antioxidante

A study of indium incorporation in In-rich InGaN grown by MOVPE

InGaN/GaN heterostructures have been deposited onto (0 0 0 1) sapphire by our home-made low pressure MOVPE with different growth parameters. It has been noted that the indium incorporation depends by a complex way on a number of factors. In this work, the effect of substrate temperature, trimethylindium input flow and V/III ratio on the indium incorporation has been investigated. Finally, by optimizing the growth parameters, we made a series of single-phase InGaN samples with indium content from 10% up to 45%.

Consequências do trabalho por turnos e nocturno em profissionais de enfermagem (estudo realizado em dois hospitais do norte de Portugal)

Dissertação de Mestrado apresentada à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Mestre em Psicologia.

Plasma levels of the immunomodulatory cytokine interleukin-10 during normal human pregnancy: a longitudinal study.

Pregnancy is proposed to be a Th2 phenomenon, where Th2 cytokines inhibit Th1 responses to improve fetal survival. The importance of interleukin-10 (IL-10), an immunomodulatory cytokine produced by Th2 cells, in the maintenance of normal pregnancy is becoming increasingly apparent. In a longitudinal case-control study, the physiological effect of pregnancy on plasma IL-10 was investigated. The plasma concentration of IL-10 was determined using an ELISA technique in 99 pregnant women sampled at 12, 20 and 35 weeks of gestation, 38 non-pregnant control subjects sampled in parallel and in a subgroup of women sampled at 3 days post-partum (n, pregnant 21, non-pregnant 21). Plasma IL-10 was significantly higher in pregnant women at 12, 20 and 35 weeks of gestation (p