Reconfigurable weblabs based on the IEEE1451 Std

Technology plays a double role in Education: it can act as a facilitator in the teaching/learning process and it can be the very subject of that process in Science & Engineering courses. This is especially true when students perform laboratory activities where they interact with equipment and objects under experimentation. In this context, technology can also play a facilitator role if it allows students to perform experiments in a remote fashion, through the Internet, in a so-called weblab or remote laboratory. No doubt, the Internet has been revolutionizing the educational process in many aspects, and it can be stated that remote laboratories are just an angle of that on-going revolution. As any other educational tool or resource, the i) pedagogical approach and the ii) technology used in the development of a remote laboratory can dictate its general success or its ephemeral existence. By pedagogical approach we consider the way remote experiments address the process by which students acquire experimental skills and link experimental results to theoretical concepts. In respect to technology, we discuss different specification and implementation alternatives, to show the case where the adoption of a family of standards would positively contribute to a larger acceptance and utilization of remote laboratories, and also to a wider collaboration in their development.

Compact, frequency reconfigurable, printed monopole antenna

This paper proposes a possible implementation of a compact printed monopole antenna, useful to operate in UMTS and WLAN bands. In order to accomplish that, a miniaturization technique based on the application of chip inductors is used in conjunction with frequency reconfiguration capability. The chip inductors change the impedance response of the monopole, allowing to reduce the resonant frequency. In order to be able to operate the antenna in these two different frequencies, an antenna reconfiguration technique based on PIN diodes is applied. This procedure allows the change of the active form of the antenna leading to a shift in the resonant frequency. The prototype measurements show good agreement with the simulation results.

Peers' evaluation of a reconfigurable IEEE1451.0-compliant and FPGA-based weblab

It is already more than 10 years that weblabs are seen as important resources to provide the experimental work required in engineering education. Several weblabs have been applied in engineering courses, but there are still unsolved problems related to the development of their infrastructures. For solving some of those problems, it was implemented a weblab with a reconfigurable infrastructure compliant with the IEEE1451.0 Std. and supported by Field Programmable Gate Array (FPGA) technology. This paper presents the referred weblab, and provides and analyses a set of researchers' opinions about the implemented infrastructure, and the adopted methodology for the conduction of real experiments.

Reliability and availability in reconfigurable computing: a basis for a common solution

Dynamically reconfigurable SRAM-based field-programmable gate arrays (FPGAs) enable the implementation of reconfigurable computing systems where several applications may be run simultaneously, sharing the available resources according to their own immediate functional requirements. To exclude malfunctioning due to faulty elements, the reliability of all FPGA resources must be guaranteed. Since resource allocation takes place asynchronously, an online structural test scheme is the only way of ensuring reliable system operation. On the other hand, this test scheme should not disturb the operation of the circuit, otherwise availability would be compromised. System performance is also influenced by the efficiency of the management strategies that must be able to dynamically allocate enough resources when requested by each application. As those resources are allocated and later released, many small free resource blocks are created, which are left unused due to performance and routing restrictions. To avoid wasting logic resources, the FPGA logic space must be defragmented regularly. This paper presents a non-intrusive active replication procedure that supports the proposed test methodology and the implementation of defragmentation strategies, assuring both the availability of resources and their perfect working condition, without disturbing system operation.

Embedding instruments & modules into an IEEE1451-FPGA-Based Weblab infrastructure

Adopting standard-based weblab infrastructures can be an added value for spreading their influence and acceptance in education. This paper suggests a solution based on the IEEE1451.0 Std. and FPGA technology for creating reconfigurable weblab infrastructures using Instruments and Modules (I&Ms) described through standard Hardware Description Language (HDL) files. It describes a methodology for creating and binding I&Ms into an IEEE1451-module embedded in a FPGA-based board able to be remotely controlled/accessed using IEEE1451-HTTP commands. At the end, an example of a step-motor controller module bond to that IEEE1451-module is described.

Control of a 6-DOF parallel manipulator through a mechatronic approach

This paper shows that a hierarchical architecture, distributing several control actions in growing levels of complexity and using resources of reconfigurable computing, enables one to take into account the ease of future modifications, updates and improvements in robotic applications. An experimental example of a Stewart—Gough platform control (a platform applied as the solution to countless practical problems) is presented using reconfigurable computing. The software and hardware developed are structured in independent blocks. This open architecture implementation allows easy expansion of the system and better adaptation of the platform to its related tasks.

On-line self-healing of circuits implemented on reconfigurable FPGAs

To boost logic density and reduce per unit power consumption SRAM-based FPGAs manufacturers adopted nanometric technologies. However, this technology is highly vulnerable to radiation-induced faults, which affect values stored in memory cells, and to manufacturing imperfections. Fault tolerant implementations, based on Triple Modular Redundancy (TMR) infrastructures, help to keep the correct operation of the circuit. However, TMR is not sufficient to guarantee the safe operation of a circuit. Other issues like module placement, the effects of multi- bit upsets (MBU) or fault accumulation, have also to be addressed. In case of a fault occurrence the correct operation of the affected module must be restored and/or the current state of the circuit coherently re-established. A solution that enables the autonomous restoration of the functional definition of the affected module, avoiding fault accumulation, re-establishing the correct circuit state in real-time, while keeping the normal operation of the circuit, is presented in this paper.

A framework for self-healing radiation-tolerant implementations on reconfigurable FPGAs

To increase the amount of logic available in SRAM-based FPGAs manufacturers are using nanometric technologies to boost logic density and reduce prices. However, nanometric scales are highly vulnerable to radiation-induced faults that affect values stored in memory cells. Since the functional definition of FPGAs relies on memory cells, they become highly prone to this type of faults. Fault tolerant implementations, based on triple modular redundancy (TMR) infrastructures, help to keep the correct operation of the circuit. However, TMR is not sufficient to guarantee the safe operation of a circuit. Other issues like the effects of multi-bit upsets (MBU) or fault accumulation, have also to be addressed. Furthermore, in case of a fault occurrence the correct operation of the affected module must be restored and the current state of the circuit coherently re-established. A solution that enables the autonomous correct restoration of the functional definition of the affected module, avoiding fault accumulation, re-establishing the correct circuit state in realtime, while keeping the normal operation of the circuit, is presented in this paper.

A framework for fault tolerant real time systems based on reconfigurable FPGAs

To increase the amount of logic available to the users in SRAM-based FPGAs, manufacturers are using nanometric technologies to boost logic density and reduce costs, making its use more attractive. However, these technological improvements also make FPGAs particularly vulnerable to configuration memory bit-flips caused by power fluctuations, strong electromagnetic fields and radiation. This issue is particularly sensitive because of the increasing amount of configuration memory cells needed to define their functionality. A short survey of the most recent publications is presented to support the options assumed during the definition of a framework for implementing circuits immune to bit-flips induction mechanisms in memory cells, based on a customized redundant infrastructure and on a detection-and-fix controller.

On-line defragmentation for run-time partially reconfigurable FPGAs

Dynamically reconfigurable systems have benefited from a new class of FPGAs recently introduced into the market, which allow partial and dynamic reconfiguration at run-time, enabling multiple independent functions from different applications to share the same device, swapping resources as needed. When the sequence of tasks to be performed is not predictable, resource allocation decisions have to be made on-line, fragmenting the FPGA logic space. A rearrangement may be necessary to get enough contiguous space to efficiently implement incoming functions, to avoid spreading their components and, as a result, degrading their performance. This paper presents a novel active replication mechanism for configurable logic blocks (CLBs), able to implement on-line rearrangements, defragmenting the available FPGA resources without disturbing those functions that are currently running.

A new approach to assess defragmentation strategies in dynamically reconfigurable FPGAs

Fragmentation on dynamically reconfigurable FPGAs is a major obstacle to the efficient management of the logic space in reconfigurable systems. When resource allocation decisions have to be made at run-time a rearrangement may be necessary to release enough contiguous resources to implement incoming functions. The feasibility of run-time relocation depends on the processing time required to set up rearrangements. Moreover, the performance of the relocated functions should not be affected by this process or otherwise the whole system performance, and even its operation, may be at risk. Relocation should take into account not only specific functional issues, but also the FPGA architecture, since these two aspects are normally intertwined. A simple and fast method to assess performance degradation of a function during relocation and to speed up the defragmentation process, based on previous function labelling and on the application of the Euclidian distance concept, is proposed in this paper.

Reconfigurable antenna for mobile terminal

Trabalho Final de Mestrado para obtenção do grau de Mestrado em Engenharia Electrónica e Telecomunicações

ALS-Sence: sistema de aquisição e processamento de electromiogramas para pacientes com ALS

Dissertação para obtenção do grau de Mestre em Engenharia de Eletrónica e Computadores

Sparse matrix multiplication on a reconfigurable many-core architecture

Sparse matrix-vector multiplication (SMVM) is a fundamental operation in many scientific and engineering applications. In many cases sparse matrices have thousands of rows and columns where most of the entries are zero, while non-zero data is spread over the matrix. This sparsity of data locality reduces the effectiveness of data cache in general-purpose processors quite reducing their performance efficiency when compared to what is achieved with dense matrix multiplication. In this paper, we propose a parallel processing solution for SMVM in a many-core architecture. The architecture is tested with known benchmarks using a ZYNQ-7020 FPGA. The architecture is scalable in the number of core elements and limited only by the available memory bandwidth. It achieves performance efficiencies up to almost 70% and better performances than previous FPGA designs.

System-on-chip field-programmable gate array design for onboard real-time hyperspectral unmixing

Hyperspectral instruments have been incorporated in satellite missions, providing large amounts of data of high spectral resolution of the Earth surface. This data can be used in remote sensing applications that often require a real-time or near-real-time response. To avoid delays between hyperspectral image acquisition and its interpretation, the last usually done on a ground station, onboard systems have emerged to process data, reducing the volume of information to transfer from the satellite to the ground station. For this purpose, compact reconfigurable hardware modules, such as field-programmable gate arrays (FPGAs), are widely used. This paper proposes an FPGA-based architecture for hyperspectral unmixing. This method based on the vertex component analysis (VCA) and it works without a dimensionality reduction preprocessing step. The architecture has been designed for a low-cost Xilinx Zynq board with a Zynq-7020 system-on-chip FPGA-based on the Artix-7 FPGA programmable logic and tested using real hyperspectral data. Experimental results indicate that the proposed implementation can achieve real-time processing, while maintaining the methods accuracy, which indicate the potential of the proposed platform to implement high-performance, low-cost embedded systems, opening perspectives for onboard hyperspectral image processing.