Design and fabrication of color filters for projection display system

Color filters are key components in an optical engine projection display system. In this paper, a new admittance-matching method for designing and fabricating the high performance filters is described, in which the optimized layers are limited to the interfaces between the stack (each combination of quarter-wave-optical-thickness film layers is called a stack) and stack, or between stack and substrate, or between stack and incident medium. This method works well in designing filters containing multiple stacks such as UV-IR cut and broadband filters. The tolerance and angle sensitivity for the designed film stacks are analyzed. The thermal stability of the sample color filters was measured. A good result in optical performance and thermal stability was obtained through the new design approach. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

Analysis of channel quality reporting mechanisms and their impact into 4G and beyond technologies

206 p.

Arctic charr from Ennerdale Water: a pilot study

There are three fish species in the north west of England, Arctic charr (Salvelinus alpinus, L.), schelly (Coreqonus lavaretus. L.), and vendace (C. albula, L.), which have been reported as rare and vulnerable and have been identified as requiring the preparation and implementation of a conservation management plan. The presence of Arctic charr in Ennerdale Water has resulted in it being designated as a Site of Special Scientific Interest. These fish and one race of the species in Lake Windermere are the only English populations of charr known to spawn in running water. Associated with Ennerdale charr is the copepod parasite Salmincola edwardsii which has not been recorded from any other charr inhabited waters of the Lake District. However, it has been recorded on charr from four Scottish Lochs (Stack, Lee, Tay and Doon). The unique nature of Ennerdale is further highlighted by the presence of two crustaceans, Mysis relicta and Limnocalanus macrurus. The former has been recorded in Ireland while the latter is not known to exist anywhere else in the British Isles. The aim of this pilot study was to obtain baseline data on charr that spawn in Smithy Beck and the River Liza. This would indicate the current status of the population and help identify areas requiring further investigation. A total of 161 fish (95 males and 66 females) was caught and tagged over the 3 day period, 141 from Smithy Beck and 20 from the Liza. The raw data of the findings is presented in two appendices.

Design and properties analysis of multi-layer dielectric used in pulse compressor gratings

Used in chirped-pulse amplification system and based on multi-layer thin film stack, pulse compressor gratings (PCG) are etched by ion-beam and holographic techniques. Diffraction efficiency and laser-induced damage threshold rely on the structural parameters of gratings. On the other hand, they depend greatly on the design of multi-layer. A theoretic design is given for dielectric multi-layer, which is exposed at 413.1 nm and used at 1053 nm. The influences of coating design on optical characters are described in detail. The analysis shows that a coating stack of H3L (H2L) (boolean AND) 9H0.5L2.01H meets the specifications of PCG well. And there is good agreement of transmission between experimental and the theoretic design. (c) 2005 Elsevier GmbH. All rights reserved.

脉宽压缩光栅用的多层膜设计和性能分析

应用于啁啾脉冲放大技术中的脉宽压缩光栅是基于多层膜作为基底，利用全息干涉技术和离子束技术刻蚀而成。脉宽压缩光栅的衍射效率和抗激光损伤阈值一方面依赖于光栅结构的设计，另一方面很大程度上取决于作为基底的多层膜的设计。给出了以413．1nm作为写入波长，1053nm作为使用波长的多层介质光栅膜的设计．样品在ZZS-800F、型真空镀膜机上采用电子束蒸发方式沉积而成，并给出了膜系结构对光学性能影响因素的详细分析，结果表明膜系H3L(H2L)^9H0．5L2．03H满足光栅膜的指标。给出了样品光学特性测试，其使用波

Design of anisotropic reflector with birefringent thin films

A novel design for dielectric anisotropic mirrors with birefringent thin films for normal incidence is presented. This mirror consists of a stack of quarter-wave biaxial layers. The biaxial anisotropic layers can be fabricated by oblique deposition. The reflectance is different for two linear polarizations of light incidence on the mirrors. As a numerical example, the design is carried out on glass with TiO2 and ZrO2. These thin films could be applied to anisotropic reflective devices for lasers.

飞秒激光用多层介质膜脉宽压缩光栅的设计

以薄膜光学的干涉理论和衍射光学的傅里叶模式理论为基础，给出了0．8μm飞秒激光器用多层介质膜脉宽压缩光栅的理论设计；设计采用H3L（HL）^9H0．5L2．4H的多层介质膜为基底，当刻蚀后表面浮雕结构的占宽比为0．35，线密度为1480线／mm，槽深为0．2μm，顶层HfO2的剩余厚度为0．15μm时，对于Littrow角度（36．7°）和TE波模式入射的衍射光栅其-1级衍射效率达到95％以上．

Design and fabrication of color filters for projection display system

Color filters are key components in an optical engine projection display system. In this paper, a new admittance-matching method for designing and fabricating the high performance filters is described, in which the optimized layers are limited to the interfaces between the stack (each combination of quarter-wave-optical-thickness film layers is called a stack) and stack, or between stack and substrate, or between stack and incident medium. This method works well in designing filters containing multiple stacks such as UV-IR cut and broadband filters. The tolerance and angle sensitivity for the designed film stacks are analyzed. The thermal stability of the sample color filters was measured. A good result in optical performance and thermal stability was obtained through the new design approach. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

1064nm倍频波长分离膜的制备与性能研究

通过对主膜系添加匹配层并借助计算机对膜系进行优化，设计出结构规整、性能优良的1064ilm倍频波长分离膜。用电子束蒸发及光电极值监控技术在K9玻璃基底上沉积薄膜，将样品置于空气中在260℃温度下进行3h热退火处理。然后用Lambda 900分光光度计测量了样品的光谱性能；用表面热透镜(STL)技术测量了样品的弱吸收值；用调Q脉冲激光装置测试了样品的抗激光损伤阈值(LIDT)。实验结果发现，样品的实验光谱性能与理论光谱性能有很好的一致性。退火前后其光谱性能几乎没有发生温漂，说明薄膜的温度稳定性好；同时退火使

LBO晶体上1064，532nm倍频增透膜的镀制及性能分析

用电子束蒸发沉积方法在X切LBO（X-LBO）晶体上镀制了两种不同膜系结构的1064和532nm倍频增透膜，其中一种膜系结构为基底／ZrO2／Y2O3／A12O3／SiO2／空气，另一种为基底／0．5Al2O3／ZrO2／Y2O3／A12O3／SiO2／空气，两种膜系结构的主要差别在于有无氧化铝过渡层。测量了薄膜的反射率光谱曲线，发现两种增透膜在1064和532nm处的反射率均小于0．5％，实际镀制结果与理论设计曲线的差异主要是由材料折射率的变化引起的。且对样品在空气环境中进行了温度为473K的退火处理，

渐变折射率薄膜的分层评价探讨

首先阐述了将渐变折射率薄膜细分为多层均匀薄膜的分层介质理论，接着给出了一种获得最佳分层数目的分层评价方法，最后以线性变化渐变折射率薄膜为例说明了如何优化获得渐变折射率薄膜的分层数目．研究发现：渐变折射率薄膜的分层数目与薄膜的厚度和薄膜的折射率变化快慢有关，在一定的折射率变化范围内，渐变折射率薄膜的分层数目随着薄膜厚度的增加先减小后增大．

反射型导模共振滤波器设计

导模共振滤波器由于其高峰值反射率,低旁带反射,窄带以及带宽可控等优良特性引起了人们极大的关注,采用亚波长光栅的导模共振效应可以实现传统基于高低折射率介质的多层膜滤波器所无法实现的特殊功能,在弱调制模式下,其共振带宽可以被压缩到零点几纳米,但是由于介质表面和空气层的菲涅耳反射,使得偏离或者远离共振区时的反射率偏高,根据等效介质理论,亚波长光栅在远离共振区可以被看为均匀的薄膜,本文通过对导模共振光栅进行单层、双层以及三层抗反射设计,有效的降低了导模共振光栅的旁带反射率,从而在可见光波段获得了性能优良的共振滤波器.

引入过渡层提高介质减反膜的抗激光损伤阈值

提出了一种用于提高介质减反膜的损伤阈值的新的方法，在H2.5L (H:HfO2, L:SiO2)的膜层与基底之间引入4个1/4光学厚度的SiO2薄膜，发现抗激光损伤阈值提高了50%，并且保持1064nm处的反射率低于0.09%。本文分析了造成这一提高的机制，一定厚度的氧化硅过渡层的引入是一种提高介质减反膜的损伤阈值的灵活有效的方法。