Experiments of a diode-pumped Nd : GdVO4/LT-GaAs Q-switched and mode-locked laser

A diode-pumped passively Q-switched mode-locked (QML) Nd:GdVO4 laser with a low temperature GaAs (LT-GaAs) saturable absorber is presented. The maximal Q-switched mode-locked average output power was 798 mW with the Q-switched envelop having a repetition rate of 125 kHz. The mode-locked pulse trains inside the Q-switched pulse envelope had a repetition rate of similar to 750 MHz. The laser properties of the operational parameters on the pump power were also investigated experimentally.

Broad-band semiconductor optical amplifiers

Broad-band semiconductor optical amplifiers (SOAs) with different thicknesses and thin bulk tensile-strained active layers were fabricated and studied. Amplified spontaneous emission (ASE) spectra and gain spectra of SOAs were measured and analyzed at different CW biases. A maximal 3 dB ASE bandwidth of 136 nm ranging from 1480 to 1616 nm, and a 3 dB optical amplifier gain bandwidth of about 90 nm ranging from 1510 to 1600 nm, were obtained for the very thin bulk active SOA. Other SOAs characteristics such as saturation output power and polarization sensitivity were measured and compared. (c) 2006 Elsevier B.V. All rights reserved.

Experimental investigation of intracavity absorber low temperature GaAs in diode-pumped Nd : GdVO4 laser

A passively Q-switched and mode-locked diode-pumped Nd:GdVO4 laser was demonstrated using a low-temperature-grown GaAs wafer (LT-GaAs) as an intracavity saturable absorber. The maximal Q-switched mode-locked average output power was 750 mW with the Q-switched envelop having a repetition rate of 167 kHz. The mode-locked pulse trains inside the Q-switched pulse envelope had a repetition rate of similar to 790 MHz.

Finite element analysis of stress and strain distributions in InAs/GaAs quantum dots

In this paper, we perform systematic calculations of the stress and strain distributions in InAs/GaAs truncated pyramidal quantum dots (QDs) with different wetting layer (WL) thickness, using the finite element method (FEM). The stresses and strains are concentrated at the boundaries of the WL and QDs, are reduced gradually from the boundaries to the interior, and tend to a uniform state for the positions away from the boundaries. The maximal strain energy density occurs at the vicinity of the interface between the WL and the substrate. The stresses, strains and released strain energy are reduced gradually with increasing WL thickness. The above results show that a critical WL thickness may exist, and the stress and strain distributions can make the growth of QDs a growth of strained three-dimensional island when the WL thickness is above the critical value, and FEM can be applied to investigate such nanosystems, QDs, and the relevant results are supported by the experiments.

Accurate mode analysis of ultraviolet-written channel waveguides

The transfer matrix method combined with the effective index method is adopted to model the silica-based channel waveguide patterned by UV writing. The effective indexes of the graded index channel waveguides with different dimension are calculated. The maximal error of the effective index is less than 3 x 10(-5). By this method, the number of the guided mode and the dimension range to guide certain modes can be obtained easily. Finally, the dimension range to guide a single mode is presented. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

The photon scanning tunneling microscope and its applications

A simple photon scanning tunneling microscope (PSTM) is described. Its lateral resolution (similar to 10nm with a maximal scanning range of 10 mu m x 10 mu m ) is much better than that of a conventional optical microscope. Its principle, the fiber optic tip fabrication and PSTM images of different samples such as mica, HDPE and LiNbO3 are presented.

A 5GHz low power WLAN transceiver SiGe RFIC for personal communication terminal applications

A low-cost low-power single chip WLAN 802.11a transceiver is designed for personal communication terminal and local multimedia data transmission. It has less than 130mA current dissipation, maximal 67dB gain and can be programmed to be 20dB minimal gain. The receiver system noise figure is 6.4dB in hige-gain mode.

A Novel 0.72-6.2GHz Continuously-Tunable Delta Sigma Fractional-N Frequency Synthesizer

This paper presents a wideband Delta Sigma-based fractional-N synthesizer with three integrated quadrature VCOs for multiple-input multiple-output (MIMO) wireless communication applications. It continuously covers a wide range frequency from 0.72GHz to 6.2GHz that is suitable for multiple communication standards. The synthesizer is designed in 0.13-um RE CMOS process. The dual clock full differential multi-modulus divide (MMD) with low power consumption can operate over 9GHz under the worst condition. In the whole range frequency from 0.72GHz to 6.2GHz, the maximal tuning range of the QVCOs reaches 33.09% and their phase noise is -119d8/Hz similar to 124d8/Hz @1MHz. Its current is less than 12mA at a 1.2V voltage supply when it operates at the highest frequency of 6.2GHz.

Vacuum pyrolysis of waste tires with basic additives

Granules of waste tires were pyrolyzed tinder vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na2CO3, NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 degrees C to 600 degrees C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 degrees C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 degrees C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) similar to 205 degrees C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt% which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na2CO3 addition. Pyrolysis gas was mainly composed of H-2, CO, CH4, CO2, C2H4 and C2H6. Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher.

Transverse trapping forces of focused Gaussian beam on ellipsoidal particles

A modified T-matrix method is presented to compute the scattered fields of various realistically shaped particles; then the radiation forces on the particles can be calculated via the Maxwell stress tenser integral. Numerical results of transverse trapping efficiencies of a focused Gaussian beam on ellipsoidal and spherical particles with the same volume are compared, which show that the shape and orientation of particles affect the maximal transverse trapping force and the displacement corresponding to the maximum. The effect of the polarization direction of the incident beam on the transverse trapping forces is also revealed. (c) 2007 Optical Society of America.

横断山区果蝇科的区系分类及伊米果蝇种组各种亚组间的系统发育关系研究

本文新种部分，记述了分布在横断山地区、台湾以及苏门答腊、菲律宾等地果蝇科的新种55种，异物同名3种。在果蝇属果蝇亚属的伊米果蝇种组建立了一个新的种复组－弯头果蝇种亚组(Drosophila curviceps species subgroup)；在quadrilineata种亚组内建立了一个新的种复组－背条果蝇种复组(Drosophila notostriata species-complex)。对横断山地区的果蝇进行研究，计有119个种，主要由东洋种、古北种、特有种和广布种组成；对其渊源关系进行分析。运用分支分类学的观点和方法对伊米果蝇种组中5个种亚组间的系统发育进行研究显示，hypocausta种亚组最原始，位地分支图的最底部，是外群向伊米果蝇种组过渡的一个类群，进化中心在热带的苏门答腊及其附近；其次分化的immigrans种亚组其进化中心仍在热带的苏门答腊及其附近；但该亚组的特种逐渐向北扩散，在中国云南的西双版纳及其附近地区形成次级进化中心。伊米果蝇种组总的进化方向是从热带向温带的逐渐演化。

Effect of Mesa Size on Thermal Characteristics of Vertical-cavity Surface-emitting Lasers

The effect of mesa size on the thermal characteristics of etched mesa vertical-cavity surfaceemitting lasers(VCSELs) is studied. The numerical results show that the mesa size of the top mirror strongly influences the temperature distribution inside the etched mesa VCSEL. Under a certain driving voltage, with decreasing mesa size, the location of the maximal temperature moves towards the p-contact metal, the temperature in the core region of the active layer rises greatly, and the thermal characteristics of the etched mesa VCSELs will deteriorate.

3μm GaInNAs/GasAs Quantum Well Resonant Cavity Enhanced Photodetector

A 1.3μm GaInNAs resonant cavity enhanced (RCE) photodetector (PD) has been grown by molecular beam epitaxy (MBE) monolithically on (100) GaAs substrate using a home-made ion-removed dc-plasma cell as nitrogen source. A transfer matrix method was used to optimize the device structure. The absorption region is composed of three GaInNAs quantum wells separated by GaAs layers. Devices were isolated by etching 130μm-diameter mesas and filling polyamide into grooves. The maximal quantum efficiency of the device is about 12% at 1.293μm. Full width at half maximum (FWHM) is 5.8nm and 3dB bandwidth is 304MHz. Dark current is 2 * 10~(-11) A at zero bias voltage. Further improvement of the performance of the RCE PD can be obtained by optimizing of the structure design and MBE growth conditions.

Analysis of orthogonal memory patterns

It is well known that the storage capacity may be large if all memory patterns are orthogonal to each other. In this paper, a clear description is given about the relation between the dimension N and the maximal number of orthogonal vectors with components +/-1, and also the conception of attractive index is proposed to estimate the basin of attraction. Theoretic analysis and computer simulation show that each memory pattern's basin of attraction contains at least one Hamming ball when the storage capacity is less than 0.33N which is better than usual 0.15 N.

The photon scanning tunneling microscope and its applications

A simple photon scanning tunneling microscope (PSTM) is described. Its lateral resolution (similar to 10nm with a maximal scanning range of 10 mu m x 10 mu m ) is much better than that of a conventional optical microscope. Its principle, the fiber optic tip fabrication and PSTM images of different samples such as mica, HDPE and LiNbO3 are presented.