Luminescence quantum efficiency at 1.5 µm of Er3+- doped tellurite glass determined by thermal lens spectroscopy

Erbium doped tellurite glasses (TeO2 + Li2O + TiO2) were prepared by conventional melt-quenching method to study the influence of the Er3+ concentration on the luminescence quantum efficiency (η) at 1.5 µm. Absorption and luminescence data were used to characterize the samples, and the η parameter was measured using the well-known thermal lens spectroscopy. For low Er3+ concentration, the measured values are around 76%, and the concentration behavior of η shows Er-Er and Er-OH- interactions, which agreed with the measured lifetime values.

Photocatalytic activity of nanostructured anatase coatings obtained by cold gas spray

[EN] This article describes a photocatalytic nanostructured anatase coating deposited by cold gas spray (CGS) supported on titanium sub-oxide (TiO22x) coatings obtained by atmospheric plasma spray (APS) onto stainless steel cylinders. The photocatalytic coating was homogeneous and preserved the composition and nanostructure of the starting powder. The inner titanium sub-oxide coating favored the deposition of anatase particles in the solid state. Agglomerated nano-TiO2 particles fragmented when impacting onto the hard surface of the APS TiO22x bond coat. The rough surface provided by APS provided an ideal scenario for entrapping the nanostructured particles, which may be adhered onto the bond coat due to chemical bonding; a possible bonding mechanism is described. Photocatalytic experiments showed that CGS nano-TiO2 coating was active for photodegrading phenol and formic acid under aqueous conditions. The results were similar to the performance obtained by competitor technologies and materials such as dip-coating P25 photocatalysts. Disparity in the final performance of the photoactive materials may have been caused by differences in grain size and the crystalline composition of titanium dioxide.

Eliminación de microcontaminantes orgánicos mediante tratamientos avanzados para un uso potable indirecto de aguas regeneradas

[ES]En este trabajo se ha evaluado la utilización de procesos avanzados en la obtención de agua regenerada para un uso potable indirecto. Se ha investigado la eficacia de procesos de oxidación avanzada (UV/H2O2) y (UV/TiO2), así como de adsorción sobre carbón activado, en la eliminación de 23 fármacos presentes habitualmente en aguas tratadas por tratamientos convencionales en EDAR urbanas, en concentraciones del orden de ng/L. El tratamiento con UVC y H2O2 resultó ser más eficiente que la fotocatálisis con TiO 2, ya que elimina el 100% de los fármacos estudiados. La presencia de materia orgánica y bicarbonato en agua microfiltrada procedente de un tratamient o de lodos activados, limitan la aplicación de la fotocatálisis heterogénea debido al envenenamiento de la superficie del catalizador así como a una competencia de los componentes del agua y los contaminantes en las reacciones con las especies oxidantes generada.

Processo biotecnologico a cellule immobilizzate per la produzione di acidi grassi volatili da acque di vegetazione

Le acque di vegetazione (AV) costituiscono un serio problema di carattere ambientale, sia a causa della loro elevata produzione sia per l’ elevato contenuto di COD che oscilla fra 50 e 150 g/l. Le AV sono considerate un refluo a tasso inquinante fra i più elevati nell’ambito dell’industria agroalimentare e la loro tossicità è determinata in massima parte dalla componente fenolica. Il presente lavoro si propone di studiare e ottimizzare un processo non solo di smaltimento di tale refluo ma anche di una sua valorizzazione, utlizzandolo come materia prima per la produzione di acidi grassi e quindi di PHA, polimeri biodegradabili utilizzabili in varie applicazioni. A tale scopo sono stati utilizzati due bioreattori anaerobici a biomassa adesa, di identica configurazione, con cui si sono condotti due esperimenti in continuo a diverse temperature e carichi organici al fine di studiare l’influenza di tali parametri sul processo. Il primo esperimento è stato condotto a 35°C e carico organico pari a 12,39 g/Ld, il secondo a 25°C e carico organico pari a 8,40 g/Ld. Si è scelto di allestire e mettere in opera un processo a cellule immobilizzate in quanto questa tecnologia si è rivelata vantaggiosa nel trattamento continuo di reflui ad alto contenuto di COD e carichi variabili. Inoltre si è scelto di lavorare in continuo poiché tale condizione, per debiti tempi di ritenzione idraulica, consente di minimizzare la metanogenesi, mediata da microrganismi con basse velocità specifiche di crescita. Per costituire il letto fisso dei due reattori si sono utilizzati due diversi tipi di supporto, in modo da poter studiare anche l’influenza di tale parametro, in particolare si è fatto uso di carbone attivo granulare (GAC) e filtri ceramici Vukopor S10 (VS). Confrontando i risultati si è visto che la massima quantità di VFA prodotta nell’ambito del presente studio si ha nel VS mantenuto a 25°C: in tale condizione si arriva infatti ad un valore di VFA prodotti pari a 524,668 mgCOD/L. Inoltre l’effluente in uscita risulta più concentrato in termini di VFA rispetto a quello in entrata: nell’alimentazione la percentuale di materiale organico presente sottoforma di acidi grassi volatili era del 54 % e tale percentuale, in uscita dai reattori, ha raggiunto il 59 %. Il VS25 rappresenta anche la condizione in cui il COD degradato si è trasformato in percentuale minore a metano (2,35 %) e questo a prova del fatto che l’acidogenesi ha prevalso sulla metanogenesi. Anche nella condizione più favorevole alla produzione di VFA però, si è riusciti ad ottenere una loro concentrazione in uscita (3,43 g/L) inferiore rispetto a quella di tentativo (8,5 g/L di VFA) per il processo di produzione di PHA, sviluppato da un gruppo di ricerca dell’università “La Sapienza” di Roma, relativa ad un medium sintetico. Si può constatare che la modesta produzione di VFA non è dovuta all’eccessiva degradazione del COD, essendo questa nel VS25 appena pari al 6,23%, ma piuttosto è dovuta a una scarsa concentrazione di VFA in uscita. Questo è di buon auspicio nell’ottica di ottimizzare il processo migliorandone le prestazioni, poiché è possibile aumentare tale concentrazione aumentando la conversione di COD in VFA che nel VS25 è pari a solo 5,87%. Per aumentare tale valore si può agire su vari parametri, quali la temperatura e il carico organico. Si è visto che il processo di acidogenesi è favorito, per il VS, per basse temperature e alti carichi organici. Per quanto riguarda il reattore impaccato con carbone attivo la produzione di VFA è molto ridotta per tutti i valori di temperatura e carichi organici utilizzati. Si può quindi pensare a un’applicazione diversa di tale tipo di reattore, ad esempio per la produzione di metano e quindi di energia.

Caratterizzazione di membrane da nanofiltrazione

Nanofiltration (NF) is a pressure-driven membrane process, intermediate between reverse osmosis and ultrafiltration. Commercially available polymeric membranes have been used in a wide range of applications, such as drinking, process industry and waste water treatment. For all the applications requiring high stability and harsh washing procedures inorganic membranes are preferred due to their high chemical inertia. Typically, γ – Al2O3 as well as TiO2 and ZrO2 selective layers are used; the latter show higher chemical stability in a wide range of pH and temperatures. In this work the experimental characterization of two different type of membrane has been performed in order to investigate permeation properties, separation performance and efficiency with aqueous solutions containing strong inorganic electrolytes. The influence of salt concentration and feed pH as well as the role of concentration polarization and electrolyte type on the membrane behavior are investigated. Experimentation was performed testing a multi–layer structured NF membrane in α-Al2O3, TiO2 and ZrO2, and a polymeric membrane, in polyamide supported on polysulfone, with binary aqueous solutions containing NaCl, Na2SO4 or CaCl2; the effect of salt composition and pH in the feed side was studied both on flux and salt rejection. All the NF experimental data available for the two membranes were used to evaluate the volumetric membrane charge (X) corresponding to each operative conditions investigated, through the Donnan Steric Pore Model and Dielectric Exclusion (DSPM&DE). The results obtained allow to understand which are the main phenomena at the basis of the different behaviors observed.

New high nuclearity carbonyl clusters

The thesis reports the synthesis, and the chemical, structural and spectroscopic characterization of a series of new Rhodium and Au-Fe carbonyl clusters. Most new high-nuclearity rhodium carbonyl clusters have been obtained by redox condensation of preformed rhodium clusters reacting with a species in a different oxidation state generated in situ by mild oxidation. In particular the starting Rh carbonyl clusters is represented by the readily available [Rh7(CO)16]3- 9 compound. The oxidized species is generated in situ by reaction of the above with a stoichiometric defect of a mild oxidizing agents such as [M(H2O)x]n+ aquo complexes possessing different pKa’s and Mn+/M potentials. The experimental results are roughly in keeping with the conclusion that aquo complexes featuring E°(Mn+/M) < ca. -0.20 V do not lead to the formation of hetero-metallic Rh clusters, probably because of the inadequacy of their redox potentials relative to that of the [Rh7(CO)16]3-/2- redox couple. Only homometallic cluster s such as have been fairly selectively obtained. As a fallout of the above investigations, also a convenient and reproducible synthesis of the ill-characterized species [HnRh22(CO)35]8-n has been discovered. The ready availability of the above compound triggered both its complete spectroscopic and chemical characterization. because it is the only example of Rhodium carbonyl clusters with two interstitial metal atoms. The presence of several hydride atoms, firstly suggested by chemical evidences, has been implemented by ESI-MS and 1H-NMR, as well as new structural characterization of its tetra- and penta-anion. All these species display redox behaviour and behave as molecular capacitors. Their chemical reactivity with CO gives rise to a new series of Rh22 clusters containing a different number of carbonyl groups, which have been likewise fully characterized. Formation of hetero-metallic Rh clusters was only observed when using SnCl2H2O as oxidizing agent because. Quite all the Rh-Sn carbonyl clusters obtained have icosahedral geometry. The only previously reported example of an icosahedral Rh cluster with an interstitial atom is the [Rh12Sb(CO)27]3- trianion. They have very similar metal framework, as well as the same number of CO ligands and, consequently, cluster valence electrons (CVEs). .A first interesting aspect of the chemistry of the Rh-Sn system is that it also provides icosahedral clusters making exception to the cluster-borane analogy by showing electron counts from 166 to 171. As a result, the most electron-short species, namely [Rh12Sn(CO)25]4- displays redox propensity, even if disfavoured by the relatively high free negative charge of the starting anion and, moreover, behaves as a chloride scavenger. The presence of these bulky interstitial atoms results in the metal framework adopting structures different from a close-packed metal lattice and, above all, imparts a notable stability to the resulting cluster. An organometallic approach to a new kind of molecular ligand-stabilized gold nanoparticles, in which Fe(CO)x (x = 3,4) moieties protect and stabilize the gold kernel has also been undertaken. As a result, the new clusters [Au21{Fe(CO)4}10]5-, [Au22{Fe(CO)4}12]6-, Au28{Fe(CO)3}4{Fe(CO)4}10]8- and [Au34{Fe(CO)3}6{Fe(CO)4}8]6- have been isolated and characterized. As suggested by concepts of isolobal analogies, the Fe(CO)4 molecular fragment may display the same ligand capability of thiolates and go beyond. Indeed, the above clusters bring structural resemblance to the structurally characterized gold thiolates by showing Fe-Au-Fe, rather than S-Au-S, staple motives. Staple motives, the oxidation state of surface gold atoms and the energy of Au atomic orbitals are likely to concur in delaying the insulator-to-metal transition as the nuclearity of gold thiolates increases, relative to the more compact transition-metal carbonyl clusters. Finally, a few previously reported Au-Fe carbonyl clusters have been used as precursors in the preparation of supported gold catalysts. The catalysts obtained are active for toluene oxidation and the catalytic activity depends on the Fe/Au cluster loading over TiO2.

Materiali Ceramici per Edilizia con Funzionalità Fotocatalitica

This thesis wad aimed at the study and application of titanium dioxide photocatalytic activity on ceramic materials. As a matter of fact, photocatalysis is a very promising method to face most of the problems connected with the increasing environmental pollution. Furthermore, titanium dioxide, in its anatase crystallographic phase, is one of the most investigated photocatalytic material and results to be perfectly compatible with silicate body mixes. That goal was pursued by two different strategies: 1. the addition to a body mix used for heavy clay products of several titania powders, with different mean crystallite size, surface area, morphology and anatase/rutile ratio and a titania nanosuspension as well. The titania addition followed two procedures: bulk and spray addition over the ceramic samples surface. Titania was added in two different percentages: 2.5 and 7.5 wt.% in both of the methods. The ceramic samples were then fired at three maximum temperatures: 900, 950 and 1000 °C. Afterwards, the photocatalytic activity of the prepared ceramic samples was evaluated by following the degradation of an organic compound in aqueous medium, under UV radiation. The influence of titania morphological characteristics on the photoactivity of the fired materials was studied by means of XRD and SEM observations. The ceramic samples, sprayed with a slip containing 7.5 wt.% of titania powder and fired at 900 °C, have the best photoactivity, with a complete photo-decomposition of the organic compound. At 1000 °C no sample acted as a photocatalyst due to the anatase-to-rutile phase transformation and to the reaction between titania and calcium and iron oxides in the raw materials. 2. The second one foresaw the synthesis of TiO2-SiO2 solid solutions, using the following stoichiometry: Ti1-xSixO2 where x = 0, 0.1, 0.3 and 0.5 atoms per formula unit (apfu). The mixtures were then fired following two thermal cycles, each with three maximum temperatures. The effect of SiO2 addition into the TiO2 crystal structure and, consequently, on its photocatalytic activity when fired at high temperature, was thoroughly investigated by means of XRD, XPS, FE-SEM, TEM and BET analysis. The photoactivity of the prepared powders was assessed both in gas and liquid phase. Subsequently, the TiO2-SiO2 solid solutions, previously fired at 900 °C, were sprayed over the ceramic samples surface in the percentage of 7.5 wt.%. The prepared ceramic samples were fired at 900 and 1000 °C. The photocatalytic activity of the ceramic samples was evaluated in liquid phase. Unfortunately, that samples did not show any appreciable photoactivity. In fact, samples fired at 900 °C showed a pretty low photoactivity, while the one fired at 1000 °C showed no photoactivity at all. This was explained by the excessive coarsening of titania particles. To summarise, titania particle size, more than its crystalline phase, seems to have a relevant role in the photocatalytic activity of the ceramic samples.

Structural changes and dynamic behaviour of vanadium oxide-based catalysts for gas-phase selective oxidations

Selective oxidation is one of the simplest functionalization methods and essentially all monomers used in manufacturing artificial fibers and plastics are obtained by catalytic oxidation processes. Formally, oxidation is considered as an increase in the oxidation number of the carbon atoms, then reactions such as dehydrogenation, ammoxidation, cyclization or chlorination are all oxidation reactions. In this field, most of processes for the synthesis of important chemicals used vanadium oxide-based catalysts. These catalytic systems are used either in the form of multicomponent mixed oxides and oxysalts, e.g., in the oxidation of n-butane (V/P/O) and of benzene (supported V/Mo/O) to maleic anhydride, or in the form of supported metal oxide, e.g., in the manufacture of phthalic anhydride by o-xylene oxidation, of sulphuric acid by oxidation of SO2, in the reduction of NOx with ammonia and in the ammoxidation of alkyl aromatics. In addition, supported vanadia catalysts have also been investigated for the oxidative dehydrogenation of alkanes to olefins , oxidation of pentane to maleic anhydride and the selective oxidation of methanol to formaldehyde or methyl formate [1]. During my PhD I focused my work on two gas phase selective oxidation reactions. The work was done at the Department of Industrial Chemistry and Materials (University of Bologna) in collaboration with Polynt SpA. Polynt is a leader company in the development, production and marketing of catalysts for gas-phase oxidation. In particular, I studied the catalytic system for n-butane oxidation to maleic anhydride (fluid bed technology) and for o-xylene oxidation to phthalic anhydride. Both reactions are catalyzed by systems based on vanadium, but catalysts are completely different. Part A is dedicated to the study of V/P/O catalyst for n-butane selective oxidation, while in the Part B the results of an investigation on TiO2-supported V2O5, catalyst for o-xylene oxidation are showed. In Part A, a general introduction about the importance of maleic anhydride, its uses, the industrial processes and the catalytic system are reported. The reaction is the only industrial direct oxidation of paraffins to a chemical intermediate. It is produced by n-butane oxidation either using fixed bed and fluid bed technology; in both cases the catalyst is the vanadyl pyrophosphate (VPP). Notwithstanding the good performances, the yield value didn’t exceed 60% and the system is continuously studied to improve activity and selectivity. The main open problem is the understanding of the real active phase working under reaction conditions. Several articles deal with the role of different crystalline and/or amorphous vanadium/phosphorous (VPO) compounds. In all cases, bulk VPP is assumed to constitute the core of the active phase, while two different hypotheses have been formulated concerning the catalytic surface. In one case the development of surface amorphous layers that play a direct role in the reaction is described, in the second case specific planes of crystalline VPP are assumed to contribute to the reaction pattern, and the redox process occurs reversibly between VPP and VOPO4. Both hypotheses are supported also by in-situ characterization techniques, but the experiments were performed with different catalysts and probably under slightly different working conditions. Due to complexity of the system, these differences could be the cause of the contradictions present in literature. Supposing that a key role could be played by P/V ratio, I prepared, characterized and tested two samples with different P/V ratio. Transformation occurring on catalytic surfaces under different conditions of temperature and gas-phase composition were studied by means of in-situ Raman spectroscopy, trying to investigate the changes that VPP undergoes during reaction. The goal is to understand which kind of compound constituting the catalyst surface is the most active and selective for butane oxidation reaction, and also which features the catalyst should possess to ensure the development of this surface (e.g. catalyst composition). On the basis of results from this study, it could be possible to project a new catalyst more active and selective with respect to the present ones. In fact, the second topic investigated is the possibility to reproduce the surface active layer of VPP onto a support. In general, supportation is a way to improve mechanical features of the catalysts and to overcome problems such as possible development of local hot spot temperatures, which could cause a decrease of selectivity at high conversion, and high costs of catalyst. In literature it is possible to find different works dealing with the development of supported catalysts, but in general intrinsic characteristics of VPP are worsened due to the chemical interaction between active phase and support. Moreover all these works deal with the supportation of VPP; on the contrary, my work is an attempt to build-up a V/P/O active layer on the surface of a zirconia support by thermal treatment of a precursor obtained by impregnation of a V5+ salt and of H3PO4. In-situ Raman analysis during the thermal treatment, as well as reactivity tests are used to investigate the parameters that may influence the generation of the active phase. Part B is devoted to the study of o-xylene oxidation of phthalic anhydride; industrially, the reaction is carried out in gas-phase using as catalysts a supported system formed by V2O5 on TiO2. The V/Ti/O system is quite complex; different vanadium species could be present on the titania surface, as a function of the vanadium content and of the titania surface area: (i) V species which is chemically bound to the support via oxo bridges (isolated V in octahedral or tetrahedral coordination, depending on the hydration degree), (ii) a polymeric species spread over titania, and (iii) bulk vanadium oxide, either amorphous or crystalline. The different species could have different catalytic properties therefore changing the relative amount of V species can be a way to optimize the catalytic performances of the system. For this reason, samples containing increasing amount of vanadium were prepared and tested in the oxidation of o-xylene, with the aim of find a correlations between V/Ti/O catalytic activity and the amount of the different vanadium species. The second part deals with the role of a gas-phase promoter. Catalytic surface can change under working conditions; the high temperatures and a different gas-phase composition could have an effect also on the formation of different V species. Furthermore, in the industrial practice, the vanadium oxide-based catalysts need the addition of gas-phase promoters in the feed stream, that although do not have a direct role in the reaction stoichiometry, when present leads to considerable improvement of catalytic performance. Starting point of my investigation is the possibility that steam, a component always present in oxidation reactions environment, could cause changes in the nature of catalytic surface under reaction conditions. For this reason, the dynamic phenomena occurring at the surface of a 7wt% V2O5 on TiO2 catalyst in the presence of steam is investigated by means of Raman spectroscopy. Moreover a correlation between the amount of the different vanadium species and catalytic performances have been searched. Finally, the role of dopants has been studied. The industrial V/Ti/O system contains several dopants; the nature and the relative amount of promoters may vary depending on catalyst supplier and on the technology employed for the process, either a single-bed or a multi-layer catalytic fixed-bed. Promoters have a quite remarkable effect on both activity and selectivity to phthalic anhydride. Their role is crucial, and the proper control of the relative amount of each component is fundamental for the process performance. Furthermore, it can not be excluded that the same promoter may play different role depending on reaction conditions (T, composition of gas phase..). The reaction network of phthalic anhydride formation is very complex and includes several parallel and consecutive reactions; for this reason a proper understanding of the role of each dopant cannot be separated from the analysis of the reaction scheme. One of the most important promoters at industrial level, which is always present in the catalytic formulations is Cs. It is known that Cs plays an important role on selectivity to phthalic anhydride, but the reasons of this phenomenon are not really clear. Therefore the effect of Cs on the reaction scheme has been investigated at two different temperature with the aim of evidencing in which step of the reaction network this promoter plays its role.

Studio di un nuovo processo per la sintesi di acido adipico.

Obiettivo del mio lavoro di tesi è stato quello di verificare la fattibilità di un nuovo processo per la produzione di acido adipico da cicloesene con due stadi di reazione. Il primo stadio di reazione prevede l’ossidazione del cicloesene con soluzione acquosa di acqua ossigenata a formare l’epossido, che idrata a 1,2-cicloesandiolo, mentre nel secondo stadio il glicole viene ossidato con ossigeno ad acido adipico. Il lavoro è stato focalizzato sullo studio del meccanismo di reazione per l’ossidazione del 1,2-cicloesandiolo ad acido adipico, utilizzando catalizzatori a base di Ru(OH)3/Al2O3, Ru(OH)3-Bi(OH)3/Al2O3, Cu/C e Cu/TiO2. Le prove condotte hanno dimostrato che i catalizzatori usati sono attivi nell’ossidazione di 1,2-cicloesandiolo, ma sono caratterizzati da scarsa selettività ad acido adipico. Dall’analisi dei risultati ottenuti si desume che la reazione richiede condizioni fortemente basiche per potere avvenire. In queste condizioni però si vengono a formare degli intermedi che reagiscono rapidamente con l’acqua e con l’ossigeno, dando luogo alla formazione di una serie di prodotti primari e secondari.

Atmospheric corrosion of quaternary bronzes (Cu-Sn-Zn-Pb): laboratory tests (accelerated ageing in wet & dry conditions)and field studies (the Bottego monument in Parma, Italy).

The interactions between outdoor bronzes and the environment, which lead to bronze corrosion, require a better understanding in order to design effective conservation strategies in the Cultural Heritage field. In the present work, investigations on real patinas of the outdoor monument to Vittorio Bottego (Parma, Italy) and laboratory studies on accelerated corrosion testing of inhibited (by silane-based films, with and without ceria nanoparticles) and non-inhibited quaternary bronzes are reported and discussed. In particular, a wet&dry ageing method was used both for testing the efficiency of the inhibitor and for patinating bronze coupons before applying the inhibitor. A wide range of spectroscopic techniques has been used, for characterizing the core metal (SEM+EDS, XRF, AAS), the corroded surfaces (SEM+EDS, portable XRF, micro-Raman, ATR-IR, Py-GC-MS) and the ageing solutions (AAS). The main conclusions were: 1. The investigations on the Bottego monument confirmed the differentiation of the corrosion products as a function of the exposure geometry, already observed in previous works, further highlighting the need to take into account the different surface features when selecting conservation procedures such as the application of inhibitors (i.e. the relative Sn enrichment in unsheltered areas requires inhibitors which effectively interact not only with Cu but also with Sn). 2. The ageing (pre-patination) cycle on coupons was able to reproduce the relative Sn enrichment that actually happens in real patinated surfaces, making the bronze specimens representative of the real support for bronze inhibitors. 3. The non-toxic silane-based inhibitors display a good protective efficiency towards pre-patinated surfaces, differently from other widely used inhibitors such as benzotriazole (BTA) and its derivatives. 4. The 3-mercapto-propyl-trimethoxy-silane (PropS-SH) additivated with CeO2 nanoparticles generally offered a better corrosion protection than PropS-SH.

Un nuovo processo per la sintesi di acroleina e acido acrilico da glicerolo

La trasformazione di glicerolo ad acido acrilico può essere un fattore importante per la valorizzazione del processo di produzione di biodiesel, il quale prevede la coproduzione di enormi quantità di glicerolo. La sintesi di acido acrilico in un unico step è stata studiata attraverso vari catalizzatori solidi bifunzionali di diversa natura, contenenti proprietà acide e redox. I catalizzatori devono avere un’adeguata acidità di Brønsted per promuovere la trasformazione di glicerolo ad acroleina, mentre le proprietà ossidanti, necessarie per la sintesi di acido acrilico sono ottenute mediante l’inserimento di un metallo ossidante nella struttura. Si vuole quindi sintetizzare e testare una serie di catalizzatori che mostrino questa bifunzionalità in grado di soddisfare requisiti di attività e selettività nei confronti della reazioni . Per questo studio sono stati sintetizzati e caratterizzati ossidi misti di W/V, nella forma di aggregati dispersi sulla titania ed ossidi misti di Zr/Nb/V in struttura bulk. Sono stati quindi eseguiti dei test di reattività in fase gas ed in presenza di ossigeno utilizzando un reattore tubolare in quarzo a letto fisso.

Sintesi e caratterizzazione di La0.4Sr0.4TiO3 (LST) come anodo innovativo per celle a combustibile ad ossido solido (SOFC)

Le celle a combustibile ad ossido solido (SOFC) sono reattori elettrochimici che convertono l’energia chimica di un gas combustibile direttamente in energia elettrica con un’alta efficienza e con basse emissioni. Il materiale più comunemente usato come anodo, il Ni/YSZ cermet, mostra però numerosi svantaggi nell’applicazione quali la suscettibilità all’avvelenamento da zolfo e la deposizione di coke per cracking degli idrocarburi usati come combustibile. E’ perciò necessario sviluppare materiali alternativi che sopperiscano a questi problemi. Il titanato di stronzio drogato con lantanio con stechiometria La0.4Sr0.4TiO3 (LST) è stato scelto come anodo alternativo per le ottime proprietà possedute. Lo scopo del lavoro di tesi è stato quindi lo studio dell’influenza della natura dei precursori, delle condizioni di sintesi e dell’aggiunta di agenti porizzanti necessari per l’ottenimento della fase perovskitica pura e con porosità controllata. In un primo tempo è stata verificata la possibilità di ottenere la fase La0.4Sr0.4TiO3 pura mediante sintesi allo stato solido, trattando termicamente miscele di precursori diversi. I risultati ottenuti hanno evidenziato che l’utilizzo di nitrati metallici porta a risultati migliori rispetto all’utilizzo di carbonati ed ossidi poiché permette la formazione della fase perovskite a temperature inferiori e con una purezza maggiore. Poiché l’analisi elementare sui materiali preparati in questa prima fase ha evidenziato un problema sulla stechiometria, il metodo di sintesi è stato ottimizzato solubilizzando preventivamente i precursori di lantanio e stronzio e determinandone il titolo mediante ICP. Inoltre, sono state effettuate delle sintesi utilizzando TiO2 a diversa area superficiale, per verificare l’effetto sulle fasi formate di una maggior reattività di questo componente. Per completezza la perovskite è stata sintetizzata anche tramite sintesi sol-gel, utilizzando il metodo Pechini, ottenendo a 700°C la fase pura. L’analisi morfologica ha evidenziato che le polveri con caratteristiche migliori per la formatura sono quelle ottenute tramite sintesi allo stato solido. Le pastiglie prodotte, miscelando tali polveri e agenti porizzanti opportuni, hanno evidenziato la stabilità della fase perovskitica voluta ma anche la necessità di ottimizzare l’aggiunta del porizzante per avere una porosità adeguata all’applicazione del sistema quale anodo SOFC.

Sintesi di catalizzatori supportati Pd/Cu e studio della loro reattività per l'idrodeclorurazione di molecole clorofluorurate

Il Protocollo di Montreal, che succede alla Convenzione di Vienna per la protezione dello strato di ozono richiede l’eliminazione di idrocarburi contenenti cloro (CFC). Nel corso degli ultimi decenni ha quindi assunto importanza la reazione di idrodeclorurazione di clorofluorocarburi, in particolare rivolta alla produzione di idrocarburi fluorurati che sono risultati interessanti per la produzione di polimeri con specifiche caratteristiche di resistenza meccanica, termica e chimica. In questo lavoro di tesi, svolto in collaborazione con SOLVAY SPECIALTY POLYMERS ITALY, sono stati studiati catalizzatori innovativi per la produzione di perfluorometilviniletere (MVE), mediante idrodeclorurazione di perfluorometilcloroviniletere (AM). Attualmente la reazione di produzione industriale dell’MVE, condotta con l'utilizzo di quantità stechiometriche di Zn e dimetilformammide (DMF), presenta il notevole problema dello smaltimento di grandi quantità di zinco cloruro e di DMF. La reazione studiata, condotta in catalisi eterogenea, in presenta di H2, presenta una forte dipendenza dalla natura dei metalli utilizzati oltre che dal tipo di sintesi dei catalizzatori impiegati. Nell'ambito di questo lavoro è stato sviluppato un metodo, a basso impatto ambientale, per la sintesi si nanoparticelle preformate da utilizzare per la preparazione di catalizzatori supportati si TiO2 e SiO2. Le nanosospensioni ed i sistemi catalitici prodotti sono stati caratterizzati utilizzando diverse metodologie di analisi quali: XRD, XRF, TEM, TPR-MS, che hanno permesso di ottimizzare le diverse fasi della preparazione. Allo scopo di osservare effetti sinergici tra le specie utilizzate sono stati confrontati sistemi catalitici monometallici con sistemi bimetallici, rivelando interessanti implicazioni derivanti dall’utilizzo di fasi attive nanoparticellari a base di Pd e Cu. In particolare, è stato possibile apprezzare miglioramenti significativi nelle prestazioni catalitiche in termini di selettività a perfluorometilviniletere all’aumentare del contenuto di Cu. La via di sintesi ottimizzata e impiegata per la produzione di nanoparticelle bimetalliche è risultata una valida alternativa, a basso impatto ambientale, ai metodi di sintesi normalmente usati, portando alla preparazione di catalizzatori maggiormente attivi di quelli preparati con i metalli standard.

In-situ-Präparation von komplexen supraleitenden und ferroelektrischen Heterostrukturen mittels gepulster Laser-Deposition

In der vorliegenden Arbeit ist die Konstruktion und der Aufbau eines Systems zur gepulsten Laserablation von dünnen Schichten beschrieben. Die hohe Flexibilität der Anlage wird ermöglicht durch einen sechsfach-Targethalter und eine Heizerkonstruktion, die einfachen Substrateinbau, hohe Temperaturhomogenität und einen zugänglichen Temperaturbereich von bis zu 1000°C erlaubt. Durch eine komplexe Laser-Optik, die eine homogene Energiedichte auf dem Target sicherstellt, wird eine optimale Filmqualität erreicht.Durch die Entwicklung einer zweistufigen Prozeßführung für Y-stabilisiertes ZrO2 wird eine Wachstumsbasis hoher kristalliner Qualität für funktionale Oxidschichten auf Silizium zur Verfügung gestellt. Es zeigt sich, daß die dielektrischen Eigenschaften der YSZ Schicht stark vom Sauerstoffgehalt, der Grenzflächenmorphologie sowie der Dicke der ersten Schicht abhängig sind. Basierend auf dieser Schicht wurde BaZrO3 als zusätzliche Pufferschicht für den Hochtemperatursupraleiter (HTSL) YBa2Cu3O7 ? untersucht. Unter Verwendung von SrTiO3 Substraten konnte die dielektrische Konstante von BaZrO3 zu ? ? 65 bestimmt sowie das Dispersionsverhalten mittels modifizierter Debye-Gleichungen erklärt werden. Vergleichende Messungen auf einkristallinen SrTiO3 Substraten zeigen eine erhöhte Übergangstemperatur von 90.2 K und eine wesentliche Verbesserung der Oberflächenrauhigkeit des HTSL von 2 nm (rms) durch die Verwendung von BaZrO3 Schichten hoher Qualität. Eine nur wenige Monolagen dicke zusätzliche BaZrO3 Pufferschicht auf YSZ-gepufferten Silizium Substraten verhindert die Ausbildung von ?9° rotierten YBCO Körnern, die üblicherweise bei der direkten Deposition auf YSZ beobachtet werden. Resistive Messungen mit Übergangstemperaturen oberhalb 89 K sind vergleichbar zu Ergebnissen, die für CeO2/YSZ Pufferschichtkombinationen erreicht werden. Durch kontinuierliche Gitteranpassung wurde eine neue Schichtabfolge YBCO/CeO2/YSZ/BaZrO3 für die Erzeugung bi-epitaxialer Korngrenzen-Josephson Kontake gefunden und deren Epitaxiebeziehungen geklärt. Eine in-situ deponierte Schichtabfolge zeigt mit einer Übergangstemperatur von 91.7 K und einer Übergangsbreite von 0.15 K supraleitende Eigenschaften vergleichbar zu den besten bisher auf diesem Gebiet erreichten Ergebnissen. Voruntersuchungen zur Realisierung eines Josephsonkontaktes mit dieser Schichtabfolge zeigen jedoch, daß die erreichten Eigenschaften für die technologische Anwendung nicht ausreichend sind.Die Verwendung einer YSZ/CeO2 Pufferschichtkombination ermöglicht die Herstellung von c Achsen orientiertem ferroelektrischem SrBi2Ta2O9 auf Silizium. Im Gegensatz hierzu führt die direkte Deposition auf Silizium zu polykristallinem SrBi2Ta2O9 oder zur Ausbildung der Pyrochlor Phase, wenn nur YSZ als Pufferschicht verwendet wird. Obwohl die Polarisierung von SrBi2Ta2O9 in der ab-Ebene liegt, konnte in MFIS Strukturen ein Speicherfenster von maximal 0.87 V beobachtet werden, was eine Verbesserung um nahezu einen Faktor drei im Vergleich zu polykristallinem SrBi2Ta2O9 bedeutet. Messungen an ferroelektrischen Kondesatorstrukturen ergeben Hystereseschleifen mit einer remanenten Polarisierung von Pr = 6.5 µC/cm2 sowie einem Koerzitivfeld von Ec = 35 kV/cm. AFM Messungen im Piezo-Response Modus zeigen ferroelektrische Domänen, die durch Anlegen einer Gleichspannung reversibel umpolarisiert werden können. Im Nicht-Kontakt AFM Modus wurde die lokale Polarisierung der Schichten zu 3.4 µC/cm2 bestimmt. Weiterhin wurde eine alternative Pufferschichtkombination SrZrO3/YSZ zur Erzeugung von a-Achsen orientiertem SrBi2Ta2O9 untersucht. SrZrO3 zeigt a Achsen Orientierung in vier Wachstumsdomänen, die durch ein Model erklärt werden können. Die SrBi2Ta2O9 Schicht zeigt a Achsen sowie (116)-orientierte Körner mit derselben Domänenstruktur. Die dielektrische Konstanten von SrZrO3 und SrBi2Ta2O9 wurden zu ? ? 29 und ? ? 20 bestimmt. Die beobachteten Speicherfenster sind allerdings nicht ferroelektrischer Natur, sondern wahrscheinlich durch mobile Ionen und Ladungsfangstellen in den Pufferschichten verursacht. Die stark abgesenkte dielektrische Konstante von SrBi2Ta2O9 kann durch die im Vergleich zu polykristallinem verkleinerte Korngröße erklärt werden.

Rastertunnelmikroskopie kombiniert mit optischen Methoden und ihre Anwendung für opto-elektronische Experimente an nanoskopischen Strukturen

Die vorliegende Arbeit untersucht mittels lichtunterstützter Tunnelmikroskopie (STM) den Elektronentransport in farbstoffbedeckten, nanoporösen TiO2-Schichten, die in photoelektrochemischen Solarzellen eingesetzt werden. Transportrelevante Eigenschaften wie die elektronische Zustandsdichte sowie lichtinduzierte Vorgänge wie der Aufbau einer lichtinduzierten Oberflächenladung und lokale Photoströme werden ortsaufgelöst gemessen. Für einen möglichen Einsatz in lichtunterstützter Tunnelmikroskopie werden desweiteren Gold-Nanopartikel auf einer Amino-Hexanthiol-Monolage auf Coulomb-Blockaden untersucht. Den zweite Schwerpunkt stellen methodische Arbeiten zur Messung optischer Nahfelder in STM-Experimenten dar. Erstens sollen die Vorteile von Apertur- und aperturloser optischer Rasternahfeld-Mikroskopie mit komplett metallisierten Faserspitzen verbunden werden, die durch die Faser beleuchtet werden. Es gelingt nicht, theoretisch vorhergesagte hohe optische Auflösungen zu bestätigen. Zweitens werden transparente Spitzen aus Sb-dotiertem Zinnoxid erfolgreich als Tunnelspitzen getestet. Die Spitzen ermöglichen STM-Elektrolumineszenz-Experimente zur Charakterisierung optischer Nahfelder, ohne diese durch eine metallische Spitze zu beeinträchtigen. In einer STM-Studie wird das Selbstorganisations-Verhalten von Oktanthiol und Oktandithiol auf Au(111) aus Ethanol untersucht. Bei geringer relativer Konzentration der Dithiole (1:2000), bildet sich eine Phase liegender Dithiole, deren Ordnung durch die Präsenz der Oktanthiole katalysiert wird. Schließlich wird ein als 'dynamische Tunnelmikroskopie' bezeichneter Modus für die Tunnelmikroskopie in elektrisch leitfähiger Umgebung erfolgreich getestet, der zur Unterdrückung des elektrochemischen Leckstromanteils die Ableitung des Stroms nach dem Abstand als STM-Abstandssignal verwendet.