956 resultados para VISIBLE LUMINESCENCE
Resumo:
Glucose sensing is an issue with great interest in medical and biological applications. One possible approach to glucose detection takes advantage of measuring changes in fluorescence resonance energy transfer (FRET) between a fluorescent donor and an acceptor within a protein which undergoes glucose-induced changes in conformation. This demands the detection of fluorescent signals in the visible spectrum. In this paper we analyzed the emission spectrum obtained from fluorescent labels attached to a protein which changes its conformation in the presence of glucose using a commercial spectrofluorometer. Different glucose nanosensors were used to measure the output spectra with fluorescent signals located at the cyan and yellow bands of the spectrum. A new device is presented based on multilayered a-SiC:H heterostructures to detect identical transient visible signals. The transducer consists of a p-i'(a-SiC:H)-n/p-i(a-Si:H)-n heterostructure optimized for the detection of the fluorescence resonance energy transfer between fluorophores with excitation in the violet (400 nm) and emissions in the cyan (470 nm) and yellow (588 nm) range of the spectrum. Results show that the device photocurrent signal measured under reverse bias and using appropriate steady state optical bias, allows the separate detection of the cyan and yellow fluorescence signals. (C) 2013 Elsevier B.V. All rights reserved.
Resumo:
Combined tunable WDM converters based on SiC multilayer photonic active filters are analyzed. The operation combines the properties of active long-pass and short-pass wavelength filter sections into a capacitive active band-pass filter. The sensor element is a multilayered heterostructure produced by PE-CVD. The configuration includes two stacked SiC p-i-n structures sandwiched between two transparent contacts. Transfer function characteristics are studied both theoretically and experimentally. Results show that optical bias activated photonic device combines the demultiplexing operation with the simultaneous photodetection and self amplification of an optical signal acting the device as an integrated photonic filter in the visible range. Depending on the wavelength of the external background and irradiation side, the device acts either as a short- or a long-pass band filter or as a band-stop filter. The output waveform presents a nonlinear amplitude-dependent response to the wavelengths of the input channels. A numerical simulation and a two building-blocks active circuit are presented and give insight into the physics of the device. (c) 2013 Elsevier B.V. All rights reserved.
Resumo:
The paper focuses on the importance of Darwin’s work for the shaping of Henri Bergson’s philosophy, bearing on mind that the two authors first intercepted symbolically in 1859, when On the Origin of Species was published and Bergson was born. Bergson studied the biological sciences of his time, whose results were integrated in a metaphysical thought. He belonged to spiritualistic positivism, a philosophy that goes from the positive data of sciences and finds the ultimate explanation of reality in a spiritual principle. He was interested in the positive evolution of the natural world and in the works of naturalists such as Lamarck, De Vries or Eimer. Darwin was among these authors, being responsible for a vision of evolution that went from the scientific level to other domains. Bergson defends the “insufficiency of pure Darwinism” by pointing out the necessity to compensate scientific evolution with an internal metaphysical reading of the real, which he considered to be “true evolutionism”. This criticism is the most visible aspect of the relations between both works. However, an attentive look verifies that Darwin’s influence overcomes the divergence of positions concerning the extent of “evolution”. The French philosopher knew not only the 1859’s bestseller, but also studies by Darwin about ethology, entomology and botany, which contributed to the fact that the naturalist’s impact gained fundamental importance in Bergson’s philosophical perspective.
Resumo:
ABSTRACT - Tinea pedis and onychomycosis are two rather diverse clinical manifestations of superficial fungal infections, and their etiologic agents may be dermatophytes, non-dermatophyte moulds or yeasts. This study was designed to statistically describe the data obtained as results of analysis conducted during a four year period on the frequency of Tinea pedis and onychomycosis and their etiologic agents. A questionnaire was distributed from 2006 to 2010 and answered by 186 patients, who were subjected to skin and/or nail sampling. Frequencies of the isolated fungal species were cross-linked with the data obtained with the questionnaire, seeking associations and predisposing factors. One hundred and sixty three fungal isolates were obtained, 24.2% of which composed by more than one fungal species. Most studies report the two pathologies as caused primarily by dermatophytes, followed by yeasts and lastly by non-dermatophytic moulds. Our study does not challenge this trend. We found a frequency of 15.6% of infections caused by dermatophytes (with a total of 42 isolates) of which T. rubrum was the most frequent species (41.4%). There was no significant association (p >0.05) among visible injury and the independent variables tested, namely age, gender, owning pet, education, swimming pools attendance, sports activity and clinical information. Unlike other studies, the variables considered did not show the expected influence on dermatomycosis of the lower limbs. It is hence necessary to conduct further studies to specifically identify which variables do in fact influence such infections.
Resumo:
This paper reports on the structural and optical properties of Co-doped TiO2 thin films grown onto (0001)Al2O3 substrates by non-reactive pulsed laser deposition (PLD) using argon as buffer gas. It is shown that by keeping constant the substrate temperature at as low as 310 degrees C and varying only the background gas pressure between 7 Pa and 70 Pa, it is possible to grow either epitaxial rutile or pure anatase thin films, as well as films with a mixture of both polymorphs. The optical band gaps of the films are red shifted in comparison with the values usually reported for undoped TiO2, which is consistent with n-type doping of the TiO2 matrix. Such band gap red shift brings the absorption edge of the Co-doped TiO2 films into the visible region, which might favour their photocatalytic activity. Furthermore, the band gap red shift depends on the films' phase composition, increasing with the increase of the Urbach energy for increasing rutile content. (C) 2012 Elsevier B.V. All rights reserved.
Resumo:
There is an imminent need for rapid methods to detect and determine pathogenic bacteria in food products as alternatives to the laborious and time-consuming culture procedures. In this work, an electrochemical immunoassay using iron/gold core/shell nanoparticles (Fe@Au) conjugated with anti-Salmonella antibodies was developed. The chemical synthesis and functionalization of magnetic and gold-coated magnetic nanoparticles is reported. Fe@Au nanoparticles were functionalized with different self-assembled monolayers and characterized using ultraviolet-visible spectrometry, transmission electron microscopy, and voltammetric techniques. The determination of Salmonella typhimurium, on screen-printed carbon electrodes, was performed by square-wave anodic stripping voltammetry through the use of CdS nanocrystals. The calibration curve was established between 1×101 and 1×106 cells/mL and the limit of detection was 13 cells/mL. The developed method showed that it is possible to determine the bacteria in milk at low concentrations and is suitable for the rapid (less than 1 h) and sensitive detection of S. typhimurium in real samples. Therefore, the developed methodology could contribute to the improvement of the quality control of food samples.
Resumo:
In this paper we present results on the use of a semiconductor heterostructure based on a-SiC:H as a wavelength-division demultiplexer for the visible light spectrum. The proposed device is composed of two stacked p-i-n photodiodes with intrinsic absorber regions adjusted to short and long wavelength absorption and carrier collection. An optoelectronic characterisation of the device was performed in the visible spectrum. Demonstration of the device functionality for WDM applications was done with three different input channels covering the long, the medium and the short wavelengths in the visible range. The recovery of the input channels is explained using the photocurrent spectral dependence on the applied voltage. An electrical model of the WDM device is proposed and supported by the solution of the respective circuit equations. Short range optical communications constitute the major application field however other applications are foreseen. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Resumo:
Dissertação de Mestrado, Gestão e Conservação da Natureza, 12 de Junho de 2014, Universidade dos Açores.
Resumo:
Mestrado em Engenharia Electrotécnica e de Computadores
Resumo:
In this paper we present results on the use of a multilayered a-SiC:H heterostructure as a wavelength-division demultiplexing device (WDM) for the visible light spectrum. The WDM device is a glass/ITO/a-SiC:H (p-i-n)/ a-SiC:H(-p) /Si:H(-i)/SiC:H (-n)/ITO heterostructure in which the generated photocurrent at different values of the applied bias can be assigned to the different optical signals. The device was characterized through spectral response measurements, under different electrical bias. Demonstration of the device functionality for WDM applications was done with three different input channels covering wavelengths within the visible range. The recovery of the input channels is explained using the photocurrent spectral dependence on the applied voltage. The influence of the optical power density was also analysed. An electrical model, supported by a numerical simulation explains the device operation. Short range optical communications constitute the major application field, however other applications are also foreseen.
Resumo:
Mestrado (PES II), Educação Pré-Escolar e Ensino do 1º Ciclo do Ensino Básico, 3 de Julho de 2014, Universidade dos Açores.
Resumo:
O Acidente Vascular Encefálico é uma das principais causas de morte, tornando-se cada vez mais iminente processos de reabilitação que minimizem as sequelas, nomeadamente as limitações do membro superior que dificultam o envolvimento em atividades da vida diária. O Constraint-Induced Movement Therapy, surge como uma abordagem que incrementa o uso do membro superior mais afetado. A presente investigação trata-se de um estudo de casos múltiplos. Pretende-se verificar se existem melhorias na funcionalidade do membro superior mais afetado, analisar em que atividades da vida diária são visíveis melhorias funcionais e compreender se o maior envolvimento nas atividades diárias está diretamente relacionado com a melhoria na capacidade funcional. Pretende-se ainda que os valores obtidos no Wolf Motor Function Test sejam um contributo para a sua validação para a população portuguesa. Utilizou-se um questionário para recolha de dados pessoais e clínicos (amplitudes de movimento, dor e espasticidade); o Wolf Motor Function Test e o Action Research Arm Test para verificar a funcionalidade do membro superior mais afetado; e a Motor Activity Log que avalia o envolvimento em atividades da vida diária. O grupo é constituído por 3 utentes que sofreram um primeiro Acidente Vascular Encefálico até 9 meses de evolução, internados na Santa Casa da Misericórdia de Monção e que cumpriam os critérios de inclusão. O programa foi implementado três horas/dia, durante 10 dias, mantendo a restrição no membro superior menos afetado durante 90% do dia acordado. Como se trata de um estudo de casos múltiplos, analisou-se cada participante individualmente e verificou-se a diferença entre os resultados finais e iniciais para cada uma das variáveis. Os resultados obtidos revelam ganhos na amplitude de movimento, velocidade de execução e capacidade funcional do membro superior mais afetado, nomeadamente nas funções de preensão e pinça da mão, bem como se testemunhou minimização do fenómeno learned nonuse. Verificaram-se ganhos funcionais em todos os participantes nas atividades da vida diária apesar de serem diferentes de participante para participante. Dois participantes afirmaram que voltariam a participar no programa.Conclui-se, assim que a técnica resulta em ganhos funcionais nestes utentes, indicando um caminho alternativo a outras abordagens de reabilitação.
Resumo:
A Sequência de Movimento de Sentado para de Pé (SMSP) é um marco importante na independência funcional da criança, sendo a sua qualidade afetada em casos de alteração do controlo postural do tronco. É por isso motivo de especial foco neste estudo, como elemento avaliativo e interventivo. Este estudo tem como objetivo a análise da modificação de componentes motores relacionados com o controlo postural, durante a SMSP, em 5 crianças com alterações neuromotoras, face à aplicação de um programa de intervenção baseado no Tratamento de Neuro Desenvolvimento (TND). Foi para tal utilizada a análise cinemática da SMSP - nomeadamente as variáveis “variação do deslocamento dos segmentos cabeça e tronco” e “variação do ângulo perna-pé” entre o momento inicial e o seat-off – complementada com a aplicação do Teste de Medida da Função Motora 88 (TMFM-88) e a Classificação Internacional da Funcionalidade Incapacidade e Saúde-Versão Crianças e Jovens (CIF-CJ), bem como a avaliação de componentes de movimento com recurso a registo de imagem. A análise cinemática demonstrou uma diminuição do deslocamento dos segmentos cabeça e tronco na maioria dos casos, bem como uma maior mobilidade da tíbia sobre pé. Verificou-se um aumento do score final do TMFM-88, em todos os casos. A CIF-CJ não evidenciou alterações entre o início e o término do período de intervenção. O registo de imagem demonstrou alterações positivas visíveis no alinhamento de segmentos, nível de atividade, controlo postural, e recurso a estratégias compensatórias no conjunto postural sentado e na SMSP. Após o período de intervenção as crianças deste estudo evidenciaram modificações positivas nas variáveis em estudo, nomeadamente 1) diminuição do deslocamento dos segmentos cabeça e tronco na fase inicial da SMSP, 2) aumento da variação do ângulo perna-pé na fase inicial da SMSP, 3) aumento do score total da TMFM-88, 4) alteração positiva dos componentes de movimento alinhamento de segmentos e nível de atividade e 5) redução do recurso a estratégias compensatórias de movimento na SMSP. Estas modificações sugerem um controlo postural mais eficiente.
Resumo:
Nas últimas décadas, devido ao desenvolvimento económico, e a uma necessidade constante de gerir os recursos energéticos, existe uma necessidade de procurar novas fontes de energia, em particular fontes de energia renováveis. O biodiesel surge assim como uma energia alternativa ao combustível fóssil. Este biocombustível tem ganho uma importância significativa na sociedade moderna. Quimicamente o biodiesel é constituído por ésteres metílicos de ácidos gordos de cadeia longa, derivados de óleos vegetais ou gorduras animais. O principal problema que este enfrenta é a sua susceptibilidade à oxidação, devido ao seu conteúdo de ácidos gordos insaturados, logo existe uma procura constante de soluções que possam solucionar este problema. É necessária a identificação de técnicas e métodos para retardar a seu envelhecimento ao longo do tempo. O objectivo deste trabalho consiste no estudo da estabilidade do biodiesel ao longo do tempo, quando armazenado a diferentes condições de temperatura, superiores às normalmente suportadas pelo biodiesel durante o armazenamento, de modo a acelerar o processo de degradação. As amostras de biodiesel foram sujeitas a duas temperaturas. Uma amostra de biodiesel não estabilizado foi colocada a uma temperatura entre 40 e 50ºC ao longo de 203 dias, e uma outra amostra foi colocada a uma temperatura entre 95º e 105ºC ao longo de 146 dias. Realizaram-se ensaios semanais de modo registar a evolução do envelhecimento do biodiesel. As análises foram efectuadas por espectrofotometria de ultravioleta e visível (UV-VIS) e por espectroscopia de absorção na região do infravermelho (FTIR). No UV-VIS foi possível observar que o aumento de temperatura foi responsável pela aceleração da oxidação do biodiesel que resulta num aumento generalizado da absorvância do biodiesel. Através das análises efectuadas no FTIR verificou-se a formação e aumento da banda dos hidroperóxidos (grupo ROOH) localizada entre 3000 e 3600 cm-1 nos espectros, e igualmente um alargamento na banda dos carbonilos (grupo C=O) entre 1500 e 1900 cm-1. Numa fase posterior testaram-se antioxidantes para retardar o envelhecimento do biodiesel. Os ensaios foram efectuados a uma temperatura entre 95º e 105ºC. Os antioxidantes utilizados foram o galhato de propilo (PG), o galhato de etilo (EG) e o ácido gálhico (AG). Recorreu-se a técnicas como o UV-VIS e o FTIR para o registo dos espectros do biodiesel ao longo do tempo. Através destas técnicas foi possível verificar a influência de antioxidantes na estabilidade oxidativa do biodiesel. O PG foi o antioxidante que melhor desempenho mostrou no retardamento da oxidação do biodiesel e a técnica que melhor permitiu analisar a acção dos antioxidantes foi o UVVIS. Os resultados obtidos por FTIR não se mostraram tão conclusivos. Para caracterizar o envelhecimento do biodiesel não estabilizado e estabilizado utilizou-se também a cromatografia gasosa (CG) para quantificar a percentagem de ésteres metílicos presentes nas diferentes amostras no inicio e no fim do processo de oxidação. O biodiesel envelheceu mais rapidamente para temperaturas mais elevadas e comprovou-se que o antioxidante que melhor estabiliza o biodiesel é o PG.
Resumo:
Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Electrónica e Telecomunicações