On the activation and physical degradation of boron-doped diamond surfaces brought on by cathodic pretreatments

The electrochemical activation and physical degradation of boron-doped diamond (BDD) electrodes with different boron doping levels after repeated cathodic pretreatments are reported. Galvanostatic cathodic pretreatment passing up to -14000 C cm(-2) in steps of -600 C cm(-2) using -1 A cm(-2) caused significant physical degradation of the BDD surface, with film detachment in some areas. Because of this degradation, a great increase in the electrochemically active area was observed in Tafel plots for the hydrogen evolution reaction (HER) in acid media. The minimum cathodic pretreatment needed for the electrochemical activation of the BDD electrodes without producing any observable physical degradation on the BDD surfaces was determined using electrochemical impedance spectroscopy (EIS) measurements and cyclic voltammetry: -9 C cm(-2), passed at -1 A cm(-2). This optimized cathodic pretreatment can be safely used when electrochemical experiments are carried out on BDD electrodes with doping levels in the range between 800 and 8000 ppm.

A quantum chemical study on a set of non-imidazole H(3) antihistamine molecules

Molecular orbital calculations were carried out on a set of 28 non-imidazole H(3) antihistamine compounds using the Hartree-Fock method in order to investigate the possible relationships between electronic structural properties and binding affinity for H3 receptors (pK(i)). It was observed that the frontier effective-for-reaction molecular orbital (FERMO) energies were better correlated with pK(i) values than highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy values. Exploratory data analysis through hierarchical cluster (HCA) and principal component analysis (PCA) showed a separation of the compounds in two sets, one grouping the molecules with high pK(i) values, the other gathering low pK(i) value compounds. This separation was obtained with the use of the following descriptors: FERMO energies (epsilon(FERMO)), charges derived from the electrostatic potential on the nitrogen atom (N(1)), electronic density indexes for FERMO on the N(1) atom (Sigma((FERMO))c(i)(2)). and electrophilicity (omega`). These electronic descriptors were used to construct a quantitative structure-activity relationship (QSAR) model through the partial least-squares (PLS) method with three principal components. This model generated Q(2) = 0.88 and R(2) = 0.927 values obtained from a training set and external validation of 23 and 5 molecules, respectively. After the analysis of the PLS regression equation and the values for the selected electronic descriptors, it is suggested that high values of FERMO energies and of Sigma((FERMO))c(i)(2), together with low values of electrophilicity and pronounced negative charges on N(1) appear as desirable properties for the conception of new molecules which might have high binding affinity. 2010 Elsevier Inc. All rights reserved.

The influence of perhydroazepine and piperidine as further ancillary ligands on Ru-PPh(3)-based catalysts for ROMP of norbornene and norbornadiene

Polynorbornadiene and polynorbornene were synthesized via ring opening metathesis polymerization (ROMP) with [RuCl(2)(PPh(3))(2)(amine)] as catalyst precursors, amine = piperidine (1) or perhydroazepine (2) in the presence of 5 mu L of ethyl diazoacetate (EDA) ([monomer]/[Ru] = 5000; 40 degrees C with 1; 25 degrees C with 2). The effects of the solvent volume (2-8 mL of CHCl(3)) reaction time (5-120 min) and atmosphere type (argon and air) on the yields were investigated to observe the behavior of the two different precursors. Quantitative yields were obtained for 60 or 120 min regardless of the starting volumes, either in argon or air, with both Ru species. However, low yields were obtained for short times (5-30 min) when the reactions are performed with large volumes (6-8 mL). In argon, the yields were larger with 2, associated to a faster propagation reaction controlled by the Ru active species. In air, the yields were larger with 1, associated to a higher resistance to O(2) of the starting and propagating Ru species. The different activities between 1 and 2 are discussed considering the steric hindrance and electronic characteristics of the amines such as ancillary ligands and their arrangements with PPh(3) and Cl(-) ions in the metal centers. (c) 2009 Elsevier B.V. All rights reserved.

Utilização do grão tostado de soja (Glicine max (L) Merril) na alimentação de vacas em lactação

Soybeans were roasted in an experimental roaster during 2 or 3 minutes either at 380 or 490 ºC air temperature and kept or not for 30 minutes under steeping. The heat treatment effects on soybeans were evaluated in a first trial through two different procedures: a) after 16 hours of an “in situ” ruminal incubation period, all heat treated soybeans showed an increased (P<0,05) rumen undegraded protein (RUP) content in comparison to raw soybeans; b) a pepsin/pancreatin “in vitro” procedure showed that roasting at 380 ºC, during 2 minutes, with steeping, or at 380 ºC , during 3 minutes without steeping, did not affect the “in vitro” enzymatic intestinal digestibility of soybeans (P>0,05). In a second trial, soybeans roasted at 380 ºC, during 2 minutes and kept under steeping were included in isonitrogenous and isocaloric lactating dairy cows rations and evaluated in comparison to raw soybeans, with two other protein sources as references. There were no differences (P>0,05) between the roasted and raw soybeans diets related either to dry matter or crude protein intakes, milk yield and composition and plasma urea nitrogen (PUN) and milk urea nitrogen (MUN) concentrations, but roasted soybeans yielded significantly (P<0,05) more milk per kg of dry matter or crude protein intake than raw soybeans.

Caracterização de núcleos celulares no adenocarcinoma primário de reto por análise de imagem digital

O câncer colorretal é um tumor maligno freqüente no mundo ocidental. É o terceiro em freqüência e o segundo em mortalidade nos países desenvolvidos. No Brasil está entre as seis neoplasias malignas mais encontradas e a quinta em mortalidade. Dos tumores colorretais, aproximadamente 40% estão localizados no reto. A sobrevida, em cinco anos, dos pacientes operados por câncer do reto varia entre 40% e 50%, estando os principais fatores prognósticos, utilizados na prática clínica corrente, baseados em critérios de avaliação clínico-patológicos. A avaliação das alterações morfométricas e densimétricas nas neoplasias malignas tem, recentemente, sido estudadas e avaliadas através da análise de imagem digital e demonstrado possibilidades de utilização diagnóstica e prognóstica. A assinatura digital é um histograma representativo de conjuntos de características de textura da cromatina do núcleo celular obtida através da imagem computadorizada. O objetivo deste estudo foi a caracterização dos núcleos celulares neoplásicos no adenocarcinoma primário de reto pelo método da assinatura digital e verificar o valor prognóstico das alterações nucleares da textura da cromatina nuclear para esta doença. Foram avaliados, pelo método de análise de imagem digital, 51 casos de pacientes operados no Hospital de Clínicas de Porto Alegre (HCPA) entre 1988 e 1996 e submetidos à ressecção eletiva do adenocarcinoma primário de reto, com seguimento de cinco anos pós-operatório, ou até o óbito antes deste período determinado pela doença, e 22 casos de biópsias normais de reto obtidas de pacientes submetidos a procedimentos endoscópicos, para controle do método da assinatura digital. A partir dos blocos de parafina dos espécimes estocados no Serviço de Patologia do HCPA, foram realizadas lâminas coradas com hematoxilina e eosina das quais foram selecionados 3.635 núcleos dos adenocarcinomas de reto e 2.366 núcleos dos controles da assinatura digital, totalizando 6.001 núcleos estudados por análise de imagem digital. De cada um destes núcleos foram verificadas 93 características, sendo identificadas 11 características cariométricas com maior poder de discriminação entre as células normais e neoplásicas. Desta forma, através da verificação da textura da cromatina nuclear, foram obtidos os histogramas representativos de cada núcleo ou conjunto de núcleos dos grupos ou subgrupos estudados, também no estadiamento modificado de Dukes, dando origem às assinaturas digitais correspondentes. Foram verificadas as assinaturas nucleares, assinaturas de padrão histológico ou de lesões e a distribuição da Densidade Óptica Total. Houve diferença significativa das características entre o grupo normal e o grupo com câncer, com maior significância para três delas, a Área, a Densidade Óptica Total e a Granularidade nuclear. Os valores das assinaturas médias nucleares foram: no grupo normal 0,0009 e nos estadiamentos; 0,9681 no A, 4,6185 no B, 2,3957 no C e 2,1025 no D e diferiram com significância estatística (P=0,001). A maior diferença do normal ocorreu no subgrupo B de Dukes-Turnbull. As assinaturas nucleares e de padrão histológico mostraram-se distintas no grupo normal e adenocarcinoma, assim como a distribuição da Densidade Óptica Total a qual mostra um afastamento progressivo da normalidade no grupo com câncer. Foi possível a caracterização do adenocarcinoma de reto, que apresentou assinaturas digitais específicas. Em relação ao prognóstico, a Densidade Óptica Total representou a variável que obteve o melhor desempenho, além do estadiamento, como preditor do desfecho.

Desenvolvimento de um aço SAE 5115 microligado ao nióbio para cementação a alta temperatura

Este trabalho busca desenvolver um aço para cementação a alta temperatura através da adição de nióbio como microligante, a fim de que os compostos formados forneçam partículas de segunda fase que atuem como ancoradoras do grão austenítico, já que o processo de crescimento de grão, especialmente anormal, é conseqüência natural das temperaturas envolvidas. A elevação da temperatura tem como objetivo proporcionar um ganho em produtividade pela redução dos tempos de cementação. Procura-se também estabelecer uma comparação do aço proposto a aços de cementação convencionais (DIN 17Cr3 e SAE 5115). Utilizou-se um aço SAE 5115 com 0,034% de nióbio, que foi submetido a diferentes condições de ensaio em laboratório: deformação a frio por compressão livre em três graus de deformação (isento, 25 e 50%); com posterior aquecimento em patamares de temperatura que simulam diferentes níveis de cementação (930 , 950 , 1000 e 1050 C), bem como diferentes tempos de manutenção em temperatura, de tal forma a atingir camadas cementadas hipotéticas em torno de 1,0 mm de profundidade. Encerram-se os testes submetendo o aço estudado a um processo de produção industrial de pinos de pistão, que sofrem deformação a temperatura ambiente e cementação a 950 C por 2,5 h O aço SAE 5115 ao “Nb” mostrou um melhor desempenho no controle dos grãos austeníticos, tanto para os ensaios de simulação realizados em laboratório e comparados ao aço DIN 17Cr3, como frente ao processo de produção de pinos de pistão tendo como comparativo o aço SAE 5115. O modelo teórico de Hudd e outros (que trata os carbonitretos de nióbio como de extensiva solubilidade mútua) e o de Gladman (que define os nitretos de alumínio e de nióbio como mutuamente exclusivos), associados às equações de Wagner (para coalescimento das partículas de segunda fase), bem como à equação de Gladman e Pickering (que determina o raio crítico de partícula para uma distribuição aleatória de partículas), mostraram-se bastante adequados em prever a resposta das partículas precipitadas, partindo-se da composição química do aço, principalmente para as partículas de carbonitreto de nióbio em condições que não envolvessem níveis elevados de deformação.

Formação de biofilmes em diferentes materiais utilizados na indústria de processamento de leite

Biofilmes bacterianos na indústria de alimentos freqüentemente são prejudiciais, uma vez que podem abrigar patógenos e deteriorantes que contaminam os produtos. Este trabalho se propôs a avaliar e correlacionar o papel dos fatores de adesão e da hidrofobicidade na formação de biofilmes em diversos materiais. Leite in natura foi aliquotado em tubos contendo corpos de prova constituídos de vidro, polipropileno, aço inoxidável e pano de algodão e incubados em 10 °C e 25 °C. Após 2 h, 5 h e 8 h de contato, as células não aderidas foram removidas da superfície dos materiais, e as aderidas contadas em PCA. Foram isolados e identificados microrganismos dos biofilmes, sendo verificada a produção de cápsula (coloração com vermelho congo), fímbria (hemaglutinação em placa), hemolisinas (ágar sangue) e proteases (ágar leite). As hidrofobicidades celular e dos materiais foram determinadas pelos testes de agregação com sulfato de amônio e do ângulo do raio da gota séssil, respectivamente. Verificou-se a adesão de consórcios formados por E. coli, S. aureus e B. cereus. Os 103 isolados obtidos pertencem, principalmente, a espécies da família Enterobacteriaceae (46) e do gênero Staphylococcus (45). Na produção de fatores de virulência, 50,4% dos isolados produziram cápsula, 48,5% produziram fímbria, 55,3% hemolisina e 20,3% proteases. Dos microrganismos Gram-positivos e Gram-negativos, 86,6% e 84,4% foram positivos para o teste de hidrofobicidade, respectivamente. O aço inoxidável foi o material mais hidrofóbico testado, seguido por polipropileno e vidro. A temperatura de 25 °C e o polipropileno foram os maiores favorecedores de adesão dos consórcios bacterianos.

Effect of cooling rate on properties of plasma nitrided AISI 1010 steel

In this work, AISI 1010 steel samples were plasma nitrided into 20% N 2 100 Pa and 400 Pa for N 2 and H 2 , respectively), temperatures of 500 and 580 °C, during 2 h. Three different procedures for cooling were accomplished after nitriding. In the first procedure the cooling occurred naturally, that is, the sample was kept on substrate holder. In the second one the sample was pulled off and cooling in a cold surface. Finally, in the third cooling process the sample was pulled off the substrate holder down into special reservoir filled with oil held at ambient temperature. The properties of the AISI 1010 steel samples were characterized by optical and electron microscopy, X-ray diffraction, Mössbauer spectroscopy and microhardness tests. Thermal gradient inside the sample kept on substrate holder during cooling process was measured by three inserted thermocouples at different depths. When samples were cooled rapidly the transformation of ϵ-Fe 2 − 3 N to γ′-Fe 4 N was inhibited. Such effect is indicated by the high concentration of ϵ-Fe compound zone. To get solid state solution of nitrogen in the diffusion zone, instead of precipitates of nitride phases, the cooling rate should be higher than a critical value of about 0.95 °C/s. When this value is reached at any depth of the diffusion zone, two distinct diffusion zones will appear. Temperature gradients were measured inside the samples as a consequence of the plasma treatment. It's suggested the need for standardization of the term “treatment temperature” for plasma treatment because different nitrided layer properties could be reported for the same “treatment temperature”.

Avaliação do efeito citotóxico da lectina da esponja marinha Cliona varians contra células de leucemia mielóide crônica

In this study, a BCR-ABL expressing human chronic myelogenous leukaemia cell line (K562) was used to investigate the antitumoral potential of a novel lectin (CvL) purified from the marine sponge Cliona varians. CvL inhibited the growth of K562 cells with an IC50 value of 70 g/ml, but was ineffective to normal human peripheral blood lymphocytes in the same range of concentrations tested (180 g/ml). Cell death occurred after 72 h of exposure to the lectin and with sign of apoptosis as analysed by DAPI staining. Investigation of the possible effectors of this process showed that cell death occurred in the presence of Bcl-2 and Bax expression, and involved a caspase-independent pathway. Confocal fluorescence microscopy indicated a major role for the lysosomal protease cathepsin B in mediating cell death. Accordingly, pre-incubation of K562 cells with the cathepsin inhibitor L-trans-epoxysuccinyl-L-leucylamido-(4-guanidino)butane (E-64) abolished the cytotoxic effect of CvL. Furthermore, we found upregulation of tumor necrosis factor receptor 1 (TNFR1) and down-modulation of p65 subunit of nuclear factor kappa B (NFB) expression in CvL-treated cells. These effects were accompanied by increased levels of p21 and downmodulation of pRb, suggesting that CvL is capable of cell cycle arrest. Collectively, these findings suggest that cathepsin B acts as death mediator in CvL-induced cytotoxicity possibly in a still uncharacterized connection with the membrane death receptor pathway

Síntese e caracterização de óxidos de cério e cobalto obtidos por gel-combustão e Pechini aplicados às reações de oxidação de n-hexano

Oxide type spinel AB2O4 presents structure adjusted for application in the automobile industry. The spinel of cobalt has many practical applications had its excellent physical and chemical properties such as catalyst in hydrocarbon oxidation reaction. The CeO2 has been used in many of these processes because it assigns to a material with excellent thermal resistance and mechanics, high capacity of oxygen stockage (OSC) among others properties. This work deals with the synthesis, characterization and catalytic application of spinel of cobalt and CeO2 with fluorita structure, obtained for method of Pechini and method of Gel-Combustion. The process of Pechini, the puff was obtained at 300 ºC for 2 h in air. In the process of Gel-Combustion the approximately at 350 ºC material was prepared and burnt for Pyrolysis, both had been calcined at 500 ºC, 700 ºC, 900 ºC and 1050 ºC for 2 h in air. The materials of the calcinations had been characterized by TG/DTA, electronic microscopy of sweepings (MEV), spectroscopy of absorption in the infra-red ray (FTIR) and diffraction of X-rays (DRX). The obtained material reaches the phase oxide at 450 oC for Pechini method and 500 °C for combustion method. The samples were submitted catalytic reaction of n-hexane on superficies of materials. The reactor function in molar ration of 0, 85 mol.h-1.g-1 and temperature of system was 450 °C. The sample obtained for Pechini and support in alumine of superficial area of 178,63 m2.g-1 calcined at 700 ºC, give results of catalytic conversions of 39 % and the sample obtained for method of gel-combustion and support in alumina of 150 mesh calcined at 500 ºC result 13 % of conversion. Both method were selective specie C1

Síntese e impregnação de peneiras moleculares Fe MCM-41 derivada de sílica da casca do arroz

The mesoporous molecular sieves of the MCM-41 and FeMCM-41 type are considered promissory as support for metals used as catalysts in oil-based materials refine processes and as adsorbents for environmental protection proposes. In this work MCM-41 and FeMCM41 were synthesized using rice husk ash - RHA as alternative to the conventional silica source. Hydrothermal synthesis was the method chosen to prepare the materials. Pre-defined synthesis parameters were 100°C for 168 hours, later the precursor was calcinated at 550°C for 2 hours under nitrogen and air flow. The sieves containing different proportions of iron were produced by two routes: introduction of iron salt direct synthesis; and a modification post synthesis consisting in iron salt 1 % and 5% impregnation in the material followed by thermal decomposition. The molecular sieves were characterized by X ray diffraction XRD, Fourier transform infrared spectroscopy FT-IR, X ray fluorescence spectroscopy XFR, scanning electronic microscopy SEM, specific surface area using the BET method, Termogravimetry TG. The kinetic model of Flynn Wall was used with the aim of determining the apparent activation energy of the surfactant remove (CTMABr) in the MCM- 41 porous. The analysis made possible the morphology characterization, identifying the presence of hexagonal structure typical for mesoporous materials, as well as observation of the MCM41 and iron of characteristic bands.

Síntese e caracterização de peneiras moleculares mesoporosas do tipo MCM-41 e AlMCM-41 a partir de fontes alternativas de sílica e de alumínio

The mesoporous molecular sieves of MCM-41 and AlMCM-41 type are considered as promising support for metal in the refining processes of petroleum-based materials as catalysts and adsorbents for environmental protection. In this work the molecular sieves MCM-41 and AlMCM-41 were synthesized by replacing the source of silica conventionally used, for quartz, an alternative and abundant, and the use of waste from the production of diatomaceous earth, an aluminum-silicate, as a source aluminum, due to abundant reserves of diatomaceous earth in the state of Rio Grande do Norte in the city of Ceará-Mirim, with the objective of producing high-value materials that have similar characteristics to traditional commercial catalysts in the market. These materials were synthesized by the method of hydrothermal synthesis at 100 º C for 7 days and subjected to calcination at 500 º C for 2 hours under flow of nitrogen and air. The molecular sieves were characterized by X-ray diffraction (XRD), differential thermal analysis (DTA) and thermogravimetric analysis (TG), adsorption of N2 (BET and BJH methods), spectroscopy in the infra red (FTIR), microscopy scanning electron (SEM) and transmission electron microscopy (TEM). The analysis indicated that the synthesized materials showed characteristic hexagonal structure of mesopores materials with high specific surface area and sort and narrow distribution of size of pores

Degradação do PMMA através da reação despolimerização uitlizando catalisadores de óxidos mistos

In this work, mixed oxides were synthesized by two methods: polymeric precursor and gel-combustion. The oxides, Niquelate of Lanthanum, Cobaltate of Lanthanum and Cuprate of Lanthanum were synthesized by the polymeric precursor method, and treated at 300 º C for 2 hours, calcined at 800 º C for 6h in air atmosphere. In gel-combustion method were produced and oxides using urea and citric acid as fuel, forming for each fuel the following oxides Ferrate of Lanthanum, Cobaltato of Lanthanum and Ferrato of Cobalt and Lanthanum, which were submitted to the combustion process assisted by microwave power maximum of 10min. The samples were characterized by: thermogravimetric analysis, X-ray diffraction; fisisorção of N2 (BET method) and scanning electron microscopy. The reactions catalytic of depolymerization of poly (methyl methacrylate), were performed in a reactor of silica, with catalytic and heating system equipped with a data acquisition system and the gas chromatograph. For the catalysts synthesized using the polymeric precursor method, the cuprate of lanthanum was best for the depolymerization of the recycled polymer, obtaining 100% conversion in less time 554 (min), and the pure polymer, was the Niquelate of Lanthanum, with 100% conversion in less time 314 (min). By gel-combustion method using urea as fuel which was the best result obtained Ferrate of Lanthanum for the pure polymer with 100% conversion in less time 657 (min), and the recycled polymer was Cobaltate of Lanthanum with 100 % conversion in less time 779 (min). And using citric acid to obtain the best result for the pure polymer, was Ferrate of Lanthanum with 100% conversion in less time 821 (min and) for the recycled polymer, was Ferrate of Lanthanum with 98.28% conversion in less time 635 (min)

Micropartículas de poli (ácido lático-co-ácido glicólico) obtidas por spray drying para a liberação prolongada de metotrexato

Methotrexate (MTX) is a drug used in the chemotherapy of some kind of cancers, autoimmune diseases and non inflammatory resistant to corticosteroids uveits. However, the rapid plasmatic elimination limits its therapeutic success, which leads to administration of high doses to maintain the therapeutic levels in the target tissues, occurring potential side effects. The aim of this study was to obtain spray dried biodegradable poly-lactic acid co-glycolic acid (PLGA) microparticles containing MTX. Thus, suitable amounts of MTX and PLGA were dissolved in appropriate solvent system to obtain solutions at different ratios drug/polymer (10, 20, 30 and 50% m/m). The physicochemical characterizing included the quantitative analysis of the drug using a validate UV-VIS spectrophotometry method, scanning electron microscopy (SEM), infrared spectrophotometry (IR), thermal analyses and X-ray diffraction analysis. The in vitro release studies were carried out in a thermostatized phosphate buffer pH 7.4 (0.05 M KH2PO4) medium at 37°C ± 0.2 °C. The in vitro release date was subjected to different kinetics release models. The MTX-loaded PLGA microparticles showed a spherical shape with smooth surface and high level of entrapped drug. The encapsulation efficiency was greater then 80%. IR spectroscopy showed that there was no chemical bond between the compounds, suggesting just the possible occurrence of hydrogen bound interactions. The thermal analyses and X-ray diffraction analysis shown that MTX is homogeneously dispersed inside polymeric matrix, with a prevalent amorphous state or in a stable molecular dispersion. The in vitro release studies confirmed the sustained release for distinct MTX-loaded PLGA microparticles. The involved drug release mechanism was non Fickian diffusion, which was confirmed by Kornmeyer-Peppas kinetic model. The experimental results demonstrated that the MTX-loaded PLGA microparticles were successfully obtained by spray drying and its potential as prolonged drug release system.

Uniformidade de deposição da calda de pulverização de herbicidas em barra lateral protegida com diferentes combinações de pontas de pulverização

O presente trabalho objetivou estudar a uniformidade de distribuição da calda de pulverização contendo herbicidas, em culturas perenes arbustivas, utilizando combinações de pontas de pulverização em barra lateral protegida, conduzida a pequena distância do alvo, na linha de culturas perenes arbustivas. Para isso, foi desenvolvido um programa computacional que permite simular a sobreposição do leque de pulverização, da porção protegida da barra e do leque formado pela ponta de pulverização do bico mais extremo da barra, de modo diferente dos demais programas. Após a seleção das melhores combinações de pontas de pulverização por meio de simulação dos padrões de deposição da pulverização das pontas individuais e dos coeficientes de variação menores que 10%, algumas dessas combinações foram testadas em campo, aplicando-se um herbicida sistêmico (glyphosate) e outro com ação de contato (paraquat). Os resultados indicaram que o programa computacional desenvolvido pode constituir-se em um auxiliar valioso para a seleção das melhores combinações de pontas de pulverização. em aplicações tanto do herbicida glyphosate quanto do paraquat, com volumes de calda mais reduzidos,abaixo de 100 L ha-1, destacaram-se como arranjos mais eficientes: a) pontas TT110015 distanciadas de 52,5 cm entre si, combinadas com a ponta TK-0,5 na extremidade da barra a 50 cm do último bico, operando na velocidade de 5 km h-1 e pressão de 103 kPa (15 lbf pol-2), com distância de caminhamento do tronco da árvore de 20 cm ; b) pontas SMCE2 distanciadas de 15 cm entre si, combinadas com a ponta TK-0,5 na extremidade da barra de 20 cm do último bico, operando na velocidade de 4 km h-1 e pressão de 414 kPa (60 lbf pol-2), com distância de caminhamento do tronco da árvore de 30 cm ; e c) pontas TLX-2 distanciadas de 15 cm entre si, combinadas com a ponta TK-0,5 na extremidade da barra de 20 cm do último bico, operando à velocidade de 5 km h-1 e pressão de 414 kPa (60 lbf pol-2), com distância de caminhamento do tronco da árvore de 30 cm. A velocidade de deslocamento do pulverizador de 5 km h-1 proporcionou melhores condições para que os herbicidas estudados apresentassem melhor controle de plantas daninhas, quando comparada com a velocidade de deslocamento do pulverizador de 4 km h-1.