Progress in a-Si:H/c-Si heterojunction emitters obtained by Hot-Wire CVD at 200°C

In this work, we investigate heterojunction emitters deposited by Hot-Wire CVD on p-type crystalline silicon. The emitter structure consists of an n-doped film (20 nm) combined with a thin intrinsic hydrogenated amorphous silicon buffer layer (5 nm). The microstructure of these films has been studied by spectroscopic ellipsometry in the UV-visible range. These measurements reveal that the microstructure of the n-doped film is strongly influenced by the amorphous silicon buffer. The Quasy-Steady-State Photoconductance (QSS-PC) technique allows us to estimate implicit open-circuit voltages near 700 mV for heterojunction emitters on p-type (0.8 Ω·cm) FZ silicon wafers. Finally, 1 cm 2 heterojunction solar cells with 15.4% conversion efficiencies (total area) have been fabricated on flat p-type (14 Ω·cm) CZ silicon wafers with aluminum back-surface-field contact.

Kalvojen vertailu heran nanosuodatuksessa

Työssä verrattiin kaupallisia nanosuodatuskalvoja heran konsentroinnissa. Tutkitut kalvot olivat Desal-5 DK, NF45 ja Koch SR1. NF45-kalvosta tutkittiin kahta eri sukupolven kalvoa. Konsentrointiajoja tehtiin sekä laboratoriomittakaavan levysuotimella että pilot-mittakaavan spiraalimoduulilaitteella. Lisäksi tutkittiin juoksute- ja happoheran konsentrointien eroja. Erityistä huomiota kiinnitettiin permeaattivuon arvoihin konsentroinnissa ja kalvojen suolojen ja laktoosin pidätyskykyyn. NF45-kalvon uuden sukupolven malli osoittautui mittauksissa samankaltaiseksi suolojen ja laktoosin pidätyskyvyltään kuin Desal-5 DK. Koch SR1-kalvo, jonka suolojen ja laktoosin pidätyskyky on Desal-5 DK-kalvoa heikompi, puolestaan vastaa ominaisuuksiltaan NF45 vanhan sukupolven kalvoa. Vanhan sukupolven NF45-kalvon valmistus on loppunut keväällä 2000. Vaihdettaessa vanhan sukupolven NF45-kalvot uuden sukupolven kalvoihin on odotettavissa pienemmät permeaattivuot ja suuremmat suolojen ja laktoosin retentiot kuin aiemmin NF45-kalvolla. Juoksuteheran konsentroinnissa suurimmat permeaattivuot saatiin Koch SR1-kalvolla. Levysuotimella ja spiraalimoduulilla saadaan koostumukseltaan samanlainen juoksuteheratiiviste. Levysuotimella permeaattivuot ovat samalla konsentrointikertoimella suuremmat kuin spiraalimoduulilla. Tämä johtuu spiraalimoduuliin jäävistä kuolleista alueista, joissa ei ole virtausta. Uutta prosessia suunniteltaessa voidaan käyttää laboratoriomittakaavan levysuodinkokokeita, kun halutaan tietoa saatavan tuotteen koostumuksesta. Prosessin tuotantokapasiteetin arvioimiseen tarvitaan pilot-mittakaavan spiraalimoduulikokeita. Happoheratiiviste sisältää enemmän suoloja kuin samalla kalvolla valmistettu juoksuteheratiiviste. Tämä johtuu happoheran juoksuteheraa suuremmasta suolapitoisuudesta. Lisäksi happoheran konsentroinnin permeaattivuo on pienempi kuin juoksuteheran permeaattivuo, sillä happoheran alhainen pH, noin 4,5, vaikuttaa kalvon permeabiliteettiin heikentävästi.

Classification-Based compression of Multispectral Images

The purpose of this thesis is to present a new approach to the lossy compression of multispectral images. Proposed algorithm is based on combination of quantization and clustering. Clustering was investigated for compression of the spatial dimension and the vector quantization was applied for spectral dimension compression. Presenting algo¬rithms proposes to compress multispectral images in two stages. During the first stage we define the classes' etalons, another words to each uniform areas are located inside the image the number of class is given. And if there are the pixels are not yet assigned to some of the clusters then it doing during the second; pass and assign to the closest eta¬lons. Finally a compressed image is represented with a flat index image pointing to a codebook with etalons. The decompression stage is instant too. The proposed method described in this paper has been tested on different satellite multispectral images from different resources. The numerical results and illustrative examples of the method are represented too.

En face optical coherence tomography of foveal microstructure in full-thickness macular hole: a model to study perifoveal müller cells.

PURPOSE: To characterize perifoveal intraretinal cavities observed around full-thickness macular holes (MH) using en face optical coherence tomography and to establish correlations with histology of human and primate maculae. DESIGN: Retrospective nonconsecutive observational case series. METHODS: Macular en face scans of 8 patients with MH were analyzed to quantify the areas of hyporeflective spaces, and were compared with macular flat mounts and sections from 1 normal human donor eye and 2 normal primate eyes (Macaca fascicularis). Immunohistochemistry was used to study the distribution of glutamine synthetase, expressed by Müller cells, and zonula occludens-1, a tight-junction protein. RESULTS: The mean area of hyporeflective spaces was lower in the inner nuclear layer (INL) than in the complex formed by the outer plexiform (OPL) and the Henle fiber layers (HFL): 5.0 × 10(-3) mm(2) vs 15.9 × 10(-3) mm(2), respectively (P < .0001, Kruskal-Wallis test). In the OPL and HFL, cavities were elongated with a stellate pattern, whereas in the INL they were rounded and formed vertical cylinders. Immunohistochemistry confirmed that Müller cells followed a radial distribution around the fovea in the frontal plane and a "Z-shaped" course in the axial plane, running obliquely in the OPL and HFL and vertically in the inner layers. In addition, zonula occludens-1 co-localized with Müller cells within the complex of OPL and HFL, indicating junctions in between Müller cells and cone axons. CONCLUSION: The dual profile of cavities around MHs correlates with Müller cell morphology and is consistent with the hypothesis of intra- or extracellular fluid accumulation along these cells.

Desempenho da tangerineira 'Span Americana' em diferentes porta-enxertos

Este trabalho objetivou avaliar o crescimento vegetativo, a produção e a qualidade de frutos da tangerina 'Span Americana' em diferentes porta-enxertos, nas condições edafoclimáticas de Bebedouro-SP. O plantio foi realizado em junho de 2003, em espaçamento de 6,0 m x 3,0 m, sendo utilizada irrigação por gotejamento a partir de 2006. Os porta-enxertos avaliados foram: citranges [Citrus sinensis (L.) Osbeck × Poncirus trifoliata L. Raf] 'Carrizo' e 'Troyer', tetraploides; trifoliatas (P. trifoliata) 'Davis A' e 'Flying Dragon'; limão Volkameriano Catania 2 (C. volkameriana Tenn. et Pasq.), HRS 849 [(C. aurantium L. cv. 'Smooth Flat Seville' x P. trifoliata cv. 'Argentina')], tangelo 'Orlando' (C. reticulata Blanco × C. paradisi Macf.) e limão 'Cravo' (C. limonia Osbeck). Foram avaliadas a produção acumulada, a eficiência produtiva e a precocidade de entrada em produção, no período de 2007 a 2009. Avaliaram-se, também, as dimensões das plantas e a taxa média de crescimento das plantas no período de 2005 a 2008, além da qualidade dos frutos em 2006 e 2007. Em pomares irrigados de tangerineira 'Span Americana', os porta-enxertos trifoliata 'Davis A' e HRS 849 apresentam desempenho horticultural satisfatório. Para plantio em alta densidade, a melhor performance da tangerineira 'Span Americana' é obtida com a utilização dos porta-enxertos trifoliata 'Flying Dragon' e citranges 'Troyer' e 'Carrizo'.

Stability of hydrogenated nanocrystalline silicon thin-film transistors

Hydrogenated nanocrystalline silicon thin-films were obtained by catalytic chemical vapour deposition at low substrate temperatures (150°C) and high deposition rates (10 Å/s). These films, with crystalline fractions over 90%, were incorporated as the active layers of bottom-gate thin-film transistors. The initial field-effect mobilities of these devices were over 0.5 cm 2/V s and the threshold voltages lower than 4 V. In this work, we report on the enhanced stability of these devices under prolonged times of gate bias stress compared to amorphous silicon thin-film transistors. Hence, they are promising candidates to be considered in the future for applications such as flat-panel displays.

Pellettien laatu ja ominaisuudet eri raaka-aineilla ja niiden seoksilla

Diplomityö tehtiin osana Vapon toteuttamaa monivuotista pelletin kehitysohjelmaa. Kehitysohjelma koostuu useista pienemmistä osaprojekteista, jotka täydentävät toinen toisiaan. Pellettien raaka-ainepohjan laajentaminen on eräs näistä osaprojekteista. Tutkimustyön tavoitteena oli selvittää erilaisten potentiaalisten bioraaka-aineiden soveltuvuutta pelletointiin joko sellaisenaan tai erilaisina seoksina. Raaka-aineiden pelletoitavuutta tutkittiin kenttäolosuhteissa mobiilipelletointilaitoksella. Laitoksen pääkomponentit muodostivat Kahl C 38–780 tasomatriisipuristin, jäähdytin ja täryseula. Pelletointikokeissa tutkittuja raaka-aineita olivat mäntysahanpuru, männynkuori, harvennusranka, haapa, koivu, jyrsinturve ja ruokohelpi. Raaka-aineiden irtotiheys käyttökosteudessa vaihteli välillä 73–244 kg/m3 ja keskimääräinen kosteuspitoisuus 6,5–15 %. Useissa tapauksissa säkitettyjä raaka-aineita säkkikostutettiin haluttuun kosteuspitoisuuteen ennen pelletointia. Säkkikostutettujen raaka-aineiden kosteuspitoisuudet vaihtelivat tällöin välillä 12–14 m- %. Valtaosa tutkituista raaka-aineista ja niiden seoksista pystyttiin pelletoimaan puristimen matriisilla 8/40 mm, jossa puristuskanavan halkaisija oli 8 mm ja kanavan suoran osan pituus 40 mm. Vaikeuksia tuotti ainoastaan pelkän koivupurun ja ruokohelven pelletointi. Käytetty matriisi oli kanavapituudeltaan liian pitkä koivupurun pelletointiin nostaen puristusvastuksen suureksi. Ruokohelven pelletoinnin vaikeudet johtuivat pääasiassa pelletointiin liian karkeasta raaka-aineesta. Myös matriisia 8/55 mm kokeiltiin, mutta se osoittautui liian ”tiukaksi” valtaosalle puuraaka-aineista. Ainoastaan jyrsinturpeen pelletointi onnistui tällä matriisilla. Männynkuoren pelletointia ei matriisilla 8/55 mm yritetty. Kenttäkokeissa valmistetuista pelleteistä määritettiin erilaisia ominaisuuksia, kuten keskipituus, kosteuspitoisuus, irtotiheys, hienoaineksen määrä ja käsittelykestävyys. Lujuus mitattiin sekä Ligno-testillä että CEN-rummutuslujuuden määrityksellä. Lisäksi pelleteille määritettiin alkuaineanalyysi, tuhkapitoisuus ja lämpöarvo ENAS Oy:n laboratoriossa Jyväskylässä. Ligno-testauksessa parhaimman luokan pelletin tulee yltää arvoon 97,5 %. Pelletoitaessa raaka-aineita ja niiden seoksia tasomatriisikoneella sopivalla matriisilla yllettiin usein näihin tai parempiin tuloksiin. Puumateriaaleilla raaka-aineen optimaalinen lähtökosteus oli välillä 12–14 m- % ja turpeella sekä ruokohelvellä 14–16 m- %. Pelletointi onnistui tällöin vaivattomasti, kunhan sopivat puristimen ajoparametrit oli löydetty. Pellettiä alkoi muodostua matriisin puristuskanavien lämpötilan kohotessa noin 70 ºC. Pellettien lämpötila stabiilitilanteessa heti pelletoinnin jälkeen oli useissa tapauksissa 80–90 ºC. Pelletoinnin aikainen tehontarve vaihteli välillä 90–150 kWh/t, ollen suurimmillaan irtotiheydeltään keveillä materiaaleilla. Raaka-aineen suuri partikkelikoko kasvatti puristimen tehontarvetta. Tämä havaittiin selvästi lisättäessä karkeaa ruokohelpisilppua eri raaka-aineiden joukkoon. Kestävyydeltään erinomaisia pellettejä saatiin, kun raaka-aineena oli jyrsinturve, harvennusranka tai mäntypuru. Varsinkin jyrsinturpeen ja harvennusrangan seoksesta valmistetut pelletit osoittautuivat erittäin kestäviksi. Myös jyrsinturpeen ja ruokohelven sekä mäntypurun ja ruokohelven seoksien pelleteille määritettiin hyviä kestävyysarvoja. Männynkuoresta valmistetut pelletit jäivät Ligno-testauksessa kestävyydeltään alle 97,5 % rajan. Pääsyynä tähän oli kuoren pelletointiin käytetyn matriisin 8/40 mm liian lyhyet puristuskanavat.

Microcrystalline silicon thin film transistors obtained by Hot-Wire CVD

Polysilicon thin film transistors (TFT) are of great interest in the field of large area microelectronics, especially because of their application as active elements in flat panel displays. Different deposition techniques are in tough competition with the objective to obtain device-quality polysilicon thin films at low temperature. In this paper we present the preliminary results obtained with the fabrication of TFT deposited by hot-wire chemical vapor deposition (HWCVD). Some results concerned with the structural characterization of the material and electrical performance of the device are presented.

Top-gate microcrystalline silicon TFTs processed at low temperature (<200ºC)

N-type as well P-type top-gate microcrystalline silicon thin film transistors (TFTs) are fabricated on glass substrates at a maximum temperature of 200 °C. The active layer is an undoped μc-Si film, 200 nm thick, deposited by Hot-Wire Chemical Vapor. The drain and source regions are highly phosphorus (N-type TFTs) or boron (P-type TFTs)-doped μc-films deposited by HW-CVD. The gate insulator is a silicon dioxide film deposited by RF sputtering. Al-SiO 2-N type c-Si structures using this insulator present low flat-band voltage,-0.2 V, and low density of states at the interface D it=6.4×10 10 eV -1 cm -2. High field effect mobility, 25 cm 2/V s for electrons and 1.1 cm 2/V s for holes, is obtained. These values are very high, particularly the hole mobility that was never reached previously.

A Feedfordward Adaptive Controller to Reduce the Imaging Time of Large-Sized Biological Samples with a SPM-Based Multiprobe Station

The time required to image large samples is an important limiting factor in SPM-based systems. In multiprobe setups, especially when working with biological samples, this drawback can make impossible to conduct certain experiments. In this work, we present a feedfordward controller based on bang-bang and adaptive controls. The controls are based in the difference between the maximum speeds that can be used for imaging depending on the flatness of the sample zone. Topographic images of Escherichia coli bacteria samples were acquired using the implemented controllers. Results show that to go faster in the flat zones, rather than using a constant scanning speed for the whole image, speeds up the imaging process of large samples by up to a 4x factor.

Beyond contact-based transmission networks: the role of spatial coincidence.

Animal societies rely on interactions between group members to effectively communicate and coordinate their actions. To date, the transmission properties of interaction networks formed by direct physical contacts have been extensively studied for many animal societies and in all cases found to inhibit spreading. Such direct interactions do not, however, represent the only viable pathways. When spreading agents can persist in the environment, indirect transmission via 'same-place, different-time' spatial coincidences becomes possible. Previous studies have neglected these indirect pathways and their role in transmission. Here, we use rock ant colonies, a model social species whose flat nest geometry, coupled with individually tagged workers, allowed us to build temporally and spatially explicit interaction networks in which edges represent either direct physical contacts or indirect spatial coincidences. We show how the addition of indirect pathways allows the network to enhance or inhibit the spreading of different types of agent. This dual-functionality arises from an interplay between the interaction-strength distribution generated by the ants' movement and environmental decay characteristics of the spreading agent. These findings offer a general mechanism for understanding how interaction patterns might be tuned in animal societies to control the simultaneous transmission of harmful and beneficial agents.

A comprehensive model for quantum noise characterization in digital mammography.

NlmCategory="UNASSIGNED">A version of cascaded systems analysis was developed specifically with the aim of studying quantum noise propagation in x-ray detectors. Signal and quantum noise propagation was then modelled in four types of x-ray detectors used for digital mammography: four flat panel systems, one computed radiography and one slot-scan silicon wafer based photon counting device. As required inputs to the model, the two dimensional (2D) modulation transfer function (MTF), noise power spectra (NPS) and detective quantum efficiency (DQE) were measured for six mammography systems that utilized these different detectors. A new method to reconstruct anisotropic 2D presampling MTF matrices from 1D radial MTFs measured along different angular directions across the detector is described; an image of a sharp, circular disc was used for this purpose. The effective pixel fill factor for the FP systems was determined from the axial 1D presampling MTFs measured with a square sharp edge along the two orthogonal directions of the pixel lattice. Expectation MTFs were then calculated by averaging the radial MTFs over all possible phases and the 2D EMTF formed with the same reconstruction technique used for the 2D presampling MTF. The quantum NPS was then established by noise decomposition from homogenous images acquired as a function of detector air kerma. This was further decomposed into the correlated and uncorrelated quantum components by fitting the radially averaged quantum NPS with the radially averaged EMTF(2). This whole procedure allowed a detailed analysis of the influence of aliasing, signal and noise decorrelation, x-ray capture efficiency and global secondary gain on NPS and detector DQE. The influence of noise statistics, pixel fill factor and additional electronic and fixed pattern noises on the DQE was also studied. The 2D cascaded model and decompositions performed on the acquired images also enlightened the observed quantum NPS and DQE anisotropy.

No Accumulation of Transposable Elements in Asexual Arthropods.

Transposable elements (TEs) and other repetitive DNA can accumulate in the absence of recombination, a process contributing to the degeneration of Y-chromosomes and other nonrecombining genome portions. A similar accumulation of repetitive DNA is expected for asexually reproducing species, given their entire genome is effectively nonrecombining. We tested this expectation by comparing the whole-genome TE loads of five asexual arthropod lineages and their sexual relatives, including asexual and sexual lineages of crustaceans (Daphnia water fleas), insects (Leptopilina wasps), and mites (Oribatida). Surprisingly, there was no evidence for increased TE load in genomes of asexual as compared to sexual lineages, neither for all classes of repetitive elements combined nor for specific TE families. Our study therefore suggests that nonrecombining genomes do not accumulate TEs like nonrecombining genomic regions of sexual lineages. Even if a slight but undetected increase of TEs were caused by asexual reproduction, it appears to be negligible compared to variance between species caused by processes unrelated to reproductive mode. It remains to be determined if molecular mechanisms underlying genome regulation in asexuals hamper TE activity. Alternatively, the differences in TE dynamics between nonrecombining genomes in asexual lineages versus nonrecombining genome portions in sexual species might stem from selection for benign TEs in asexual lineages because of the lack of genetic conflict between TEs and their hosts and/or because asexual lineages may only arise from sexual ancestors with particularly low TE loads.

Defeitos superficiais em 2H-WS2 observados por microscopia de tunelamento

Scanning tunnelling microscopy (STM) was used to characterise the basal surface of fresh cleaved crystals of 2H-WS2. Although no impurity or stacking faults could be detected by X-ray diffraction, STM images obtained with negative bias voltage showed two kinds of defects. These defects were attributed to an iodine derivative used as transport agent. In a flat surface free of defects, an image with atomic resolution was achieved with sulphur distances and angles as expected for hexagonal symmetry of 2H-WS2.

Tasolohkolinjan läpäisyaikojen tarkastelu ja kehittäminen Lean management periaatteita soveltaen

Diplomityön tavoitteena oli Aker Yardsin Turun telakan tasolohkolinjan läpäisyajan parantaminen. Työssä selvitettiin lohkotehtaan nykyinen läpimenoaika ja pyrittiin parantamaan sitä Lean management periaatteita soveltaen. Työssä suoritettiin perusteellinen työntutkimus yhdessä työnjohdon kanssa, jossa selvitettiin eri työvaiheiden läpimenoajat ja työtunnit. Tuloksista löydettiin kolme selvää kehityskohdetta, joilla saadaan nykyistä läpimenoaikaa ja alihankintakustannuksia pienemmäksi. Nämä kehityskohteet olivat jäykkääjien asennuksen ja hitsauksen parantaminen, myynnin jälkeisten töiden minimointi sekä nostotukien asennuksen tehostaminen. Lisäksi tutkimustyön ohella havaittiin neljäs kehityskohde, osavalmistuksen ajoittaminen oikeaan aikaan. Tämä ei tullut ilmi tutkimustuloksista vaan ihmisiä haastattelemalla. Kehityskohtien tunnistamisen perusteella luotiin investointiehdotus jäykkääjien toiminnan tehostamiseen, sekä uusia toimintatapoja myynnin jälkeisten töiden minimoimiseksi ja nostotukien asennuksen tehostamiseksi. Osavalmistuksen ajoittamisella oikeaan aikaan, pyritään tehostamaan toimintaa lohkonkoontipaikalla.