The influence of different co-catalysts in Pt-based ternary and quaternary electro-catalysts on the electro-oxidation of methanol and ethanol in acid media

One of the key objectives in fuel cell technology is to reduce Pt loading by the improvement of its catalytic activity towards alcohol oxidation. Here, a sol-gel based method was used to prepare ternary and quaternary carbon supported nanoparticles by combining Pt-Ru with Mo, Ta, Pb, Rh or Ir, which were used as electro-catalysts for the methanol and ethanol oxidation reactions in acid medium. Structural characterization performed by XRD measurements revealed that crystalline structures with crystallites ranging from 2.8 to 4.1 nm in size and with different alloy degrees were produced. Tantalum and lead deposited as a heterogeneous mixture of oxides with different valences resulting in materials with complex structures. The catalysts activities were evaluated by cyclic voltammetry and by Tafel plots and the results showed that the activity towards methanol oxidation was highly dependent of the alloy degree, while for ethanol the presence of a metal capable to promote the break of C-C bond, such as Rh, was necessary for a good performance. Additionally, the catalysts containing of TaOx or PbOx resulted in the best materials due to different effects: the hi-functional mechanism promoted by TaOx and a better dispersion of the catalysts constituents promoted by PbOx. (C) 2012 Elsevier B.V. All rights reserved.

Vanadium and Titanium Mixed Oxide Films: Synthesis, Characterization and Application as Ion Sensor

Vanadium/titanium mixed oxide films were produced using the sol-gel route. The structural investigation revealed that increased TiO2 molar ratio in the mixed oxide disturbs the V2O5 crystalline structure and makes it amorphous. This blocks the TiO2 phase transformation, so TiO2 stabilizes in the anatase phase. In addition the surface of the sample always presents larger amounts of TiO2 than expected, revealing a concentration gradient along the growth direction. For increased TiO2 molar ratios the roughness of the surface is reduced. Ion sensors were fabricated using the extended gate field effect transistor configuration. The obtained sensitivities varied in the range of 58 mV/pH down to 15 mV/pH according to the composition and morphology of the surface of the samples. Low TiO2 amounts presented better sensing properties that might be related to the cracked and inhomogeneous surfaces. Rising the TiO2 quantity in the films produces homogeneous surfaces but diminishes their sensitivities. Thus, the present paper reveals that the compositional and structural aspects change the surface morphology and electrical properties accounting for the final ion sensing properties of the V2O5/TiO2 films. (C) 2012 The Electrochemical Society. [DOI: 10.1149/2.053206jes] All rights reserved.

Influence of titanium and lutetium on the persistent luminescence of ZrO2

Non-doped as well as titanium and lutetium doped zirconia (ZrO2) materials were synthesized via the sol-gel method and structurally characterized with X-ray powder diffraction. The addition of Ti in the zirconia lattice does not change the crystalline structure whilst the Lu doping introduces a small fraction of the tetragonal phase. The UV excitation results in a bright white-blue luminescence at ca. 500 nm for all the materials which emission could be assigned to the Ti3+ e(g) -> t(2g) transition. The persistent luminescence originates from the same Ti3+ center. The thermoluminescence data shows a well-defined though rather similar defect structures for all the zirconia materials. The kinetics of persistent luminescence was probed with the isothermal decay curve analyses which indicated significant retrapping. The short duration of persistent luminescence was attributed to the quasi-continuum distribution of the traps and to the possibility of shallow traps even below the room temperature. (C) 2012 Optical Society of America

STRATEGIES FOR PREPARATION OF MOLECULARLY IMPRINTED POLYMERS MODIFIED ELECTRODES AND THEIR APPLICATION IN ELECTROANALYSIS: A REVIEW

Molecularly imprinted polymers (MIP's) have been applied in several areas of analytical chemistry, including the modification of electrodes. The main purpose of such modification is improving selectivity; however, a gain in sensitivity was also observed in many cases. The most frequent approaches for these modifications are the electrodeposition of polymer films and sol gel deposits, spin and drop coating and self-assembling of films on metal nanoparticles. The preparation of bulk (body) modified composites as carbon pastes and polymer agglutinated graphite have also been investigated. In all cases several analytes including pharmaceuticals, pesticides, and inorganic species, as well as molecules with biological relevance have been successfully used as templates and analyzed with such devices in electroanalytical procedures. Herein, 65 references are presented concerning the general characteristics and some details related to the preparation of MIP's including a description of electrodes modified with MIP's by different approaches. The results using voltammetric and amperometric detection are described.

Self-supported bacterial cellulose/boehmite organic-inorganic hybrid films

Self-supported organic-inorganic hybrid transparent films have been prepared from bacterial cellulose and boehmite. SEM results indicate that the BC membranes are covered by Boehmite and XRD patterns suggest structural changes on cellulose due to Boehmite addition. Thermal stability is accessed through TG curves and is dependent on Boehmite content. Transparency, as evaluated by UV-Vis absorption, increases with increasing content of boehmite suggesting application of these materials as transparent substrates for opto-electronic devices.

Síntesis y caracterización de fotocatalizadores basados en TiO2 : estudios de la degradación de los herbicidas ácido 2,4-Diclorofenoxiacético y bentazona mediante fotocatálisis heterogénea a escala de laboratorio y planta piloto solar

Programa de doctorado: Ingeniería ambiental y desalinización

Approccio colloidale per la preparazione di fotocatalizzatori nanostrutturati a base di TiO2

Oggigiorno si osserva a livello mondiale un continuo aumento dei consumi di acqua per uso domestico, agricolo ed industriale che dopo l’impiego viene scaricata nei corpi idrici (laghi, fiumi, torrenti, bacini, ecc) con caratteristiche chimico fisiche ed organolettiche completamente alterate, necessitando così di specifici trattamenti di depurazione. Ricerche relative a metodi di controllo della qualità dell’acqua e, soprattutto, a sistemi di purificazione rappresentano pertanto un problema di enorme importanza. I trattamenti tradizionali si sono dimostrati efficienti, ma sono metodi che operano normalmente trasferendo l’inquinante dalla fase acquosa contaminata ad un’altra fase, richiedendo perciò ulteriori processi di depurazione. Recentemente è stata dimostrata l’efficacia di sistemi nano strutturati come TiO2-Fe3O4 ottenuto via sol-gel, nella foto-catalisi di alcuni sistemi organici. Questo lavoro di tesi è rivolto alla sintesi e caratterizzazione di un catalizzatore nanostrutturato composito costituito da un core di Fe3O4 rivestito da un guscio di TiO2 separate da un interstrato inerte di SiO2, da utilizzare nella foto-catalisi di sistemi organici per la depurazione delle acque utilizzando un metodo di sintesi alternativo che prevede un “approccio” di tipo colloidale. Partendo da sospensioni colloidali dei diversi ossidi, presenti in commercio, si è condotta la fase di deposizione layer by layer via spray drying, sfruttando le diverse cariche superficiali dei reagenti. Questo nuovo procedimento permette di abbattere i costi, diminuire i tempi di lavoro ed evitare possibili alterazioni delle proprietà catalitiche della titania, risultando pertanto adatto ad una possibile applicazione su scala industriale. Tale sistema composito consente di coniugare le proprietà foto-catalitiche dell’ossido di titanio con le proprietà magnetiche degli ossidi di ferro permettendo il recupero del catalizzatore a fine processo. Il foto-catalizzatore è stato caratterizzato durante tutte la fasi di preparazione tramite microscopia SEM e TEM, XRF, Acusizer, spettroscopia Raman e misure magnetiche. L’attività foto-calitica è stata valutata con test preliminari utilizzando una molecola target tipo il rosso di metile in fase acquosa. I risultati ottenuti hanno dimostrato che il sistema core-shell presenta inalterate sia le proprietà magnetiche che quelle foto-catalitiche tipiche dei reagenti.

Solvatationsdynamik: lokales Relaxationsverhalten glasbildender Systeme

In dieser Arbeit wurde das lokale Relaxationsverhalten niedermolekularer glasbildender Materialien mit der Methode der Solvatationsdynamik untersucht. Bei dieser Methode werden phosphoreszente Farbstoffe als molekulare Sonden für die lokale Dynamik im Glasbildner eingesetzt. Je nach verwendeter Sonde sind unterschiedliche Eigenschaften zugänglich:Mit Farbstoffen, die ihr Dipolmoment bei optischer Anregung nicht ändern, wird eine mechanische Solvatation gemessen, die die lokale viskoelastische Antwort des Materials widerspiegelt. Mit Farbstoffen, die eine Änderung des Dipolmoments bei optischer Anregung aufweisen,sind zusätzlich lokale dielektrische Eigenschaften des Materials zugänglich, die bei endlicher Polarität des Lösungsmittels dominieren. Das heterogene Relaxationsverhalten des Glasbildners 2-Methyltetrahydrofuran wurde quantitativ untersucht.Auf einem Temperaturbereich, auf dem die mittlere Relaxationszeit um mehr als 4 Dekaden variiert, konnte gezeigt werden, daß die Relaxation lokal rein exponentiell verläuft. Zur Abschätzung von Reichweiteneffekten wurden Solvatationsmessungen in einschränkenden Geometrien in Form von porösen Sol-Gel Gläsern mit Porendurchmessern zwischen 7,5-2,5 nm durchgeführt. Der Einfluß der Beschaffenheit der Porenoberfläche wurde durch Vergleichzwischen der Solvatation in nativen und in silanisierten Gläsern untersucht. Es wurde gezeigt, daß auch in den kleinsten verwendeten silanisierten Poren alle Charakteristika des jeweiligen Bulk-Systems erhalten bleiben.In den nativen porösen Gläsern dagegen führt der Einfluß der stark polaren Oberfläche zu einer Änderung der Dynamik.

Sintesi e caratterizzazione di La0.4Sr0.4TiO3 (LST) come anodo innovativo per celle a combustibile ad ossido solido (SOFC)

Le celle a combustibile ad ossido solido (SOFC) sono reattori elettrochimici che convertono l’energia chimica di un gas combustibile direttamente in energia elettrica con un’alta efficienza e con basse emissioni. Il materiale più comunemente usato come anodo, il Ni/YSZ cermet, mostra però numerosi svantaggi nell’applicazione quali la suscettibilità all’avvelenamento da zolfo e la deposizione di coke per cracking degli idrocarburi usati come combustibile. E’ perciò necessario sviluppare materiali alternativi che sopperiscano a questi problemi. Il titanato di stronzio drogato con lantanio con stechiometria La0.4Sr0.4TiO3 (LST) è stato scelto come anodo alternativo per le ottime proprietà possedute. Lo scopo del lavoro di tesi è stato quindi lo studio dell’influenza della natura dei precursori, delle condizioni di sintesi e dell’aggiunta di agenti porizzanti necessari per l’ottenimento della fase perovskitica pura e con porosità controllata. In un primo tempo è stata verificata la possibilità di ottenere la fase La0.4Sr0.4TiO3 pura mediante sintesi allo stato solido, trattando termicamente miscele di precursori diversi. I risultati ottenuti hanno evidenziato che l’utilizzo di nitrati metallici porta a risultati migliori rispetto all’utilizzo di carbonati ed ossidi poiché permette la formazione della fase perovskite a temperature inferiori e con una purezza maggiore. Poiché l’analisi elementare sui materiali preparati in questa prima fase ha evidenziato un problema sulla stechiometria, il metodo di sintesi è stato ottimizzato solubilizzando preventivamente i precursori di lantanio e stronzio e determinandone il titolo mediante ICP. Inoltre, sono state effettuate delle sintesi utilizzando TiO2 a diversa area superficiale, per verificare l’effetto sulle fasi formate di una maggior reattività di questo componente. Per completezza la perovskite è stata sintetizzata anche tramite sintesi sol-gel, utilizzando il metodo Pechini, ottenendo a 700°C la fase pura. L’analisi morfologica ha evidenziato che le polveri con caratteristiche migliori per la formatura sono quelle ottenute tramite sintesi allo stato solido. Le pastiglie prodotte, miscelando tali polveri e agenti porizzanti opportuni, hanno evidenziato la stabilità della fase perovskitica voluta ma anche la necessità di ottimizzare l’aggiunta del porizzante per avere una porosità adeguata all’applicazione del sistema quale anodo SOFC.

Tetrafenilciclopentadienon-derivati ed analoghi: sintesi, "self-assembly" e caratterizzazione reologica

Gels are materials that are easier to recognize than to define. For all practical purpose, a material is termed a gel if the whole volume of liquid is completely immobilized as usually tested by the ‘tube inversion’ method. Recently, supramolecular gels obtained from low molecular weight gelators (LMWGs) have attracted considerable attention in materials science since they represent a new class of smart materials sensitive to external stimuli, such as temperature, ultrasounds, light, chemical species and so on. Accordingly, during the past years a large variety of potentialities and applications of these soft materials in optoelectronics, as electronic devices, light harvesting systems and sensors, in bio-materials and in drug delivery have been reported. Spontaneous self-assembly of low molecular weight molecules is a powerful tool that allows complex supramolecular nanoscale structures to be built. The weak and non-covalent interactions such as hydrogen bonding, π–π stacking, coordination, electrostatic and van der Waals interactions are usually considered as the most important features for promoting sol-gel equilibria. However, the occurrence of gelation processes is ruled by further “external” factors, among which the temperature and the nature of the solvents that are employed are of crucial importance. For example, some gelators prefer aromatic or halogenated solvents and in some cases both the gelation temperature and the type of the solvent affect the morphologies of the final aggregation. Functionalized cyclopentadienones are fascinating systems largely employed as building blocks for the synthesis of polyphenylene derivatives. In addition, it is worth noting that structures containing π-extended conjugated chromophores with enhanced absorption properties are of current interest in the field of materials science since they can be used as “organic metals”, as semiconductors, and as emissive or absorbing layers for OLEDs or photovoltaics. The possibility to decorate the framework of such structures prompted us to study the synthesis of new hydroxy propargyl arylcyclopentadienone derivatives. Considering the ability of such systems to give π–π stacking interactions, the introduction on a polyaromatic structure of polar substituents able to generate hydrogen bonding could open the possibility to form gels, although any gelation properties has been never observed for these extensively studied systems. we have synthesized a new class of 3,4-bis (4-(3-hydroxy- propynyl) phenyl) -2, 5-diphenylcyclopentadienone derivatives, one of which (1a) proved to be, for the first time, a powerful organogelator. The experimental results indicated that the hydroxydimethylalkynyl substituents are fundamental to guarantee the gelation properties of the tetraarylcyclopentadienone unit. Combining the results of FT-IR, 1H NMR, UV-vis and fluorescence emission spectra, we believe that H-bonding and π–π interactions are the driving forces played for the gel formation. The importance of soft materials lies on their ability to respond to external stimuli, that can be also of chemical nature. In particular, high attention has been recently devoted to anion responsive properties of gels. Therefore the behaviour of organogels of 1a in toluene, ACN and MeNO2 towards the addition of 1 equivalent of various tetrabutylammonium salts were investigated. The rheological properties of gels in toluene, ACN and MeNO2 with and without the addition of Bu4N+X- salts were measured. In addition a qualitative analysis on cation recognition was performed. Finally the nature of the cyclic core of the gelator was changed in order to verify how the carbonyl group was essential to gel solvents. Until now, 4,5-diarylimidazoles have been synthesized.

Untersuchungen zur Löslichkeit von Kobalt und Eisen in TiO 2-Bulk sowie in TiO 2-Nanoproben und deren Einfluss auf die magnetischen Eigenschaften

Co- und Fe-dotierte Rutil- und Anatas-Bulkproben wurden über einen Sol-Gel Prozess und anschließende thermische Behandlung dargestellt und auf ihre Zugehörigkeit zu der Gruppe der verdünnten magnetischen Oxide untersucht. Die Untersuchungen der dotierten Rutil-Proben mittels Röntgenbeugung, Elektronenmikroskopie und magnetischen Methoden zeigen, dass die Löslichkeit von Co und Fe in der TiO2-Modifikation Rutil sehr gering ist. Oberhalb von 1at% Co bzw. Fe wird neben Rutil die Bildung der Oxide CoTiO3 bzw. Fe2TiO5 beobachtet. Weitere thermische Behandlung im Argon-H2-Strom führte aufgrund der Bildung von metallischem Co bzw. Fe zu einem ferromagnetischen Verhalten. Die TiO2-Modifikation Anatas besitzt eine höhere Löslichkeit, so dass erst oberhalb von 4at% Co bzw. 10at% Fe die Phasen Co3O4 bzw. FeTiO3 neben Anatas auftreten. Entsprechende Proben zeigen ein paramagnetisches Verhalten. Oberhalb der Löslichkeitsgrenze führt die Reduktion im Argon-H2-Strom zu einem ferromagnetischen Verhalten, welches auf metallisches Co bzw. Fe zurückzuführen ist. Analog zu den Bulkproben wurden Co- und Fe-dotierte TiO2-Nanodrähte hergestellt. Das magnetische Verhalten der Fe-dotierten TiO2-Nanodrähte entspricht dem der Fe-dotierten Anatas-Bulkproben. Dagegen führt die Co-Dotierung nicht zu einem Einbau in die TiO2-Nanodrähte, sondern zur Bildung von CoOx-Nanopartikeln. Die entsprechenden Proben zeigen ein schwach ferromagnetisches Verhalten. Dies ist jedoch nicht auf eine ferromagnetische Dotierung der TiO2-Nanodrähte zurückzuführen, sondern auf nicht kompensierte Momente an den Oberflächen der als Verunreinigungen auftretenden CoOx-Nanopartikel. Zusammenfassend wird festgestellt, dass die Löslichkeit von Co und Fe in TiO2 für die Ausbildung eines ferromagnetischen Verhaltens zu gering ist. Der beobachtete Ferromagnetismus lässt sich eindeutig auf magnetische Verunreinigungen zurückführen. Somit können die dotierten TiO2 Proben nicht den verdünnten magnetischen Oxiden zugeordnet werden.

An alternative blocking layer for titanium dioxide (TiO 2) solar cell applications

In hybrid organic solar cells a blocking layer between transparent electrode and nanocrystalline titania particles is essential to prevent short-circuiting and current loss through recombination at the electrode interface. Here the preparation of a uniform hybrid blocking layer which is composed of conducting titania nanoparticles embedded in an insulating polymer derived ceramic is presented. This blocking layer is prepared by sol-gel chemistry where an amphiphilic block copolymer is used as a templating agent. A novel poly(dimethylsiloxane) containing amphiphilic block copolymer poly(ethyleneglycol)methylethermethacrylate-block-poly(dimethylsiloxane)-block-poly(ethyleneglycol)methylethermethacrylate has been synthesized to act as the templating agent. Plasma treatment uncovered titania surface from any polymer. Annealing at 450°C under nitrogen resulted in anatase titania with polymer derived silicon oxycarbide ceramic. Electrical characterization by conductive scanning probe microscopy experiments revealed a percolating titania network separated by an insulating ceramic matrix. Scanning Kelvin probe force microscopy showed predominant presence of titania particles on the surface creating a large surface area for dye absorption. The uniformity of the percolating structures was proven by microbeam grazing incidence small angle x-ray scattering. First applications in hybrid organic solar cells in comparison with conventional titanium dioxide blocking layer containing devices revealed 15 fold increases in corresponding efficiencies. Poly(dimethylsiloxane)-block-poly(ethyleneglycol)methylethermethacrylate and poly(ethyleneoxide)-poly(dimethylsiloxane)methylmethacrylate diblock copolymers were also synthesized. Their titania nanocomposite films were compared with the integrated blocking layer. Liner poly(ethyleneoxide) containing diblock copolymer resulted in highly ordered foam like structures. The effect of heating temperature rise to 600°C and 1000°C on titania morphology was investigated by scanning electron and force microscopy and x-ray scattering. Sol-gel contents, hydrochloric acid, titania precursor and amphiphilic triblock copolymer were altered to see their effect on titania morphology. Increase in block copolymer content resulted in titania particles of diameter 15-20 nm.

Self assembled materials for solar cell application

In der vorliegenden Arbeit wurden Materialien und Aufbauten für Hybrid Solarzellen entwickelt und erforscht. rnDer Vergleich zweier bekannter Lochleitermaterialien für Solarzellen in einfachen Blend-Systemen brachte sowohl Einsicht zur unterschiedlichen Eignung der Materialien für optoelektronische Bauelemente als auch neue Erkenntnisse in Bereichen der Langzeitstabilität und Luftempfindlichkeit beider Materialien.rnWeiterhin wurde eine Methode entwickelt, um Hybrid Solarzelle auf möglichst unkomplizierte Weise aus kostengünstigen Materialien darzustellen. Die „Eintopf“-Synthese ermöglicht die unkomplizierte Darstellung eines funktionalen Hybridmaterials für die optoelektronische Anwendung. Mithilfe eines neu entwickelten amphiphilen Blockcopolymers, das als funktionelles Templat eingesetzt wurde, konnten mit einem TiO2-Precursor in einem Sol-Gel Ansatz verschiedene selbstorganisierte Morphologien des Hybridmaterials erhalten werden. Verschiedene Morphologien wurden auf ihre Eignung in Hybrid Solarzellen untersucht. Ob und warum die Morphologie des Hybridsystems die Effizienz der Solarzelle beeinflusst, konnte verdeutlicht werden. Mit der Weiterentwicklung der „Eintopf“-Synthese, durch den Austausch des TiO2-Precursors, konnte die Solarzelleneffizienz von 0.15 auf 0.4 % gesteigert werden. Weiterhin konnte die Übertragbarkeit des Systems durch den erfolgreichen Austausch des Halbleiters TiO¬2 mit ZnO bewiesen werden.rn

Sintesi e caratterizzazione di nanoparticelle di ossido di stagno dopate

In the last years, new materials have been developed in the broad area of nanoscience. Among them, an emergent class characterized by excellent electrical conductivity properties as well as high optical transmittance in the visible region are TCOs (Transparent Conducting Oxides). Due to their versatile properties, they have found many applications in a lot of optoelectronic devices, such as solar cells, liquid crystal displays, touch-panel displays, gas sensors, to cite a few examples. Different research groups have studied and characterized the TCOs. In this context, a new synthetic method has been developed to produce FTO nanocrystals (Fluorine-doped Tin Oxide NCs) in Prof. Pinna’s lab at the Humboldt University in Berlin. FTO belongs to the TCO category, and they have been studied as a promising alternative to ITO NCs (Indium Tin Oxide) which represent the standard TCO material in terms of properties and performances. In this work, FTO NCs have been synthesized using the “benzyl alcohol route” (a non-aqueous sol-gel method) via microwave, which permits to produce FTO particles with good properties as revealed by the characterizations performed, employing a cheap, fast and clean method.

Application of a hybrid blocking layer in dye-sensitized solar cells

In dye-sensitized solar cells a blocking layer between the transparent electrode and the mesoporous titanium dioxide film is used to prevent short-circuits between the hole-conductor and the front electrode. The conventional approach is to use a compact layer of titanium dioxide prepared by spin coating or spray pyrolysis. The thickness of the blocking layer is critical. On one hand, the layer has to be thick enough to cover the rough substrate completely. On the other hand, the serial resistance increases with increasing film thickness, because the layer acts as an ohmic resistance itself. In this thesis an amphiphilic diblock copolymer is used as a functional template to produce an alternative, hybrid blocking layer. The hybrid blocking layer is thinner than the conventional, compact titanium dioxide film and thereby possesses a higher conductivity. Still, this type of blocking layer covers the rough electrode material completely and avoids current loss through charge recombination. The novel blocking layer is prepared using a tailored, amphiphilic block copolymer in combination with sol-gel chemistry. While the hydrophilic poly(ethylene oxide) part of the polymer coordinates a titanium dioxide precursor to form a percolating network of titania particles, the hydrophobic poly(dimethylsiloxane) part turns into an insulating ceramic layer. With this technique, crack-free films with a thickness down to 24 nm are obtained. The presence of a conductive titanium dioxide network for current flow, which is embedded in an insulating ceramic material, is validated by conductive scanning force microscopy. This is the first time that such a hybrid blocking layer is implemented in a solar cell. With this approach the efficiency could be increased up to 27 % compared to the conventional blocking layer. Thus, it is demonstrated that the hybrid blocking layer represents a competitive alternative to the classical approach.