Effect of aluminum on the corrosion resistance of low-alloy steel in 10wt% sulfuric acid solution

The aqueous corrosion behavior of low-alloy steel with aluminum contents was examined in a 10 wt% H₂SO₄ (pH 0.13) solution using electrochemical techniques and surface analyses. The corrosion resistance of the new alloy steel was evaluated in terms of electrochemical parameters, such as passive current density, film, and charge transfer resistances. The results showed that a high Al content in the steel imparted better passivation behavior resulting in a lower corrosion rate. It related to the enrichment of iron carbonate and hydrocarbon by the dissolution of the carbide phase.

Effect of gold on the corrosion behavior of an electroless nickel/immersion gold surface finish

The performance of surface finishes as a function of the pH of the utilized plating solution was evaluated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization tests in 3.5 wt.% NaCl solution. In addition, the surface finishes were examined by x-ray diffraction (XRD), and the contact angle of the liquid/solid interface was recorded. NiP films on copper substrates with gold coatings exhibited their highest coating performance at pH 5. This was attributed to the films having the highest protective efficiency and charge transfer resistance, lowest porosity value, and highest contact angle among those examined as a result of the strongly preferred Au(111) orientation and the improved surface wettability.

Effect of prestrain on microstructures and properties of Si-Al-Mn TRIP steel sheet with niobium

Paint baking treatment was carried out in a silicon oil bath at 170 °C for 20 min for Si-Al-Mn TRIP Steel sheet with different prestrains, and effect of prestrain on microstructures and properties was studied before and after baking. The results show that with the increasing of prestrain amount during prestraining and baking, the volume fraction of retained austenite decreases, and the volume fraction of martensite and bainite increases as well as yield strength increases; as prestrain ranges from 0 to 4%, the baking-hardening (BH) value increases; while the prestrain ranges from 4% to 16%, the BH value decreases; when the prestrain amount is 4%, the highest BH value is about 70 MPa for Si-Al-Mn TRIP steel sheet with niobium, which displays excellent baking-hardening behavior.

The effect of obesity on polycystic ovary syndrome : a systematic review and meta-analysis

While many women with polycystic ovary syndrome (PCOS) are overweight, obese or centrally obese, the effect of excess weight on the outcomes of PCOS is inconsistent. The review aimed to assess the effects of overweight, obesity and central obesity on the reproductive, metabolic and psychological features of PCOS. MEDLINE, EMBASE, CINAHL, Cochrane Central Register of Controlled Trials (CENTRAL) and PSYCINFO were searched for studies reporting outcomes according to body mass index categories or body fat distribution. Data were presented as mean difference or risk ratio (95% confidence interval). This review included 30 eligible studies. Overweight or obese women with PCOS had decreased sex hormone-binding globulin (SHBG), increased total testosterone, free androgen index, hirsutism, fasting glucose, fasting insulin, homeostatic model assessment-insulin resistance index and worsened lipid profile. Obesity significantly worsened all metabolic and reproductive outcomes measured except for hirsutism when compared to normal weight women with PCOS. Overweight women had no differences in total testosterone, hirsutism, total-cholesterol and low-density lipoprotein-cholesterol compared to normal weight women and no differences in SHBG and total testosterone compared to obese women. Central obesity was associated with higher fasting insulin levels. These results suggest that prevention and treatment of obesity is important for the management of PCOS.

The effect of microstructure on the decrease of the apparent Young's Modulus in DP 780 steel

Currently, there is a significant effort into developing novel multiphase microstructures to further improve the strength/ductility combination of advanced high-strength steels. To achieve this, the effect of the microstructure on sheet formability needs to be further understood. In this study, the effect of the microstructure on the variation of the elastic modulus in loading and unloading of DP 780 steel has been investigated. Five microstructures with varying volume fractions of ferrite and martensite were generated using different heat treatment cycles. Tension tests were performed to different strain values and the Young’s Modulus during loading and unloading was determined. The test results show that the reduction in unloading modulus with prestrain depends on the volume fraction and hardness of the martensitic phase.