A Note On The Numerical Simulations Of Flow Past A Wavy Square-Section Cylinder

The flow past a square-section cylinder with a geometric disturbance is investigated by numerical simulations. The extra terms, due to the introduction of mapping transformation simulating the effect of disturbance into the transformed Navier-Stokes equations, are correctly derived, and the incorrect ones in the previous literature are pointed out and analyzed. Furthermore, the relationship between the vorticity, especially on the cylinder surface, and the disturbance is derived and explained theoretically. The computations are performed at two Reynolds numbers of 100 and 180 and three amplitudes of waviness of 0.006, 0.025 and 0.167 with another aim to explore the effects of different Reynolds numbers and disturbance on the vortex dynamics in the wake and forces on the body. Numerical results have shown that, at the mild waviness of 0.025, the Karman vortex shedding is suppressed completely for Re = 100, while the forced vortex dislocation is appeared in the near wake at the Reynolds number of 180. The drag reduction is up to 21.6% at Re = 100 and 25.7% at Re = 180 for the high waviness of 0.167 compared with the non-wavy cylinder. The lift and the Strouhal number varied with different Reynolds numbers and the wave steepness are also obtained.

Evolution of thermoplastic shear localization and related microstructures in Awl/SiCp composites under dynamic compression

The localized shear deformation in the 2024 and 2124 Al matrix composites reinforced with SiC particles was investigated with a split Hopkinson pressure bar (SHPB) at a strain rate of about 2.0x10(3) s(-1). The results showed that the occurrence of localized shear deformation is sensitive to the size of SiC particles. It was found that the critical strain, at which the shear localization occurs, strongly depends on the size and volume fraction of SiC particles. The smaller the particle size, the lower the critical strain required for the shear localization. TEM examinations revealed that Al/SiCp interfaces are the main sources of dislocations. The dislocation density near the interface was found to be high and it decreases with the distance from the particles. The Al matrix in shear bands was highly deformed and severely elongated at low angle boundaries. The Al/SiCp interfaces, particularly the sharp corners of SiC particles, provide the sites for microcrack initiation. Eventual fracture is caused by the growth and coalescence of microcracks along the shear bands. It is proposed that the distortion free equiaxed grains with low dislocation density observed in the center of shear band result from recrystallization during dynamic deformation.

Electromechanical influence of crack velocity at bifurcation for poled ferroelectric materials

The piezoelastodynamic field equations are solved to determine the crack velocity at bifurcation for poled ferroelectric materials where the applied electrical field and mechanical stress can be varied. The underlying physical mechanism, however, may not correspond to that assumed in the analytical model. Bifurcation has been related to the occurrence of a pair of maximum circumferential stress oriented symmetrically about the moving crack path. The velocity at which this behavior prevails has been referred to as the limiting crack speed. Unlike the classical approach, bifurcation will be identified with finite distances ahead of a moving crack. Nucleation of microcracks can thus be modelled in a single formulation. This can be accomplished by using the energy density function where fracture initiation is identified with dominance of dilatation in relation to distortion. Poled ferroelectric materials are selected for this study because the microstructure effects for this class of materials can be readily reflected by the elastic, piezoelectic and dielectric permittivity constants at the macroscopic scale. Existing test data could also shed light on the trend of the analytical predictions. Numerical results are thus computed for PZT-4 and compared with those for PZT-6B in an effort to show whether the branching behavior would be affected by the difference in the material microstructures. A range of crack bifurcation speed upsilon(b) is found for different r/a and E/sigma ratios. Here, r and a stand for the radial distance and half crack length, respectively, while E and a for the electric field and mechanical stress. For PZT-6B with upsilon(b) in the range 100-1700 m/s, the bifurcation angles varied from +/-6degrees to +/-39degrees. This corresponds to E/sigma of -0.072 to 0.024 V m/N. At the same distance r/a = 0.1, PZT-4 gives upsilon(b) values of 1100-2100 m/s; bifurcation angles of +/-15degrees to +/-49degrees; and E/sigma of -0.056 to 0.059 V m/N. In general, the bifurcation angles +/-theta(0) are found to decrease with decreasing crack velocity as the distance r/a is increased. Relatively speaking, the speed upsilon(b) and angles +/-theta(0) for PZT-4 are much greater than those for PZT-6B. This may be attributed to the high electromechanical coupling effect of PZT-4. Using upsilon(b)(0) as a base reference, an equality relation upsilon(b)(-) < upsilon(b)(0) < upsilon(b)(+) can be established. The superscripts -, 0 and + refer, respectively, to negative, zero and positive electric field. This is reminiscent of the enhancement and retardation of crack growth behavior due to change in poling direction. Bifurcation characteristics are found to be somewhat erratic when r/a approaches the range 10(-2)-10(-1) where the kinetic energy densities would fluctuate and then rise as the distance from the moving crack is increased. This is an artifact introduced by the far away condition of non-vanishing particle velocity. A finite kinetic energy density prevails at infinity unless it is made to vanish in the boundary value problem. Future works are recommended to further clarify the physical mechanism(s) associated with bifurcation by means of analysis and experiment. Damage at the microscopic level needs to be addressed since it has been known to affect the macrocrack speeds and bifurcation characteristics. (C) 2002 Published by Elsevier Science Ltd.

A thermal insulation method for a piezoelectric transducer

This study deals with the sources of signal distortion of a piezoelectric transducer heated by measured gas flow. These signal distortions originate from both unloading of preload on a piezocrystal because of expansion of a diaphragm in the test apparatus and the pyroelectric effect of a heated piezoelectric crystal. A plastic film on the diaphragm of the transducer can effectively insulate the diaphragm and the piezocrystal within transducer from heating by gas flow, eliminating the sources of distortion. A method for evaluating the thickness of the film is proposed.

On the formation of well-aligned ZnO nanowall networks by catalyst-free thermal evaporation method

Two-dimensional ZnO nanowall networks were grown on ZnO-coated silicon by thermal evaporation at low temperature without catalysts or additives. All of the results from scanning electronic spectroscope, X-ray diffraction and Raman scattering confirmed that the ZnO nanowalls were vertically aligned and c-axis oriented. The room-temperature photoluminescence spectra showed a dominated UV peak at 378 nm, and a much suppressed orange emission centered at similar to 590 nm. This demonstrates fairly good crystal quality and optical properties of the product. A possible three-step, zinc vapor-controlled process was proposed to explain the growth of well-aligned ZnO nanowall networks. The pre-coated ZnO template layer plays a key role during the synthesis process, which guides the growth direction of the synthesized products. (C) 2007 Elsevier B.V. All rights reserved.

Suppressing chaos and transient in parameter perturbed systems

The systems with some system parameters perturbed are investigated. These systems might exist in nature or be obtained by perturbation or truncation theory. Chaos might be suppressed or induced. Some of these dynamical systems exhibit extraordinary long transients, which makes the temporal structure seem sensitively dependent on initial conditions in finite observation time interval.

Free surface vibration in oscillatory convection of half floating zone

Projecting an orthographical grating mask (20pl/mm) on the surface of a small liquid bridge and receiving the reflected distortion image, one can calculate out reversely the shape of free surface of a liquid bridge. In this way we measured the surface shape of a small floating zone and the two-dimensional deformation of its vibration. The mechanism of thermocapillary oscillatory convection and the three-dimensional variation of the free surface are revealed experimentally. The principle for space experiment has been studied in our laboratory.

Microstructures of explosively consolidated rapidly solidified aluminum and Al-Li alloy powders

The microstructures and the characteristics of water-atomized, nitrogen gas-atomized Al powders and ultrasonic argon gas-atomized Al-Li alloy powder were investigated by means of metallography, SEM, Auger electron spectroscopy and X-ray diffraction techniques. Rapidly solidified powders were explosively consolidated into different sized cylinders under various explosive parameters. The explosively consolidated compacts have been tested and analysed for density microhardness, retention of rapidly solidified microstructures, interparticle bonding, fractography and lattice distortion. It is shown that the explosive consolidation technique is an effective method for compacting rapidly solidified powders. The characteristics of surface layers play a very important role in determining the effectiveness of the joints sintered, and the Al-Li alloy explosive compacts present an abnormal softening appearance compared to the original powder.

The interaction of two pairs of solitary waves in a two-fluid system

This paper deals with the interaction of solitary waves in a two-fluid system which consistsof two superimposed incompressible inviscid fluids with a free surface and a horizontal rigidbottom. Under the assumption of shallow water wave, we first derive the basic equationssuitable for the model considered, a generalized form of the Boussinesq equations, then usingthe PLK method and the reductive perturbation method, obtain the second-order approximatesolution for the head-on collision between two pairs of interface and surface solitary waves,and give their maximum amplitudes during the collision and the nonuniform phase shiftsafter the collision which lead to the distortion of the wave profiles.

Analysis of the legislative framework in the Brazilian policymaking process

Analisa os aspectos da estrutura política brasileira que contribuem para falhas nos processos decisórios e ineficácia nos resultados finais de políticas de governo, com ênfase nos problemas institucionais do poder legislativo. Aborda os seguintes tópicos: fragmentação do sistema partidário, infidelidade partidária, modelo de federalismo, preenchimento de cargos públicos, larga utilização de medidas provisórias, disfunções do processo legislativo.

Fatores responsáveis pelo desequilíbrio na proporcionalidade na Câmara Federal

Analisa propostas apresentadas para mudanças no sistema de representatividade dos Estados e Distrito Federal na Câmara dos Deputados. O desequilíbrio está relacionado aos votos e cadeiras obtidos pelos partidos nas eleições e a distorção entre a população de determinadas unidades federativas e as cadeiras destinadas aos deputados. Esse desequilíbrio gera consequências no parlamento e contradiz o princípio de um Estado democrático de direito apresente o mesmo valor do voto para todo cidadão.

激光淬火基体对镀铬层抵抗接触变形的影响

提出先激光离散淬火预处理基体后再镀铬的复合工艺,利用划痕仪沿垂直激光扫描方向对铬层表面进行接触载荷模拟实验.结果表明:激光淬火基体能够提高镀铬层抵抗接触变形能力.利用基体化学腐蚀法制备自由铬层和纳米硬度仪对初始镀铬层力学性质进行分析表明:激光淬火基体不但通过提高基体的硬度增强了电镀铬层抵抗接触变形能力,而且也提高了铬层自身的抵抗接触变形能力.

New signal processing algorithms for automated external defibrillators

[ES]La fibrilación ventricular (VF) es el primer ritmo registrado en el 40\,\% de las muertes súbitas por paro cardiorrespiratorio extrahospitalario (PCRE). El único tratamiento eficaz para la FV es la desfibrilación mediante una descarga eléctrica. Fuera del hospital, la descarga se administra mediante un desfibrilador externo automático (DEA), que previamente analiza el electrocardiograma (ECG) del paciente y comprueba si presenta un ritmo desfibrilable. La supervivencia en un caso de PCRE depende fundamentalmente de dos factores: la desfibrilación temprana y la resucitación cardiopulmonar (RCP) temprana, que prolonga la FV y por lo tanto la oportunidad de desfibrilación. Para un correcto análisis del ritmo cardiaco es necesario interrumpir la RCP, ya que, debido a las compresiones torácicas, la RCP introduce artefactos en el ECG. Desafortunadamente, la interrupción de la RCP afecta negativamente al éxito en la desfibrilación. En 2003 se aprobó el uso del DEA en pacientes entre 1 y 8 años. Los DEA, que originalmente se diseñaron para pacientes adultos, deben discriminar de forma precisa las arritmias pediátricas para que su uso en niños sea seguro. Varios DEAs se han adaptado para uso pediátrico, bien demostrando la precisión de los algoritmos para adultos con arritmias pediátricas, o bien mediante algoritmos específicos para arritmias pediátricas. Esta tesis presenta un nuevo algoritmo DEA diseñado conjuntamente para pacientes adultos y pediátricos. El algoritmo se ha probado exhaustivamente en bases de datos acordes a los requisitos de la American Heart Association (AHA), y en registros de resucitación con y sin artefacto RCP. El trabajo comenzó con una larga fase experimental en la que se recopilaron y clasificaron retrospectivamente un total de 1090 ritmos pediátricos. Además, se revisó una base de arritmias de adultos y se añadieron 928 nuevos ritmos de adultos. La base de datos final contiene 2782 registros, 1270 se usaron para diseñar el algoritmo y 1512 para validarlo. A continuación, se diseñó un nuevo algoritmo DEA compuesto de cuatro subalgoritmos. Estos subalgoritmos están basados en un conjunto de nuevos parámetros para la detección de arritmias, calculados en diversos dominios de la señal, como el tiempo, la frecuencia, la pendiente o la función de autocorrelación. El algoritmo cumple las exigencias de la AHA para la detección de ritmos desfibrilables y no-desfibrilables tanto en pacientes adultos como en pediátricos. El trabajo concluyó con el análisis del comportamiento del algoritmo con episodios reales de resucitación. En los ritmos que no contenían artefacto RCP se cumplieron las exigencias de la AHA. Posteriormente, se estudió la precisión del algoritmo durante las compresiones torácicas, antes y después de filtrar el artefacto RCP. Para suprimir el artefacto se utilizó un nuevo método desarrollado a lo largo de la tesis. Los ritmos desfibrilables se detectaron de forma precisa tras el filtrado, los no-desfibrilables sin embargo no.

GmcA Is a Putative Glucose-Methanol-Choline Oxidoreductase Required for the Induction of Asexual Development in Aspergillus nidulans

18 p.

A method for estimating the rate of shedding of tags from yellowfin tuna

ENGLISH: The present paper describes a new method for estimating the shedding rate of tags. The method utilizes not only data on tagging and recovery of fish marked with two tags but also data from those marked with one. One important advantage of the new technique is that the estimates of the shedding rates are free from distortion caused by variations in fishing intensity during the total recovery period. The idea of this method appears to be implicit in a short note by Gulland (1963). This technique has been applied to the data obtained by the Inter-American Tropical Tuna Commission in a tagging cruise off the west coast of southern Baja California, during June 1963, at which time both single and double-tagged yellowfin tuna were released. Details of the tagging procedure and equipment have been described by Fink (1965b). The results presented in the present paper are for yellowfin tuna tagged with dart tags. Estimates of shedding should be made separately for each species investigated and also for each type of tag used, since these rates may be variable and often unexpectedly high (Springer and McErlean 1961, Chadwick 1963). SPANISH: El presente estudio describe un nuevo método para estimar las tasas del desprendimiento de marcas. El método emplea no solamente los datos sobre la marcación y recobro de peces marcados con dos marcas, pero también datos de los peces marcados con una marca. Una ventaja importante de la nueva técnica, es que las estimaciones de las tasas de desprendimiento son libres de alteración, causada por las variaciones en la intensidad de pesca durante el período total de recobro. La idea de este método parece ser implícita en un breve apunte por Gulland (1963). Esta técnica se ha aplicado a los datos obtenidos por la Comisión Interamericana del Atún Tropical, en un crucero de marcación efectuado frente a la costa occidental al sur de Baja California, en junio de 1963, tiempo en el cual fueron liberados atunes aleta amarilla marcados tanto con una como con dos marcas. Los detalles del procedimiento de la marcación y del equipo usado han sido descritos por Fink (1965b). Los resultados presentados en este estudio, pertenecen al atún aleta amarilla marcado con marcas de dardo. Las estimaciones del desprendimiento deben efectuarse separadamente para cada especie que ha sido investigada y también para cada tipo de marca usado, ya que estas tasas pueden ser vaiables, y a menudo inesperadamente altas (Springer y McErlean 1961, Chadwick 1963). (PDF contains 20 pages.)