Reaktive Polymere zur funktionellen Oberflächenbeschichtung

Ziel dieser Arbeit war die gezielte Modifizierung von Oberflächen mittels multifunktioneller Polymere, die ausgehend von Aktivesterpolymeren durch polymeranaloge Reaktionen unter milden Bedingungen hergestellt werden konnten. Dazu wurden die neuartigen Akivestermonomere Pentafluorphenylacrylat PFA und Pentafluorphenylmethacrylat PFMA hergestellt und polymerisiert. PFMA konnte unter RAFT-Bedingungen mittels Cumyldithiobenzoat bzw. 4-Cyano-4-((thiobenzoyl)sulfanyl)pentansäure kontrolliert polymerisiert werden. Durch den RAFT-Prozess wurden weiterhin reaktive Blockcopolymere aus PFMA und Methylmethacrylat, N Acryloylmorpholin bzw. N,N Diethylacrylamid synthetisiert. Zur Herstellung alpha, omega-endfunktionalisierter Polymere wurde PFA mit Dithiobenzoesäure-(4-dodecylbenzyl)ester polymerisiert und durch anschließende polymeranaloge Reaktionen zu thermoschaltbaren Polymeren mit unterschiedlichem LCST-Verhalten umgesetzt, die den Aufbau polymerunterstützter Lipiddoppelschichten ermöglichen. Ausgehend von poly(PFA) wurden oberflächenaktiven multifunktionellen Polymeren hergestellt und zur Oberflächenmodifizierung von anorganischen TiO2 Nanopartikeln, TiO2-Nanodrähten und MoS2-Nanopartikeln eingesetzt. Es konnten so lösliche fluoreszierende TiO2-Nanopartikel sowohl durch in situ- als auch post-Funktionalisierung hergestellt werden. Zudem konnte durch Verwendung eines multifunktionellen Polymers mit NTA-Einheiten das Enzym Silicatein auf TiO2-Nanodrähten immobilisert werden, das durch Biokristallisation Aggregate aus TiO2-Nanodrähten und Goldnanopartikeln erzeugte.

Ossidazione selettiva del 5-idrossimetilfurfurale con catalizzatori Au/Cu supportati su CeO2

I combustibili fossili forniscono oltre il 75% dell’energia mondiale. La crescente richiesta di energie non rinnovabili registrata nel XX secolo ne ha causato il progressivo esaurimento, nonché un aumento continuo del prezzo e dell’impatto ambientale, dato il significativo aumento delle emissioni di CO2 nell’atmosfera. Questi sono i principali motivi che hanno indotto la ricerca ad orientarsi verso lo studio di fonti di energie e prodotti chimici rinnovabili per ridurre il surriscaldamento del globo. L’interesse per tale sfruttamento è particolarmente vivo, in quanto le molecole ottenute risultano già funzionalizzate e questo può portare alla sintesi di prodotti chimici attraverso un limitato numero di stadi, con conseguente riduzione di sottoprodotti. Dalle biomasse si ottengono prodotti con un elevato valore aggiunto, in quanto risultano biodegradabili, biocompatibili e appetibili sul mercato come biologici e naturali, ottenuti a monte da processi catalitici di lavorazione più semplici. Tra le varie molecole di base ottenibili dalle biomasse va annoverato il 5-idrossimetilfurfurale (HMF), un importante composto derivato dalla disidratazione degli zuccheri e dal quale, attraverso un’ossidazione selettiva, si può ottenere l’acido 2,5-furandicarbossilico (FDCA), che può essere considerato un sostituto dell’acido tereftalico per la produzione del polietilentereftalato (PET). L’ossidazione selettiva avviene principalmente mediante catalisi eterogenea, utilizzando catalizzatori a base di oro. Lo scopo di questo lavoro di tesi è stato, quindi, lo studio di reattività e stabilità di catalizzatori utilizzati nella reazione di ossidazione dell’HMF a FDCA. Nella prima parte del lavoro sono stati preparati tali catalizzatori mediante sintesi di sospensioni metalliche nanoparticellari Au-Cu a diverso rapporto molare e loro successiva impregnazione su ossidi di supporto quali CeO2 e TiO2. I sistemi così ottenuti sono poi stati calcinati in aria statica a tre diverse temperature: 200°C, 300°C e 400°C. Il lavoro portato avanti ha avuto come obiettivi principali: • caratterizzazione dei catalizzatori ottenuti tramite analisi BET, XRD, TEM, TPR e analisi termiche TGA/DSC, al fine di effettuare un confronto tra le varie caratterizzazioni in funzione del contenuto di Cu in fase attiva ed in funzione dell’entità del trattamento termico. • studio dell’attività catalitica e stabilità dei catalizzatori preparati nell’ossidazione selettiva in fase liquida del 5-drossimetilfurfurale ad acido 2,5-furandicarbossilico.

Untersuchungen zur Löslichkeit von Kobalt und Eisen in TiO 2-Bulk sowie in TiO 2-Nanoproben und deren Einfluss auf die magnetischen Eigenschaften

Co- und Fe-dotierte Rutil- und Anatas-Bulkproben wurden über einen Sol-Gel Prozess und anschließende thermische Behandlung dargestellt und auf ihre Zugehörigkeit zu der Gruppe der verdünnten magnetischen Oxide untersucht. Die Untersuchungen der dotierten Rutil-Proben mittels Röntgenbeugung, Elektronenmikroskopie und magnetischen Methoden zeigen, dass die Löslichkeit von Co und Fe in der TiO2-Modifikation Rutil sehr gering ist. Oberhalb von 1at% Co bzw. Fe wird neben Rutil die Bildung der Oxide CoTiO3 bzw. Fe2TiO5 beobachtet. Weitere thermische Behandlung im Argon-H2-Strom führte aufgrund der Bildung von metallischem Co bzw. Fe zu einem ferromagnetischen Verhalten. Die TiO2-Modifikation Anatas besitzt eine höhere Löslichkeit, so dass erst oberhalb von 4at% Co bzw. 10at% Fe die Phasen Co3O4 bzw. FeTiO3 neben Anatas auftreten. Entsprechende Proben zeigen ein paramagnetisches Verhalten. Oberhalb der Löslichkeitsgrenze führt die Reduktion im Argon-H2-Strom zu einem ferromagnetischen Verhalten, welches auf metallisches Co bzw. Fe zurückzuführen ist. Analog zu den Bulkproben wurden Co- und Fe-dotierte TiO2-Nanodrähte hergestellt. Das magnetische Verhalten der Fe-dotierten TiO2-Nanodrähte entspricht dem der Fe-dotierten Anatas-Bulkproben. Dagegen führt die Co-Dotierung nicht zu einem Einbau in die TiO2-Nanodrähte, sondern zur Bildung von CoOx-Nanopartikeln. Die entsprechenden Proben zeigen ein schwach ferromagnetisches Verhalten. Dies ist jedoch nicht auf eine ferromagnetische Dotierung der TiO2-Nanodrähte zurückzuführen, sondern auf nicht kompensierte Momente an den Oberflächen der als Verunreinigungen auftretenden CoOx-Nanopartikel. Zusammenfassend wird festgestellt, dass die Löslichkeit von Co und Fe in TiO2 für die Ausbildung eines ferromagnetischen Verhaltens zu gering ist. Der beobachtete Ferromagnetismus lässt sich eindeutig auf magnetische Verunreinigungen zurückführen. Somit können die dotierten TiO2 Proben nicht den verdünnten magnetischen Oxiden zugeordnet werden.

Petrogenesis of dunite, wehrlite and websterite xenoliths from Kimberley, South Africa: Origin as mantle peridotites of cumulates

Dunite, wehrlite and websterite xenoliths occur amongst a large abundance of mantle xenoliths in kimberlites of the Kimberley cluster in South Africa. Up to know they have mostly been neglected. On the basis of texture, major and trace elements, oxygen isotopes as well as Re-Os isotope characteristics, they can be subdivided into two groups. A coarse-grained mantle peridotite group, comprising dunite, wehrlite and websterite xenoliths, that are similar to fertile peridotites and represent upper mantle assemblages that are differently influenced by mantle metasomatism. And a cumulate group, containing fine-grained Fe-rich dunite xenoliths that represent cumulates of flood basalt magmatism related to ~183 Ma Karoo and ~2.7 Ga Ventersdorp events in southern Africa. Dunite, wehrlite and websterite xenoliths have preserved a complex history of melt depletion and metasomatic re-enrichment events, which gives information about the different re-enrichment stages of the subcratonic lithospheric mantle and the spatial differences within the Kaapvaal craton upper mantle. Websterite xenoliths comprise orthopyroxene (40-85 Vol. %), clinopyroxene (5-42 Vol. %), garnet (4-10 Vol. %) and subordinately olivine, while dunite and wehrlite xenoliths contain predominantly olivine (65-100 Vol %) and subordinately orthopyroxene, clinopyroxene and garnet. High melt depletion and a dunitic to harzburgitic protolith composition are reflected by high forsterite (Fo90-92) and high olivine NiO contents (2800-5000 ppm) and high orthopyroxene Mg# (Mg/(Mg+Fe)) of 0.91-0.93. Re-depletion ages of predominantly 2.9 Ga reflect a minimum age of melt depletion. Melt depletion ceased in conjunction with collision of the Kimberley block with the Witwatersrand block ~2.9 Ga ago. Subduction related re-fertilisation of the previously depleted mantle xenoliths is documented by i) amoeboid textured orthopyroxene, clinopyroxene and garnet, which crystallized in schlieren along olivine grain boundaries, ii) high whole-rock SiO2, Al2O3, CaO, TiO2, FeO contents, iii) low oxygen isotope ratios in clinopyroxene and garnet of 4.8-5.4 ‰ and 4.7-5.3 ‰, respectively and iv) trace element compositions of wehrlitic clinopyroxene and garnet in equilibrium with high-pressure partial melts of eclogite. Trace element disequilibrium of orthopyroxene with clinopyroxene and garnet indicates a separate origin for orthopyroxene, on one side as primary mantle orthopyroxene in dunite and wehrlite xenoliths and on the other side as reaction product with Si-rich melts produced by partial melting of eclogite. This reaction triggered replacement of olivine by orthopyroxene in the surrounding mantle and produced the typical Si-rich composition of Kaapvaal mantle peridotites. Partial melting of eclogite at higher temperatures produced a second metasomatic melt with lower SiO2, but higher Al2O3, CaO, FeO, Ti, Zr, Hf and a low oxygen isotope ratio. This melt triggered clinopyroxene and locally garnet and rutile crystallization in percolation veins, replacing olivine and orthopyroxene in the Kaapvaal upper mantle. Additionally, websterite xenoliths have experienced late stage cryptic metasomatism by the host kimberlite melt, changing the trace element composition of clinopyroxene, orthopyroxene and garnet to different extent. Hence websterite and most fertile lherzolite xenoliths have experienced three metasomatic events: i) reaction with high-Si melt, ii) percolation of subduction related silica melt with lower SiO2 content and iii) cryptic metasomatism by kimberlite. In contrast, dunite and wehrlite xenoliths have only experienced the second metasomatic event. They represent mantle lithologies further away from metasomatising agents. The Fe-rich dunites comprise olivine neoblasts with subordinate olivine porphyroclasts and parallel-orientated needles of ilmenite, which may enclose spinel. The lower forsterite and NiO contents of olivine in Fe-rich dunites compared to mantle peridotite xenoliths (Fo87-89 vs. Fo93-95 and 1300-2800ppm vs. 2200-3900 ppm, respectively), rules out a restitic origin. Cr-rich spinels are remnants of the original cumulate mineralogy that survived a late stage metasomatic overprint related to the production of the host kimberlite, producing ilmenite and phlogopite in some samples. Olivine porphyroclasts and neoblasts have different trace element compositions, the latter having high Ti, V, Cr and Ni and low Zn, Zr and Nb contents, indicating contrasting origins for neoblasts and porphyroclasts. The dunites have high 187Os/188Os ratios (0.11-0.15) indicating young (Phanerozoic) model ages for most samples, whereas three samples show isotopic mixtures between Phanerozoic neoblasts and ancient porphyroclastic material. Most Fe-rich dunite xenoliths can be interpreted as cumulates of fractional crystallization of Karoo magmatism, whereas the porphyroclasts are interpreted to be remnants from the much earlier Archaean Ventersdorp magmatism.

Valutazione del Fattore di Effetto nella metodologia LCA: test sperimentali di tossicità indotti da nanoparticelle di Diossido di Titanio sull’alga Pseudokirchneriella Subcapitata

La nanotecnologia è una scienza innovativa che sviluppa e utilizza materiali di dimensioni nanometriche (< 100 nm). Lo sviluppo e il mercato delle nanoparticelle in merito alle loro interessanti proprietà chimico‐fisiche, é accompagnato da una scarsa conoscenza relativa al destino finale e agli effetti che questi nano materiali provocano nell’ ambiente [Handy et al., 2008]. La metodologia LCA (Life Cycle Assessment – Valutazione del Ciclo di Vita) è riconosciuta come lo strumento ideale per valutare e gestire gli impatti ambientali indotti dalle ENPs, nonostante non sia ancora possibile definire, in maniera precisa, un Fattore di Caratterizzazione CF per questa categoria di sostanze. Il lavoro di questa tesi ha l’obbiettivo di stimare il Fattore di Effetto EF per nanoparticelle di Diossido di Titanio (n‐TiO2) e quindi contribuire al calcolo del CF; seguendo il modello di caratterizzazione USEtox, l’EF viene calcolato sulla base dei valori di EC50 o LC50 relativi agli organismi appartenenti ai tre livelli trofici di un ecosistema acquatico (alghe, crostacei, pesci) e assume valore pari a 49,11 PAF m3/Kg. I valori tossicologici utilizzati per il calcolo del Fattore di Effetto derivano sia da un’accurata ricerca bibliografica sia dai risultati ottenuti dai saggi d’inibizione condotti con n‐TiO2 sulla specie algale Pseudokirchneriella Subcapitata. La lettura dei saggi è stata svolta applicando tre differenti metodi quali la conta cellulare al microscopio ottico (media geometrica EC50: 2,09 mg/L, (I.C.95% 1,45‐ 2,99)), l’assorbanza allo spettrofotometro (strumento non adatto alla lettura di test condotti con ENPs) e l’intensità di fluorescenza allo spettrofluorimetro (media geometrica EC50: 3,67 mg/L (I.C.95% 2,16‐6,24)), in modo tale da confrontare i risultati e valutare quale sia lo strumento più consono allo studio di saggi condotti con n‐TiO2. Nonostante la grande variabilità dei valori tossicologici e la scarsa conoscenza sui meccanismi di tossicità delle ENPs sulle specie algali, il lavoro sperimentale e la ricerca bibliografica condotta, hanno permesso di individuare alcune proprietà chimico‐fisiche delle nanoparticelle di Diossido di Titanio che sembrano essere rilevanti per la loro tossicità come la fase cristallina, le dimensioni e la foto attivazione [Vevers et al., 2008; Reeves et al., 2007]. Il lavoro sperimentale ha inoltre permesso di ampliare l’insieme di valori di EC50 finora disponibile in letteratura e di affiancare un progetto di ricerca dottorale utilizzando il Fattore di Effetto per n‐ TiO2 nel calcolo del Fattore di Caratterizzazione.

Thin nanostructured crystalline TiO 2 films and their applications in solar cells

Research on thin nanostructured crystalline TiO2 films has attracted considerable interests because of their intriguing physical properties and potential applications in photovoltaics. Nanostructured TiO2 film plays an important role in the TiO2 based dye-sensitized solar cells because they act as a substrate for the adsorption of dye molecules and a matrix for the transportation of electrons as well. Thus they can influence the solar cell performance significantly. Consequently, the control of the morphology including the shape, size and size distribution of the TiO2 nanostructures is critical to tune and optimize the performance of the solar cells. To control the TiO2 morphology, a strategy using amphiphilic block copolymer as templating agent coupled with sol-gel chemistry has been applied. Especially, a good-poor solvent pair induced phase separation process has been developed to guide the microphase separation behavior of the block copolymers. The amphiphilic block copolymers used include polystyrene-block-poly (ethylene oxide) (PS-b-PEO), poly (methyl methacrylate)-block-poly (ethylene oxide) (PMMA-b-PEO), and poly (ethylene oxide)-block-polystyrene-block-poly (ethylene oxide) (PEO-b-PS-b-PEO). The block copolymer undergoes a good-poor-solvent pair induced phase separation in a mixed solution of 1, 4-dioxane or N, N’-dimethyl formamide (DMF), concentrated hydrochloric acid (HCl) and Titanium tetraisopropoxide (TTIP). Specifically, in the system of PS-b-PEO, a morphology phase diagram of the inorganic-copolymer composite films was mapped by adjusting the weight fractions among 1, 4-dioxane, HCl, and TTIP in solution. The amorphous TiO2 within the titania-block copolymer composite films was crystallized by calcination at temperatures above 400C, where the organic block copolymer was simultaneously burned away. This strategy is further extended to other amphiphilic block copolymers of PMMA-b-PEO and PEO-b-PS-b-PEO, where the morphology of TiO2 films can also be controlled. The local and long range structures of the titania films were investigated by the combination of imaging techniques (AFM, SEM) and x-ray scattering techniques (x-ray reflectivity and grazing incidence small-angle x-ray scattering). Based on the knowledge of the morphology control, the crystalline TiO2 nanostructured films with different morphologies were introduced into solid state dye-sensitized solar cells. It has been found that all of the morphologies help to improve the performance of the solar cells. Especially, clustered nanoparticles, worm-like structures, foam-like structures, large collapsed nanovesicles show more pronounced performance improvement than other morphologies such as nanowires, flakes, and nanogranulars.

Outdoor bronze conservation: assessment of protective treatments by accelerated aging and of treatment removal procedures by laser cleaning

Outdoor bronzes exposed to the environment form naturally a layer called patina, which may be able to protect the metallic substrate. However, since the last century, with the appearance of acid rains, a strong change in the nature and properties of the copper based patinas occurred [1]. Studies and general observations have established that bronze corrosion patinas created by acid rain are not only disfiguring in terms of loss of detail and homogeneity, but are also unstable [2]. The unstable patina is partially leached away by rainwater. This leaching is represented by green streaking on bronze monuments [3]. Because of the instability of the patina, conservation techniques are usually required. On a bronze object exposed to the outdoor environment, there are different actions of the rainfall and other atmospheric agents as a function of the monument shape. In fact, we recognize sheltered and unsheltered areas as regards exposure to rainwater [4]. As a consequence of these different actions, two main patina types are formed on monuments exposed to the outdoor environment. These patinas have different electrochemical, morphological and compositional characteristics [1]. In the case of sheltered areas, the patina contains mainly copper products, stratified above a layer strongly enriched in insoluble Sn oxides, located at the interface with the uncorroded metal. Moreover, different colors of the patina result from the exposure geometry. The surface color may be pale green for unsheltered areas, and green and mat black for sheltered areas [4]. Thus, in real outdoor bronze monuments, the corrosion behavior is strongly influenced by the exposure geometry. This must be taken into account when designing conservation procedures, since the patina is in most cases the support on which corrosion inhibitors are applied. Presently, for protecting outdoor bronzes against atmospheric corrosion, inhibitors and protective treatments are used. BTA and its derivatives, which are the most common inhibitors used for copper and its alloy, were found to be toxic for the environment and human health [5, 6]. Moreover, it has been demonstrated that BTA is efficient when applied on bare copper but not as efficient when applied on bare bronze [7]. Thus it was necessary to find alternative compounds. Silane-based inhibitors (already successfully tested on copper and other metallic substrates [8]), were taken into consideration as a non-toxic, environmentally friendly alternative to BTA derivatives for bronze protection. The purpose of this thesis was based on the assessment of the efficiency of a selected compound, to protect the bronze against corrosion, which is the 3-mercapto-propyl-trimethoxy-silane (PropS-SH). It was selected thanks to the collaboration with the Corrosion Studies Centre “Aldo Daccò” at the Università di Ferrara. Since previous studies [9, 10, 11] demonstrated that the addition of nanoparticles to silane-based inhibitors leads to an increase of the protective efficiency, we also wanted to evaluate the influence of the addition of CeO2, La2O3, TiO2 nanoparticles on the protective efficiency of 3-mercapto-propyl-trimethoxy-silane, applied on pre-patinated bronze surfaces. This study is the first section of the thesis. Since restorers have to work on patinated bronzes and not on bare metal (except for contemporary art), it is important to be able to recreate the patina, under laboratory conditions, either in sheltered or unsheltered conditions to test the coating and to obtain reliable results. Therefore, at the University of Bologna, different devices have been designed to simulate the real outdoor conditions and to create a patina which is representative of real application conditions of inhibitor or protective treatments. In particular, accelerated ageing devices by wet & dry (simulating the action of stagnant rain in sheltered areas [12]) and by dropping (simulating the leaching action of the rain in unsheltered areas [1]) tests were used. In the present work, we used the dropping test as a method to produce pre-patinated bronze surfaces for the application of a candidate inhibitor as well as for evaluating its protective efficiency on aged bronze (unsheltered areas). In this thesis, gilded bronzes were also studied. When they are exposed to the outside environment, a corrosion phenomenon appears which is due to the electrochemical couple gold/copper where copper is the anode. In the presence of an electrolyte, this phenomenon results in the formation of corrosion products than will cause a blistering of the gold (or a break-up and loss of the film in some cases). Moreover, because of the diffusion of the copper salts to the surface, aggregates and a greenish film will be formed on the surface of the sample [13]. By coating gilded samples with PropS-SH and PropS-SH containing nano-particles and carrying out accelerated ageing by the dropping test, a discussion is possible on the effectiveness of this coating, either with nano-particles or not, against the corrosion process. This part is the section 2 of this thesis. Finally, a discussion about laser treatment aiming at the assessment of reversibility/re-applicability of the PropS-SH coating can be found in section 3 of this thesis. Because the protective layer loses its efficiency with time, it is necessary to find a way of removing the silane layer, before applying a new one on the “bare” patina. One request is to minimize the damages that a laser treatment would create on the patina. Therefore, different laser fluences (energy/surface) were applied on the sample surface during the treatment process in order to find the best range of fluence. In particular, we made a characterization of surfaces before and after removal of PropS-SH (applied on a naturally patinated surface, and subsequently aged by natural exposure) with laser methods. The laser removal treatment was done by the CNR Institute of Applied Physics “Nello Carrara” of Sesto Fiorentino in Florence. In all the three sections of the thesis, a range of non-destructive spectroscopic methods (Scanning Electron Microscopy with Energy Dispersive Spectroscopy (SEM-EDS), μ-Raman spectroscopy, X-Ray diffractometry (XRD)) were used for characterizing the corroded surfaces. AAS (Atomic Absorption Spectroscopy) was used to analyze the ageing solutions from the dropping test in sections 1 and 2.

Crescita e analisi strutturale di film nanoparticellari di titania

Il lavoro di questa tesi è incentrato sulla crescita e lo studio delle proprietà strutturali di sistemi nanostrutturati di titanio e ossido di titanio, prodotti mediante la tecnica della condensazione in gas inerte. Lo studio è finalizzato in particolare ad ottenere un materiale idoneo per la produzione di idrogeno tramite la foto-elettrolisi. Nel primo capitolo viene descritto a livello teorico il processo di scissione dell’acqua all’interno di celle foto-elettrochimiche, in cui viene impiegato il TiO2 (titania) come foto-anodo. Nel secondo capitolo viene introdotta la tecnica di crescita, viene descritta la macchina utilizzata illustrandone vantaggi e limitazioni. Inoltre viene fornita una descrizione teorica del tipo di crescita che avviene all’interno della camera di evaporazione. Allo scopo di comprendere meglio questi processi, vengono riportati nel capitolo 3 alcuni studi, basati su principi primi, riguardanti la stabilità di fase e le trasformazioni di fase per i tre principali polimorfi del TiO2. Nel capitolo 4 sono illustrate le tecniche impiegate per l’indagine strutturale: diffrazione e assorbimento di raggi X con relativa analisi dati, microscopia elettronica a scansione. Prima di misurare l’attività fotocatalitica dei campioni di nanoparticelle di titania, è necessario condurre delle misure di fotocorrente in una cella foto-elettrochimica, i risultati di queste analisi di tipo funzionale sono presentati nel capitolo 5. Nel capitolo 6 sono riportate le conclusioni del lavoro di tesi.

Determinazione di radicali OH: sintesi di materiali per la modifica di elettrodi di platino e carbone vetroso

Questa tesi descrive lo sviluppo di un elettrodo modificato con un polimero isolante per la determinazione indiretta del radicale OH. I polimeri testati sono stati polifenolo, polipirrolo e polipirrolo sovraoossidato ed il primo è risultato quello con le migliori prestazioni. Il film di modificante è stato depositato per elettropolimerizzazione del fenolo in ambiente acido, su un elettrodo di carbone vetroso (GC) ed è risultato isolante e perfettamente adeso al GC, impedendo il trasferimento di carica alle più comuni sonde redox. L’attacco dei radicali OH, generati dalla reazione di Fenton o dalla fotolisi di H2O2, rimuove parzialmente il polimero dal GC, ripristinando parzialmente il comportamento conduttore dell’elettrodo. L’entità della degradazione del film polifenolico è stata valutata sfruttando la corrente relativa alla sonda redox Ru(NH3)63+, che rappresenta il segnale analitico per la determinazione del radicale OH. L’elettrodo è stato impiegato per stimare le prestazioni di foto catalizzatori a base di nanoparticelle di TiO2, ottenendo risultati correlati a quelli ricavati da un metodo HPLC. Inoltre esso è stato usato per sviluppare una nuova procedura per la determinazione della capacità di scavenging verso i radicali OH, che è stata applicata all’analisi di composti puri e campioni reali. I risultati erano confrontabili con quelli determinati con metodiche standardizzate, comunemente impiegate per la determinazione della capacità antiossidante. Inoltre è stato condotto uno studio riguardante la modifica di un elettrodo di platino con un idrossido misto a strati a base di cobalto e alluminio (LDH). In particolare si sono valutati gli effetti di diversi pretrattamenti del Pt sulle caratteristiche e prestazioni elettrocatalitiche del film di LDH nei confronti dell’ossidazione di anilina, fenolo e acido salicilico. Questi composti possono essere impiegati come molecole sonda per la determinazione del radicale OH e rivestono interesse da un punto di vista elettroanalitico perché portano facilmente alla passivazione della superficie di Pt.

New sensing platforms based on nanoscopic devices for probing protein-membrane interactions

A novel nanosized and addressable sensing platform based on membrane coated plasmonic particles for detection of protein adsorption using dark field scattering spectroscopy of single particles has been established. To this end, a detailed analysis of the deposition of gold nanorods on differently functionalized substrates is performed in relation to various factors (such as the pH, ionic strength, concentration of colloidal suspension, incubation time) in order to find the optimal conditions for obtaining a homogenous distribution of particles at the desired surface number density. The possibility of successfully draping lipid bilayers over the gold particles immobilized on glass substrates depends on the careful adjustment of parameters such as membrane curvature and adhesion properties and is demonstrated with complementary techniques such as phase imaging AFM, fluorescence microscopy (including FRAP) and single particle spectroscopy. The functionality and sensitivity of the proposed sensing platform is unequivocally certified by the resonance shifts of the plasmonic particles that were individually interrogated with single particle spectroscopy upon the adsorption of streptavidin to biotinylated lipid membranes. This new detection approach that employs particles as nanoscopic reporters for biomolecular interactions insures a highly localized sensitivity that offers the possibility to screen lateral inhomogeneities of native membranes. As an alternative to the 2D array of gold nanorods, short range ordered arrays of nanoholes in optically transparent gold films or regular arrays of truncated tetrahedron shaped particles are built by means of colloidal nanolithography on transparent substrates. Technical issues mainly related to the optimization of the mask deposition conditions are successfully addressed such that extended areas of homogenously nanostructured gold surfaces are achieved. Adsorption of the proteins annexin A1 and prothrombin on multicomponent lipid membranes as well as the hydrolytic activity of the phospholipase PLA2 were investigated with classical techniques such as AFM, ellipsometry and fluorescence microscopy. At first, the issues of lateral phase separation in membranes of various lipid compositions and the dependency of the domains configuration (sizes and shapes) on the membrane content are addressed. It is shown that the tendency for phase segregation of gel and fluid phase lipid mixtures is accentuated in the presence of divalent calcium ions for membranes containing anionic lipids as compared to neutral bilayers. Annexin A1 adsorbs preferentially and irreversibly on preformed phosphatidylserine (PS) enriched lipid domains but, dependent on the PS content of the bilayer, the protein itself may induce clustering of the anionic lipids into areas with high binding affinity. Corroborated evidence from AFM and fluorescence experiments confirm the hypothesis of a specifically increased hydrolytic activity of PLA2 on the highly curved regions of membranes due to a facilitated access of lipase to the cleavage sites of the lipids. The influence of the nanoscale gold surface topography on the adhesion of lipid vesicles is unambiguously demonstrated and this reveals, at least in part, an answer for the controversial question existent in the literature about the behavior of lipid vesicles interacting with bare gold substrates. The possibility of formation monolayers of lipid vesicles on chemically untreated gold substrates decorated with gold nanorods opens new perspectives for biosensing applications that involve the radiative decay engineering of the plasmonic particles.

Design, synthesis and Chemical-physical characterization of photocatalytic inorganic nanocrystals for technological applications

This work was based on the synthesis and characterization of innovative crystals for biomedical and technological applications. Different types of syntheses were developed in order to obtain crystals with high photocatalytic properties. A hydrothermal synthesis was also processed to correlate the chemical-physical characteristics with synthesis parameters obtaining synthesis of nanoparticles of titanium dioxide with different morphology, size and crystalline phase depending on the variation of the synthesis parameters. Also a synthesis in water at 80 °C temperature and low pressure was developed from which anatase containing a small percentage of brookite nanoparticles were obtained, presenting a high photocatalytic activity. These particles have been used to obtain the microcrystals formed by an inorganic core of hydroxyapatite surface covered by TiO2 nanoparticles. Micrometer material with higher photocatalytic has been produced. The same nanoparticles have been functionalized with resorcinol oxidized in order to increase the photocatalytic efficiency. Photodegradation test results have confirmed this increase. Finally, synthetic nanoparticles with a waterless synthesis using formic acid and octanol, through esterification "in situ" were synthesized. Nanoparticles superficially covered by carboxylic residues able to bind a wide range of molecules to obtain further photocatalytic properties were obtained.

New catalytic processes for the upgrading of furfural and 5-hydroxymethylfurfural to chemicals and fuels

The demand of energy, fuels and chemicals is increasing due to the strong growth of some countries in the developing world and the development of the world economy. Unfortunately, the general picture derived sparked an exponential increase in crude oil prices with a consequent increase of the chemical, by-products and energy, depleting the global market. Nowadays biomass are the most promising alternative to fossil fuels for the production of chemicals and fuels. In this work, the development of three different catalytic processes for the valorization of biomass-derived has been investigated. 5-hydroxymethylfurfural oxidation was studied under mild reaction condition using gold and gold/copper based catalysts synthetized from pre-formed nanoparticles and supported onto TiO2 and CeO2. The analysis conducted on catalysts showed the formation of alloys gold/copper and a strong synergistic effect between the two metals. For this reason the bimetallic catalysts supported on titania showed a higher catalytic activity respect to the monometallic catalysts. The process for the production of 2,5-bishydroxymethyl furan (BHMF) was also optimized by means the 5-hydroxymethylfurfural hydrogenation using the Shvo complex. Complete conversion of HMF was achieved working at 90 °C and 10 bar of hydrogen. The complex was found to be re-usable for at least three catalytic cycles without suffering any type of deactivation. Finally, the hydrogenation of furfural and HMF was carried out, developing the process of hydrogen transfer by using MgO as a catalyst and methanol as a hydrogen donor. Quantitative yields to alcohols have been achieved in a few hours working in mild condition: 160 °C and at autogenous pressure. The only by-products formed were light products such as CO, CO2 and CH4 (products derived from methanol transformation), easily separable from the reaction solution depressurizing the reactor.

Crescita di nanoparticelle in flusso di gas inerte

Lo scopo della seguente tesi è quello di illustrare la disposizione dei campioni di sistemi binari Mg Pd e di deposizioni singole di Ti, nell’abito di due progetti di ricerca, l’SSHS, Solide State Hydrogen Storage nell’ambito dell’Azione COST, e la produzione di titania (TiO2) per la fotocatalisi, sintetizzati in differenti reggimi di flusso di gas d’He, realizzando la crescita con il metodo IGC. Sono state illustrate le nuove proprietà e i metodi di formazione dei materiali nanostrutturati, per poi passare alla descrizione dell’apparato dove sono stati prodotti i campioni, con la conseguente spiegazione della progettazione del controllore di flusso dei sistemi di alimentazione e interfacciamento di quest’ultimo. Dopo un’accurata analisi al microscopio elettronico, `e stata descritta la morfologia dei campioni a due diversi reggimi di flusso di gas He, per i campioni di Mg Pd non sono state apprezzate differenze al variare del flusso, per il Ti, invece, si può notare una variazione morfologica legata alle dimensioni.

Effects of metal-induced oxidative stress on endothelial cells in vitro

Aseptic loosening of metal implants is mainly attributed to the formation of metal degradation products. These include particulate debris and corrosion products, such as metal ions (anodic half-reaction) and ROS (cathodic half-reaction). While numerous clinical studies describe various adverse effects of metal degradation products, detailed knowledge of metal-induced cellular reactions, which might be important for possible therapeutic intervention, is not comprehensive. Since endothelial cells are involved in inflammation and angiogenesis, two processes which are critical for wound healing and integration of metal implants, the effects of different metal alloys and their degradation products on these cells were investigated. Endothelial cells on Ti6Al4V alloy showed signs of oxidative stress, which was similar to the response of endothelial cells to cathodic partial reaction of corrosion induced directly on Ti6Al4V surfaces. Furthermore, oxidative stress on Ti6Al4V alloy reduced the pro-inflammatory stimulation of endothelial cells by TNF-α and LPS. Oxidative stress and other stress-related responses were observed in endothelial cells in contact with Co28Cr6Mo alloy. Importantly, these features could be reduced by coating Co28Cr6Mo with a TiO2 layer, thus favouring the use of such surface modification in the development of medical devices for orthopaedic surgery. The reaction of endothelial cells to Co28Cr6Mo alloy was partially similar to the effects exerted by Co2+, which is known to be released from metal implants. Co2+ also induced ROS formation and DNA damage in endothelial cells. This correlated with p53 and p21 up-regulation, indicating the possibility of cell cycle arrest. Since CoCl2 is used as an hypoxia-mimicking agent, HIF-1α-dependence of cellular responses to Co2+ was studied in comparison to anoxia-induced effects. Although important HIF-1α-dependent genes were identified, a more detailed analysis of microarray data will be required to provide additional information about the mechanisms of Co2+ action. All these reactions of endothelial cells to metal degradation products might play their role in the complex processes taking place in the body following metal device implantation. In the worst case this can lead to aseptic loosening of the implant and requirement for revision surgery. Knowledge of molecular mechanisms of metal-induced responses will hopefully provide the possibility to interfere with undesirable processes at the implant/tissue interface, thus extending the life-time of the implant and the overall success of metal implant applications.

Self assembled materials for solar cell application

In der vorliegenden Arbeit wurden Materialien und Aufbauten für Hybrid Solarzellen entwickelt und erforscht. rnDer Vergleich zweier bekannter Lochleitermaterialien für Solarzellen in einfachen Blend-Systemen brachte sowohl Einsicht zur unterschiedlichen Eignung der Materialien für optoelektronische Bauelemente als auch neue Erkenntnisse in Bereichen der Langzeitstabilität und Luftempfindlichkeit beider Materialien.rnWeiterhin wurde eine Methode entwickelt, um Hybrid Solarzelle auf möglichst unkomplizierte Weise aus kostengünstigen Materialien darzustellen. Die „Eintopf“-Synthese ermöglicht die unkomplizierte Darstellung eines funktionalen Hybridmaterials für die optoelektronische Anwendung. Mithilfe eines neu entwickelten amphiphilen Blockcopolymers, das als funktionelles Templat eingesetzt wurde, konnten mit einem TiO2-Precursor in einem Sol-Gel Ansatz verschiedene selbstorganisierte Morphologien des Hybridmaterials erhalten werden. Verschiedene Morphologien wurden auf ihre Eignung in Hybrid Solarzellen untersucht. Ob und warum die Morphologie des Hybridsystems die Effizienz der Solarzelle beeinflusst, konnte verdeutlicht werden. Mit der Weiterentwicklung der „Eintopf“-Synthese, durch den Austausch des TiO2-Precursors, konnte die Solarzelleneffizienz von 0.15 auf 0.4 % gesteigert werden. Weiterhin konnte die Übertragbarkeit des Systems durch den erfolgreichen Austausch des Halbleiters TiO¬2 mit ZnO bewiesen werden.rn