Dye-sensitized solar cells based on perylene derivatives

The oil price rises more and more, and the world energy consumption is projected to expand by 50 percent from 2005 to 2030. Nowadays intensive research is focused on the development of alternative energies. Among them, there are dye-sensitized nanocrystalline solar cells (DSSCs) “the third generation solar cells”. The latter have gained attention during the last decade and are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic. At present DSSCs with ruthenium based dyes exhibit highest efficiencies (ca 11%). The objective of the present work is to fabricate, characterize and improve the performance of DSSCs based on metal free dyes as sensitizers, especially on perylene derivatives. The work begins by a general introduction to the photovoltaics and dye-sensitized solar cells, such as the operating principles and the characteristics of the DSSCs. Chapter 2 and 3 discuss the state of the art of sensitizers used in DSSCs, present the compounds used as sensitizer in the present work and illustrate practical issues of experimental techniques and device preparation. A comparative study of electrolyte-DSSCs based on P1, P4, P7, P8, P9, and P10 are presented in chapter 4. Experimental results show that the dye structure plays a crucial role in the performance of the devices. The dye based on the spiro-concept (bipolar spiro compound) exhibited a higher efficiency than the non-spiro compounds. The presence of tert-butylpyridine as additive in the electrolyte was found to increase the open circuit voltage and simultaneously decrease the efficiency. The presence of lithium ions in the electrolyte increases both output current and the efficiency. The sensitivity of the dye to cations contained in the electrolyte was investigated in the chapter 5. FT-IR and UV-Vis were used to investigate the in-situ coordination of the cation to the adsorbed dye in the working devices. The open-circuit voltage was found to depend on the number of coordination sites in the dye. P1 with most coordination sites has shown the lowest potential drop, opposite to P7, which is less sensitive to cations in the working cells. A strategy to improve the dye adsorption onto the TiO2 surface, and thus the light harvesting efficiency of the photoanode by UV treatment, is presented in chapter 6. The treatment of the TiO2 film with UV light generates hydroxyl groups and renders the TiO2 surface more and more hydrophilic. The treated TiO2 surface reacts readily with the acid anhydride group of the dye that acts as an anchoring group and improves the dye adsorption. The short-circuit current density and the efficiency of the electrolyte-based dye cells was considerably improved by the UV treatment of the TiO2 film. Solid-state dye-sensitized solar cells (SSDs) based on spiro-MeOTAD (used as hole transport material) are studied in chapter 7. The efficiency of SSDs was globally found to be lower than that of electrolyte-based solar cells. That was due to poor pore filling of the dye-loaded TiO2 film by the spin-coated spiro-MeOTAD and to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator. However, the presence of the donor moieties in P1 that are structurally similar to spiro-MeOTAD was found to improve the wettability of the P1-loaded TiO2 film. As a consequence the performance of the P1-based solid-state cells is better compared to the cells based on non-spiro compounds.

Quality oriented drying of Lemon Balm (Melissa officinalis L.)

Heilkräuter sind während des Trocknungsprozesses zahlreichen Einflüssen ausgesetzt, welche die Qualität des Endproduktes entscheidend beeinflussen. Diese Forschungsarbeit beschäftigt sich mit der Trocknung von Zitronenmelisse (Melissa officinalis .L) zu einem qualitativ hochwertigen Endprodukt. Es werden Strategien zur Trocknung vorgeschlagen, die experimentelle und mathematische Aspekte mit einbeziehen, um bei einer adäquaten Produktivität die erforderlichen Qualitätsmerkmale im Hinblick auf Farbeänderung und Gehalt an ätherischen Ölen zu erzielen. Getrocknete Zitronenmelisse kann zurzeit, auf Grund verschiedener Probleme beim Trocknungsvorgang, den hohen Qualitätsanforderungen des Marktes nicht immer genügen. Es gibt keine standardisierten Informationen zu den einzelnen und komplexen Trocknungsparametern. In der Praxis beruht die Trocknung auf Erfahrungswerten, bzw. werden Vorgehensweisen bei der Trocknung anderer Pflanzen kopiert, und oftmals ist die Trocknung nicht reproduzierbar, oder beruht auf subjektiven Annäherungen. Als Folge dieser nicht angepassten Wahl der Trocknungsparameter entstehen oftmals Probleme wie eine Übertrocknung, was zu erhöhten Bruchverlusten der Blattmasse führt, oder eine zu geringe Trocknung, was wiederum einen zu hohen Endfeuchtegehalt im Produkt zur Folge hat. Dies wiederum mündet zwangsläufig in einer nicht vertretbaren Farbänderung und einen übermäßigen Verlust an ätherischen Ölen. Auf Grund der unterschiedlichen thermischen und mechanischen Eigenschaften von Blättern und Stängel, ist eine ungleichmäßige Trocknung die Regel. Es wird außerdem eine unnötig lange Trocknungsdauer beobachtet, die zu einem erhöhten Energieverbrauch führt. Das Trocknen in solaren Tunneln Trocknern bringt folgendes Problem mit sich: wegen des ungeregelten Strahlungseinfalles ist es schwierig die Trocknungstemperatur zu regulieren. Ebenso beeinflusst die Strahlung die Farbe des Produktes auf Grund von photochemischen Reaktionen. Zusätzlich erzeugen die hohen Schwankungen der Strahlung, der Temperatur und der Luftfeuchtigkeit instabile Bedingungen für eine gleichmäßige und kontrollierbare Trocknung. In Anbetracht der erwähnten Probleme werden folgende Forschungsschwerpunkte in dieser Arbeit gesetzt: neue Strategien zur Verbesserung der Qualität werden entwickelt, mit dem Ziel die Trocknungszeit und den Energieverbrauch zu verringern. Um eine Methodik vorzuschlagen, die auf optimalen Trocknungsparameter beruht, wurden Temperatur und Luftfeuchtigkeit als Variable in Abhängigkeit der Trocknungszeit, des ätherischer Ölgehaltes, der Farbänderung und der erforderliche Energie betrachtet. Außerdem wurden die genannten Parametern und deren Auswirkungen auf die Qualitätsmerkmale in solaren Tunnel Trocknern analysiert. Um diese Ziele zu erreichen, wurden unterschiedliche Ansätze verfolgt. Die Sorption-Isothermen und die Trocknungskinetik von Zitronenmelisse und deren entsprechende Anpassung an verschiedene mathematische Modelle wurden erarbeitet. Ebenso wurde eine alternative gestaffelte Trocknung in gestufte Schritte vorgenommen, um die Qualität des Endproduktes zu erhöhen und gleichzeitig den Gesamtenergieverbrauch zu senken. Zusätzlich wurde ein statistischer Versuchsplan nach der CCD-Methode (Central Composite Design) und der RSM-Methode (Response Surface Methodology) vorgeschlagen, um die gewünschten Qualitätsmerkmalen und den notwendigen Energieeinsatz in Abhängigkeit von Lufttemperatur und Luftfeuchtigkeit zu erzielen. Anhand der gewonnenen Daten wurden Regressionsmodelle erzeugt, und das Verhalten des Trocknungsverfahrens wurde beschrieben. Schließlich wurde eine statistische DOE-Versuchsplanung (design of experiments) angewandt, um den Einfluss der Parameter auf die zu erzielende Produktqualität in einem solaren Tunnel Trockner zu bewerten. Die Wirkungen der Beschattung, der Lage im Tunnel, des Befüllungsgrades und der Luftgeschwindigkeit auf Trocknungszeit, Farbänderung und dem Gehalt an ätherischem Öl, wurde analysiert. Ebenso wurden entsprechende Regressionsmodelle bei der Anwendung in solaren Tunneltrocknern erarbeitet. Die wesentlichen Ergebnisse werden in Bezug auf optimale Trocknungsparameter in Bezug auf Qualität und Energieverbrauch analysiert.

Resource use pattern and agroecosystem functioning in Rawanganga micro-watershed in Garhwal Himalaya, India

Agro-ecological resource use pattern in a traditional hill agricultural watershed in Garhwal Himalaya was analysed along an altitudinal transect. Thirty one food crops were found, although only 0.5% agriculture land is under irrigation in the area. Fifteen different tree species within agroforestry systems were located and their density varied from 30-90 trees/ha. Grain yield, fodder from agroforest trees and crop residue were observed to be highest between 1200 and 1600 m a.s.l. Also the annual energy input- output ratio per hectare was highest between 1200 and 1600 m a.s.l. (1.46). This higher input- output ratio between 1200-1600 m a.s.l. was attributed to the fact that green fodder, obtained from agroforestry trees, was considered as farm produce. The energy budget across altitudinal zones revealed 95% contribution of the farmyard manure and the maximum output was in terms of either crop residue (35%) or fodder (55%) from the agroforestry component. Presently on average 23%, 29% and 41% cattle were dependent on stall feeding in villages located at higher, lower and middle altitudes respectively. Similarly, fuel wood consumption was greatly influenced by altitude and family size. The efficiency and sustainability of the hill agroecosystem can be restored by strengthening of the agroforestry component. The approach will be appreciated by the local communities and will readily find their acceptance and can ensure their effective participation in the programme.

Memory Hierarchy Hardware-Software Co-design in Embedded Systems

The memory hierarchy is the main bottleneck in modern computer systems as the gap between the speed of the processor and the memory continues to grow larger. The situation in embedded systems is even worse. The memory hierarchy consumes a large amount of chip area and energy, which are precious resources in embedded systems. Moreover, embedded systems have multiple design objectives such as performance, energy consumption, and area, etc. Customizing the memory hierarchy for specific applications is a very important way to take full advantage of limited resources to maximize the performance. However, the traditional custom memory hierarchy design methodologies are phase-ordered. They separate the application optimization from the memory hierarchy architecture design, which tend to result in local-optimal solutions. In traditional Hardware-Software co-design methodologies, much of the work has focused on utilizing reconfigurable logic to partition the computation. However, utilizing reconfigurable logic to perform the memory hierarchy design is seldom addressed. In this paper, we propose a new framework for designing memory hierarchy for embedded systems. The framework will take advantage of the flexible reconfigurable logic to customize the memory hierarchy for specific applications. It combines the application optimization and memory hierarchy design together to obtain a global-optimal solution. Using the framework, we performed a case study to design a new software-controlled instruction memory that showed promising potential.

Estudio del proceso de calificación energética de un edificio de salida de telecabinas situado en Espui ‪(‬Lleida‪)‬ mediante herramientas de simulación energética

Per tal que un edifici de sortida de telecabines d'Espui obtingui una qualificació energètica, es fa un estudi mitjançant sistemes de simulació energètica

Ángel López: "Hem de fer que les indústries creixin sense comprometre el desenvolupament futur"

La Càtedra de Processos Industrials Sostenibles busca proporcionar instruments que contribueixin a difondre la cultura de l'optimització dels recursos. Es tracta de formar tècnics que ajudin la indústria a consumir millor

La tecnología del hidrógeno, una oportunidad estratégica para la perdurabilidad del sector energético en Colombia

El incremento de la actividad humana en el último siglo y el desarrollo de tecnologías ligadas con el petróleo como vector energético, han generado efectos medioambientales adversos que aunados con las limitadas reservas mundiales de crudo y su estrecha relación con el crecimiento económico mundial ha generado presiones economías, políticas y sociales en todos los países. Esta situación ha dinamizado la investigación y desarrollo de nuevas tecnologías basadas en el hidrogeno como un nuevo vector energético tecnológicamente compatible que permita la portabilidad de energía con el menor impacto ambiental y económico a la luz de la prospectiva de consumo y la perdurabilidad energética. Este trabajo identifica las experiencias más relevantes respecto a la tecnología del hidrogeno a nivel mundial con el fin de consolidar un plan estratégico para la incorporación del hidrógeno como vector energético al portafolio productivo colombiano mediante la aplicación de un modelo que permite el análisis del nivel de integración de los sectores educativo, empresarial y gubernamental, teniendo como base los resultados del análisis estructural y análisis de actores.

Modelo de recolección de residuos sólidos botellas plásticas y latas utilizando como aliado el sistema de transporte masivo en Bogotá

En las grandes ciudades, la disposición de residuos se ha convertido en un problema ambiental de magnitud mundial con impacto negativo por el manejo inadecuado de los residuos sólidos diarios. El propósito es utilizar el sistema de transporte publico de Bogotá (Transmilenio) como punto de recolección de botellas plásticas y latas, para crear un proyecto de responsabilidad ambiental el cual tendrá resultados positivos a nivel cultural, social, y a largo plazo, financieramente. A través del estudio de diferentes propuestas tanto locales como internacionales, fueron identificados los principales factores de éxito de estos proyectos los cuales se incluyeron para adecuar la presente propuesta para la ciudad de Bogotá teniendo en cuenta sus actuales condiciones. Después de identificar las características requeridas para Bogotá, se realizó un estudio demográfico para poder saber cuántos ciudadanos estarían dispuestos a participar. Como resultado, muchos pasajeros de Transmilenio esperan una retribución económica en el costo del pasaje del sistema. La prueba piloto se diseñó de acuerdo con la cantidad de envases recolectados, incluyendo el tipo de vehículos, como también la cantidad de personas y maquinas necesarias para el éxito del proyecto. Con la propuesta del proyecto completa, se realiza una evaluación financiera y económica para identificar los costos y gastos. La conclusión final de esta propuesta es que el modelo propuesto puede ser aplicado en Bogotá dadas sus características. Los beneficios sociales y ambientales también se destacan, como también el cambio cultural por parte de los ciudadanos hacia las prácticas ecológicas.

Avaluació del procés de desintegració de papers recuperats

La desintegració és una etapa important en la recuperació de paper vell, ja que té importants conseqüències en consum d'energia i en el comportament de les etapes posteriors. Per això els objectius es centren en analitzar la desintegració des del punt de vista del temps de desintegració, els aspectes energètics, modelització de la màquina de desintegració utilitzada i anàlisi dels factors de cisallament calculats com a mesura global de les forces implicades en la desintegració. Els autors que hi han treballat donen diferents explicacions a aquestes forces. Fins avui només s'ha pogut avaluar qualitativament la influència que tenen cada un dels mecanismes en el temps necessari per a desintegrar i en el consum energètic. Les característiques reològiques de les suspensions papereres, i el seu comportament no newtonià tenen una clara influència en el consum energètic i les forces de desfibrat en el desintegrador. Els experiments de desintegració s'han realitzat en un púlper convencional, amb tres tipus de paper recuperat: paper estucat d'alta qualitat imprès offset (PQ), paper revista estucat imprès en color (PR), paper blanc imprès en impresora làsser (PF). Anàlisi del temps de desintegració Per cada un del papers estudiats (PQ, PR i PF), les fraccions màssiques des de 0.06 fins a la màxima que estat possible per cada paper (de 0.14 a 0.18), i a dues velocitats d'agitació diferents, s'ha determinat el temps de desintegració (tD) fins a aconseguir un índex de Sommerville de 0.01%. S'obté que en augmentar la fracció màssica disminueix potencialment el temps de desintegració. S'ha estudiat la velocitat de desintegració, la producció teòrica del púlper en cada cas, i la seva relació amb les forces d'impacte i de fregament que produeixen la desintegració. Aspectes energètics El consum específic d'energia (SEC), definit com l'energia consumida per a desintegrar 1 kg de paper recuperat, disminueix molt en augmentar Xm, ja que a més de disminuir l'energia consumida en cada desintegració, el contingut en paper és més elevat. Pel disseny de desintegradors, cal tenir en compte que en augmentar Xm i en augmentar la velocitat, sempre augmenta la potència consumida. Però així com els beneficis de treballar a Xm alt són de 10 vegades en termes de SEC i de producció, l'augment de potència és només de l'ordre de 2 vegades la necessària respecte de la Xm baixa. Viscositat aparent i energia de fluidització S'estudia la relació entre el temps de desintegració, les forces de fregament i els valors de viscositat aparent de la bibliografia. Per cada paper i velocitat s'ha observat que el consum específic d'energia disminueix en funció de la viscositat aparent. Reologia del púlper Utilitzant el mètode de Metzner i Otto (1957) per determinar la viscositat aparent mitjana de les suspensions papereres, modificat per Roustan, s'ha caracteritzat el pulper mitjançant el model: Np= K· Rex·Fry S'han utilitzat dissolucions de glicerina com a fluid newtonià per a calcular les constants d'ajust, i a partir d'aquí, aïllar la viscositat aparent en funció de la potència neta i els paràmetres d'agitació. La viscositat aparent, d'acord amb Fabry (1999) es substitueix pel concepte de factor de cisallament. Factor de cisallament Calculat el factor de cisallament per a cada paperot i condicions d'agitació, s'ha relacionat amb Xm, SEC, tD, consum de potència, potència instal·lada i fracció cel·lulòsica. El factor de cisallament és un paràmetre útil per a quantificar les forces globals implicades en la desintegració.

Composition and cure temperature: The influence on properties of final flexible PU cold cure foam parts

Foams are cellular structures, produced by gas bubbles formed during the polyurethane polymerization mixture. Flexible PU foams meet the following two criteria: have a limited resistance to an applied load, being both permeable to air and reversibly deformable. There are two main types of flexible foams, hot and cold cure foams differing in composition and processing temperatures. The hot cure foams are widely applied and represent the main composition of actual foams, while cold cure foams present several processing and property advantages, e.g, faster demoulding time, better humid aging properties and more versatility, as hardness variation with index changes are greater than with hot cure foams. The processing of cold cure foams also is attractive due to the low energy consumption (mould temperature from 30 degrees to 65 degrees C) comparatively to hot cure foams (mould temperature from 30 degrees to 250 degrees C). Another advantage is the high variety of soft materials for low temperature processing moulds. Cold cure foams are diphenylmethane diisocyanate (MDI) based while hot cure foams are toluene diisocyanate (TDI) based. This study is concerned with Viscoelastic flexible foams MDI based for medical applications. Differential Scanning Calorimetry (DSC) was used to characterize the cure kinetics and Dynamical Mechanical Analisys to collect mechanical data. The data obtained from these two experimental procedures were analyzed and associated to establish processing/properties/operation conditions relationships. These maps for the selection of optimized processing/properties/operation conditions are important to achieve better final part properties at lower costs and lead times.

A sensor based intelligent building assessment model

While building provides shelter for human being, the previous models for assessing the intelligence of a building seldom consider the responses of occupants. In addition, the assessment is usually conducted by an authority organization on a yearly basis, thus can seldom provide timely assistance for facility manager to improve his daily facility maintenance performance. By the extending the law of entropy into the area of intelligent building, this paper demonstrate that both energy consumption and the response of occupants are important when partially assessing the intelligence of a building. This study then develops a sensor based real time building intelligence (BI) assessment model. An experimental case study demonstrates how the model can be implemented. The developed model can address the two demerits of the previous BI assessment model.

Performance of phase change material boards under natural convection

The high thermal storage capacity of phase change material (PCM) can reduce energy consumption in buildings through energy storage and release when combined with renewable energy sources, night cooling, etc. PCM boards can be used to absorb heat gains during daytime and release heat at night. In this paper, the thermal performance of an environmental chamber fitted with phase change material boards has been investigated. During a full-cycle experiment, i.e. charging–releasing cycle, the PCM boards on a wall can reduce the interior wall surface temperature during the charging process, whereas the PCM wall surface temperature is higher than that of the other walls during the heat releasing process. It is found that the heat flux density of the PCM wall in the melting zone is almost twice as large as that of ordinary wall. Also, the heat-insulation performance of a PCM wall is better than that of an ordinary wall during the charging process, while during the heat discharging process, the PCM wall releases more heat energy. The convective heat transfer coefficient of PCM wall surface calculated using equations for a normal wall material produces an underestimation of this coefficient. The high convective heat transfer coefficient for a PCM wall is due to the increased energy exchange between the wall and indoor air.

Impact of transmission errors in enhanced relay-enabled distributed coordination function

This paper analyzes the performance of Enhanced relay-enabled Distributed Coordination Function (ErDCF) for wireless ad hoc networks under transmission errors. The idea of ErDCF is to use high data rate nodes to work as relays for the low data rate nodes. ErDCF achieves higher throughput and reduces energy consumption compared to IEEE 802.11 Distributed Coordination Function (DCF) in an ideal channel environment. However, there is a possibility that this expected gain may decrease in the presence of transmission errors. In this work, we modify the saturation throughput model of ErDCF to accurately reflect the impact of transmission errors under different rate combinations. It turns out that the throughput gain of ErDCF can still be maintained under reasonable link quality and distance.

Performance evaluation of enhanced relay-enabled distributed coordination function

In this paper we evaluate the performance of our earlier proposed enhanced relay-enabled distributed coordination function (ErDCF) for wireless ad hoc networks. The idea of ErDCF is to use high data rate nodes to work as relays for the low data rate nodes. ErDCF achieves higher throughput and reduced energy consumption compared to IEEE 802.11 distributed coordination function (DCF). This is a result of. 1) using relay which helps to increase the throughput and lower overall blocking time of nodes due to faster dual-hop transmission, 2) using dynamic preamble (i.e. using short preamble for the relay transmission) which further increases the throughput and lower overall blocking time and also by 3) reducing unnecessary overhearing (by other nodes not involved in transmission). We evaluate the throughput and energy performance of the ErDCF with different rate combinations. ErDCF (11,11) (ie. R1=R2=11 Mbps) yields a throughput improvement of 92.9% (at the packet length of 1000 bytes) and an energy saving of 72.2% at 50 nodes.

An enhanced relay-enabled medium access control protocol for wireless ad hoc networks

In this paper we propose an enhanced relay-enabled distributed coordination function (rDCF) for wireless ad hoc networks. The idea of rDCF is to use high data rate nodes to work as relays for the low data rate nodes. The relay helps to increase the throughput and lower overall blocking time of nodes due to faster dual-hop transmission. rDCF achieves higher throughput over IEEE 802.11 distributed coordination function (DCF). The protocol is further enhanced for higher throughput and reduced energy. These enhancements result from the use of a dynamic preamble (i.e. using short preamble for the relay transmission) and also by reducing unnecessary overhearing (by other nodes not involved in transmission). We have modeled the energy consumption of rDCF, showing that rDCF provides an energy efficiency of 21.7% at 50 nodes over 802.11 DCF. Compared with the existing rDCF, the enhanced rDCF (ErDCF) scheme proposed in this paper yields a throughput improvement of 16.54% (at the packet length of 1000 bytes) and an energy saving of 53% at 50 nodes.