An optimized QoS scheme for IMS-NEMO in heterogeneous networks

The network mobility (NEMO) is proposed to support the mobility management when users move as a whole. In IP Multimedia Subsystem (IMS), the individual Quality of Service (QoS) control for NEMO results in excessive signaling cost. On the other hand, current QoS schemes have two drawbacks: unawareness of the heterogeneous wireless environment and inefficient utilization of the reserved bandwidth. To solve these problems, we present a novel heterogeneous bandwidth sharing (HBS) scheme for QoS provision under IMS-based NEMO (IMS-NEMO). The HBS scheme selects the most suitable access network for each session and enables the new coming non-real-time sessions to share bandwidth with the Variable Bit Rate (VBR) coded media flows. The modeling and simulation results demonstrate that the HBS can satisfy users' QoS requirement and obtain a more efficient use of the scarce wireless bandwidth.

Spatial effects on rural commerce

Commerce in rural territories should not be considered as a needed service, but as a basic infrastructure, that impact not only existent population, but also tourism, and rural industrialization. So, the rural areas need not only agriculture but industry and services, to have a global and balanced development, including for the countryside and the population. In the work presented in this paper, we are considering the formulation of the direct relation between population and the endowment of commerce sites within a geographical territory, the ?area of commercial interactions?. These are the closer set of towns that can gravitate to each other to cover the required needs for the populations within the area. The products retailed, range from basic products for the daily lives, to all other products for industry, agriculture, and services. The econometric spatial model developed to evaluate the interactions and estimate the parameters, is based on the Spatial Error Model, which allows for other spatial hidden effects to be considered without direct interference to the commercial disposition. The data and territory used to test the model correspond to a rural area in the Spanish Palencia territory (NUTS-3 level). The parameters have dependence from population levels, local rent per head, local and regional government budgets, and particular spatial restrictions. Interesting results are emerging form the model. The more significant is that the spatial effects can replace some number of commerce sites in towns, given the right spatial distribution of the sites and the towns. This is equivalent to consider the area of commercial interactions as the unit of measurement for the basic infrastructure and not only the towns.

Control of integrated unit operations

As a thermal separation method, distillation is one of the most important technologies in the chemical industry. Given its importance, it is no surprise that increasing efforts have been made in reducing its energy inefficiencies. A great deal of research is focused in the design and optimization of the Divided-Wall Column. Its applications are still reduced due to distrust of its controllability. Previous references studied the decentralized control of DWC but still few papers deal about Model Predictive Control. In this work we present a decentralized control of both a DWC column along with its equivalent MPC schema.

Information integration: from P&I diagrams to functional models

Information integration is a very important topic. Reusing the knowledge and having common and exchangeable representations have been an active research topic in process systems engineering. In this paper we deal with information integration in two different ways, the first one sharing knowledge between different heterogeneous applications and the second one integrating two different (but complementary) types of knowledge: functional and structural. A new architecture to integrate these representation and use for several purposes is presented in this paper.

Intermittency reinjection probability density function with and without noise effects.

Intermittency phenomenon is a continuous route from regular to chaotic behaviour. Intermittency is an occurrence of a signal that alternates chaotic bursts between quasi-regular periods called laminar phases, driven by the so called reinjection probability density function (RPD). In this paper is introduced a new technique to obtain the RPD for type-II and III intermittency. The new RPD is more general than the classical one and includes the classical RPD as a particular case. The probabilities of the laminar length, the average laminar lengths and the characteristic relations are determined with and without lower bound of the reinjection in agreement with numerical simulations. Finally, it is analyzed the noise effect in intermittency. A method to obtain the noisy RPD is developed extending the procedure used in the noiseless case. The analytical results show a good agreement with numerical simulations.

A CAD framework for the characterization and use of Memristor models

In the recent years the missing fourth component, the memristor, was successfully synthesized. However, the mathematical complexity and variety of the models behind this component, in addition to the existence of convergence problems in the simulations, make the design of memristor-based applications long and difficult. In this work we present a memristor model characterization framework which supports the automated generation of subcircuit files. The proposed environment allows the designer to choose and parameterize the memristor model that best suits for a given application. The framework carries out characterizing simulations in order to study the possible non-convergence problems, solving the dependence on the simulation conditions and guaranteeing the functionality and performance of the design. Additionally, the occurrence of undesirable effects related to PVT variations is also taken into account. By performing a Monte Carlo or a corner analysis, the designer is aware of the safety margins which assure the correct device operation.

Temperature Sensor Placement Including Routing Overhead and Sampling Inaccuracies

Dynamic thermal management techniques require a collection of on-chip thermal sensors that imply a significant area and power overhead. Finding the optimum number of temperature monitors and their location on the chip surface to optimize accuracy is an NP-hard problem. In this work we improve the modeling of the problem by including area, power and networking constraints along with the consideration of three inaccuracy terms: spatial errors, sampling rate errors and monitor-inherent errors. The problem is solved by the simulated annealing algorithm. We apply the algorithm to a test case employing three different types of monitors to highlight the importance of the different metrics. Finally we present a case study of the Alpha 21364 processor under two different constraint scenarios.

Towards a conceptual remodeling of information technologies based on a broad consideration of complexity

Actas.

Proposal of a three level complexity model for office automation

Office automation is one of the fields where the complexity related with technologies and working environments can be best shown. This is the starting point we have chosen to build up a theoretical model that shows us a scene quite different from the one traditionally considered. Through the development of the model, the levels of complexity associated with office automation and office environments have been identified, establishing a relationship between them. Thus, the model allows to state a general principle for sociotechnical design of office automation systems, comprising the ontological distinctions needed to properly evaluate each particular technology and its virtual contribution to office automation. From this fact comes the model's taxonomic ability to draw a global perspective of the state-of-art in office automation technologies.

Some minor problems with B.E.M.

As it is well known B.E.M. works efficiently in the treatment of a bread class of potential and elasticity problems. In this paper we present the results of several runs established with linear elements in plane potential theory and treating the importance of singularities and the pattern and size of elements used in the boundary discretization.

An algorithm for controllability in complex networks

In this paper structural controllability of complex networks is anyzed. A new algorithm is proposed which constructs a structural control scheme for a given network by avoiding the absence of dilations and by guaranteeing the accessibility of all nodes. Such accessibility is solved via a wiring procedure; this procedure, based on determining the non-accessible regions of the network, has been improved in this new proposed algorithm. This way, the number of dedicated controllers is reduced with respect to the one provided by previous existing algorithms.

Model Based On-Line Energy Prediction System for Semi-Autonomous Mobile Robots

Maximizing energy autonomy is a consistent challenge when deploying mobile robots in ionizing radiation or other hazardous environments. Having a reliable robot system is essential for successful execution of missions and to avoid manual recovery of the robots in environments that are harmful to human beings. For deployment of robots missions at short notice, the ability to know beforehand the energy required for performing the task is essential. This paper presents a on-line method for predicting energy requirements based on the pre-determined power models for a mobile robot. A small mobile robot, Khepera III is used for the experimental study and the results are promising with high prediction accuracy. The applications of the energy prediction models in energy optimization and simulations are also discussed along with examples of significant energy savings.

Biomechanical evaluation of the singing voice

Teaching the adequate use of the singing voice conveys a lot of knowledge in musical performance as well as in objective estimation techniques involving the use of air, muscles, room and body acoustics, and the tuning of a fine instrument as the human voice. Although subjective evaluation and training is a very delicate task to be carried out only by expert singers, biomedical engineering may help contributing with well-funded methodologies developed for the study of voice pathology. The present work is a preliminary study of exploratory character describing the performance of a student singer in a regular classroom under the point of view of vocal fold biomechanics. Estimates of biomechanical parameters obtained from singing voice are given and their potential use is discussed.

Conditional density approximations with mixtures of polynomials

Mixtures of polynomials (MoPs) are a non-parametric density estimation technique especially designed for hybrid Bayesian networks with continuous and discrete variables. Algorithms to learn one- and multi-dimensional (marginal) MoPs from data have recently been proposed. In this paper we introduce two methods for learning MoP approximations of conditional densities from data. Both approaches are based on learning MoP approximations of the joint density and the marginal density of the conditioning variables, but they differ as to how the MoP approximation of the quotient of the two densities is found. We illustrate and study the methods using data sampled from known parametric distributions, and we demonstrate their applicability by learning models based on real neuroscience data. Finally, we compare the performance of the proposed methods with an approach for learning mixtures of truncated basis functions (MoTBFs). The empirical results show that the proposed methods generally yield models that are comparable to or significantly better than those found using the MoTBF-based method.

Influence of a liquid on the natural frequencies of almost circular plates

In this work, the influence of the surrounding fluid on the dynamic characteristics of almost circular plates is investigated. First the natural frequencies and normal modes for the plates in vacuum are calculated by a perturbation procedure. The method is applied for the case of elliptical plates with a low value of eccentricity. The results are compared with other available methods for this type of plates with good agreement. Next, the effect of the fluid is considered. The normal modes of the plate in vacuum are used as a base to express the vibration mode of the coupled plate-fluid system. By applying the Hankel transformation the nondimensional added virtual mass 2 increment (NAVMI) are calculated for elliptical plates. Results of the NAVMI factors and the effect of the fluid on the natural frequencies are given and it is shown that when the eccentricity of the plate is reduced to zero (circular plate) the known results of the natural frequencies for circular plates surrounded by liquid are recovered.