Novel titania sol-gel derived film for luminescence-based oxygen sensing.

A novel method for the preparation of titania sol–gel derived oxygen sensors based on the ruthenium(II) dye, [Ru(bpy)3]2+, is described. A titania sol–gel paste film was cast onto microscope slides, and the dye ion-paired to the deprotonated, hydroxylated groups on the film's surface from an aqueous solution of the dye at pH 11. The resulting sensor film is extremely oxygen sensitive, with a PO2 (S = 1/2) value (i.e. the partial pressure of oxygen required in order to reduce the original, oxygen free, luminescence intensity by 50%) of 0.011 atm. The sensor undergoes 95% response to oxygen in 4 s, and shows 95% recovery of its luminescence in argon within 7 s.

The Use of High Surface Area Silica and Supercritical Carbon Dioxide to Enhance Solubility of Poorly Water-Soluble Drugs

Purpose Poor water-solubility of BCS class II drugs can limit their commercialization because of reduced oral bioavailability. It has been reported that loading of drug by adsorption onto porous silica would enhance drug solubility due to the increased surface area available for solvent diffusion. In this work, solid dispersions are formed using supercritical carbon dioxide (scCO2). The aim of this research was to characterise the solid-state properties of scCO2 dispersion and to investigate the impact of altering scCO2 processing conditions on final amorphous product performance that could lead to enhancement of drug dissolution rate for BCS class II drugs. Methods Indomethacin (IND) was purchased from Sigma-Aldrich (Dorset, UK) and was used as a model drug with two grades of high surface area silica (average particle sizes 3&[micro] and 7&[micro]), which were obtained directly from Grace-Davison (Germany). Material crystallinity was evaluated using powder X-ray diffraction (PXRD, Rigaku™, miniflex II, Japan) and high-speed differential scanning calorimetry (Hyper-DSC 8000, Perkin Elmer, USA). Materials were placed in a high-pressure vessel consisting of a CO2 cylinder, a Thar™ Technologies P50 high-pressure pump and a 750 ml high-pressure vessel (Thar, USA). Physical mixtures were exposed to CO2 gas above its critical conditions. SEM imaging and elemental analysis were conducted using a Jeol 6500 FEGSEM (Advanced MicroBeam Inc., Austria). Drug release was examined using USP type II dissolution tester (Caleva™, UK). Results The two grades of silica were found to be amorphous using PXRD and Hyper-DSC. Using PXRD, it was shown that an increase in incubation time and pressure resulted in a decrease in the crystalline content. Drug release profiles from the two different silica formulations prepared under the same conditions are shown in Figure 1. It was found that there was a significant enhancement in drug release, which was influenced, by silica type and other experiment conditions such as temperature, pressure and exposure time. SEM imaging and elemental analysis showed drug deposited inside silica pores as well as on the outer surface. Conclusion This project has shown that silica carrier platforms may be used as an alternative approach to generating polymeric solid dispersions of amorphous drugs exhibiting enhanced solubility.

Ectopic bone formation in rapidly fabricated acellular injectable dense collagen-Bioglass hybrid scaffolds via gel aspiration-ejection

Gel aspiration-ejection (GAE) has recently been introduced as an effective technique for the rapid production of injectable dense collagen (IDC) gel scaffolds with tunable collagen fibrillar densities (CFDs) and microstructures. Herein, a GAE system was applied for the advanced production and delivery of IDC and IDC-Bioglass® (IDC-BG) hybrid gel scaffolds for potential bone tissue engineering applications. The efficacy of GAE in generating mineralizable IDC-BG gels (from an initial 75-25 collagen-BG ratio) produced through needle gauge numbers 8G (3.4 mm diameter and 6 wt% CFD) and 14G (1.6 mm diameter and 14 wt% CFD) was investigated. Second harmonic generation (SHG) imaging of as-made gels revealed an increase in collagen fibril alignment with needle gauge number. In vitro mineralization of IDC-BG gels was confirmed where carbonated hydroxyapatite was detected as early as day 1 in simulated body fluid, which progressively increased up to day 14. In vivo mineralization of, and host response to, acellular IDC and IDC-BG gel scaffolds were further investigated following subcutaneous injection in adult rats. Mineralization, neovascularization and cell infiltration into the scaffolds was enhanced by the addition of BG and at day 21 post injection, there was evidence of remodelling of granulation tissue into woven bone-like tissue in IDC-BG. SHG imaging of explanted scaffolds indicated collagen fibril remodelling through cell infiltration and mineralization over time. In sum, the results suggest that IDC-BG hybrid gels have osteoinductive properties and potentially offer a novel therapeutic approach for procedures requiring the injectable delivery of a malleable and dynamic bone graft that mineralizes under physiological conditions

Lanthanide oxide nanotubes and nanorods: synthesis, processing, luminescence and catalytic properties

Esta tese relata estudos de síntese, caracterização da estrutura e das propriedades de fotoluminescência e aplicações de nanotubos e nanobastonetes de óxidos de lantanídeos em pontas para microscopia de força atómica, catálise heterogénea e compósitos de base polimérica. Há um interesse crescente em compreender como o confinamento quântico decorrente da redução do tamanho de partícula pode influenciar a eficiência da luminescência, a dinâmica dos estados excitados, a transferência de energia e os efeitos de termalização de nanoluminóforos. Em nanocristais dopados com lantanídeos (Ln3+), e apesar da localização dos estados 4f, ocorrem efeitos de confinamento quântico via interacção com os modos vibracionais da rede. Em particular, a termalização anómala, descrita para uma variedade de nanocristais dopados com Ln3+, tem sido atribuída à ausência de modos vibracionais de menor frequência. Este nanoconfinamento pode ter impacto na dinâmica da luminescência, bem como na transferência de energia mediada por modos vibracionais e processos de upconversion. Nesta tese, relata-se o estudo deste efeito em nanotubos de Gd2O3:Eu3+. A influência de parâmetros como a concentração de európio e as condições de calcinação também foi investigada. Algumas aplicações destes óxidos de lantanídeos também foram exploradas, nomeadamente a modificação de pontas usadas em microscopia de força atómica com nanobastonetes de Gd2O3:Eu3+, lograda através de dielectroforese, técnica que não degrada a emissão de luz (rendimento quântico 0.47). As pontas modificadas são estáveis sob condições de trabalho, podendo ser aplicadas, por exemplo, em microscopia óptica de varrimento de campo próximo (SNOM). A oxidação em fase líquida do etilbenzendo foi investigada usando como catalisador nanotubos de CeO2, em presença dos oxidantes hidroperóxido de t-butilo e H2O2, e do solvente acetonitrilo, e temperaturas entre 55 e 105 ºC. Nanobastonetes de Gd2O3:Eu3+ recobertos com sílica foram preparados pelo método sol-gel. Esta cobertura resultou num aumento, quer do rendimento quântico de emissão, de 0.51 para 0.86 (excitação a 255 nm), quer dos tempos de vida,de 1.43 para 1.80 ms (excitação a 394.4 nm). A superfície dos nanotubos cobertos com sílica foi modificada com o agente de acoplamento metacrilato de 3-(trimetoxissilil)propilo que permitiu a preparação de compósitos através da subsequente polimerização in-situ do estireno por técnicas de miniemulsão e solução. ABSTRACT: This thesis reports on the synthesis, characterisation of the structure and photoluminescence properties, and applications of nanotubes and nanorods of lanthanides oxides in atomic force microscopy tips, heterogeneous catalysis and polymer-base composites. There is a growing interest in understanding how size-dependent quantum confinement affects the photoluminescence efficiency, excited-state dynamics, energy-transfer and thermalisation phenomena in nanophosphors. For lanthanide (Ln3+)-doped nanocrystals, and despite the localisation of the 4f states, confinement effects are induced mostly via electron-phonon interactions. In particular, the anomalous thermalisation reported for a handful of Ln3+-doped nanocrystals has been rationalised by the absence of lowfrequency phonon modes. This nanoconfinement may further impact on the Ln3+ luminescence dynamics, such as phonon-assisted energy transfer or upconversion processes. Here, this effect is investigated in Gd2O3:Eu3+ nanotubes. The influence of parameters such as europium concentration and calcination procedure is also studied. Some applications of these lanthanides oxides have been explored, for instance the modification of atomic force microscopy tips with photoluminescent Gd2O3:Eu3+ nanorods, using dielectrophoresis, a technique which preserves the red emission of the nanorods (quantum yield 0.47). The modified tips are stable under working conditions and may find applications in scanning near-field optical microscopy. The liquid-phase oxidation of ethylbenzene over CeO2 nanotubes has been investigated, using tert-butyl-hydroperoxide and H2O2 as the oxidising agents, and acetonitrile as the solvent, in the range 55-105 ºC. Gd2O3:Eu3+ nanorods have been coated with silica via a sol-gel approach. The silica coating increases both, the Eu3+ absolute emission quantum yields from 0.51 to 0.86 (255 nm excitation), and decay times from 1.43 to 1.80 ms (394.4 nm excitation). The silica coating was modified with 3- (trimethoxysilyl) propyl methacrylate and, subsequently, composites have been prepared by in-situ radical polymerisation of styrene via miniemulsion and solution routes.

Active corrosion protection of AA2024 by sol-gel coatings with corrosion inhibitors

A indústria aeronáutica utiliza ligas de alumínio de alta resistência para o fabrico dos elementos estruturais dos aviões. As ligas usadas possuem excelentes propriedades mecânicas mas apresentam simultaneamente uma grande tendência para a corrosão. Por esta razão essas ligas necessitam de protecção anticorrosiva eficaz para poderem ser utilizadas com segurança. Até à data, os sistemas anticorrosivos mais eficazes para ligas de alumínio contêm crómio hexavalente na sua composição, sejam pré-tratamentos, camadas de conversão ou pigmentos anticorrosivos. O reconhecimento dos efeitos carcinogénicos do crómio hexavalente levou ao aparecimento de legislação banindo o uso desta forma de crómio pela indústria. Esta decisão trouxe a necessidade de encontrar alternativas ambientalmente inócuas mas igualmente eficazes. O principal objectivo do presente trabalho é o desenvolvimento de prétratamentos anticorrosivos activos para a liga de alumínio 2024, baseados em revestimentos híbridos produzidos pelo método sol-gel. Estes revestimentos deverão possuir boa aderência ao substrato metálico, boas propriedades barreira e capacidade anticorrosiva activa. A protecção activa pode ser alcançada através da incorporação de inibidores anticorrosivos no prétratamento. O objectivo foi atingido através de uma sucessão de etapas. Primeiro investigou-se em detalhe a corrosão localizada (por picada) da liga de alumínio 2024. Os resultados obtidos permitiram uma melhor compreensão da susceptibilidade desta liga a processos de corrosão localizada. Estudaram-se também vários possíveis inibidores de corrosão usando técnicas electroquímicas e microestruturais. Numa segunda etapa desenvolveram-se revestimentos anticorrosivos híbridos orgânico-inorgânico baseados no método sol-gel. Compostos derivados de titania e zirconia foram combinados com siloxanos organofuncionais a fim de obter-se boa aderência entre o revestimento e o substrato metálico assim como boas propriedades barreira. Testes industriais mostraram que estes novos revestimentos são compatíveis com os esquemas de pintura convencionais actualmente em uso. A estabilidade e o prazo de validade das formulações foram optimizados modificando a temperatura de armazenamento e a quantidade de água usada durante a síntese. As formulações sol-gel foram dopadas com os inibidores seleccionados durante a primeira etapa e as propriedades anticorrosivas passivas e activas dos revestimentos obtidos foram estudadas numa terceira etapa do trabalho. Os resultados comprovam a influência dos inibidores nas propriedades anticorrosivas dos revestimentos sol-gel. Em alguns casos a acção activa dos inibidores combinou-se com a protecção passiva dada pelo revestimento mas noutros casos terá ocorrido interacção química entre o inibidor e a matriz de sol-gel, de onde resultou a perda de propriedades protectoras do sistema combinado. Atendendo aos problemas provocados pela adição directa dos inibidores na formulação sol-gel procurou-se, numa quarta etapa, formas alternativas de incorporação. Na primeira, produziu-se uma camada de titania nanoporosa na superfície da liga metálica que serviu de reservatório para os inibidores. O revestimento sol-gel foi aplicado por cima da camada nanoporosa. Os inibidores armazenados nos poros actuam quando o substrato fica exposto ao ambiente agressivo. Numa segunda, os inibidores foram armazenados em nano-reservatórios de sílica ou em nanoargilas (halloysite), os quais foram revestidos por polielectrólitos montados camada a camada. A terceira alternativa consistiu no uso de nano-fios de molibdato de cério amorfo como inibidores anticorrosivos nanoparticulados. Os nano-reservatórios foram incorporados durante a síntese do sol-gel. Qualquer das abordagens permitiu eliminar o efeito negativo do inibidor sobre a estabilidade da matriz do sol-gel. Os revestimentos sol-gel desenvolvidos neste trabalho apresentaram protecção anticorrosiva activa e capacidade de auto-reparação. Os resultados obtidos mostraram o elevado potencial destes revestimentos para a protecção anticorrosiva da liga de alumínio 2024.

Corroles : synthesis, functionalization and application as chemosensors

O trabalho de investigação apresentado nesta dissertação foi desenvolvido tendo como objectivo a síntese e funcionalização de meso-triarilcorróis para utilização como quimiossensores. Este trabalho encontra-se apresentado ao longo de cinco capítulos. No primeiro capítulo são apresentadas as características gerais, as metodologias de síntese e de funcionalização de macrociclos de tipo corrólico, e descrevemse algumas aplicações em que têm sido utilizados. São ainda abordadas algumas das propriedades e características dos quimiossensores e os mecanismos de deteção de diversos analítos. No segundo capítulo, após uma pequena introdução às reações de Wittig e de Diels-Alder, escolhidas para a funcionalização do macrociclo corrólico, descreve-se o estudo efectuado para a obtenção do complexo de gálio(III) do 3- vinil-5,10,15-tris(pentafluorofenil)corrol e o seu comportamento como dieno, em reações de Diels-Alder na presença dos dienófilos 1,4-benzoquinona e 1,4- naftoquinona. Desses estudos resultaram dois aductos cuja habilidade sensorial, bem como a dos seus precursores, foi estudada, em solução, na presença de aniões esféricos (F-, Br-, Cl-), lineares (CN-) e volumosos (CH3COO-, H2PO4 -). Dos macrociclos estudados verificou-se que o corrol base-livre 5,10,15-tris(pentafluorofenil)corrol apresenta uma elevada sensibilidade para o anião fluoreto (F-), e que a coordenação do núcleo corrólico com gálio(III) diminui a afinidade para este anião. Em geral, todos os compostos mostraram afinidade para o anião cianeto (CN-) mesmo quando em suportes poliméricos. O gel de poliacrilamida revelou-se muito promissor na determinação de CN- em amostras de água. No terceiro capítulo é avaliada a reatividade do complexo de gálio(III) do 3- vinil-5,10,15-tris(pentafluorofenil)corrol ainda como dieno mas agora na presença de um dienófilo linear, o acetilenodicarboxilato de dimetilo. Desse estudo resultaram dois novos derivados corrólicos. A habilidade sensorial dos mesmos perante os aniões fluoreto, cianeto, acetato, e fosfato foi avaliada por espectroscopia de absorção e emissão tendo um dos aductos mostrado ser colorimétrico para o anião cianeto. No quarto capítulo descreve-se a síntese e caracterização de dois conjugados do tipo corrol-cumarina, resultantes de reações de Hetero-Diels-Alder entre o 3-vinil-5,10,15-tris(pentafluorofenil)corrolatogálio(III)(piridina) e orto-quinonasmetídeos gerados in situ a partir de reacções de Knoevenagel entre cumarinas e paraformaldeído. Realizaram-se estudos de afinidade sensorial para aniões e catiões com estes macrociclos, bem como com conjugados porfirinacumarina análogos. A inserção de uma unidade cumarina conferiu uma excepcional solubilidade tendo os novos derivados apresentado solubilidade em etanol. No quinto e último capítulo desta dissertação é avaliada a capacidade sensorial do 5,10,15-tris(pentafluorofenil)corrol e da sua espécie monoaniónica, para os catiões metálicos Na+, Ca2+, Cu2+, Cd2+, Pb2+, Hg2+, Ag+, Al3+, Zn2+, Ni2+, Cr3+, Ga3+, Fe3+ em tolueno e acetonitrilo. Os macrociclos corrólicos mostraram ser selectivos e colorimétricos para o catião Hg2+. Neste trabalho descreve-se ainda a síntese do derivado -iminocorrol, que após funcionalização com o 3-isocianatopropiltrimetoxisilano originou um derivado do tipo alcoxisilano, que foi, posteriormente, ancorado a nanopartículas comerciais de sílica. As novas nanopartículas ancoradas com o alcoxisilano corrol foram estudadas na presença de Cu2+, Hg2+ e Ag+. Na presença do catião Ag+ assistiu-se a uma mudança de cor, de verde para amarelo.

Surface reactivity enhancement of silica-based glass-ceramic scaffolds

A paradigm shift is taking place from using transplanting tissue and synthetic implants to a tissue engineering approach that aims to regenerate damaged tissues by combining cells from the body with highly porous scaffold biomaterials, which act as templates, guiding the growth of new tissue. The central focus of this thesis was to produce porous glass and glass-ceramic scaffolds that exhibits a bioactive and biocompatible behaviour with specific surface reactivity in synthetic physiological fluids and cell-scaffold interactions, enhanced by composition and thermal treatments applied. Understanding the sintering behaviour and the interaction between the densification and crystallization processes of glass powders was essential for assessing the ideal sintering conditions for obtaining a glass scaffolds for tissue engineering applications. Our main goal was to carry out a comprehensive study of the bioactive glass sintering, identifying the powder size and sintering variables effect, for future design of sintered glass scaffolds with competent microstructures. The developed scaffolds prepared by the salt sintering method using a 3CaO.P2O5 - SiO2 - MgO glass system, with additions of Na2O with a salt, NaCl, exhibit high porosity, interconnectivity, pore size distribution and mechanical strength suitable for bone repair applications. The replacement of 6 % MgO by Na2O in the glass network allowed to tailor the dissolution rate and bioactivity of the glass scaffolds. Regarding the biological assessment, the incorporation of sodium to the composition resulted in an inibition cell response for small periods. Nevertheless it was demonstrated that for 21 days the cells response recovered and are similar for both glass compositions. The in vitro behaviour of the glass scaffolds was tested by introducing scaffolds to simulated body fluid for 21 days. Energy-dispersive Xray spectroscopy and SEM analyses proved the existence of CaP crystals for both compositions. Crystallization forming whitlockite was observed to affect the dissolution behaviour in simulated body fluid. By performing different heat treatments, it was possible to control the bioactivity and biocompatability of the glass scaffolds by means of a controlled crystallization. To recover and tune the bioactivity of the glass-ceramic with 82 % crystalline phase, different methods have been applied including functionalization using 3- aminopropyl-triethoxysilane (APTES). The glass ceramic modified surface exhibited an accelerated crystalline hydroxyapatite layer formation upon immersion in SBF after 21 days while the as prepared glass-ceramic had no detected formation of calcium phosphate up to 5 months. A sufficient mechanical support for bone tissue regeneration that biodegrade later at a tailorable rate was achievable with the glass–ceramic scaffold. Considering the biological assessment, scaffolds demonstrated an inductive effect on the proliferation of cells. The cells showed a normal morphology and high growth rate when compared to standard culture plates. This study opens up new possibilities for using 3CaO.P2O5–SiO2–MgO glass to manufacture various structures, while tailoring their bioactivity by controlling the content of the crystalline phase. Additionally, the in vitro behaviour of these structures suggests the high potential of these materials to be used in the field of tissue regeneration.

Test and development of microcapsules for rigid polyurethane foam

Tese de mestrado em Química Tecnológica, apresentada à Universidade de Lisboa, através da Faculdade de Ciências, 2016

Myoglobin-biomimetic electroactive materials made by surface molecular imprinting on silica beads and their use as ionophores in polymeric membranes for potentiometric transduction

Myoglobin (Mb) is among the cardiac biomarkers playing a major role in urgent diagnosis of cardiovascular diseases. Its monitoring in point-of-care is therefore fundamental. Pursuing this goal, a novel biomimetic ionophore for the potentiometric transduction of Mb is presented. It was synthesized by surface molecular imprinting (SMI) with the purpose of developing highly efficient sensor layers for near-stereochemical recognition of Mb. The template (Mb) was imprinted on a silane surface that was covalently attached to silica beads by means of self-assembled monolayers. First the silica was modified with an external layer of aldehyde groups. Then, Mb was attached by reaction with its amine groups (on the external surface) and subsequent formation of imine bonds. The vacant places surrounding Mb were filled by polymerization of the silane monomers 3-aminopropyltrimethoxysilane (APTMS) and propyltrimethoxysilane (PTMS). Finally, the template was removed by imine cleavage after treatment with oxalic acid. The results materials were finely dispersed in plasticized PVC selective membranes and used as ionophores in potentiometric transduction. The best analytical features were found in HEPES buffer of pH 4. Under this condition, the limits of detection were of 1.3 × 10−6 mol/L for a linear response after 8.0 × 10−7 mol/L with an anionic slope of −65.9 mV/decade. The imprinting effect was tested by preparing non-imprinted (NI) particles and employing these materials as ionophores. The resulting membranes showed no ability to detect Mb. Good selectivity was observed towards creatinine, sacarose, fructose, galactose, sodium glutamate, and alanine. The analytical application was conducted successfully and showed accurate and precise results.

Transmission measurements using a new far-infrared set-up

A system comprised of a Martin-Puplett type polarizing interferometer and a Helium-3 cryostat was developed to study the transmission of materials in the very-far-infrared region of the spectrum. This region is of significant interest due to the low-energy excitations which many materials exhibit. The experimental transmission spectrum contains information concerning the optical properties of the material. The set-up of this system is described in detail along with the adaptations and improvements which have been made to the system to ensure the best results. Transmission experiments carried out with this new set-up for two different varieties of materials: superconducting thin films of lead and biological proteins, are discussed. Several thin films of lead deposited on fused silica quartz substrates were studied. From the ratio of the transmission in the superconducting state to that in the normal state the superconducting energy gap was determined to be approximately 25 cm-1 which corresponds to 2~/kBTc rv 5 in agreement with literature data. Furthermore, in agreement with theoretical predictions, the maximum in the transmission ratio was observed to increase as the film thickness was increased. These results provide verification of the system's ability to accurately measure the optical properties of thin low-Tc superconducting films. Transmission measurements were carried out on double deionized water, and a variety of different concentrations by weight of the globular protein, Bovine Serum Albumin, in the sol, gel and crystalline forms. The results of the water study agree well with literature values and thus further illustrate the reproducibility of the system. The results of the protein experiments, although preliminary, indicate that as the concentration increases the samples become more transparent. Some weak structure in the frequency dependent absorption coefficient, which is more prominent in crystalline samples, may be due to low frequency vibrations of the protein molecules.

Characterization of glutaraldehyde-immobilized chymotrypsin and an in-situ immobilized enzyme reactor using capillary electrophoresis-based peptide mapping

La digestion enzymatique des protéines est une méthode de base pour les études protéomiques ainsi que pour le séquençage en mode « bottom-up ». Les enzymes sont ajoutées soit en solution (phase homogène), soit directement sur le gel polyacrylamide selon la méthode déjà utilisée pour l’isolation de la protéine. Les enzymes protéolytiques immobilisées, c’est-à-dire insolubles, offrent plusieurs avantages tels que la réutilisation de l’enzyme, un rapport élevé d’enzyme-sur-substrat, et une intégration facile avec les systèmes fluidiques. Dans cette étude, la chymotrypsine (CT) a été immobilisée par réticulation avec le glutaraldehyde (GA), ce qui crée des particules insolubles. L’efficacité d’immobilisation, déterminée par spectrophotométrie d’absorbance, était de 96% de la masse totale de la CT ajouté. Plusieurs différentes conditions d’immobilisation (i.e., réticulation) tels que la composition/pH du tampon et la masse de CT durant la réticulation ainsi que les différentes conditions d’entreposage tels que la température, durée et humidité pour les particules GA-CT ont été évaluées par comparaison des cartes peptidiques en électrophorèse capillaire (CE) des protéines standards digérées par les particules. Les particules de GA-CT ont été utilisés pour digérer la BSA comme exemple d’une protéine repliée large qui requit une dénaturation préalable à la digestion, et pour digérer la caséine marquée avec de l’isothiocyanate de fluorescéine (FITC) comme exemple d’un substrat dérivé afin de vérifier l’activité enzymatique du GA-CT dans la présence des groupements fluorescents liés au substrat. La cartographie peptidique des digestions par les particules GA-CT a été réalisée par CE avec la détection par absorbance ultraviolet (UV) ou fluorescence induite par laser. La caséine-FITC a été, en effet, digérée par GA-CT au même degré que par la CT libre (i.e., soluble). Un microréacteur enzymatique (IMER) a été fabriqué par immobilisation de la CT dans un capillaire de silice fondu du diamètre interne de 250 µm prétraité avec du 3-aminopropyltriéthoxysilane afin de fonctionnaliser la paroi interne avec les groupements amines. Le GA a été réagit avec les groupements amine puis la CT a été immobilisée par réticulation avec le GA. Les IMERs à base de GA-CT étaient préparé à l’aide d’un système CE automatisé puis utilisé pour digérer la BSA, la myoglobine, un peptide ayant 9 résidus et un dipeptide comme exemples des substrats ayant taille large, moyenne et petite, respectivement. La comparaison des cartes peptidiques des digestats obtenues par CE-UV ou CE-spectrométrie de masse nous permettent d’étudier les conditions d’immobilisation en fonction de la composition et le pH du tampon et le temps de réaction de la réticulation. Une étude par microscopie de fluorescence, un outil utilisé pour examiner l’étendue et les endroits d’immobilisation GA-CT dans l’IMER, ont montré que l’immobilisation a eu lieu majoritairement sur la paroi et que la réticulation ne s’est étendue pas si loin au centre du capillaire qu’anticipée.

Preparation and characterization of nanocrystalline transition metal-loaded sulfated titania through sol-gel method

Transition metal-loaded (3%) nanocrystalline sulfated titania (ST) powders are prepared using the sol–gel technique. Anatase is found as the active phase in all the samples. Sulfate ion impregnation decreases the crystallite size and stabilizes the anatase phase of TiO2. Acidity of the samples is found to increase by the incorporation of sulfate ion and also by the modification by transition metal ions. All the prepared catalysts are found stable up to 700 °C.

A sensitive fibre optic pH sensor using multiple sol-gel coatings

The fabrication and characterization of a fibre optic pH sensor based on evanescent wave absorption is presented. The unclad portion of a multi-mode optical fibre is coated with a pH sensitive dye, which is immobilized by the sol–gel route. The sensitivity of the device has been found to increase when multiple sol–gel coatings are used as the sensing region. The dynamic range and the temporal response of the sensor are investigated for two different dyes, namely bromocresol purple and bromocresol green. The performance of the device is evaluated in terms of the results obtained during actual measurements.

Gel vs aceite mineral en el tratamiento del fotoenvejecimiento de manos con luz pulsada intensa

Introducción: En el tratamiento con Luz Pulsada Intensa (LPI) para el fotoenvejecimiento de las manos no se encuentran estudios que evidencien si existe alguna diferencia estadísticamente significativa en el grado de efectividad y seguridad al utilizar gel o aceite mineral como medios de acople. Objetivo: Determinar la efectividad y seguridad terapéutica en el uso de gel vs aceite mineral. Materiales y Métodos: Estudio observacional analítico de cohorte retrospectivo que involucró 29 pacientes. Realizado en tres fases; selección y recolección de las historias clínicas, evaluación fotográfica de registros pre tratamiento y pos tratamiento con determinación del grado de mejoría global en el fotoenvejecimiento de las manos por parte de tres evaluadores cegados, y análisis estadístico de los datos obtenidos por medio de las pruebas de Mann Whitney y Wilcoxon. Resultados: Se encontró mejoría dada por disminución en un grado del fotoenvejecimiento para los dos medios de acople con la misma significancia estadística. La percepción subjetiva mostró mejoría en todos los pacientes evaluados. La seguridad es similar en los dos grupos pero se evidenció mayor severidad en los efectos secundarios con el uso de aceite, con diferencias estadísticamente significativas en los efectos moderados y severos. Conclusión: La efectividad es la misma independiente del medio de acople que se use. La seguridad a pesar de evidenciar un perfil similar es mayor con el uso de gel en cuanto a la menor severidad de los efectos presentados. Se requieren más estudios de tipo ensayos clínicos controlados que permitan determinar una mayor evidencia.