A mathematical view of water table fluctuations in a shallow aquifer in Brazil

Detailed monitoring of the groundwater table can provide important data about both short- and long-term aquifer processes, including information useful for estimating recharge and facilitating groundwater modeling and remediation efforts. In this paper, we presents results of 4 years (2002 to 2005) of monitoring groundwater water levels in the Rio Claro Aquifer using observation wells drilled at the Rio Claro campus of São Paulo State University in Brazil. The data were used to follow natural periodic fluctuations in the water table, specifically those resulting from earth tides and seasonal recharge cycles. Statistical analyses included methods of time-series analysis using Fourier analysis, cross-correlation, and R/S analysis. Relationships could be established between rainfall and well recovery, as well as the persistence and degree of autocorrelation of the water table variations. We further used numerical solutions of the Richards equation to obtain estimates of the recharge rate and seasonable groundwater fluctuations. Seasonable soil moisture transit times through the vadose zone obtained with the numerical solution were very close to those obtained with the cross-correlation analysis. We also employed a little-used deep drainage boundary condition to obtain estimates of seasonable water table fluctuations, which were found to be consistent with observed transient groundwater levels during the period of study.

Development, validation, and application of a method for the GC-MS analysis of fipronil and three of its degradation products in samples of water, soil, and sediment

A method for the identification and quantification of pesticide residues in water, soil, and sediment samples has been developed, validated, and applied for the analysis of real samples. The specificity was determined by the retention time and the confirmation and quantification of analyte ions. Linearity was demonstrated over the concentration range of 20 to 120 µg L(-1), and the correlation coefficients varied between 0.979 and 0.996, depending on the analytes. The recovery rates for all analytes in the studied matrix were between 86% and 112%. The intermediate precision and repeatability were determined at three concentration levels (40, 80, and 120 µg L(-1)), with the relative standard deviation for the intermediate precision between 1% and 5.3% and the repeatability varying between 2% and 13.4% for individual analytes. The limits of detection and quantification for fipronil, fipronil sulfide, fipronil-sulfone, and fipronil-desulfinyl were 6.2, 3.0, 6.6, and 4.0 ng L(-1) and 20.4, 9.0, 21.6, and 13.0 ng L(-1), respectively. The method developed was used in water, soil, and sediment samples containing 2.1 mg L(-1) and 1.2% and 5.3% of carbon, respectively. The recovery of pesticides in the environmental matrices varied from 88.26 to 109.63% for the lowest fortification level (40 and 100 µg kg(-1)), from 91.17 to 110.18% for the intermediate level (80 and 200 µg kg(-1)), and from 89.09 to 109.82% for the highest fortification level (120 and 300 µg kg(-1)). The relative standard deviation for the recovery of pesticides was under 15%.

Spatial and temporal quality of water in the Itupararanga Reservoir, Alto Sorocaba basin (SP), Brazil

Considering the great importance of the Itupararanga Reservoir, Upper Alto Sorocaba basin/SP, this study aimed to report the variations of some parameters of water quality in the spatial and temporal gradients in this multipurpose res- ervoir. The eutrophication of this reservoir was checked using the Carlson Index Modified and the results indicate that the surface water were classified as eutrophic and mesotrophic in wet and dry periods, being characterized the better quality of water in wet period. In the vertical gradient the results showed a stratiphication in all parameters analyzed, except for the electrical conductivity, with good correlation between total phosphorous and chlorophyll-a, indicating that eutrophication of the reservoir changes the conditions of algal growth, mainly in its initial area. Immediate inter- ventions are needed, which must be directed to planning of land use, domestic effluents treatment, taking to an inte- grated management of this important watershed located in the São Paulo State.

Book Review of Determining the Economic Value of Water: Concepts and Methods by Robert A. YoungBook Review of Determining the Economic Value of Water: Concepts and Methods by Robert A. Young

Water has been and will continue to be a contentious issue for policy makers, landowners, municipalities, environmentalists, and citizens who feels they have an undeniable right to clean water delivered to their homes (at least in the United States). With so many groups coming into conflict over what, at least in the West and the Great Plains, continues to be a diminishing resource per capita, an understanding of the economic value of this resource is critical. It is important to note, as Robert Young does throughout his book, that the true economic value of water goes beyond what we pay our city services each month, or the cost to farmers or ranchers for pumping and distributing that water on their land. The value of water must take into account the value of the competing uses which are sometimes difficult to price.

Distribution of Rain Gardens in Lincoln Nebraska: Are Rain Gardens more Likely to be Built Near Bodies of Water

Abstract Rain gardens are an important tool in reducing the amount of stormwater runoff and accompanying pollutants from entering the city’s streams and lakes, and reducing their water quality. This thesis project analyzed the number of rain gardens installed through the City of Lincoln Nebraska Watershed Management’s Rain Garden Water Quality Project in distance intervals of one-eighth mile from streams and lakes. This data shows the distribution of these rain gardens in relation to streams and lakes and attempts to determine if proximity to streams and lakes is a factor in homeowners installing rain gardens. ArcGIS was used to create a map with layers to determine the number of houses with rain gardens in 1/8 mile distance increments from the city’s streams and lakes and their distances from a stream or lake. The total area, number of house parcels, and the type and location of each parcel type were also determined for comparison between the distance interval increments. The study revealed that fifty-eight percent of rain gardens were installed within a quarter mile of a stream or lake (an area covering 60% of the city and including 58.5% of the city’s house parcels), and that eighty percent of rain gardens were installed within three-eighth mile of streams or lakes (an area covering 75% of the city and 78.5% of the city’s house parcels). All parcels in the city are within 1 mile of a stream or lake. Alone the number of project houses per distance intervals suggested that proximity to a stream or lake was a factor in people’s decisions to install rain gardens. However, when compared to the number of house parcels available, proximity disappears as a factor in project participation.

Effects of water flow on ablation rate and morphological changes in human enamel and dentin after Er:YAG laser irradiation

Purpose: To investigate the laboratory effect of Er:YAG laser on ablation rate and morphological changes in human enamel and dentin with varying water flow. Methods: 23 human third molars were sectioned in mesio-distal and buccal-lingual directions. The slabs were flattened and weighted on an analytical laboratory balance (control). A 4-mm(2) area was demarcated and the samples were randomly assigned into three groups according to water flow employed during the laser irradiation (1.0, 1.5, and 2.0 mL/minute). An Er:YAG laser was used to ablate enamel (80.22-J/cm(2), 300 mJ/4Hz) and dentin (96.26-J/cm(2), 250 mJ/4Hz). After irradiation, the samples were immersed in distilled water for 1 hour and then weighted again. The final mass was obtained and laser-irradiated substrate mass loss was calculated by the difference between the initial and final mass. Afterwards, specimens were prepared for SEM. Results: Data were submitted to ANOVA and Tukey's test (P< 0.05). It was observed that the 2.0 mL/minute resulted in a higher mass loss, 1.0 mL/minute showed a lower mass loss, and 1.5 mL/minute demonstrated intermediate results (P< 0.05). The increase of water flow promoted less melting areas and cracks. Furthermore, dentin was more ablated than enamel. It may be concluded that the water flow of Er:YAG laser and the substrates affected the ablation rate. Among the tested parameters, 2.0 mL/minute improved the ability of ablation in enamel and dentin, with less morphologic surface alteration. (Am J Dent 20 12;25:332-336).

Coordination of water to organolead(IV) nitrates: The examples of [PbPh2(NO3)(2)(H2O)(2)] and [PbMe3(NO3)(H2O)]

The compound [PbPh2(NO3)(2)(H2O)(2)] was synthesized and characterized by spectroscopic methods (IR; H-1, C-13 and Pb-207 NMR) and mass spectrometry. An X-ray diffraction study showed that the crystal is a supramolecular tridimensional network of hydrogen-bonded PbPh2(NO3)(2)(H2O)(2) units in which the Pb atom is octacoordinated and adopts a distorted hexagonal bipyramidal geometry, with four O (bidentate nitrate) and two O (water) atoms in equatorial positions and two C-phenyl atoms in axial positions. The crystal of [PbMe3(NO3)(H2O)], obtained as a byproduct in the synthesis of PbMe2(NO3)(2), contains chains of hydrogen-bonded PbMe3(NO3)(H2O) units in which the Pb atom is pentacoordinated with a slightly distorted trigonal bipyramidal environment. In this arrangement the three C-methyl atoms are equatorial and the O atoms from the monodentate nitrate and the water molecule are axial. (C) 2011 Elsevier Ltd. All rights reserved.

Herbicides in the upper Poxim River, Sergipe, and the risk of contamination of water resources

Increased agricultural activity in watershed areas has been causing concern over contamination by herbicides in agricultural areas. The problem becomes more important when contamination can affect water for human consumption, as happens with water from the Poxim river, which supplies the city of Aracaju, capital of the State of Sergipe. The aim of this study was to evaluate the risk of contamination by herbicides to both surface and groundwater in the upper sub-basin of the Poxim River, and to detect the presence of the active ingredients Diuron and Ametrine up-river from the sugar-cane plantations. Risk analysis was carried out using criteria from the Environmental Protection Agency (EPA), the GUS index, and the GOSS method. It was observed that several active ingredients are at risk of leaching, demonstrating the importance of monitoring the river to control both the quality of water and the frequency and volume of herbicides used in the region. Based on the results, monitoring was carried out bi-monthly from July 2009 to July 2010 at two sampling points. Water samples were analyzed in the laboratory, where the presence of Diuron and Ametrine was noted. Water quality in the Sub-basin of the Rio Poxim is being influenced by the use of herbicides in the region. There was an increase in herbicide concentration in the surface water during the rainy season, possibly caused by soil runoff.

Electronic Properties of Water in Liquid Environment. A Sequential QM/MM Study Using the Free Energy Gradient Method

There is a continuous search for theoretical methods that are able to describe the effects of the liquid environment on molecular systems. Different methods emphasize different aspects, and the treatment of both the local and bulk properties is still a great challenge. In this work, the electronic properties of a water molecule in liquid environment is studied by performing a relaxation of the geometry and electronic distribution using the free energy gradient method. This is made using a series of steps in each of which we run a purely molecular mechanical (MM) Monte Carlo Metropolis simulation of liquid water and subsequently perform a quantum mechanical/molecular mechanical (QM/MM) calculation of the ensemble averages of the charge distribution, atomic forces, and second derivatives. The MP2/aug-cc-pV5Z level is used to describe the electronic properties of the QM water. B3LYP with specially designed basis functions are used for the magnetic properties. Very good agreement is found for the local properties of water, such as geometry, vibrational frequencies, dipole moment, dipole polarizability, chemical shift, and spin-spin coupling constants. The very good performance of the free energy method combined with a QM/MM approach along with the possible limitations are briefly discussed.

Toward supramolecular architectures of the anti-HIV drug lamivudine: understanding the effect of the inclusion of water in a hydrochloride form

Two salts of the anti-HIV drug lamivudine, namely, lamivudine hydrochloride and lamivudine hydrochloride monohydrate, were prepared for the first time. Structural relationships and the role of water in crystal assembly and lamivudine conformation were established and allowed for a rational approach to understand how solid state properties could be changed by engineering new salts of the drug.

Kinetic of water diffusion and color stability of a resin composite as a function of the curing tip distance

The influence of curing tip distance and storage time in the kinetics of water diffusion (water sorption-W SP, solubility-W SB, and net water uptake) and color stability of a composite were evaluated. Composite samples were polymerized at different distances (5, 10, and 15 mm) and compared to a control group (0 mm). After desiccation, the specimens were stored in distilled water to evaluate the water diffusion over a 120-day period. Net water uptake was calculated (sum of WSP and WSB). The color stability after immersion in a grape juice was compared to distilled water. Data were submitted to three-way ANOVA/Tukey's test (α = 5%). The higher distances caused higher net water uptake (p < 0.05). The immersion in the juice caused significantly higher color change as a function of curing tip distance and the time (p < 0.05). The distance of photoactivation and storage time provide the color alteration and increased net water uptake of the resin composite tested.

Atomistic Study of Water Confined in Silica.

In this work, we have used a combined of atomistic simulation methods to explore the effects of confinement of water molecules between silica surfaces. Firstly, the mechanical properties of water severe confined (~3A) between two silica alpha-quartz was determined based on first principles calculations within the density functional theory (DFT). Simulated annealing methods were employed due to the complex potential energry surface, and the difficulties to avoid local minima. Our results suggest that much of the stiffness of the material (46%) remains, even after the insertion of a water monolayer in the silica. Secondly, in order to access typical time scales for confined systems, classical molecular dynamics was used to determine the dynamical properties of water confined in silica cylindrical pores, with diameters varying from 10 to 40A. in this case we have varied the passivation of the silica surface, from 13% to 100% of SiOH, and the other terminations being SiOH2 and SiOH3, the distribution of the different terminations was obtained with a Monte Carlo simulation. The simulations indicates a lowering of the diffusion coefficientes as the diameter decreases, due to the structuration of hydrogen bonds of water molecules; we have also obtained the density profiles of the confined water and the interfacial tension.

Distribution of water masses and diapycnal mixing in the Cape Verde Frontal Zone

[EN]The Cape Verde Frontal Zone separates North and South Atlantic Central Waters in the eastern North Atlantic Subtropical Gyre. CTD-O2 and shipboard ADCP data from three hydrographic sections carried out in September 2003 are used to study the structure of the front. Results show the relation between spatial variations of water masses and currents, demonstrating the importance of advection in the distribution of water masses. Diapycnal diffusivities due to double diffusion and vertical shear instabilities are also estimated. Existence of competition between the two processes through the water column is shown. Depth-averaged diffusivities suggest that salt fingering dominates diapycnal mixing, except areas of purest South Atlantic Central Water. Here, double diffusion processes are weak and, consequently, shear of the flow is the main process. Results also show that strong mixing induced by vertical shear is associated with a large intrusion found near the front.

Photoreactive polyorganosiloxane nanoparticles and the fabrication of photocleavable microcapsules

In this thesis, we have presented the preparation of highly crosslinked spherical photoreactive colloidal particles of radius about 10 nm based on the monomer trimethoxysilane. These particles are labeled chemically with two different dye systems (coumarin, cinnamate) which are known to show reversible photodimerization. By analyzing the change in particle size upon UV irradiation with dynamic light scattering, we could demonstrate that the partially reversible photoreaction in principle can be utilized to control increase and decrease of colloidal clusters. Here, selection of the appropriate wavelengths during the irradiation employing suitable optical filters proved to be very important. Next, we showed how photocrosslinking of our nanoparticles within the micrometer-sized thin oil shell of water-oil-water emulsion droplets leads to a new species of optically addressable microcontainers. The inner water droplet of these emulsions may contain drugs, dyes or other water-soluble components, leading to filled containers. Thickness, mechanical stability and light resistance of the container walls can be controlled in a simple way by the amount and adjustable photoreactivity (= No. of labels/particle) of the nanoparticles. Importantly, the chemical bonds between the nanoparticles constituting the microcapsule shell can be cleaved photochemically by irradiation with uv light. An additional major advantage is that filling our microcapsules with water-soluble substrate molecules is extremely simple using a solution of the guest molecules as inner water phase of the W/O/W-emulsion. This optically controlled destruction of our microcontainers thus opens up a pathway to controlled release of the enclosed components as illustrated by the example of enclosed cyclodextrin molecules.

The Influence of Fractures on Vulnerability to Pollution of a Carbonate Aquifer: Monte Conero (Italy)

The carbonate outcrops of the anticline of Monte Conero (Italy) were studied in order to characterize the geometry of the fractures and to establish their influence on the petrophysical properties (hydraulic conductivity) and on the vulnerability to pollution. The outcrops form an analog for a fractured aquifer and belong to the Maiolica Fm. and the Scaglia Rossa Fm. The geometrical properties of fractures such as orientation, length, spacing and aperture were collected and statistically analyzed. Five types of mechanical fractures were observed: veins, joints, stylolites, breccias and faults. The types of fractures are arranged in different sets and geometric assemblages which form fracture networks. In addition, the fractures were analyzed at the microscale using thin sections. The fracture age-relationships resulted similar to those observed at the outcrop scale, indicating that at least three geological episodes have occurred in Monte Conero. A conceptual model for fault development was based on the observations of veins and stylolites. The fracture sets were modelled by the code FracSim3D to generate fracture network models. The permeability of a breccia zone was estimated at microscale by and point counting and binary image methods, whereas at the outcrop scale with Oda’s method. Microstructure analysis revealed that only faults and breccias are potential pathways for fluid flow since all veins observed are filled with calcite. According this, three scenarios were designed to asses the vulnerability to pollution of the analogue aquifer: the first scenario considers the Monte Conero without fractures, second scenario with all observed systematic fractures and the third scenario with open veins, joints and faults/breccias. The fractures influence the carbonate aquifer by increasing its porosity and hydraulic conductivity. The vulnerability to pollution depends also on the presence of karst zones, detric zones and the material of the vadose zone.