Kattilalaitosten järjestelmällinen suunnittelu ja modulaarinen rakenne

Tämän diplomityön tavoitteena on tutkia kattilalaitosten järjestelmällistä suunnittelua, huomioiden laitoksen elinkaariprosessit ja modulaarinen tuoterakenne. Kattilalaitokset investointituotteina toteutetaan tyypillisesti projektitoimintamallilla, jolloin jokainen toimitus suunnitellaan alusta kyseisen kohteen vaatimusten perusteella. Päätöksenteon peruste on laitosasiakkaiden osalta tyypillisesti hinta, jonkavuoksi laitoksen perusratkaisut tulee olla ennalta määriteltyjä ja toimitusprosessi huolellisesti suunniteltu, jotta kustannukset ja aikataulu ovat ennustettavissa. Projektitoimituksissa projektipäälliköllä on merkittävä vastuu myös suunnittelun onnistumisesta ja käytössä olevat projektinhallintamallit ovat hyvin tuotekeskeisiä, jolloin vaatimuksia ei riittävästi huomioida ja siten toteutettu laitosratkaisu ei täytä usein sidosryhmien asettamia vaatimuksia. Monimutkaisten järjestelmien kehittämiseen ja suunnitteluun on olemassa Systems Engineering - suunnittelumalli, jonka hyödyntäminen energiatekniikan alalla on ollut vielä vähäistä. Malli tarjoaa yhdessä ISO/ICE 15288 standardin kanssa valmiit prosessit tuotteen järjestelmälliselle suunnittelulle. Modulaariset tuoterakenteet ovat olleet perusvaatimus komponenttien toimitusten osalta, mutta laitosjärjestelmien tuotteistaminen on koettu vaikeaksi runsaan räätälöintitarpeen takia. Prosessimaisella toimintamallilla voidaan tuottaa modulaarisia tuoterakenteita ja tehostaa kattilalaitosten muutosten hallintaa. Tutkimuksessa tunnistettiin tyypilliset kattilalaitoksen suunnittelun prosessit kattilalaitosten kokonaistoimituksiin erikoistuneelle KPA Unicon Oy:lle.

Optimisation of the lipase-catalysed preparation of a nucleoside prodrug model using an experimental design methodology

The preparation of 2', 3'-di-O-hexanoyluridine (2) by a Candida antarctica B lipase-catalysed alcoholysis of 2', 3', 5'-tri-O-hexanoyluridine (1) was optimised using an experimental design. At 25 ºC better experimental conditions allowed an increase in the yield of 2 from 80% to 96%. In addition to the yield improvement, the volume reaction could be diminished in a factor of 5 and the reaction time significantly shortened.

IT architecture for category driven corporate procurement measurement

The purpose of this thesis was to investigate creating and improving category purchasing visibility for corporate procurement by utilizing financial information. This thesis was a part of the global category driven spend analysis project of Konecranes Plc. While creating general understanding for building category driven corporate spend visibility, the IT architecture and needed purchasing parameters for spend analysis were described. In the case part of the study three manufacturing plants of Konecranes Standard Lifting, Heavy Lifting and Services business areas were examined. This included investigating the operative IT system architecture and needed processes for building corporate spend visibility. The key findings of this study were the identification of the needed processes for gathering purchasing data elements while creating corporate spend visibility in fragmented source system environment. As an outcome of the study, roadmap presenting further development areas was introduced for Konecranes.

Comparison of a deterministic and a data driven model to describe MBR fouling

Membrane bioreactors (MBRs) are a combination of activated sludge bioreactors and membrane filtration, enabling high quality effluent with a small footprint. However, they can be beset by fouling, which causes an increase in transmembrane pressure (TMP). Modelling and simulation of changes in TMP could be useful to describe fouling through the identification of the most relevant operating conditions. Using experimental data from a MBR pilot plant operated for 462days, two different models were developed: a deterministic model using activated sludge model n°2d (ASM2d) for the biological component and a resistance in-series model for the filtration component as well as a data-driven model based on multivariable regressions. Once validated, these models were used to describe membrane fouling (as changes in TMP over time) under different operating conditions. The deterministic model performed better at higher temperatures (>20°C), constant operating conditions (DO set-point, membrane air-flow, pH and ORP), and high mixed liquor suspended solids (>6.9gL-1) and flux changes. At low pH (<7) or periods with higher pH changes, the data-driven model was more accurate. Changes in the DO set-point of the aerobic reactor that affected the TMP were also better described by the data-driven model. By combining the use of both models, a better description of fouling can be achieved under different operating conditions

Study of ligand-based virtual screening tools in computer-aided drug design

Virtual screening is a central technique in drug discovery today. Millions of molecules can be tested in silico with the aim to only select the most promising and test them experimentally. The topic of this thesis is ligand-based virtual screening tools which take existing active molecules as starting point for finding new drug candidates. One goal of this thesis was to build a model that gives the probability that two molecules are biologically similar as function of one or more chemical similarity scores. Another important goal was to evaluate how well different ligand-based virtual screening tools are able to distinguish active molecules from inactives. One more criterion set for the virtual screening tools was their applicability in scaffold-hopping, i.e. finding new active chemotypes. In the first part of the work, a link was defined between the abstract chemical similarity score given by a screening tool and the probability that the two molecules are biologically similar. These results help to decide objectively which virtual screening hits to test experimentally. The work also resulted in a new type of data fusion method when using two or more tools. In the second part, five ligand-based virtual screening tools were evaluated and their performance was found to be generally poor. Three reasons for this were proposed: false negatives in the benchmark sets, active molecules that do not share the binding mode, and activity cliffs. In the third part of the study, a novel visualization and quantification method is presented for evaluation of the scaffold-hopping ability of virtual screening tools.

Modeling and developing a customer-oriented configuration process in a mass customization environment

In this thesis the main objective is to examine and model configuration system and related processes. When and where configuration information is created in product development process and how it is utilized in order-delivery process? These two processes are the essential part of the whole configuration system from the information point of view. Empirical part of the work was done as a constructive research inside a company that follows a mass customization approach. Data models and documentation are created for different development stages of the configuration system. A base data model already existed for new structures and relations between these structures. This model was used as the basis for the later data modeling work. Data models include different data structures, their key objects and attributes, and relations between. Representation of configuration rules for the to-be configuration system was defined as one of the key focus point. Further, it is examined how the customer needs and requirements information can be integrated into the product development process. Requirements hierarchy and classification system is presented. It is shown how individual requirement specifications can be connected for physical design structure via features by developing the existing base data model further.

IPTV-palvelun pilotointi

Diplomityössä kehitettiin teleoperaattorille IPTV-palvelu (Internet Protocol Television) tietyillä rajatuilla ominaisuuksilla, kehitettiin IPTV-palvelulle uusi käyttöliittymä ja pilotoitiin uutta palvelua. Pilotoinnin tarkoituksena oli saada kokemusta uudentyyppisten tv-palvelujen käyttöönotosta. Pilotoinnin lopuksi koottiin pilottikäyttäjiltä saatu palaute ja analysoitiin palvelua sen perusteella. Työn taustatieto-osuudessa määritellään IPTV ja siihen tyypillisimmin kuuluvat palvelut. Lisäksi selvitetään, millaisia ovat IPTV:ssä käytetyt tekniikat ja verkkoarkkitehtuuri. Taustatiedoissa esitellään myös palvelun käyttäjän kokeman laadun parametrit ja kerrosmalli. Samalla tuodaan esiin menetelmät erityisesti kuvanlaadun ja käytettävyyden parantamiseksi. Opittavuus ja helppokäyttöisyys sekä viihteellisyys ja miellyttävyys on tunnistettu tärkeimmiksi käytettävyyden osa-alueiksi elinkaarensa alkupäässä olevissa IPTV-palveluissa. Diplomityön toteutusosuudessa esitetään työn lähtökohtana ollut vaatimusmäärittely ja sen vaikutus työn rajaukseen. Tämän jälkeen esitellään kehitetyn IPTV-palvelun ominaisuudet, joista tärkeimpinä tuodaan esiin tallennus- ja ajansiirtotoiminnot. Toteutusosuudessa selvitetään myös teleoperaattorin IPTV-verkon rakenne ja toiminta. Seuraavaksi käydään läpi alkuperäisestä käyttöliittymästä tehty analyysi ja analyysin perusteella toteutettu uusi käyttöliittymä, jossa merkittävimmät parannukset on tehty navigaatiorakenteeseen. Lopuksi selvitetään pilotoinnista kerätyt tulokset. Tuloksien perusteella voidaan nähdä, että ajansiirtotoiminnot riittävät takaamaan palvelun omaksumisen, mutta uudet toiminnot vaativat riittävän opastuksen. Tulokset osoittavat myös, että palvelun käytettävyys uudella käyttöliittymällä on tavoitetasolla, vaikkakin toimintojen viiveet heikentävät käyttökokemuksen miellyttävyyttä.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

On the impact of rigorous approaches on the quality of development

Software systems are expanding and becoming increasingly present in everyday activities. The constantly evolving society demands that they deliver more functionality, are easy to use and work as expected. All these challenges increase the size and complexity of a system. People may not be aware of a presence of a software system, until it malfunctions or even fails to perform. The concept of being able to depend on the software is particularly significant when it comes to the critical systems. At this point quality of a system is regarded as an essential issue, since any deficiencies may lead to considerable money loss or life endangerment. Traditional development methods may not ensure a sufficiently high level of quality. Formal methods, on the other hand, allow us to achieve a high level of rigour and can be applied to develop a complete system or only a critical part of it. Such techniques, applied during system development starting at early design stages, increase the likelihood of obtaining a system that works as required. However, formal methods are sometimes considered difficult to utilise in traditional developments. Therefore, it is important to make them more accessible and reduce the gap between the formal and traditional development methods. This thesis explores the usability of rigorous approaches by giving an insight into formal designs with the use of graphical notation. The understandability of formal modelling is increased due to a compact representation of the development and related design decisions. The central objective of the thesis is to investigate the impact that rigorous approaches have on quality of developments. This means that it is necessary to establish certain techniques for evaluation of rigorous developments. Since we are studying various development settings and methods, specific measurement plans and a set of metrics need to be created for each setting. Our goal is to provide methods for collecting data and record evidence of the applicability of rigorous approaches. This would support the organisations in making decisions about integration of formal methods into their development processes. It is important to control the software development, especially in its initial stages. Therefore, we focus on the specification and modelling phases, as well as related artefacts, e.g. models. These have significant influence on the quality of a final system. Since application of formal methods may increase the complexity of a system, it may impact its maintainability, and thus quality. Our goal is to leverage quality of a system via metrics and measurements, as well as generic refinement patterns, which are applied to a model and a specification. We argue that they can facilitate the process of creating software systems, by e.g. controlling complexity and providing the modelling guidelines. Moreover, we find them as additional mechanisms for quality control and improvement, also for rigorous approaches. The main contribution of this thesis is to provide the metrics and measurements that help in assessing the impact of rigorous approaches on developments. We establish the techniques for the evaluation of certain aspects of quality, which are based on structural, syntactical and process related characteristics of an early-stage development artefacts, i.e. specifications and models. The presented approaches are applied to various case studies. The results of the investigation are juxtaposed with the perception of domain experts. It is our aspiration to promote measurements as an indispensable part of quality control process and a strategy towards the quality improvement.

Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Model-View-Controller architectural pattern and its evolution in graphical user interface frameworks

Model-View-Controller (MVC) is an architectural pattern used in software development for graphical user interfaces. It was one of the first proposed solutions in the late 1970s to the Smart UI anti-pattern, which refers to the act of writing all domain logic into a user interface. The original MVC pattern has since evolved in multiple directions, with various names and may confuse many. The goal of this thesis is to present the origin of the MVC pattern and how it has changed over time. Software architecture in general and the MVC’s evolution within web applications are not the primary focus. Fundamen- tal designs are abstracted, and then used to examine the more recent versions. Prob- lems with the subject and its terminology are also presented.

Microbusiness: A new social business model to alleviate poverty in developing countries?

Poverty alleviation views have shifted from seeing the poor as victims or as potential consumers, to seeing them as gainers. Social businesses include microfinancing and microfranchising, which engage people at the bottom of the pyramid using business instead of charity. There are, however, social business firms that do not fit to the existing social business model theory. These firms provide markets to poor producers and mix traditional, local craftsmanship with western design. Social business models evolve faster than the academic literature can study them. This study contributes to filling this gap. The purpose of this Master’s thesis is to develop the concept of social business as poverty alleviation method in developing countries. It also aims; 1) to describe the means for poverty alleviation in developing countries; 2) to introduce microbusiness as a social business model; and 3) to examine the challenges of microbusinesses. Qualitative case study is used as a research strategy and theme interviews as a data collecting method. The empirical data is gathered from four interviews of Finnish or Finnish-owned firms that employ microbusiness – Mifuko, Tensira, Mangomaa and Tikau – and this is supported with secondary data including articles on case companies. The results show that microbusiness is a valid new social business model that aims at poverty alleviation by engaging the poor at the bottom of the pyramid. It is possible to map the value proposition, value constellation, and economic and social profit equations of the case firms. Two major types of firms emerge from the results; the first consists of design-oriented firms that emphasize the quality and design of the products, and the second consists of bazaar-like firms whose product portfolio is less sophisticated and who promote more the stories of the products – not the design. All microbusiness firms provide markets, promote traditional handicrafts, form close relationships to their producers, and aim at enhancing lives through their businesses. The attitudes towards social businesses are sometimes negative, but this is changing for the better. In conclusion, microbusiness answers to two different needs at the same time – consumers’ needs for ethical products and the social needs of the producers – but the social need is the ultimate reason why the entrepreneurs started business. Microbusiness continues as a poverty alleviation tool that sees the poor as gainers; by providing them steady employment, microbusiness increases the poor’s self-esteem and enables them for a better living. Academic literature has not been able to offer enough alternative business models to cover all social businesses; the current study contributes to this by concluding that microbusiness is another social business model.

Ecosystem architecture design: endogenous and exogenous structural properties

The aim of this dissertation is to bridge and synthesize the different streams of literature addressing ecosystem architecture through a multiple‐lens perspective. In addition, the structural properties of and processes to design and manage the architecture will be examined. With this approach, the oft‐neglected actor‐structure duality is addressed and both the position and structure, and action and process are under scrutiny. Further, the developed framework and empirical evidence offer valuable insights on how firms collectively create value and individually appropriate value. The dissertation is divided into two parts. The first part comprises a literature review, as well as the conclusions of the whole study, and the second part includes six research publications. The dissertation is based on three different reasoning logics: abduction, induction and deduction; related qualitative and quantitative methodologies are utilized in the empirical examination of the phenomenon in the information and communication technology industry. The results suggest firstly that there are endogenous and exogenous structural properties of the ecosystem architecture. Out of these, the former ones can be more easily influenced by a particular actor whereas the latter ones are taken more or less for granted. Secondly, the exogenous ecosystem design properties influence the value creation potential of the ecosystem whereas the endogenous ecosystem design properties influence the value appropriation potential of a particular actor in the ecosystem. Thirdly, the study suggests that there is a relationship between endogenous and exogenous structural properties in that the endogenous properties can be leveraged to create and reconfigure the exogenous properties whereas the exogenous properties prose opportunities and restrictions on the use of endogenous properties. In addition, the study suggests that there are different emergent and engineered processes to design and manage ecosystem architecture and to influence both the endogenous and exogenous structural properties of ecosystem architecture. This study makes three main contributions. First, on the conceptual level, it brings coherence and direction to the fast growing body of literature on novel inter‐organizational arrangements, such as ecosystems. It does this by bridging and synthetizing three different streams of literature, namely the boundary, design and orchestration conception. Secondly, it sets out a framework that enhances our understanding of the structural properties of ecosystem architecture; of the processes to design and manage ecosystem architecture; and of their influence on the value creation potential of the ecosystem and the value capture potential of a particular firm. Thirdly, it offers empirical evidence of the structural properties and processes.

Creating an open-books implementation framework for a maintenance-related value-based life-cycle model

This study is a qualitative action research by its nature with elements of personal design in the form of a tangible model implementation framework construction. Utilized empirical data has been gathered via two questionnaires in relation to the arranged four workshop events with twelve individual participants. Five of them represented maintenance customers, three maintenance service providers and four equipment providers respectively. Further, there are two main research objectives in proportion to the two complementary focusing areas of this thesis. Firstly, the value-based life-cycle model, which first version has already been developed prior to this thesis, requires updating in order to increase its real-life applicability as an inter-firm decision-making tool in industrial maintenance. This first research objective is fulfilled by improving appearance, intelligibility and usability of the above-mentioned model. In addition, certain new features are also added. The workshop participants from the collaborating companies were reasonably pleased with made changes, although further attention will be required in future on the model’s intelligibility in particular as main results, charts and values were all reckoned as slightly hard to understand. Moreover, upgraded model’s appearance and added new features satisfied them the most. Secondly and more importantly, the premises of the model’s possible inter-firm implementation process need to be considered. This second research objective is delivered in two consecutive steps. At first, a bipartite open-books supported implementation framework is created and its different characteristics discussed in theory. Afterwards, the prerequisites and the pitfalls of increasing inter-organizational information transparency are studied in empirical context. One of the main findings was that the organizations are not yet prepared for network-wide information disclosure as dyadic collaboration was favored instead. However, they would be willing to share information bilaterally at least. Another major result was that the present state of companies’ cost accounting systems will definitely need implementation-wise enhancing in future since accurate and sufficiently detailed maintenance data is not available. Further, it will also be crucial to create supporting and mutually agreed network infrastructure. There are hardly any collaborative models, methods or tools currently in usage. Lastly, the essential questions about mutual trust and predominant purchasing strategies are cooperation-wise important. If inter-organizational activities are expanded, a more relational approach should be favored in this regard. Mutual trust was also recognized as a significant cooperation factor, but it is hard to measure in reality.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.