930 resultados para fine particles, Positive Matrix Factorisation, receptor modelling


Relevância:

30.00% 30.00%

Publicador:

Resumo:

The research is aimed at contributing to the identification of reliable fully predictive Computational Fluid Dynamics (CFD) methods for the numerical simulation of equipment typically adopted in the chemical and process industries. The apparatuses selected for the investigation, specifically membrane modules, stirred vessels and fluidized beds, were characterized by a different and often complex fluid dynamic behaviour and in some cases the momentum transfer phenomena were coupled with mass transfer or multiphase interactions. Firs of all, a novel modelling approach based on CFD for the prediction of the gas separation process in membrane modules for hydrogen purification is developed. The reliability of the gas velocity field calculated numerically is assessed by comparison of the predictions with experimental velocity data collected by Particle Image Velocimetry, while the applicability of the model to properly predict the separation process under a wide range of operating conditions is assessed through a strict comparison with permeation experimental data. Then, the effect of numerical issues on the RANS-based predictions of single phase stirred tanks is analysed. The homogenisation process of a scalar tracer is also investigated and simulation results are compared to original passive tracer homogenisation curves determined with Planar Laser Induced Fluorescence. The capability of a CFD approach based on the solution of RANS equations is also investigated for describing the fluid dynamic characteristics of the dispersion of organics in water. Finally, an Eulerian-Eulerian fluid-dynamic model is used to simulate mono-disperse suspensions of Geldart A Group particles fluidized by a Newtonian incompressible fluid as well as binary segregating fluidized beds of particles differing in size and density. The results obtained under a number of different operating conditions are compared with literature experimental data and the effect of numerical uncertainties on axial segregation is also discussed.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Bei einer Risikoabschätzung bezüglich einer Gefährdung des Schutzgutes Grundwasser müssen alle relevanten Transportpfade, auf denen Schadstoffe durch die Bodenzone bis ins Grundwasser verlagert werden, identifiziert und quantifiziert werden. Die Verlagerung von Schadstoffen gebunden an mobile Partikel im Sickerwasser wird dabei oft vernachlässigt. In dieser Arbeit wurden sowohl experimentelle Untersuchungen zum Partikeltransport in der Bodenzone als auch Szenarienmodellierungen hinsichtlich der Wechselwirkung Partikel/Schadstoff durchgeführt. Die experimentellen ungesättigten Säulenversuche wurden unter naturnahen stationären und instationären hydraulischen und hydrochemischen Bedingungen durchgeführt. Dabei wurde der Einfluss der Parameter Durchmesser Bodenmatrix, Partikelgröße, Beregnungsintensität, Oberflächenspannung und Hydrochemie auf den Transport von natürlichen und synthetischen Partikeln untersucht. Des Weiteren wurden Untersuchungen zur partikelgebundenen Verlagerung von Phenanthren durchgeführt. In einer numerischen Szenarienmodellierung mit dem Modell SMART wurde untersucht, unter welchen Randbedingungen der Transport von Partikeln gleichzeitig zu signifikanten partikelgebundenen Schadstoffkonzentrationen im Grundwasser führt. Dabei wurden die Parameter Lithologie Partikel/Boden, Hydrophobizität Schadstoff, Partikelkonzentration, Partikeldurchmesser sowie Körnung Bodenmatrix variiert. Die Ergebnisse dieser Arbeit zeigen, dass der partikelgebundene Schadstofftransportpfad in der ungesättigten Bodenzone in verschiedenen Szenarien den Anteil mobiler Schadstoffe, die mit dem Sickerwasser ins Grundwasser gelangen, signifikant erhöht. Auf Basis der experimentellen und theoretischen Untersuchungen wurde ein zweistufiges Bewertungsschema entwickelt, das bereits im Vorfeld einer Risikoabschätzung als Entscheidungshilfe hinsichtlich der Relevanz einer Mobilisierung, eines Transports und des Rückhalts von partikelgebundenen Schadstoffen in der ungesättigten Zone dient.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Konditionale Modellsysteme zur Untersuchung der ERBB2-induzierten Tumorgenese Die Rezeptor-Tyrosinkinase ERBB2 ist in einer Vielzahl epithelialer Tumore, wie Mamma- und Ovarialkarzinomen, überexprimiert. Diese erhöhte Expression korreliert mit aggressivem Tumorwachstum, verstärkter Metastasierung und schlechter Prognose für den Patienten. Zur genaueren Untersuchung molekularer Mechanismen, die zur Tumorentstehung infolge der ERBB2-Überexpression führen, wurden im Rahmen dieser Arbeit mit Hilfe des Tet-Systems induzierbare MCF-7 Zelllinien generiert. Diese exprimieren bei Gabe von Doxyzyklin ERBB2 bzw. die zum humanen ERBB2 homologe und durch Punktmutation onkogen aktivierte Rattenvariante NeuT. Nachdem die stringente Regulierbarkeit durch Doxyzyklin für die untersuchten Zellklone gezeigt werden konnte, stellte sich bei der Charakterisierung der Zelllinien heraus, dass die Induktion von ERBB2 erstaunlicherweise nicht zur Proliferation der Zellen, sondern zum Wachstumsarrest führt. Bei der Untersuchung verschiedener Zellzyklusregulatoren konnte dieser Zellzyklusarrest dem CDK-Inhibitor P21 zugeordnet werden, dessen Expression durch ERBB2 induziert wird. In P21-Antisense-Experimenten konnte nachgewiesen werden, dass P21 eine Schlüsselrolle beim ERBB2-induzierten Zellzyklusarrest spielt. Neben der Induktion von P21 und der daraus resultierenden Wachstumsinhibition zeigten die Zellen starke morphologische Veränderungen und waren positiv beim Nachweis der Seneszenz-assoziierten -Galaktosidase. Erstmals konnte gezeigt werden, dass die Induktion des Onkogens ERBB2 nicht zur Proliferation, sondern zur Aktivierung eines verfrühten Seneszenz-Programms führt, welches der Zelle Schutz gegen die Onkogeneinwirkung bietet. Bei der Untersuchung verschiedener Signaltransduktionskaskaden mit Inhibitormolekülen konnte die Aktivierung dieses Seneszenz-Programms der Stress-aktivierten Proteinkinase P38 zugeordnet werden. Zur Identifizierung von Genen, die für die ERBB2-induzierte Tumorgenese relevant sind, wurde die differenzielle Genexpression eines NeuT-Klons nach 8- bzw. 48-stündiger Induktion mit Doxyzyklin in einem cDNA-Array untersucht. Dabei zeigte sich eine besonders starke Induktion von Integrin 5 und Integrin 1, die zusammen den Fibronektinrezeptor bilden. Der funktionale Nachweis des Rezeptors in einem Adhäsionsassay demonstrierte ein stark erhöhtes Adhäsionsverhalten ERBB2-überexprimierender Zellen an Fibronektin. Bei der Untersuchung von Mamma-, Ovarial- und Endometriumkarzinomen konnte die Expression von ERBB2 mit der von Integrin 5 korreliert werden. Diese Ergebnisse machen Integrin 5 zu einem potenziellen neuen Tumormarker und Therapieziel in ERBB2-überexprimierenden Tumoren. Ein weiteres interessantes Gen, das sich im Array durch ERBB2 überexprimiert zeigte, war die Matrix-Metalloproteinase MMP-9. In einem Zymografieassay konnte die erhöhte Gelatinaseaktivität von MMP-9 in Dox-induzierten Zellen nachgewiesen werden. Der Einsatz verschiedener Signaltransduktionsinhibitoren ergab, dass auch die ERBB2-induzierte Expression von MMP-9 über die Aktivierung von P38 läuft. Bei der Suche nach weiteren MMPs, die für die ERBB2-induzierte Tumorgenese relevant sein könnten, wurde MMP-13 untersucht. Erstmals konnte gezeigt werden, dass diese Matrix-Metalloproteinase von ERBB2 induziert wird. Dieser interessante Befund wurde auch in einem anderen Zellmodell in NIH3T3 Mausfibroblasten verifiziert. Durch ihre Matrix-degradierenden Eigenschaften sind MMPs potente „Werkzeuge“ für Tumorzellen und stellen ein wichtiges Ziel zur Unterbindung der Invasion und Metastasierung dieser Zellen dar. Neben den Zellkulturarbeiten wurden im Rahmen dieser Dissertation transgene Responder-Mäuse generiert, die NeuT unter Kontrolle eines Tet-responsiven Promotors exprimieren. Von vier transgenen Gründerlinien zeigten zwei eine unerwünschte, basale NeuT-Expression, für die beiden anderen Linien konnte sowohl in MEF-Assays, als auch nach Kreuzung mit rtTA- bzw. tTA-Effektor-Mäusen eine Dox-abhängige Regulation des Transgens gezeigt werden. Die Tiere dieser Linien sollen in Zukunft mit Effektor-Mäusen gepaart werden, die den rtTA bzw. tTA spezifisch in für die ERBB2-Tumorgenese relevanten Geweben, wie Ovarial- oder Lungenepithelzellen, exprimieren. So können individuelle Tumormodelle für die verschiedenen epithelialen Tumore, bei denen die Überexpression von ERBB2 von Bedeutung ist, entwickelt und untersucht werden.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

In this work we develop and analyze an adaptive numerical scheme for simulating a class of macroscopic semiconductor models. At first the numerical modelling of semiconductors is reviewed in order to classify the Energy-Transport models for semiconductors that are later simulated in 2D. In this class of models the flow of charged particles, that are negatively charged electrons and so-called holes, which are quasi-particles of positive charge, as well as their energy distributions are described by a coupled system of nonlinear partial differential equations. A considerable difficulty in simulating these convection-dominated equations is posed by the nonlinear coupling as well as due to the fact that the local phenomena such as "hot electron effects" are only partially assessable through the given data. The primary variables that are used in the simulations are the particle density and the particle energy density. The user of these simulations is mostly interested in the current flow through parts of the domain boundary - the contacts. The numerical method considered here utilizes mixed finite-elements as trial functions for the discrete solution. The continuous discretization of the normal fluxes is the most important property of this discretization from the users perspective. It will be proven that under certain assumptions on the triangulation the particle density remains positive in the iterative solution algorithm. Connected to this result an a priori error estimate for the discrete solution of linear convection-diffusion equations is derived. The local charge transport phenomena will be resolved by an adaptive algorithm, which is based on a posteriori error estimators. At that stage a comparison of different estimations is performed. Additionally a method to effectively estimate the error in local quantities derived from the solution, so-called "functional outputs", is developed by transferring the dual weighted residual method to mixed finite elements. For a model problem we present how this method can deliver promising results even when standard error estimator fail completely to reduce the error in an iterative mesh refinement process.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Polystyrene latex particles modified at the surface with different hydrophilic functional groups were prepared by miniemulsion polymerization and applied to control the crystallization of zinc oxide in aqueous medium. The effects of both latex structure and concentration on the crystal growth, morphology, crystalline structure, and properties of the resulting zinc oxide were analyzed. Depending on the latex additive used, micro- and submicrosized crystals with a broad variety of morphologies were obtained. Among the studied latexes, the carboxyl-derived particles were shown to be a convenient system for further quantitative investigations. In this case, as the additive concentration increases, the aspect ratio of the crystals decreases systematically. Latex particles are assumed to adsorb preferentially onto the fast growing {001} faces of ZnO, interacting with the growth centers and reducing the growth rate in [001]. When zinc oxide is precipitated in the presence of latex, the polymer particles become incorporated into the growing crystals and polymer–inorganic hybrid materials are obtained. These materials are composed of an inorganic and largely undisturbed crystalline matrix in which organic latex particles are embedded. Increasing amounts of latex become incorporated into the growing crystals at increasing overall concentration in the crystallizing system. Photoluminescence (PL) spectra were measured to obtain information on defect centers. Emission spectra of all samples showed a narrow UV peak and a broad band in the green-yellow spectral region. The former emission is attributed to exciton recombination, whereas the latter seems to be related with deep-level donors. Latex appears to be a quencher of the visible emission of zinc oxide. Thus, compared to pure zincite, ZnO–latex hybrid materials show a significantly lower PL intensity in the visible range of the spectrum. Under continuous photoexcitation, a noticeable dynamic behavior of the PL is observed, which can be related to a photodesorption of adsorbed oxygen. These surface-adsorbed oxygen species seem to play a crucial role for the optical properties of the materials and may mediate the tunneling of electrons from the conduction band to preexisting deep-level traps, probably related to intrinsic defects (oxygen vacancies or interstitial zinc). The polymer particles can block the sites where oxygen adsorbs, and the disappearance of the “electron-shuttle” species leads to the observed quenching of the visible emission. Electron paramagnetic resonance (EPR) provided additional information about crystal defects with unpaired electrons. Spectra of all samples exhibit a single signal at g ≈ 1.96, typical for shallow donors. Contrary to the results of other authors, no correlation was possible between the EPR signal and the visible range of PL spectra, which suggests that centers responsible for the visible emission and the EPR signal are different.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

La diagnosi di linfoma non Hodgkin B della zona marginale si basa su criteri morfologici e sulla sostanziale negatività per marcatori immunoistochimici espressi in altri sottotipi di linfoma B. L’ obiettivo di questo lavoro è stato, quindi, quello di ricercare una molecola specifica associata ai linfomi della zona marginale. Materiali e Metodi. Sono stati esaminati 2.104 linfomi periferici di entità nosologia eterogenea mediante un anticorpo monoclonale, diretto contro la molecola IRTA1, che riconosce la zona marginale nei tessuti linfoidi umani. Risultati. Si è riscontrata espressione di IRTA1 nel 93% dei linfomi della zona marginale ad insorgenza extranodale e nel 74% di quelli primitivi linfonodali suggerendo la possibilità che questi linfomi possano originare dalle cellule perifollicolari o monocitoidi IRTA1+ riscontrabili nei linfonodi reattivi. La valutazione immunoistochimica mediante doppia colorazione (IRTA1/bcl6), ha inoltre dimostrato come vi sia una modulazione fenotipica nelle cellule marginali neoplastiche nel momento in cui esse colonizzano i follicoli linfoidi e durante la loro circolazione nei centri germinativi. Le cellule marginali neoplastiche che differenziano in senso plasmacellulare perdono l’ espressione di IRTA1 Discussione. In conclusione, tali evidenze hanno permesso di ampliare la conoscenza sulla biologia dei linfomi marginali e sottolineano come IRTA1 sia il primo marcatore diagnostico positivo per queste neoplasie.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Das Ziel dieser Arbeit besteht darin, die Möglichkeiten der Sprühtrocknung für die Generierung von Inhalationspulvern zur Therapie von Lungenkrankheiten zu nutzen. Die Erzeugung von physikalisch stabilen und leicht dispergierbaren Partikeln steht hierbei im Vordergrund. Aufgrund von physiko-chemischen Untersuchungen (Glasübergangstemperatur, Fragilität, Relaxationsverhalten, Hygroskopizität) unterschiedlicher amorpher Hilfsstoffe (Lactose, Raffinose, Dextrane, Cyclodextrine) ist für Hydroxypropyl-β-Cyclodextrin das größte Potential für die Stabilisierung eines Wirkstoffes innerhalb einer amorphen Matrix erkennbar. Sprühgetrocknete Partikel weisen im Vergleich zu strahlgemahlenen Partikeln günstigere Dispergier- und Depositionseigenschaften auf. Dies ist vorrangig auf größere Berührungsflächen zwischen strahlgemahlenen Partikeln zurückzuführen. Kugelförmige sprühgetrocknete Partikel besitzen dagegen aufgrund einer punktförmigen Berührung geringere Haftkräfte. Versuche mit unterschiedlich stark gefalteten Partikeloberflächen weisen auf geringere Haftkräfte hin, wenn sich die Partikel an Stellen geringerer Krümmungsradien berühren. Dispergierversuche in einer definierten Rohrströmung (Deagglomerator) lassen auf einen kaskadenartigen Agglomeratzerfall schließen. Durch Sprüheinbettung unterschiedlicher Modellwirkstoffe (Salbutamolsulfat, Ipratropiumbromid, Budesonid) in Hydroxypropyl-β-Cyclodextrin konnten sowohl Einzelformulierungen als auch eine Kombinationsformulierung mit allen drei Wirkstoffen erzeugt werden. Diese weisen bei einem Wirkstoffgehalt bis max. 14% selbst nach vierwöchiger Offenlagerung bei 40°C und 75% r.F. keine bzw. nur geringfügige Veränderungen in der „Fine Particle Dose“ (FPD) auf. Die „Fine Particle Fraction“ (FPF) liegt bei diesen Formulierungen im Bereich von 40% bis 75%. In Verbindung mit einem geeigneten Pack- bzw. Trockenmittel, ist hierbei mit einer physikalischen Stabilität zu rechnen, die eine sinnvolle Produktlaufzeit eines Inhalationspulvers ermöglicht. Formulierungen mit höheren Wirkstoffkonzentrationen zeigen dagegen stärkere Veränderungen nach Stresslagerung. Als Beispiel einer kristallinen Sprühtrocknungsformulierung konnte ein Pulver bestehend aus Mannitol und Budesonid erzeugt werden.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

This thesis investigates two distinct research topics. The main topic (Part I) is the computational modelling of cardiomyocytes derived from human stem cells, both embryonic (hESC-CM) and induced-pluripotent (hiPSC-CM). The aim of this research line lies in developing models of the electrophysiology of hESC-CM and hiPSC-CM in order to integrate the available experimental data and getting in-silico models to be used for studying/making new hypotheses/planning experiments on aspects not fully understood yet, such as the maturation process, the functionality of the Ca2+ hangling or why the hESC-CM/hiPSC-CM action potentials (APs) show some differences with respect to APs from adult cardiomyocytes. Chapter I.1 introduces the main concepts about hESC-CMs/hiPSC-CMs, the cardiac AP, and computational modelling. Chapter I.2 presents the hESC-CM AP model, able to simulate the maturation process through two developmental stages, Early and Late, based on experimental and literature data. Chapter I.3 describes the hiPSC-CM AP model, able to simulate the ventricular-like and atrial-like phenotypes. This model was used to assess which currents are responsible for the differences between the ventricular-like AP and the adult ventricular AP. The secondary topic (Part II) consists in the study of texture descriptors for biological image processing. Chapter II.1 provides an overview on important texture descriptors such as Local Binary Pattern or Local Phase Quantization. Moreover the non-binary coding and the multi-threshold approach are here introduced. Chapter II.2 shows that the non-binary coding and the multi-threshold approach improve the classification performance of cellular/sub-cellular part images, taken from six datasets. Chapter II.3 describes the case study of the classification of indirect immunofluorescence images of HEp2 cells, used for the antinuclear antibody clinical test. Finally the general conclusions are reported.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Im Mittelpunkt dieser Arbeit stand das große L-Hüllprotein (L) des Hepatitis B - Virus. L bildet eine ungewöhnliche duale Topologie in der ER-Membran aus, welche auch im reifen Viruspartikel erhalten bleibt. In einem partiellen, posttranslationalen Reifungsprozess wird die sogenannte PräS-Region von der zytosolischen Seite der Membran aus in das ER-Lumen transloziert. Aufgrund seiner dualen Topologie und der damit verbundenen Multifunktionalität übernimmt L eine Schlüsselfunktion im viralen Lebenszyklus. Ein Schwerpunkt dieser Arbeit lag deshalb darin, neue zelluläre Interaktionspartner des L-Hüllproteins zu identifizieren. Ihre Analyse sollte helfen, das Zusammenspiel des Virus mit der Wirtszelle besser zu verstehen. Hierfür wurde das Split - Ubiquitin Hefe - Zwei - Hybrid System eingesetzt, das die Interaktionsanalyse von Membranproteinen und Membran-assoziierten Proteinen ermöglicht. Zwei der neu identifizierten Interaktionspartner, der v-SNARE Bet1 und Sec24A, die Cargo-bindende Untereinheit des CoPII-vermittelten vesikulären Transports, wurden weitergehend im humanen Zellkultursystem untersucht. Sowohl für Bet1 als auch für Sec24A konnte die Interaktion mit dem L-Hüllprotein bestätigt und der Bindungsbereich eingegrenzt werden. Die Depletion des endogenen Bet1 reduzierte die Freisetzung L-haltiger, nicht aber S-haltiger subviraler Partikel (SVP) deutlich. Im Gegensatz zu Bet1 interagierte Sec24A auch mit dem mittleren M- und kleinen S-Hüllprotein von HBV. Die Inhibition des CoPII-vermittelten vesikulären Transportweges durch kombinierte Depletion der vier Sec24 Isoformen blockierte die Freisetzung sowohl L- als auch S-haltiger SVP. Dies bedeutet, dass die HBV - Hüllproteine das ER CoPII-vermittelt verlassen, wobei sie aktiv Kontakt zur Cargo-bindenden Untereinheit Sec24A aufnehmen. Der effiziente Export der Hüllproteine aus dem ER ist für die Virusmorphogenese und somit für den HBV - Lebenszyklus essentiell. rnEin weiterer Schwerpunkt dieser Arbeit basierte auf der Interaktion des L-Hüllproteins mit dem ER-luminalen Chaperon BiP. In der vorliegenden Arbeit wurde überprüft, ob BiP, ähnlich wie das zytosolische Chaperon Hsc70, an der Ausbildung der dualen Topologie des L-Hüllproteins beteiligt ist. Hierfür wurde BiP durch die ektopische Expression seiner Ko-Chaperone BAP und ERdj4 in seiner Substrat-bindenen Kapazität manipuliert. ERdj4, ein Mitglied der Hsp40 - Proteinfamilie, stimuliert die ATPase-Aktivität von BiP, was die Substratbindung stabilisiert. Der Nukleotid - Austauschfaktor BAP hingegen vermittelt die Auflösung des BiP - Substrat - Komplexes. Die Auswirkung der veränderten in vivo-Aktivität von BiP auf die posttranslationale PräS-Translokation wurde mit Proteaseschutz - Versuchen untersucht. Die ektopische Expression des positiven als auch des negativen Regulators von BiP resultierte in einer drastischen Reduktion der posttranslationalen PräS-Translokation. Ein vergleichbarer Effekt wurde nach Manipulation des BiP ATPase - Zyklus durch Depletion der zellulären ATP - Konzentration beobachtet. Dies spricht dafür, dass das ER-luminale Chaperon BiP, zusammen mit Hsc70, eine zentrale Rolle in der Ausbildung der dualen Topologie des L-Hüllproteins spielt. rnZwei weitere Proteine, Sec62 und Sec63, die sich für die posttranslationale Translokation in der Hefe als essentiell erwiesen haben, wurden in die Analyse der dualen Topologie des L-Hüllproteins einbezogen. Interessanterweise konnte eine rein luminale Ausrichtung der PräS-Region nach kombinierter Depletion des endogenen Sec62 und Sec63 beobachtet werden. Dies deutet an, dass sowohl Sec62 als auch Sec63 an der Ausbildung der dualen Topologie des L-Hüllproteins beteiligt sind. In Analogie zur Posttranslokation der Hefe könnte Sec62 als Translokon-assoziierter Rezeptor für Substrate der Posttranslokation, und damit der PräS-Region, dienen. Sec63 könnte mit seiner J-Domäne BiP zum Translokon rekrutieren und daraufhin dessen Substrat-bindende Aktivität stimulieren. BiP würde dann, einer molekularen Ratsche gleich, die PräS-Region durch wiederholtes Binden und Freisetzen aktiv in das ER-Lumen hereinziehen, bis eine stabile duale Topologie des L-Hüllproteins ausgebildet ist. Die Bedeutung von Sec62 und Sec63 für den HBV - Lebenszyklus wird dadurch untermauert, dass sowohl die ektopische Expression als auch die Depletion des endogenen Sec63 die Freisetzung L-haltiger SVP deutlich reduziert. rn

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Primary biogenic aerosol (PBA) particles account for large proportions of air particulate matter, and they can influence the hydrological cycle and climate as nuclei for water droplets and ice crystals in clouds, fog, and precipitation. Moreover, they can cause or enhance human, animal, and plant diseases. The actual abundance and properties of PBA particles and components in the atmosphere are, however, still poorly understood and quantified. rnIn this study, the identity, diversity, and frequency of occurrence of PBA particles were investigated by DNA analysis. Methods for the extraction, amplification, and analysis of DNA from aerosol filter samples were developed and optimized for different types of organisms, including fungi, bacteria, and plants. The investigations were focused on fungal DNA, and over 2500 sequences were obtained from air samples collected at different locations and climatic zones around the world (tropical, mid-latitude, sub-polar; continental, marine). rnNearly all fungal DNA sequences could be attributed to the phyla of Ascomycota and Basidiomycota. With regard to species richness, the ratio of Basidiomycota to Ascomycota was much higher in continental air samples (~60:40) than in marine air samples (~30:70). Pronounced differences in the relative abundance and seasonal cycles of various groups of fungi were detected in coarse and fine particulate matter from continental air, with more plant pathogens in the coarse and more human pathogens and allergens in the respirable fine particle fraction (<3 µm). The results of this study provide new information and insights into the sources of PBA particles and the interactions of the biosphere with the atmosphere, climate, and public health. rn

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The Eph receptor tyrosine kinases mediate juxtacrine signals by interacting “in trans” with ligands anchored to the surface of neighboring cells via a GPI-anchor (ephrin-As) or a transmembrane segment (ephrin-Bs), which leads to receptor clustering and increased kinase activity. Additionally, soluble forms of the ephrin-A ligands released from the cell surface by matrix metalloproteases can also activate EphA receptor signaling. Besides these trans interactions, recent studies have revealed that Eph receptors and ephrins coexpressed in neurons can also engage in lateral “cis” associations that attenuate receptor activation by ephrins in trans with critical functional consequences. Despite the importance of the Eph/ephrin system in tumorigenesis, Eph receptor-ephrin cis interactions have not been previously investigated in cancer cells. Here we show that in cancer cells, coexpressed ephrin-A3 can inhibit the ability of EphA2 and EphA3 to bind ephrins in trans and become activated, while ephrin-B2 can inhibit not only EphB4 but also EphA3. The cis-inhibition of EphA3 by ephrin-B2 implies that in some cases ephrins that cannot activate a particular Eph receptor in trans can nevertheless inhibit its signaling ability through cis association. We also found that an EphA3 mutation identified in lung cancer enhances cis interaction with ephrin-A3. These results suggest a novel mechanism that may contribute to cancer pathogenesis by attenuating the tumor suppressing effects of Eph receptor signaling pathways activated by ephrins in trans (Falivelli et al. 2013).

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Die Funktionalisierung anorganischer Nanopartikel stellt einen Schlüsselschritt in der Herstellung von Nanokompositen dar. Nanokomposite erzielen ein wachsendes Interesse im Bereich der Polymer- und der Materialwissenschaften, da die Kombination mehrerer Materialien mit unterschiedlichen Eigenschaften, wie etwa die Kombination anorganischer Nanopartikel mit Polymeren, große Synergieeffekte erhoffen lässt.rnrnDer Einbau anorganischer Nanopartikel in polymere Matrixmaterialien zur Verbesserung oder Einführung mechanischer, optischer oder magnetischer Eigenschaften von Polymeren bedarf allerdings der Modifizierung der Oberfläche des anorganischen Materials, um die für die positiven Synergieeffekte essentielle Kompatibilität zwischen Füllstoff und Matrix zu erreichen.rnrnEine Vielzahl anorganischer Partikel ist bereits als wässrige Dispersion erhältlich (SiO2, Al2O3, CeO2, ZrO2, ...). Mehrkomponenten- Lösungsmittelsysteme ermöglichen den Transfer dieser Partikel in eine unpolare Umgebung und gleichzeitig deren Funktionalisierung mit amphiphilen Copolymeren. Aufgrund der reversiblen Schaltbarkeit dieser Lösungsmittelsysteme zwischen einem einphasigen und zweiphasigen Zustand werden die zu Beginn in zwei nichtmischbaren Phasen vorliegenden Reaktionspartner durch Übergang in einen einphasigen Zustand unter homogenen Bedingungen in Kontakt gebracht und durch eine erneute Phasentrennung isoliert.rnEin weiterer Vorteil dieser Lösungsmittelsysteme ist deren Tolerierung funktioneller Gruppen in den verwendeten amphiphilen Copolymeren, welche nicht in Wechselwirkung mit der Partikeloberfläche stehen. Beispielsweise können Amine in den amphiphilen Copolymeren für die Wechselwirkung der funktionalisierten Partikel mit einer Polyurethanmatrix dienen, Alkine können mittels einer 1,3-dipolaren Cycloaddition umgesetzt werden oder aber perfluorierten Seitenketten in den Seitenketten der amphiphilen Copolymere die Kompatibilisierung der funktionalisierten Partikel mit einem perfluorierten Polymer gewährleisten.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Within this work, a particle-polymer surface system is studied with respect to the particle-surface interactions. The latter are governed by micromechanics and are an important aspect for a wide range of industrial applications. Here, a new methodology is developed for understanding the adhesion process and measure the relevant forces, based on the quartz crystal microbalance, QCM. rnThe potential of the QCM technique for studying particle-surface interactions and reflect the adhesion process is evaluated by carrying out experiments with a custom-made setup, consisting of the QCM with a 160 nm thick film of polystyrene (PS) spin-coated onto the quartz and of glass particles, of different diameters (5-20µm), deposited onto the polymer surface. Shifts in the QCM resonance frequency are monitored as a function of the oscillation amplitude. The induced frequency shifts of the 3rd overtone are found to decrease or increase, depending on the particle-surface coupling type and the applied oscillation (frequency and amplitude). For strong coupling the 3rd harmonic decreased, corresponding to an “added mass” on the quartz surface. However, positive frequency shifts are observed in some cases and are attributed to weak-coupling between particle and surface. Higher overtones, i.e. the 5th and 7th, were utilized in order to derive additional information about the interactions taking place. For small particles, the shift for specific overtones can increase after annealing, while for large particle diameters annealing causes a negative frequency shift. The lower overtones correspond to a generally strong-coupling regime with mainly negative frequency shifts observed, while the 7th appears to be sensitive to the contact break-down and the recorded shifts are positive.rnDuring oscillation, the motion of the particles and the induced frequency shift of the QCM are governed by a balance between inertial forces and contact forces. The adherence of the particles can be increased by annealing the PS film at 150°C, which led to the formation of a PS meniscus. For the interpretation, the Hertz, Johnson-Kendall-Roberts, Derjaguin-Müller-Toporov and the Mindlin theory of partial slip are considered. The Mindlin approach is utilized to describe partial slip. When partial slip takes place induced by an oscillating load, a part of the contact ruptures. This results in a decrease of the effective contact stiffness. Additionally, there are long-term memory effects due to the consolidation which along with the QCM vibrations induce a coupling increase. However, the latter can also break the contact, lead to detachment and even surface damage and deformation due to inertia. For strong coupling the particles appear to move with the vibrations and simply act as added effective mass leading to a decrease of the resonance frequency, in agreement with the Sauerbrey equation that is commonly used to calculate the added mass on a QCM). When the system enters the weak-coupling regime the particles are not able to follow the fast movement of the QCM surface. Hence, they effectively act as adding a “spring” with an additional coupling constant and increase the resonance frequency. The frequency shift, however, is not a unique function of the coupling constant. Furthermore, the critical oscillation amplitude is determined, above which particle detach. No movement is detected at much lower amplitudes, while for intermediate values, lateral particle displacement is observed. rnIn order to validate the QCM results and study the particle effects on the surface, atomic force microscopy, AFM, is additionally utilized, to image surfaces and measure surface forces. By studying the surface of the polymer film after excitation and particle removal, AFM imaging helped in detecting three different meniscus types for the contact area: the “full contact”, the “asymmetrical” and a third one including a “homocentric smaller meniscus”. The different meniscus forms result in varying bond intensity between particles and polymer film, which could explain the deviation between number of particles per surface area measured by imaging and the values provided by the QCM - frequency shift analysis. The asymmetric and the homocentric contact types are suggested to be responsible for the positive frequency shifts observed for all three measured overtones, i.e. for the weak-coupling regime, while the “full contact” type resulted in a negative frequency shift, by effectively contributing to the mass increase of the quartz..rnThe interplay between inertia and contact forces for the particle-surface system leads to strong- or weak-coupling, with the particle affecting in three mentioned ways the polymer surface. This is manifested in the frequency shifts of the QCM system harmonics which are used to differentiate between the two interaction types and reflect the overall state of adhesion for particles of different size.rn

Relevância:

30.00% 30.00%

Publicador:

Resumo:

La presenza di micotossine nelle materie prime desta grande preoccupazione a causa delle importanti implicazioni nella sicurezza di alimenti e mangimi. Lo scopo di questo lavoro è stato quello di mettere a punto e validare una metodica analitica rapida e semplice, in cromatografia liquida ad ultra prestazione accoppiata a spettrometria di massa-tandem (UPLC-MS/MS), per la determinazione simultanea di differenti micotossine: aflatossine (B1, B2, G1, G2), ocratossina A, fumonisine (B1, B2), deossinivalenolo e zearalenone in matrici biologiche. Il metodo sviluppato per l’analisi di campioni di mangime secco per cani ha mostrato prestazioni adeguate ed è stato applicato a 49 campioni reperibili in commercio, al fine di valutare la sua efficacia e di ottenere alcuni dati preliminari sulla contaminazione da micotossine in alimenti per cani disponibili sul mercato italiano. Lo studio ha evidenziato una percentuale alta di campioni positivi, contenenti principalmente fumonisine, deossinivalenolo e ocratossina A; tutti i tenori si sono dimostrati inferiori al limite di legge previsto (Racc. CE 576/2006). Una seconda metodica è stata messa a punto e validata per l’identificazione e la quantificazione micotossine in campioni di formaggio; per questa matrice è stata inserita anche l’aflatossina M1, specifica dei prodotti lattiero - caseari. Le differenti proprietà chimico-fisiche degli analiti e la complessità della matrice hanno implicato alcune difficoltà nello sviluppo della metodica. Tuttavia, il metodo validato si è mostrato rapido, semplice ed affidabile ed è stato applicato a diversi tipi di formaggi per verificarne la versatilità. I risultati preliminari hanno mostrato l’assenza di contaminazione da parte delle micotossine in oggetto. Entrambi i metodi si sono dimostrati utili per il monitoraggio di contaminanti in matrici complesse ad oggi ancora poco studiate.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Al fine di migliorare le tecniche di coltura cellulare in vitro, sistemi a bioreattore sono sempre maggiormente utilizzati, e.g. ingegnerizzazione del tessuto osseo. Spinner Flasks, bioreattori rotanti e sistemi a perfusione di flusso sono oggi utilizzati e ogni sistema ha vantaggi e svantaggi. Questo lavoro descrive lo sviluppo di un semplice bioreattore a perfusione ed i risultati della metodologia di valutazione impiegata, basata su analisi μCT a raggi-X e tecniche di modellizzazione 3D. Un semplice bioreattore con generatore di flusso ad elica è stato progettato e costruito con l'obiettivo di migliorare la differenziazione di cellule staminali mesenchimali, provenienti da embrioni umani (HES-MP); le cellule sono state seminate su scaffold porosi di titanio che garantiscono una migliore adesione della matrice mineralizzata. Attraverso un microcontrollore e un'interfaccia grafica, il bioreattore genera tre tipi di flusso: in avanti (senso orario), indietro (senso antiorario) e una modalità a impulsi (avanti e indietro). Un semplice modello è stato realizzato per stimare la pressione generata dal flusso negli scaffolds (3•10-2 Pa). Sono stati comparati tre scaffolds in coltura statica e tre all’interno del bioreattore. Questi sono stati incubati per 21 giorni, fissati in paraformaldehyde (4% w/v) e sono stati soggetti ad acquisizione attraverso μCT a raggi-X. Le immagini ottenute sono state poi elaborate mediante un software di imaging 3D; è stato effettuato un sezionamento “virtuale” degli scaffolds, al fine di ottenere la distribuzione del gradiente dei valori di grigio di campioni estratti dalla superficie e dall’interno di essi. Tale distribuzione serve per distinguere le varie componenti presenti nelle immagini; in questo caso gli scaffolds dall’ipotetica matrice cellulare. I risultati mostrano che sia sulla superficie che internamente agli scaffolds, mantenuti nel bioreattore, è presente una maggiore densità dei gradienti dei valori di grigio ciò suggerisce un migliore deposito della matrice mineralizzata. Gli insegnamenti provenienti dalla realizzazione di questo bioreattore saranno utilizzati per progettare una nuova versione che renderà possibile l’analisi di più di 20 scaffolds contemporaneamente, permettendo un’ulteriore analisi della qualità della differenziazione usando metodologie molecolari ed istochimiche.