On the performance of a dual-mode non-linear vibration energy harvesting device

The research trend for harvesting energy from the ambient vibration sources has moved from using a linear resonant generator to a non-linear generator in order to improve on the performance of a linear generator; for example, the relatively small bandwidth, intolerance to mistune and the suitability of the device for low-frequency applications. This article presents experimental results to illustrate the dynamic behaviour of a dual-mode non-linear energy-harvesting device operating in hardening and bi-stable modes under harmonic excitation. The device is able to change from one mode to another by altering the negative magnetic stiffness by adjusting the separation gap between the magnets and the iron core. Results for the device operating in both modes are presented. They show that there is a larger bandwidth for the device operating in the hardening mode compared to the equivalent linear device. However, the maximum power transfer theory is less applicable for the hardening mode due to occurrence of the maximum power at different frequencies, which depends on the non-linearity and the damping in the system. The results for the bi-stable mode show that the device is insensitive to a range of excitation frequencies depending upon the input level, damping and non-linearity.

Correlação linear e espacial entre a produtividade do feijoeiro e atributos físicos de um LATOSSOLO VERMELHO Distroférrico de Selvíria, Estado de Mato Grosso do Sul

Os atributos físicos do solo têm se mostrado de grade interesse para a agricultura contemporânea, uma vez que refletem decisivamente sobre a produtividade vegetal. em 2006, no campus da Faculdade de Engenharia de Ilha Solteira, Unesp, analisouse a produtividade do feijoeiro (PG) no sistema plantio direto irrigado, a resistência mecânica do solo à penetração (RP), a densidade do solo (DS) e as umidades gravimétrica (UG) e volumétrica (UV) em profundidade, num LATOSSOLO VERMELHO Distroférrico. O objetivo foi determinar as correlações lineares e espaciais, entre os atributos estudados, visando selecionar um indicador da qualidade física do solo de boa representatividade para a PG. Foi instalada a malha, para a coleta de dados contendo 135 pontos amostrais, numa área de 7.500 m². A correlação linear entre a produtividade de grãos com os atributos do solo foi baixa. As de melhor correlação com a PG foram a DS1 e RP1. Contudo, do ponto de vista espacial, houve significativa correlação inversa entre a PG e DS1. Portanto, no presente trabalho, dentre os atributos estudados, a DS, avaliada na camada de 0-0,10 m, apresentou-se como o melhor indicador da qualidade física de um Latossolo de Selvíria, quando destinado à produtividade de grãos de feijão.

Correlação linear e espsacial entre a produtividade de feijão e a porosidade de um Latossolo Vermelho de Selvíria (MS)

Soil porosity influences plant development since root growth and crop yield are determined by the root depth. The objective of this study was to investigate the linear and spatial variability and correlations between common bean yield and soil porosity. The bean grain yield of the irrigated cultivar Carioca IAC was analyzed in the growing season 2004/2005, in Selviria-MS, as well as macroporosity (MA), microporosity (MI) and total porosity (TP), in a Dystroferric Red Latosol, at four depths: 1 (0.0-0.10 m), 2 (0.10-0.20 M), 3 (0.20-0.30 m) and 4 (0.30-0.40 m). Soil and plant data were collected in a geostatistical grid with 135 points spaced 10 m apart, covering an area of 50 x 150 m. The data of the studied attributes did not vary randomly and the values were intermediate to low. They followed well-defined spatial standards, reaching between 11.70-104.40 m. on the other hand, the linear correlation between the plant and soil attributes was low, due to the high number of observations. Grain yield had the best linear correlations with MA1b, MI1 and TP3. From the spatial point of view, the inverse correlation between PG and #TP2 was outstanding. At the sites where #TP2 diminished (0.030-0.045 m(3) m(-3)) the yield varied from 2,173 to 3,529 kg ha(-1) and where it increased (0.045-0.076 m(3) m(-3)), the yield was between 1,630 and 2,173 kg ha(-1). Therefore, the total soil porosity, evaluated in the 0.10-0.20 m layer (#TP2), indicated the importance of the contact root/soil and was in turn a satisfactory indicator of soil physical quality, with a view to the grain yield of irrigated common bean.

Correlação linear e espacial dos componentes de produção e produtividade da soja

The soybean is the crop most cultivated in Brazil, with great socioeconomic importance. In the agriculture year 2008/09 in Selviria County, Mato Grosso do Sul State, in the Brazilian Savannah, was analyzed the production components and the soybean yield cultivated in a Typic Acrustox on no-tillage. The main purpose objective was select among the production components number of pods per plant, number of grains per pod, number of grains per plant, mass of a thousand grains, mass of grains per plant and population of plants, which of the best linear and spatial correlation aiming explain the soybean yield variability. The irregular geostatistical grid was installed to collect of data, with 120 sampling points, in an area of 8.34 ha. The values of spatial dependence range to be utilized should be among 38.1 and 114.7 meters. The model of the adjusted semivariograma was predominantly the spherical. of the lineal and spatial point of view, the number of pods per plant and the mass of grains per plant they were correlated in a direct way with the soybean yield, demonstrating be the best components to esteem her.

Correlação linear entre componentes da produção e produtividade do arroz de terras altas em sistema plantio direto

The rice is one of the main sources of the humanity's feeding. During the agricultural year 2009/2010, in Selviria County, Mato Grosso do Sul State, in the Brazilian Savannah, an experiment was installed with rice upland in a Dystropherric Red Latosol (Typic Acrustox) under no-tillage, irrigated by central pivot, with the purpose of selecting the best components production to explain the variability the irrigated rice yield upland. The geostatistical grid was installed, to collect the data, with 120 sampling points, in an area of 3.0 ha and and homogeneous slope of 0.055 m m(-1). The medium rice yield was of the 5980 kg ha(-1). For the simple lineal regressions, the number of spikelets grenades for panicle presented the best direct potential correlation with the yield rice, given for: PGO = 115,5.NEG(0,770). However, for the multiple lineal regressions, the equation equacao PGO = 2754,30-411,55.NEG-461,07. NEC+436,59. NET it was the one that better she came to esteem the yield rice. However, spatial, it was not possible to establish correlation between the yield rice and the components production, once none of those it presented spatial dependence in their data.

Bifurcation of limit cycles from an n-dimensional linear center inside a class of piecewise linear differential systems

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

On an Optimal Linear Control of a Chaotic Non-Ideal Duffing System

In this work, we use a nonlinear control based on Optimal Linear Control. We used as mathematical model a Duffing equation to model a supporting structure for an unbalanced rotating machine with limited power (non-ideal motor). Numerical simulations are performed for a set control parameter (depending on the voltage of the motor, that is, in the static and dynamic characteristic of the motor) The interaction of the non-ideal excitation with the structure may lead to the occurrence of interesting phenomena during the forward passage through the several resonance states of the system. Chaotic behavior is obtained for values of the parameters. Then, the proposed control strategy is applied in order to regulate the chaotic behavior, in order to obtain a periodic orbit and to decrease its amplitude. Both methodologies were used in complete agreement between them. The purpose of the paper is to give suggestions and recommendations to designers and engineers on how to drive this kind of system through resonance.

Identificação e comparação entre controle preditivo com modelo não linear e PI sintonizados com PSO em sistema de separação gravitacional de águia-óleo

The separation methods are reduced applications as a result of the operational costs, the low output and the long time to separate the uids. But, these treatment methods are important because of the need for extraction of unwanted contaminants in the oil production. The water and the concentration of oil in water should be minimal (around 40 to 20 ppm) in order to take it to the sea. Because of the need of primary treatment, the objective of this project is to study and implement algorithms for identification of polynomial NARX (Nonlinear Auto-Regressive with Exogenous Input) models in closed loop, implement a structural identification, and compare strategies using PI control and updated on-line NARX predictive models on a combination of three-phase separator in series with three hydro cyclones batteries. The main goal of this project is to: obtain an optimized process of phase separation that will regulate the system, even in the presence of oil gushes; Show that it is possible to get optimized tunings for controllers analyzing the mesh as a whole, and evaluate and compare the strategies of PI and predictive control applied to the process. To accomplish these goals a simulator was used to represent the three phase separator and hydro cyclones. Algorithms were developed for system identification (NARX) using RLS(Recursive Least Square), along with methods for structure models detection. Predictive Control Algorithms were also implemented with NARX model updated on-line, and optimization algorithms using PSO (Particle Swarm Optimization). This project ends with a comparison of results obtained from the use of PI and predictive controllers (both with optimal state through the algorithm of cloud particles) in the simulated system. Thus, concluding that the performed optimizations make the system less sensitive to external perturbations and when optimized, the two controllers show similar results with the assessment of predictive control somewhat less sensitive to disturbances

Implantes de resina de poliuretana vegetal (Ricinus communis) na tração linear, fixação e fusão vertebral no cão: estudo experimental

Placa e espaçador de polímero derivado do óleo de mamona (PDOM) (Ricinus communis) foram avaliados clínica, radiográfica e histologicamente na tração linear, fixação e fusão vertebral cervical em 20 cães adultos, sem raça definida, pesando entre 17 e 22kg. Foram sacrificados quatro animais aos 10, 30, 60, 90 e 120 dias de pós-operatório. Após exposição da coluna cervical, por acesso ventral, o disco intervertebral de C4-C5 foi fenestrado e a abordagem ao canal medular foi feita por meio de fenda óssea. Um espaçador de PDOM foi colocado preenchendo o defeito ósseo. Os corpos vertebrais C4-C5 foram fixados com placa do mesmo material, utilizando-se dois parafusos corticais em cada corpo vertebral. Apenas um animal apresentou déficit neurológico no pós-operatório imediato. Radiograficamente as vértebras mostravam-se normais e alinhadas, sem colapso do espaço intervertebral, porém não houve neoformação óssea entre as vértebras. Ao exame mielográfico, não houve compressão da medula espinhal. Os implantes foram efetivos em manter a tração linear e fixação das vértebras cervicais e não ocorreu a fusão vertebral.

Influence of Different Base Thicknesses on Maxillary Complete Denture Processing: Linear and Angular Graphic Analysis on the Movement of Artificial Teeth

Objective: The purpose of this study was to compare the dental movement that occurs during the processing of maxillary complete dentures with 3 different base thicknesses, using 2 investment methods, and microwave polymerization.Methods: A sample of 42 denture models was randomly divided into 6 groups (n = 7), with base thicknesses of 1.25, 2.50, and 3.75 mm and gypsum or silicone flask investment. Points were demarcated on the distal surface of the second molars and on the back of the gypsum cast at the alveolar ridge level to allow linear and angular measurement using AutoCAD software. The data were subjected to analysis of variance with double factor, Tukey test and Fisher (post hoc).Results: Angular analysis of the varying methods and their interactions generated a statistical difference (P = 0.023) when the magnitudes of molar inclination were compared. Tooth movement was greater for thin-based prostheses, 1.25 mm (-0.234), versus thick 3.75 mm (0.2395), with antagonistic behavior. Prosthesis investment with silicone (0.053) showed greater vertical change compared with the gypsum investment (0.032). There was a difference between the point of analysis, demonstrating that the changes were not symmetric.Conclusions: All groups evaluated showed change in the position of artificial teeth after processing. The complete denture with a thin base (1.25 mm) and silicone investment showed the worst results, whereas intermediate thickness (2.50 mm) was demonstrated to be ideal for the denture base.

Linear dimensional changes of denture base and hard chair-side reline resins after disinfection

Objectives: This study evaluated the effect of disinfection by immersion in sodium perborate (50 degrees C/10 min) or microwave irradiation (650 W/6 min) on the linear dimensional change (LDC) of four reline resins (Kooliner-K, New Truliner-N, Tokuso Rebase Fast-T, Ufi Gel Hard-U) and one heat-polymerizing denture base resin (Lucitone 550-L). Methods: Specimens (50.0 mm diameter, 0.5 mm thickness) were made using a split mold with reference points, and divided into two controls and four test groups (u = 8). The distances between the points were measured on the mold (baseline readings), and compared to those obtained from the specimens after: polymerization or immersion in water (37 degrees C) for 7 days (controls); 2 or 7 cycles of disinfection by immersion or microwave irradiation. Results: the two-way ANOVA and Tukey's test (alpha = 0.05) showed that microwave disinfection significantly increased the mean LDC of materials L (-1.43%), N (-1.27%) and K (-1.06%). Material N also exhibited a significant increase in LDC after two cycles of chemical disinfection (-0.73%). For U (-0.47%) and T (-0.21%) materials, no significant changes in LDC were found. Conclusions: Microwave disinfection increases the shrinkage of materials L, N, and K. The dimensional stability of resins U and T was not affected by the disinfection methods evaluated. (c) 2006 Wiley Periodicals, Inc.

Effect of Incorporation of Disinfectant Solutions on Setting Time, Linear Dimensional Stability, and Detail Reproduction in Dental Stone Casts

Purpose: The aim of this paper was to analyze the influence of incorporation of disinfectants during the cast die stone-setting time. Setting time, linear dimensional stability, and reproduction details on casts were measured.Materials and Methods: Die stone type IV specimens with disinfection solutions (sodium hypochlorite 1%, glutaraldehyde 2%, chlorhexidine 2%) were incorporated in two concentrations (50%, 100%). The detail reproduction, dimensional stability, and setting time were tested in accordance with ADA recommendations.Results: Disinfecting solutions promoted an increase in setting time compared to control; sodium hypochlorite was responsible for the highest setting time. The addition of undiluted sodium hypochlorite 1.0% led to contraction during setting, but the groups with 50% diluted sodium hypochlorite 1.0% and undiluted chlorhexidine 2.0% resulted in intermediate values compared to the other groups, thus matching the control. The others did not demonstrate any effect on expansion. For detail reproduction, it was observed that the control group presented results similar to the others, except those where sodium hypochlorite was added.Conclusions The addition of sodium hypochlorite in both dilutions significantly altered, negatively, all the evaluated properties. But the addition of glutaraldehyde and chlorhexidine did not promote any significant alterations in the evaluated properties.

Influence of Microwave Disinfection on the Linear Dimensional Stability of Complete Dentures: A Clinical Study

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of the optimal quantity of crop residues for energy in sugarcane crop management using linear programming in variety selection and planting strategy

The aim of this work was to present organizational models for optimizing the reduction of crop residue generated by the sugarcane culture. The first model consisted of the selection of varieties of sugarcane to be planted meeting the mill requirements and, at the same time, to minimize the quantity of residue produced. The second model discussed the use of residue to produce energy. This is related to the selection of variety and quantity to be planted, in order to meet the requirements of the mill, to reduce the quantity of residue, and to maximize as much as possible the energy production. The use of linear programming was proposed. The two models presented similar results in this study, and both may be used to define the varieties and areas to be cultivated. (C) 2001 Published by Elsevier B.V. Ltd.

Heterogeneity correction in the construction of optimized planning in radiotherapy using linear programming

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)