Avaliação da silagem de grãos de milho úmido com diferentes volumosos para tourinhos em terminação: desempenho e características de carcaça

O experimento foi realizado com o objetivo de comparar os efeitos do fornecimento de silagem de grãos de milho úmido com o milho em grão seco, associados à silagem de milho ou ao bagaço in natura de cana-de-açúcar, sobre o desempenho e as características da carcaça de bovinos em terminação. em blocos ao acaso e esquema fatorial 2 × 2, 28 tourinhos Santa Gertrudes (dez meses de idade e peso corporal inicial de 245 kg) foram mantidos em confinamento durante 142 dias. Os animais foram mantidos em baias individuais e receberam dietas com 12 e 20% da MS em forma de bagaço ou silagem, respectivamente. O milho úmido foi moído e ensilado quando se encontrava com 30% de umidade. Não houve interação significativa tipo de volumoso x tipo de processamento do milho sobre as variáveis estudadas. O bagaço mostrou-se viável como fonte exclusiva de fibra, apesar de os resultados de ganho de peso, eficiência alimentar, peso e rendimento de carcaça e espessura de gordura subcutânea terem sido inferiores aos obtidos com a silagem de milho. O ganho diário de peso nos animais alimentados com o bagaço foi em torno de 1,3 kg, enquanto, com a silagem, foi de 1,5 kg. O consumo de MS não foi influenciado pelo tipo de volumoso ou pelo processamento do milho. O uso da silagem de grãos de milho úmido melhorou a eficiência alimentar em 9,7% e reduziu o peso do fígado quando comparado ao milho seco, mas não alterou as demais características avaliadas.

Agentes polinizadores e produção de grãos em cultura de café arábica cv. “Catuaí Vermelho”

Coffee (Coffea arabica L.) plants had the pollination process of their flowers studied in three coffee producing regions in Brazil: the first in Ribeirao Preto, state of São Paulo, in September of 2004, the second in Carmo do Paraiba, in the state of Minas Gerais, in October of 2006, and, the third, in Altinopolis, state of São Paulo, in September of 2007. In all these locations the coffee variety used was the 'Catuai Vermelho'. The pollinator species visiting the flowers, the frequency with which the flowers were visited by the insects, and the type of material collected by them ( nectar and/or pollen) were determined by counts taking place at the first 10 minutes of each hour from 7:00 AM till 6:00 PM during the months mentioned above. To estimate the fructification percentage, 25 branches were identified with color threads and protected with wire frames covered with a nylon fabric to prevent them from being visited by insects. Another group of 25 branches was similarly identified but remained without any covering so that their flowers were thus freely visited by insects. on the average, the most frequent pollinator was the Africanized bee Apis mellifera (73.7%) followed by the bee Trigona spinipes (14.5%), and Tetragonisca angustula (9.5%). The Africanized bee collected nectar and pollen to almost the same extent: 58.5% of the first and 41.5% of the second. To collect nectar, that species increased its visiting frequency up to 1:00 PM. To collect pollen, A. mellifera visited the flowers up to 1:00 PM with frequency peaks between 8:00 and 9:00 AM. T. spinipes collected pollen (58,5%) and nectar (41.5%). T. angustula collected only pollen. The branches freely visited by insects produced 181 grains on the average whereas those covered with the nylon fabric produced only 81 grains, this meaning a reduction of 55.25% in grain production. Coffee grains produced on the freely visited branches had a mean weight (1.13 g) significantly superior to that of those produced on the covered branches (0.94 g).

Produção de massa seca e nutrição de cultivares de arroz de terras altas sob condição de déficit hídrico e adubação silicatada

Although silicon has not been considered an essential element for plant growth and development, it has provided several benefits for the rice crop, especially under biotic and abiotic stress. The objective of this work was to evaluate macronutrient and silicon levels in upland rice cultivars cropped under water deficit and silicon fertilization. The experiment was carried out in greenhouse and the design was the completely randomized block, analyzed as a 2 x 2 x 2 factorial, which consisted of two cultivars, 'Maravilha' (modern group) and 'Caiapo' (traditional group), two silicon rates (0 and 350 kg ha(-1)) and two soil water tensions (-0.025 MPa and -0.050 MPa). Plant dry matter of the 'Maravilha' cultivar was higher compared to the other material. Higher soil water tensions decreased plant dry matter and macronutrient levels. Upland rice cultivars respond distinctively to soil water tensions and silicon rates.

Comparação econômica da produção de grãos secos e silagem de grãos úmidos de milho cultivado em sistema de plantio direto

No presente trabalho que foi realizado na Fazenda Experimental Lageado, da Universidade Estadual Paulista em Botucatu, SP, objetivou-se avaliar os custos envolvidos na produção de silagem de grãos úmidos de milho, tendo como referência o processamento seco deste cereal, ambos cultivados em sistema de plantio direto. Para a avaliação foram determinados os custos envolvidos nas operações de máquinas agrícolas, insumos e na etapa de pós-colheita. Os resultados observados permitiram concluir que o custo por hectare para produção de silagem de grãos úmidos foi de R$1.398,06, sendo 8,8% menor do que os custos para produção de milho seco (R$ 1.533,78).

Densidades populacionais de milho em arranjos espaciais convencional e equidistante entre plantas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Seletividade do nicosulfuron em três estádios fenológicos de milho-pipoca

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento de grãos e produção de fitomassa do girassol em função de adubações boratadas

Sunflower crop is a good option to no-tillage system; however, it is sensible to low B availability, what is common in tropical soils. The objective of this study was to evaluate the crop development, grain yield and grain size as affected by B fertilizer doses applied in the sowing and by leaf application. The experiment was conducted in controlled conditions, with four Borax doses (0; 1; 2 e 3 kg B ha(-1)) in the sowing interacting with four Boric Acid doses (0; 0,5; 1 e 2 kg B ha(-1)) by leaf application. The plants were managed until grain physiological maturity, when stems, leaves and capitula were sampled, besides the counting and weighing of two grain classes separated by size. The B fertilizer applied in the sowing lines increased total dry matter phytomass and grain yield. However, when interacting with high doses of B by leaf application, these values decreased. Grain size was increased with leaf fertilization, when B was not applied in the soil or with only 1 kg B ha(-1) in the sowing line. on the other hand, when B was applied from 2 to 3 kg ha(-1) in the crop sowing, high doses of leaf fertilizer affected grain filling.

Fontes alternativas e doses de nitrogênio no milho safrinha em sucessão à soja

A produtividade do milho safrinha pode ser aumentada com a adubação nitrogenada em cobertura mesmo quando cultivado em sucessão à soja. No entanto, existem inconsistências dos resultados especialmente quanto às fontes e doses a serem empregadas nessa modalidade de cultivo. Com o objetivo de avaliar o efeito de fontes e doses de nitrogênio em cobertura no milho safrinha, cultivado após soja no sistema plantio direto, conduziu-se o experimento em um Latossolo Vermelho distrófico, em Chapadão do Céu (GO). O delineamento experimental foi o de blocos ao acaso, em esquema fatorial 4 x 4, com quatro repetições. Os tratamentos foram constituídos pela combinação de quatro fontes (uréia, sulfato de amônio, uréia extrusada com produtos amiláceos (Amiréia® 180S) e sulfonitrato de amônio com inibidor de nitrificação (Entec® 26)) e quatro doses de nitrogênio (0; 30; 60 e 120 kg ha-1). A interação fonte x dose não foi significativa para nenhuma das variáveis avaliadas. A aplicação de nitrogênio na forma de entec proporcionou maiores teores de nitrogênio na folha do milho safrinha que o sulfato de amônio e a amiréia. A produtividade de grãos do milho safrinha foi maior quando o nitrogênio em cobertura foi fornecido na forma de sulfato de amônio, em comparação com a amiréia. A aplicação de nitrogênio em cobertura aumentou os teores de nitrogênio e enxofre na folha, altura da planta, diâmetro do colmo, número de espigas por planta e grãos por espiga, massa de 1.000 grãos e produtividade de grãos do milho safrinha, em sucessão à soja, independentemente da fonte utilizada.

Efeito da introdução de resíduo de cinza de forno cerâmico em massa para cerâmica estrutural

The red ceramics and structural ceramics, as they are known, include ceramic materials made by blocks of seals and structures, bricks, tiles, smail flagstones manacles, rustic floors and ornamental materials. Their fabrication uses raw material such as clay and clay sites, with some content of impurity. It has good durability and mechanical strength to compression, low cost, making it one of the mainly used materials in civil engineering. The incorporation of many industrial activities residue to ceramic products is a technological alternative for reducing the environmental impact caused by its carefree disposal. This incorporation can promote chemical change and inertness of metals from residue, by fixation in the glassy phase of ceramic during the burning stage. The main aim of this project is to study the technical feasibility of the addition of ceramic oven ash into formulations of mass for structural ceramics. In this project two kinds of clay (plastic and non-plastic) were used, as well as the ash from firewood used in the process of burning of structural ceramics. A group of experiments was outlined, which permitted the evaluation of the influence of the burning cycle in different temperatures of the ash content in formulations for ceramic blocks through technological properties, mechanical behavior and microstructure. Five samples were processed of each one of the masses of plastic and non-plastic clay without addition of ash and with addition of ash on the percentages of 10 % and 20 %, for temperatures of 850 °C, 950 °C, 1050 °C and 1150 °C, obtained through sinterization process. Among the studied compositions, the one which presented best performance was the mass of clay with 10 % of ash, at temperature of 1150 °C, with the smallest absorption of water, the smallest apparent porosity, specific apparent mass a bit over the others and greatest mechanical resistance to flexion. The composition made confirmed the technical feasibility of the use of ash in the mass for structural ceramics with maintenance of its necessary characteristics for its purposes

Desempenho de cultivares transgênicas de soja em sucessão a culturas de inverno em semeadura direta

The objective of this research was to evaluate crop yield and some characteristics and yield components of transgenic soybean cultivars sown after different winter cover crops in the first year under no tillage system. The experimental design was the completely randomized block with split plots and four replications. The main plots consisted of five winter cover crops, white oat (Avena sativa L.), forage turnip (Raphanus sativus L.), barley (Hordeum vulgare L.), wheat (Triticum aestivum L.) and ground pea (Pisum sativum L.) and an area under fallow (spontaneous vegetation). The subplots consisted of six soybean cultivars (BRS 243 RR, BRS 245 RR, BRS 247 RR, BRS 255 RR, BRS 256 RR and BRS 244 RR). Variance analysis for agronomic characteristics showed that soybean yield components were influenced by the interaction between winter crop and soybean cultivar. Thus, final population, number of nodes and pods per plant, nodes dry matter per plant, number of grains per pod and grain yield were affected significantly. When soybean nodulation was evaluated, the treatment with the area under fallow showed lower values. There was difference among winter crops for BRS 243 RR grain yield, white oat showed the highest values.

Desempenho de três variedades de soja na região dos tabuleiros costeiros no estado Alagoas

The objective of this work, the performance of three varieties of soybean on "Tabuleiros Costeiros" State of Alagoas. The installation of the experiment occurred on March 20, 2006, picking up the parcels on 26 August 2006. The experimental design was a randomized blocks with seven repetitions. The experimental plots consisted of ten rows of 4.0 m in length, spaced 0.50 m. In ten plants per plot were marked certain height of the plant in full bloom stage R2 and point of harvest stage R9 considering the distance between the soil surface and apical end of the main stem, the body weight of 100 seeds, grain production and dry weight in (kg ha(-1)) which are calculated from the production harvested per plot. The soybean plants of three varieties showed height below the minimum required for mechanical harvesting. The three varieties yield or more of the traditionally producing. The average of dry matter accumulation obtained show the variety BRS Tracaja as a good option for the production of forage.

Nitrogênio em cobertura, teor de proteína e exportação de nutrientes pelos grãos de painço

Knowledge of the mineral composition of grain and export of nutrients by the proso millet is important to enhance their use and promote more rational fertilizer recommendations. This work aimed to evaluate the protein and nutrients in the grain and export of macronutrient by the proso millet, cv. AL Tibagi, submitted to different doses and times of nitrogen top-dressing application. The experimental design was randomized block design in a 4x2 factorial scheme, constituted by four doses (0, 30, 60, and 120 kg ha(-1) of N) and two application times (14 and 28 days after emergency) of N fertilizer (urea) in top-dressing with four replications. Nitrogen top-dressing application increased grain yield and N content and protein in grains of proso millet, however, reduced the concentration of K. Nitrogen top-dressing fertilization increased the export of N, P, Ca, Mg and S for the grains of proso millet. Proso millet exported an average of macronutrients in the following order: 28.1 kg ha(-1) N; 3.4 kg ha(-1) P; 2.1 kg ha(-1) Ca; 1.4 kg ha(-1) S, 0.9 kg ha(-1) K and 0.8 kg ha(-1) Mg.

Efeito de glyphosate sobre características produtivas em cultivares de soja transgênica e convencional

The aim of this work was to evaluate the grain yield of two soybean cultivars (CD-216 and CD-212RR, divided into three stages: (i) to evaluate the effect of components of production, of simulated drift of glyphosate throught subdoses (1,3; 2,6; 5,3; 11,5 and 22,5 g e. a. ha(-1)) of two cultivars; (ii) to evaluate the influence of glyphosate (720; 1080; 1440 and 1800 g e. a. ha(-1)) in the transgenic soybean yield The experiments carried out in experimental area in the school farm of Uniderp, city of Dorados, MS ina typical Rhodic Haplustox. The experimental design used was in blocks to perhaps The parameters were: heigh oh the pln\ant, number of pods per plants, number of seeds per pod, masss of 100 grains, grain yield (%) of germination, dry mass of seedling, the lengh of radical and air part. The cultivate CD-212RR was not influenced by the subdoses application of glyphosate. Effect of growth stimulus was not observerd due to application of glyphosate subdoses in both cultivars in field conditions. Doses from 11,25 g e. a. ha(-1) caused60 of phytotoxicity in CD-216, at 28 DAA reduce production by 33%. The height and number of pods per plant of cultivar CD-212RR have been reduced and productivity decrease 21% with the application of 1.800 g e.a.ha(-1) of glyphosate.

Modelagem numérica de escoamento em padrão anular com transferência de calor e massa

Annular flow is the prevailing pattern in transport and energy conversion systems and therefore, one of the most important patterns in multiphase flow in ducts. The correct prediction of the pressure gradient and heat transfer coefficient is essential for optimizing the system s capacity. The objective of this work is to develop and implement a numerical algorithm capable of predicting hydrodynamic and thermal characteristics for upflow, vertical, annular flow. The numerical algorithm is then complemented with the physical modeling of phenomena that occurs in this flow pattern. These are, turbulence, entrainment and deposition and phase change. For the development of the numerical model, axial diffusion of heat and momentum is neglected. In this way the time-averaged equations are solved in their parabolic form obtaining the velocity and temperature profiles for each axial step at a time, together with the global parameters, namely, pressure gradient, mean film thickness and heat transfer coefficient, as well as their variation in the axial direction. The model is validated for the following conditions: fully-developed laminar flow with no entrainment; fully developed laminar flow with heat transfer, fully-developed turbulent flow with entrained drops, developing turbulent annular flow with entrained drops, and turbulent flow with heat transfer and phase change

Estudo de formulação de massa para aplicação em placas cerâmicas

The sector of civil construction is strongly related to the red ceramic industry. This sector uses clay as raw material for manufacturing of various products such as ceramic plates. In this study, two types of clay called clay 1 and clay 2 were collected on deposit in Ielmo Marinho city (RN) and then characterized by thermogravimetric analysis (TG/DTG), differential thermal analysis (DTA), X-ray diffraction (XRD), X-ray fluorescence (XRF), rational analysis and particle size distribution and dilatometric analyses. Ceramic plates were manufactured by uniaxial pressing and by extrusion. The plates obtained by pressing were produced from the four formulations called 1, 2, 3 and 4, which presented, respectively, the following proportions by mass: 66.5% clay 1 and 33.5% clay 2, 50% clay 1 and 50% clay 2, 33.5% clay 1 and 66.5% clay 2, 25% clay 1 and 75% clay 2. After firing at 850, 950 and 1050 °C with heating rate of 10 °C/min and soaking time of 30 minutes, the following technological properties were determined: linear firing shrinkage, water absorption, apparent porosity, apparent specific mass and tensile strength (3 points). The formulation containing 25% clay 1 produced plates with most satisfactory results of water absorption and mechanical resistance, because of that it was chosen for manufacturing plates by extrusion. A single firing cycle was established for these plates, which took place as follow: heating rate of 2 °C/min up to 600 ºC with soaking time of 60 minutes, followed by heating using the same rate up to 1050 ºC with soaking time of 30 minutes. After this cycle, the same technological properties investigated in the plates obtained by pressing were determined. The results indicate (according to NRB 13818/1997) that the plates obtained by pressing from the mixture containing 25 wt% clay 1, after firing at 1050 °C, reach the specifications for semi-porous coating (BIIb). On the other hand, the plates obtained by extrusion were classified as semi-stoneware (group AIIa)