Vacuum ultraviolet optical properties of (La,Gd)PO4 : RE3+ (RE = Eu, Tb)

Vacuum ultraviolet excitation spectra of phosphors (La,Gd)PO4:RE3+ (RE = Eu or Tb) and X-ray photoelectron spectra of LaPO4 and GdPO4 are investigated. The vacuum ultraviolet excitation intensity of (La,Gd)PO4:RE3+ is enhanced with the increasing of Gd3+ content, which implies that Gd3+ plays an intermediate role in energy transfer from host absorption band to RE3+. When Gd3+ is doped into LaPO4:Eu, charge transfer band (CT band) begins to shift to higher energy region and the overlap degree of CT band and the host absorption band gets greater with more Gd3+ doped into LaPO4. These results suggest that the dopant (Gd3+) gives an important influence on energy transfer efficiency. The top of LaPO4 valance band is formed by the 2p level of O2-, whereas that of GdPO4 valance band is formed by the 2p level of O2- and the 4f level of Gd3+, showing the differences in band structures between LaPO4 and GdPO4.

Direct measurement of plowing friction and wear of a polymer thin film using the atomic force microscope

Nanometer-scale plowing friction and wear of a polycarbonate thin film were directly measured using an atomic force microscope (AFM) with nanoscratching capabilities. During the nanoscratch tests, lateral forces caused discrepancies between the maximum forces for the initial loadings prior to the scratch and the unloading after the scratch. In the case of a nanoscratch test performed parallel to the cantilever probe axis, the plowing friction added another component to the moment acting at the cantilevered end compared to the case of nanoindentation, resulting in an increased deflection of the cantilever. Using free-body diagrams for the cases of nanoindentation and nanoscratch testing, the AFM force curves were analyzed to determine the plowing friction during nanoscratch testing. From the results of this analysis, the plowing friction was found to be proportional to the applied contact force, and the coefficient of plowing friction was measured to be 0.56 +/- 0.02. Also, by the combination of nanoscratch and nanoindentation testing, the energetic wear rate of the polycarbonate thin film was measured to be 0.94 +/- 0.05 mm(3)/(N m).

The effect of formulated molecular weight on temperature resistance and mechanical properties in polyimide based composites

This experimental study examines the role of formulated molecular weight between crosslink sites on the temperature resistance and mechanical properties of composites based on a polyimide containing a diphenyl thioether unit (PTI). The composites are fabricated by in situ polymerization of monomer reactants (PMR) using three monomeric ingredients: bis(3,4-dicarboxyphenyl) sulfide dianhydride (TDPA); 4,4'-methylene dianiline (MDA); and the monomethyl ester of norbornene anhydride (NE). By changing monomeric molar ratio, three formulations are prepared, in which formulated molecular weight between crosslink sites varies from 1487 to 3446 g mol(-1). Unidirectional composite laminates from each formulation and T300 carbon fibres are compression moulded and cut into a series of test specimens. By measuring the glass transition temperature (T-g), Mode I interlaminar fracture toughness (G(IC)) and other mechanical properties at room and elevated temperatures, the influences of formulated molecular weight on the temperature resistance and mechanical properties of PTI-based composites are investigated.

NMR investigation of phenolphthalein polyether ether ketone .1. The chain structure and assignments of H-1, C-13 NMR lines of PEK-C

Amorphous samples of polyether ketone with cardo(PEK-C) have been studied in the solution state by C-13, H-1 high-resolution NMR, The H-1 and C-13 1D NMR spectra were assigned using two dimensional chemical shift correlated spectroscopy, 2D homonuclear correlated(COSY) and heteronuclear correlated (HETCOR) spectroscopy present important information. In this work, the structural units of PEK-C was determined by NMR. For some peaks, these assignments are confirmed by two dimensional long-range heteronuclear correlation experiments, A little modification is made on the original C-13 peak assignments for the main chain, The symmetry and the isotacticity of the chain structure for PEK-C are obvious on NMR data.

酞侧基聚芳醚酮的核磁共振研究（Ⅰ）──链结构及NMR谱的归属

用１Ｄ　ＮＭＲ方法研究酞侧基聚芳醚酮（ＰＥＫ－Ｃ）链结构，用二维同核化学位移相关与二维异核化学位移相关实验方法对１Ｄ　ＮＭＲ谱峰进行归属，探讨了二维异核远程相关实验在缩聚高分子研究中的应用，为ＰＥＫ－Ｃ修饰机理以及共混相容机理的研究提供重要信息。溶液ＮＭＲ谱图数据表明，ＰＥＫ－Ｃ具有较规整的链结构。

SYNTHESIS AND CRYSTAL-STRUCTURE OF [ME4C2CP2SMCL-CENTER-DOT-THF]2

Me4C2(C5H4MgCl)2(THF) (THF = tetrahydrofuran) reacts with anhydrous SmCl3 in THF to give [Me4C2CP2SMCl.THF]2. The molecule is a dimer. Sm1 and Sm2 are bridged unsymmetrically by two chlorine atoms [Sm(1)-CI(1) 2.787(2), Sm(1)-Cl(2) 2.848(2), Sm(2)-Cl(1) 2

海洋环境中有机锡的形态分析及其代谢降解研究

有机锡化合物被广泛用作塑料制品中的稳定剂、船舶油漆的防污剂、工业催化剂、农林业杀虫杀菌剂以及用于木材的防腐保存等，已经引起严重的环境污染。世界上许多国家纷纷制定相应的法规对其使用加以禁止或限制。我国目前还没有明确的限制有机锡使用的法律法规，缺少有机锡污染的第一手资料，更没有长期的控制、监测与研究计划。由于有机锡的种类繁多，理化性质存在差别，所以在提取、分离和测定中均存在较大的困难。从我国这方面己有的工作来看，缺乏各种高选择性的分离方法和高灵敏度的检测方法是制约这项研究广泛开展的原因之一。有机锡的痕量与超痕量分析技术是当今环境和食品安全分析领域的前沿技术。 本论文利用高效液相色谱和电感耦合等离子体质谱联用技术建立了海洋环境中多种有机化合物的同时快速检测方法；发展了多种海洋环境样品中有机锡的前处理技术；研究了有机锡在海洋生物中的分布、代谢及降解过程中化学形态的变化；同时发展了海洋环境中多种痕量元素的快速检测方法。所建立的高效液相色谱和电感耦合等离子体质谱联用技术可同时、快速分析5种有机锡的形态(三甲基锡TMT、二苯基锡DPhT、二丁基锡DBT、三丁基锡TBT和三苯基锡TPhT)，其检出限均低于0.3μg/L。 用所建立方法对南海海洋生物样品中的有机锡污染进行了研究，利用SPSS软件对检测结果进行了探讨，发现在所研究海洋生物样品的97.2%中可检出丁基锡和苯基锡化合物，其浓度分布处于该化合物检出限～1487.8ng/g范围内。其中，贝类样品中总有机锡的平均浓度为416.9ng/g，远远高于鱼类样品中总有机锡的平均浓度（211.9ng/g）。海洋生物中存在高浓度的有机锡说明本海域有机锡污染严重，已经对生态环境造成了严重影响，危害到人类生活。其主要的污染源是防污涂料的应用，目前紧迫的问题是采取必要的措施来控制有机锡的使用。 本工作建立了海水样品和沉积物样品中五种有机锡的简单快速萃取方法。采用加入2%的环庚三烯酚（tropolone）的二氯甲烷CH2Cl2对海水中的有机锡进行萃取，大大提高了有机锡的萃取率，减少了萃取的时间，二苯基锡（DPhT）、二丁基锡（DBT）、三丁基锡（TBT）和三苯基锡（TPhT）的萃取率均在80%以上，仅三甲基锡（TMT）的萃取率较低（在50%左右），究其原因，可能是因为在萃取的过程中三甲基锡（TMT）产生了降解。采用流动相和0.2%环庚三烯酚酮（tropolone）对沉积物国际标准物质PACS-2进行超声萃取及高速离心后，用所建方法进行了分析。结果表明，测定值与标准值吻合。研究表明，所建立的方法可用于实际环境沉积物中有机锡的形态分析。 本文建立了流动注射与电感耦合等离子体质谱联用技术直接同时测定海水中多种痕量元素的方法。该方法采用痕量进样技术，能够有效地减少海水中Na，Mg, Ca和Cl等大量基体元素对待测痕量元素测定的干扰，减少这些元素在电感耦合等离子体采样锥上的盐沉积，可以同时测量海水中的V、Cr、Mn、Fe、Co、Ni、Cu、Zn、As、Mo、Cd、Pb，Hg和U等痕量级元素。用所建的方法测定南海海域海水中的重金属元素，发现Cd，Cr，As等有毒有害元素的污染很轻，均符合Ⅰ级海水的限量。 在海洋沉积物样品处理研究中，本工作改进了不需要赶走HF酸就可以对沉积物消解完全的密闭容器消解法，由于减少了赶走HF酸的步骤，使消解的时间由原来的二十个小时降低为十个小时，大大降低了消解的时间。采用该样品消解方法，并用ICP-MS测定了南黄海海域沉积物中锡及其他重金属元素的含量。建立了微波消解-ICP-MS测定海洋生物中锡、砷、镉、汞及铅等有害重金属元素的分析方法，并用于南黄海7个及南海海域29个海产品中的测定。测定结果表明海洋生物中上述有毒有害元素有不同程度的超标问题；不同种类，不同产地的海洋生物中重金属元素的含量有一定的差别，这些研究结果为海产品安全质量控制提供了有价值的科学信息。 在上述各章工作的基础上，本文研究了有机锡在海洋生物中的分布、代谢及降解过程，并初步建立了高效液相-电喷雾-飞行时间质谱（LC-APCI-TOF-MS）测定有机锡的方法，可对未知的有机锡化合物进行结构表征。有机锡在贝类中不同的组织显示，其内脏中有机锡的含量高于肌肉中有机锡含量。常规的煮、炸、蒸及微波的烹饪方式并不能降解海产品中的有机锡化合物。

高效液相色谱-蒸发光散射检测法测定那保胶囊中黄芪甲苷含量

目的：采用高效液相-蒸发光散射检测器（HPLC-ELSD）法测定藏药那保胶囊中黄芪甲苷的含量。方法：色谱柱为KromasilC_(18)柱（4．6mm×250mm，5μm）；流动相为乙腈-水（36：64）；ELSD（蒸发光散射检测器）检测。结果：黄芪甲苷在1-10μg范围内具良好的线性关系（r=0．999），平均回收率为99．05，RSD为2．48％。结论：该法简便可行，重复性好，适用于那保胶囊的质量控制。

Global negative vegetation feedback to climate warming responses of leaf litter decomposition rates in cold biomes

Whether climate change will turn cold biomes from large long-term carbon sinks into sources is hotly debated because of the great potential for ecosystem-mediated feedbacks to global climate. Critical are the direction, magnitude and generality of climate responses of plant litter decomposition. Here, we present the first quantitative analysis of the major climate-change-related drivers of litter decomposition rates in cold northern biomes worldwide. Leaf litters collected from the predominant species in 33 global change manipulation experiments in circum-arctic-alpine ecosystems were incubated simultaneously in two contrasting arctic life zones. We demonstrate that longer-term, large-scale changes to leaf litter decomposition will be driven primarily by both direct warming effects and concomitant shifts in plant growth form composition, with a much smaller role for changes in litter quality within species. Specifically, the ongoing warming-induced expansion of shrubs with recalcitrant leaf litter across cold biomes would constitute a negative feedback to global warming. Depending on the strength of other (previously reported) positive feedbacks of shrub expansion on soil carbon turnover, this may partly counteract direct warming enhancement of litter decomposition.

机器人机械手的离散时间学习控制

本文为机器人机械手提出了一种基于离散时间的重复学习控制法，这种学习控制法利用机器人动力学模型的部分知识，从它的特性和实用观点看，这种控制法比现有的其它学习控制法更有吸引力．本文还给出了学习控制法的收敛性证明和计算机仿真结果。

企业综合自动化系统体系结构

阐述了一般综合自动化系统的二维层次体系结构，以及系统的功能、信息、资源、组织四视图在三个层次的内涵及相互关系。

生活垃圾填埋场是大气汞的重要来源

生活垃圾中含有汞的废弃物、垃圾焚烧已成为西方发达国家最主要的人为大气排放汞源.在中国垃圾填埋是处理城市生活垃圾的最主要方式.利用高时间分辨率大气自动测汞仪对贵阳市郊区高雁垃圾卫生填埋场排气筒气态总汞进行了测定;利用气相色谱与冷原子荧光联用技术测定了排气筒中的单甲基汞和二甲基汞的含量.同时运用大气自动测汞仪与低空白石英玻璃通量箱结合技术高时间分辨率测定了裸露垃圾及填埋场土壤与大气间气态总汞的交换通量.垃圾填埋半年区的排气筒气态总平均浓度为(665.52±291.25)ng/m,与贵阳市某小型燃煤锅炉排放烟气的总汞含量相当,排气筒气体中的单甲基汞

混凝—臭氧氧化预处理垃圾渗滤液的实验研究

利用以水玻璃、硫酸、硫酸铝和废铁屑为原料研制出的聚硅酸硫酸铝铁类混凝剂（PSAFCS），结合臭氧氧化预处理某垃圾填埋场渗滤液。实验结果表明，经过该处理工艺，垃圾渗滤液CODCr去除率达70.6%，BOD5去除率达75.4%，色度去除率为94%，说明该方法是行之有效的。

万山汞矿区地表与大气界面间汞交换通量研究

采用动力学通量箱与高时间分辨率大气自动测汞仪联用技术对万山汞矿区不同季节、不同地表与大气界面间汞交换通量和大气汞含量进行了测定. 结果显示,受人为活动和地表强烈释汞的影响,万山地区大气汞含量高出背景区1～3 个数量级,在冶炼厂附近平均值可达1 10118 ng/ m3 ,最低平均值达1718 ng/ m3 ,显示万山汞矿区已遭受较严重的大气汞污染. 万山汞矿区土壤与大气界面汞交换非常强烈,土壤向大气的释汞通量最高可达27 827 ng/ (m2·h) ,大气汞干沉降通量最高可达9 434ng/ (m2·h) . 万山汞矿区土壤与大气汞交换通量主要受光照强度、大气汞含量影响. 光照在土壤释汞过程中起促进作用,而较高的大气汞含量则抑制了土壤向大气的释放,并导致大气汞强烈的干沉降. 不同的地表类型对地表释汞影响较大,植被覆盖土壤释汞通量显著低于无植被覆盖地区,而冶炼后的矿渣堆则成为大气汞的净源.