Friction Stir Processing : a new microstructure improvement technique

In the present work, microstructure improvement using FSP (Friction Stir Processing) is studied. In the first part of the work, the microstructure improvement of as-cast A356 is demonstrated. Some tensile tests were applied to check the increase in ductility. However, the expected results couldn’t be achieved. In the second part, the microstructure improvement of a fusion weld in 1050 aluminium alloy is presented. Hardness tests were carried out to prove the mechanical propertyimprovements. In the third and last part, the microstructure improvement of 1050 aluminium alloy is achieved. A discussion of the mechanical property improvements induced by FSP is made. The influence of tool traverse speed on microstructure and mechanical properties is also discussed. Hardness tests and recrystallization theory enabled us to find out such influence

Large fluctuations in the disassembly rate of microtubules revealed by atomic force microscopy.

Atomic force microscopy (AFM) in situ has been used to observe the cold disassembly dynamics of microtubules at a previously unrealised spatial resolution. Microtubules either electrostatically or covalently bound to aminosilane surfaces disassembled at room temperature under buffer solutions with no free tubulin present. This process was followed by taking sequential tapping-mode AFM images and measuring the change in the microtubule end position as a function of time, with an spatial accuracy down to +/-20nm and a temporal accuracy of +/-1s. As well as giving average disassembly rates on the order of 1-10 tubulin monomers per second, large fluctuations in the disassembly rate were revealed, indicating that the process is far from smooth and linear under these experimental conditions. The surface bound rates measured here are comparable to the rates for GMPCPP-tubulin microtubules free in solution, suggesting that inhibition of tubulin curvature through steric hindrance controls the average, relatively low disassembly rate. The large fluctuations in this rate are thought to be due to multiple pathways in the kinetics of disassembly with differing rate constants and/or stalling due to defects in the microtubule lattice. Microtubules that were covalently bound to the surface left behind the protofilaments covalently cross-linked to the aminosilane via glutaraldehyde during the disassembly process. Further work is needed to quantitatively assess the effects of surface binding on protofibril disassembly rates, reveal any differences in disassembly rates between the plus and minus ends and to enable assembly as well as disassembly to be imaged in the microscope fluid cell in real-time.

Determination of the direct band-gap energy of InAlAs matched to InP by photoluminescence excitation spectroscopy

A series of InxAl1-xAs samples (0.51≪x≪0.55)coherently grown on InP was studied in order to measure the band-gap energy of the lattice matched composition. As the substrate is opaque to the relevant photon energies, a method is developed to calculate the optical absorption coefficient from the photoluminescence excitation spectra. The effect of strain on the band-gap energy has been taken into account. For x=0.532, at 14 K we have obtained Eg0=1549±6 meV

Direct visualization of the trimeric structure of the ASIC1a channel, using AFM imaging.

There has been confusion about the subunit stoichiometry of the degenerin family of ion channels. Recently, a crystal structure of acid-sensing ion channel (ASIC) 1a revealed that it assembles as a trimer. Here, we used atomic force microscopy (AFM) to image unprocessed ASIC1a bound to mica. We detected a mixture of subunit monomers, dimers and trimers. In some cases, triple-subunit clusters were clearly visible, confirming the trimeric structure of the channel, and indicating that the trimer sometimes disaggregated after adhesion to the mica surface. This AFM-based technique will now enable us to determine the subunit arrangement within heteromeric ASICs.

δ 15N measurement of organic and inorganic substances by EA-IRMS: a speciation-dependent procedure

Little attention has been paid so far to the influence of the chemical nature of the substance when measuring δ 15N by elemental analysis (EA)-isotope ratio mass spectrometry (IRMS). Although the bulk nitrogen isotope analysis of organic material is not to be questioned, literature from different disciplines using IRMS provides hints that the quantitative conversion of nitrate into nitrogen presents difficulties. We observed abnormal series of δ 15N values of laboratory standards and nitrates. These unexpected results were shown to be related to the tailing of the nitrogen peak of nitrate-containing compounds. A series of experiments were set up to investigate the cause of this phenomenon, using ammonium nitrate (NH4NO3) and potassium nitrate (KNO3) samples, two organic laboratory standards as well as the international secondary reference materials IAEA-N1, IAEA-N2-two ammonium sulphates [(NH4)2SO4]-and IAEA-NO-3, a potassium nitrate. In experiment 1, we used graphite and vanadium pentoxide (V2O5) as additives to observe if they could enhance the decomposition (combustion) of nitrates. In experiment 2, we tested another elemental analyser configuration including an additional section of reduced copper in order to see whether or not the tailing could originate from an incomplete reduction process. Finally, we modified several parameters of the method and observed their influence on the peak shape, δ 15N value and nitrogen content in weight percent of nitrogen of the target substances. We found the best results using mere thermal decomposition in helium, under exclusion of any oxygen. We show that the analytical procedure used for organic samples should not be used for nitrates because of their different chemical nature. We present the best performance given one set of sample introduction parameters for the analysis of nitrates, as well as for the ammonium sulphate IAEA-N1 and IAEA-N2 reference materials. We discuss these results considering the thermochemistry of the substances and the analytical technique itself. The results emphasise the difference in chemical nature of inorganic and organic samples, which necessarily involves distinct thermochemistry when analysed by EA-IRMS. Therefore, they should not be processed using the same analytical procedure. This clearly impacts on the way international secondary reference materials should be used for the calibration of organic laboratory standards.

Increase of grain and green matter of corn by liming

Despite the fact that aluminum toxicity to crops is eliminated near soil water pH of 5.5, lime recommendation in many regions aims to increase soil pH up to 6.0 or even higher. For highly buffered soils, high rates of limestone are required to raise the pH from 5.5 to 6.0, resulting in additional, sometimes unnecessary, costs. The objective of this study was to evaluate the effect of soil pH on corn yield in a very acid Hapludox. The experiment was carried out in Lages, Southern Brazil, from 1992 to 1996. The soil had water pH of 4.7, Al3+ of 33 mmol c kg-1, O.M. of 45 g kg-1 and lime requirement to pH 6.0 of 9.0 t ha-1. Dolomitic limestone at rates of 0, 4.5, 9.0, 13.5 and 18.0 t ha-1 (equivalent to pure CaCO3) was incorporated into the soil down to 17 cm depth, in 1992. Liming increased linearly the values of soil pH (from 4.7 to 6.6) and Ca and Mg, eliminated Al3+ with rates of 9.0 t ha-1 or higher, decreased slightly Al-CuCl2, Fe and Cu, and did not affect Zn and Mn. Maximum average corn yield for grain (7.9 t ha-1) and for green matter for silage (GM) (59 t ha-1) was obtained, respectively, at soil pH of 6.0 (12 t ha-1 of limestone) and of 6.1 (14 t ha-1 of limestone); maximum economic efficiency for grain was obtained at pH 5.6 (7.5 t ha-1 of limestone). Maximum yield increments due to liming were 17% for grain and 20% for GM.

Iron oxides in plinthic soils on sedimentary deposits in northeastern Brazil

This study was conducted to examine the distribution and nature of Fe oxides in plinthic soils on the sediments of Barreiras Group (in the state of Piauí) and Itapecuru Formation (in the state of Maranhão) in Northeastern Brazil. Four pedons were selected: a "plinthic, dystrophic, epieutrophic Gray Podzolic with low activity clay" and a "dystrophic Plinthosol with low activity clay" (both Plinthic Kandiustalfs) on the Barreiras sediments, as well as an "eutrophic Plinthosol with low activity clay" and an "allic Plinthosol with low activity clay" (both Plinthustalfs) on the Itapecuru sediments. Soil samples were fractionated into > 2 mm (pisoliths), water-stable aggregates (plinthite) and matrices; the aggregates and matrices were further fractionated into sand, silt and clay sizes. Dithionite extractable iron (Fe d) and aluminum (Al d), as well as oxalate extractable iron (Fe o), were determined for all fractions, and X-ray diffraction analyses were performed on the pisoliths. It was observed that the Plinthustalfs contain more iron oxides, exhibit more extensive plinthite development and have a greater potential for further plinthite development than the Kandiustalfs. The distribution of values for the Fe d indicates that plinthite formation and induration in all soils were accompanied by an enrichment of Fe oxides in all particle size fractions. This Fe segregation was accompanied by aggregation of particles leading to a greater degree of crystallinity, as indicated by analysis of the ratios of Al d:Fe d. Larger ratios of goethite to hematite, and relatively smaller amounts of silicates in the more mature pisoliths were revealed by X-ray diffraction analysis. Ratios of Al d:Fe d were larger in the Kandiustalfs than in the Plinthustalfs, and also larger than expected for Al-substituted Fe oxides. According to ratios of Al d:Fe d, Fe mobilization in all soils has likely occurred under reducing conditions, facilitated by organic matter on the soil surface.

The inflammasomes: guardians of the body.

The innate immune system relies on its capacity to rapidly detect invading pathogenic microbes as foreign and to eliminate them. The discovery of Toll-like receptors (TLRs) provided a class of membrane receptors that sense extracellular microbes and trigger antipathogen signaling cascades. More recently, intracellular microbial sensors have been identified, including NOD-like receptors (NLRs). Some of the NLRs also sense nonmicrobial danger signals and form large cytoplasmic complexes called inflammasomes that link the sensing of microbial products and metabolic stress to the proteolytic activation of the proinflammatory cytokines IL-1beta and IL-18. The NALP3 inflammasome has been associated with several autoinflammatory conditions including gout. Likewise, the NALP3 inflammasome is a crucial element in the adjuvant effect of aluminum and can direct a humoral adaptive immune response. In this review, we discuss the role of NLRs, and in particular the inflammasomes, in the recognition of microbial and danger components and the role they play in health and disease.

Toll-like receptor 3 is necessary for dsRNA adjuvant effects.

Toll-like receptors (TLR) recognize pathogen associated molecular patterns, and the binding of their specific ligands triggers a proinflammatory response that helps to fight invading microorganisms, and can be harnessed to increase vaccine efficiency. The present study demonstrates that double-stranded RNA is a promising vaccine adjuvant able to increase both proliferation and activation of antigen-specific CD8(+) T cells. Importantly, TLR3 is required for this adjuvant effect, as TLR3 deficient recipients failed to enhance proliferation of adoptively transferred TCR transgenic CD8(+) T cells in the presence of double-stranded RNA. Finally, this study also shows that, in contrast to previous reports in humans, TLR3 does not exert direct costimulatory activity on CD8(+) T cells in mice.

The effect of nitrogen and sulphur fertilization on yield and quality of kohlrabi (Brassica oleracea, L.)

In a greenhouse pot experiment with kohlrabi, variety Luna, we explored the joint effect of N (0.6 g N per pot = 6 kg of soil) and S in the soil (25-35-45 mg kg-1 of S) on yields, on N, S and NO3- content in tubers and leaves, and on alterations in the amino acids concentration in the tubers. S fertilisation had no effect on tuber yields. The ranges of N content in tubers and leaves were narrow (between 1.42-1.48 % N and 1.21-1.35 % N, respectively) and the effect of S fertilisation was insignificant. S concentration in the tubers ranged between 0.59 and 0.64 % S. S fertilisation had a more pronounced effect on the S concentration in leaf tissues where it increased from 0.50 to 0.58 or to 0.76 % S under the applied dose. The NO3- content was higher in tubers than in leaves. Increasing the S level in the soil significantly reduced NO3- concentrations in the tubers by 42.2-53.6 % and in the leaves by 8.8-21.7 %. Increasing the S content in the soil reduced the concentration of cysteine + methionine by 16-28 %. The values of valine, tyrosine, aspartic acid and serine were constant. In the S0, S1, and S2 treatments the levels of threonine, isoleucine, leucine, arginine, the sum of essential amino acids and alanine decreased from 37 to 9 %. The histidine concentration increased with increasing S fertilisation. S fertilisation of kohlrabi can be recommended to stabilize the yield and reduce the undesirable NO3- contained in the parts used for consumption.

Efficient energy transfer from Si clusters to Er3+ in complex silicate glasses

We present an extensive study of the structural and optical emission properties in aluminum silicates and soda-lime silicates codoped with Si nanoclusters (Si-nc) and Er. Si excess of 5 and 15¿at.¿% and Er concentrations ranging from 2×1019 up to 6×1020¿cm¿3 were introduced by ion implantation. Thermal treatments at different temperatures were carried out before and after Er implantation. Structural characterization of the resulting structures was performed to obtain the layer composition and the size distribution of Si clusters. A comprehensive study has been carried out of the light emission as a function of the matrix characteristics, Si and Er contents, excitation wavelength, and power. Er emission at 1540¿nm has been detected in all coimplanted glasses, with similar intensities. We estimated lifetimes ranging from 2.5¿to¿12¿ms (depending on the Er dose and Si excess) and an effective excitation cross section of about 1×10¿17¿cm2 at low fluxes that decreases at high pump power. By quantifying the amount of Er ions excited through Si-nc we find a fraction of 10% of the total Er concentration. Upconversion coefficients of about 3×10¿18¿cm¿3¿s¿1 have been found for soda-lime glasses and one order of magnitude lower in aluminum silicates.

Correction of soil acidity in the subsurface of an oxisol with sandy loam texture under no-tillage

In Rio Grande do Sul State (RS), Southern Brazil, aluminum saturation in many areas under no-till system is high and base saturation low in the 0.10-0.20 m layer (subsurface), which may reduce the grain yield of annual crops. The objective of this study was to evaluate if the occurrence of high aluminum saturation and low base saturation in the subsurface, under a no-till system, represents a restrictive environment for crop production, as well as to evaluate forms of lime incorporation for soil acidity correction in the subsurface. For this purpose, an experiment was carried out with soybean (2005/2006), corn (2006/2007), wheat (2007) and soybean (2007/2008) crops, in a Rhodic Hapludox (USDA, 1999) with sandy loam texture, under no-till for four years in the county of Tupanciretã (RS). The six treatments were: no-tillage with and without lime, plowing with and without lime, and chiseling with and without lime. The values of pH-H2O, aluminum saturation and base saturation were evaluated 24 months after treatment application in the layers 0-0.05; 0.05-0.10; 0.10-0.15; 0.15-0.20 and 0.20-0.30 m. The yields of soybean (2005/2006), corn (2006/2007), wheat (2007) and soybean (2007/2008) were evaluated. Soil acidity in the subsurface did not affect crop yield when the acidity in the layer from 0-0.10 m was at levels for which lime application is not recommended, according to CQFSRS/SC (2004). Lime incorporation through plowing was the most efficient way of correcting acidity at deeper levels.

Remaining phosphorus estimated by pedotransfer function

Although the determination of remaining phosphorus (Prem) is simple, accurate values could also be estimated with a pedotransfer function (PTF) aiming at the additional use of soil analysis data and/or Prem replacement by an even simpler determination. The purpose of this paper was to develop a pedotransfer function to estimate Prem values of soils of the State of São Paulo based on properties with easier or routine laboratory determination. A pedotransfer function was developed by artificial neural networks (ANN) from a database of Prem values, pH values measured in 1 mol L-1 NaF solution (pH NaF) and soil chemical and physical properties of samples collected during soil classification activities carried out in the State of São Paulo by the Agronomic Institute of Campinas (IAC). Furthermore, a pedotransfer function was developed by regressing Prem values against the same predictor variables of the ANN-based PTF. Results showed that Prem values can be calculated more accurately with the ANN-based pedotransfer function with the input variables pH NaF values along with the sum of exchangeable bases (SB) and the exchangeable aluminum (Al3+) soil content. In addition, the accuracy of the Prem estimates by ANN-based PTF were more sensitive to increases in the experimental database size. Although the database used in this study was not comprehensive enough for the establishment of a definitive pedotrasnfer function for Prem estimation, results indicated the inclusion of Prem and pH NaF measurements among the soil testing evaluations as promising ind order to provide a greater database for the development of an ANN-based pedotransfer function for accurate Prem estimates from pH NaF, SB, and Al3+ values.

Different PTH response to oral peptone load and oral calcium load in patients with normocalcemic primary hyperparathyroidism, primary hyperparathyroidism, and healthy subjects.

BACKGROUND: Normocalcemic primary hyperparathyroidism (PHPT-N) is a condition that may have similar long-term implications to primary hyperparathyroidism (PHPT); however, differential diagnosis and treatment for parathyroid disorders are not clearly defined. We investigated the effect of an oral peptone and an oral calcium load on calcium-regulating hormones in PHPT-N compared with PHPT and healthy controls to provide a new potential diagnostic tool. DESIGN: Case-control study. METHODS: We evaluated serum gastrin, PTH, ionized calcium, and phosphate responses to oral calcium (1 g) and peptone (10 g) load in 22 PHPT and 20 PHPT-N patients matched for PTH serum values. Moreover, 30 healthy subjects were enrolled as controls. In 12 patients for each group, we also performed the oral peptone test adding aluminum hydroxide (AH) to suppress phosphate absorption. RESULTS: In PHPT patients, PTH increased significantly 30 min after the oral peptone load, while no significant increase was found in PHPT-N and controls. After oral calcium load, PTH remained stable in PHPT while it decreased dramatically in PHPT-N patients, and ionized calcium increased significantly in each of the three groups. Peptones plus AH induced a blunted PTH increase in the three groups. CONCLUSIONS: Considering the marked difference in PTH response elicited by peptones in PHPT compared with PHPT-N, we suggest that the oral peptone test could be added to the diagnostic evaluation of PHPT patients. In case of absent response to peptones, patients should have their serum calcium levels assessed twice a year in accordance with recent guidelines.

Reclaimed Fly Ash as Select Fill Under PCC Pavement, November 1999

With the support of the Iowa Fly Ash Affiliates, research on reclaimed fly ash for use as a construction material has been ongoing since 1991. The material exhibits engineering properties similar to those of soft limestone or sandstone and a lightweight aggregate. It is unique in that it is rich in calcium, silica, and aluminum and exhibits pozzolanic properties (i.e. gains strength over time) when used untreated or when a calcium activator is added. Reclaimed Class C fly ashes have been successfully used as a base material on a variety of construction projects in southern and western Iowa. A pavement design guide has been developed with the support of the Iowa Fly Ash Affiliates. Soils in Iowa generally rate fair to poor as subgrade soils for paving projects. This is especially true in the southern quarter of the state and for many areas of eastern and western Iowa. Many of the soil types encountered for highway projects are unsuitable soils under the current Iowa DOT specifications. The bulk of the remaining soils are Class 10 soils. Select soils for use directly under the pavement are often difficult to find on a project, and in many instances are economically unavailable. This was the case for a 4.43-mile grading (STP-S- 90(22)-SE-90) and paving project in Wapello County. The project begins at the Alliant Utilities generating station in Chillicothe, Iowa, and runs west to the Monroe-Wapello county line. This road carries a significant amount of truck traffic hauling coal from the generating station to the Cargill corn processing plant in Eddyville, Iowa. The proposed 10-inch Portland Cement Concrete (PCC) pavement was for construction directly on a Class 10 soil subgrade, which is not a desirable condition if other alternatives are available. Wapello County Engineer Wendell Folkerts supported the use of reclaimed fly ash for a portion of the project. Construction of about three miles of the project was accomplished using 10 inches of reclaimed fly ash as a select fill beneath the PCC slab. The remaining mile was constructed according to the original design to be used as a control section for performance monitoring. The project was graded during the summers of 1998 and 1999. Paving was completed in the fall of 1999. This report presents the results of design considerations and laboratory and field testing results during construction. Recommendations for use of reclaimed fly ash as a select fill are also presented.