Incidence and consequence of major bleeding in primary percutaneous intervention for ST-elevation myocardial infarction in the era of radial access: an analysis of the international randomized Acute myocardial infarction Treated with primary angioplasty and intravenous enoxaparin Or unfractionated heparin to Lower ischemic and bleeding events at short- and Long-term follow-up trial.

AIMS: The aims of the study are to compare the outcome with and without major bleeding and to identify the independent correlates of major bleeding complications and mortality in patients described in the ATOLL study. METHODS: The ATOLL study included 910 patients randomly assigned to either 0.5 mg/kg intravenous enoxaparin or unfractionated heparin before primary percutaneous coronary intervention. Incidence of major bleeding and ischemic end points was assessed at 1 month, and mortality, at 1 and 6 months. Patients with and without major bleeding complication were compared. A multivariate model of bleeding complications at 1 month and mortality at 6 months was realized. Intention-to-treat and per-protocol analyses were performed. RESULTS: The most frequent bleeding site appears to be the gastrointestinal tract. Age >75 years, cardiac arrest, and the use of insulin or >1 heparin emerged as independent correlates of major bleeding at 1 month. Patients presenting with major bleeding had significantly higher rates of adverse ischemic complications. Mortality at 6 months was higher in bleeders. Major bleeding was found to be one of the independent correlates of 6-month mortality. The addition or mixing of several anticoagulant drugs was an independent factor of major bleeding despite the predominant use of radial access. CONCLUSIONS: This study shows that major bleeding is independently associated with poor outcome, increasing ischemic events, and mortality in primary percutaneous coronary intervention performed mostly with radial access.

Gold or green: the debate on Open Access policies

The movement for open access to science seeks to achieve unrestricted and free access to academic publications on the Internet. To this end, two mechanisms have been established: the gold road, in which scientific journals are openly accessible, and the green road, in which publications are self-archived in repositories. The publication of the Finch Report in 2012, advocating exclusively the adoption of the gold road, generated a debate as to whether either of the two options should be prioritized. The recommendations of the Finch Report stirred controversy among academicians specialized in open access issues, who felt that the role played by repositories was not adequately considered and because the green road places the burden of publishing costs basically on authors. The Finch Report"s conclusions are compatible with the characteristics of science communication in the UK and they could surely also be applied to the (few) countries with a powerful publishing industry and substantial research funding. In Spain, both the current national legislation and the existing rules at universities largely advocate the green road. This is directly related to the structure of scientific communication in Spain, where many journals have little commercial significance, the system of charging a fee to authors has not been adopted, and there is a good repository infrastructure. As for open access policies, the performance of the scientific communication system in each country should be carefully analyzed to determine the most suitable open access strategy. [Int Microbiol 2013; 16(3):199-203]

Effect of dripline flushing on subsurface drip irrigation systems

The velocity of dripline flushing in subsurface drip irrigation (SDI) systems affects system design, cost, management, performance, and longevity. A 30‐day field study was conducted at Kansas State University to analyze the effect of four targeted flushing velocities (0.23, 0.30, 0.46, and 0.61 m/s) for a fixed 15 min duration of flushing and three flushing frequencies (no flushing or flushing every 15 or 30 days) on SDI emitter discharge and sediments within the dripline and removed in the flushing water. At the end of the field experiment (371 h), the amount of solids carried away by the flushing water and retained in every lateral were determined as well as laboratory determination of emitter discharge for every single emitter within each dripline. Greater dripline flushing velocities, which also resulted in greater flushing volumes, tended to result in greater amounts of solids in the flushing water, but the differences were not always statistically significant. Neither the frequency of flushing nor the interaction of flushing frequency and velocity significantly affected the amount of solids in the flushing water. There was a greater concentration of solids in the beginning one‐third of the 90 m laterals, particularly for treatments with no flushing or with slower dripline flushing velocities. As flushing velocity and concurrently flushing volume increased, there was a tendency for greater solids removal and/or more equal distribution within the dripline. At the end of the field study, the average emitter discharge as measured in the laboratory for a total of 3970 emitters was 0.64 L/h. which was significantly less (approximately 2.5%) than the discharge for new and unused emitters. Only six emitters were nearly or fully clogged, with discharges between 0% and 5% of new and unused emitters. Flushing velocity and flushing frequency did not have consistent significant effects on emitter discharge, and those numerical differences that did exist were small (<3%). Emitter discharge was approximately 3% less for the distal ends of the driplines (last 20% of the dripline). Although not a specific factor in the study, the results of solids removals during flushing and solids retention within the different dripline sections suggest that duration of flushing may be a more cost‐effective management option than increasing the dripline flushing velocity through SDI system design. Finally, although microirrigation system components have been improved over the years, the need for flushing to remove solids and reduce clogging potential has not been eliminated

On the use of an appropriate TdT-mediated dUTP-biotin nick end labeling assay to identify apoptotic cells.

Apoptosis is an essential cellular mechanism involved in many processes such as embryogenesis, metamorphosis, and tissue homeostasis. DNA fragmentation is one of the key markers of this form of cell death. DNA fragmentation is executed by endogenous endonucleases such as caspase-activated DNase (CAD) in caspase-dependent apoptosis. The TUNEL (TdT-mediated dUTP-biotin nick end labeling) technique is the most widely used method to identify apoptotic cells in a tissue or culture and to assess drug toxicity. It is based on the detection of 3'-OH termini that are labeled with dUTP by the terminal deoxynucleotidyl transferase. Although the test is very reliable and sensitive in caspase-dependent apoptosis, it is completely useless when cell death is mediated by pathways involving DNA degradation that generates 3'-P ends as in the LEI/L-DNase II pathway. Here, we propose a modification in the TUNEL protocol consisting of a dephosphorylation step prior to the TUNEL labeling. This allows the detection of both types of DNA breaks induced during apoptosis caspase-dependent and independent pathways, avoiding underestimating the cell death induced by the treatment of interest.

Paediatric end-of-life care needs in Switzerland: current practices, and perspectives from parents and professionals. A study protocol.

AIM: To present a protocol for a multi-phase study about the current practice of end-of-life care in paediatric settings in Switzerland. BACKGROUND: In Switzerland, paediatric palliative care is usually provided by teams, who may not necessarily have specific training. There is a lack of systematic data about specific aspects of care at the end of a child's life, such as symptom management, involvement of parents in decision-making and family-centred care and experiences and needs of parents, and perspectives of healthcare professionals. DESIGN: This retrospective nationwide multicentre study, Paediatric End-of-LIfe CAre Needs in Switzerland (PELICAN), combines quantitative and qualitative methods of enquiry. METHODS: The PELICAN study consists of three observational parts, PELICAN I describes practices of end-of-life care (defined as the last 4 weeks of life) in the hospital and home care setting of children (0-18 years) who died in the years 2011-2012 due to a cardiac, neurological or oncological disease, or who died in the neonatal period. PELICAN II assesses the experiences and needs of parents during the end-of-life phase of their child. PELICAN III focuses on healthcare professionals and explores their perspectives concerning the provision of end-of-life care. CONCLUSION: This first study across Switzerland will provide comprehensive insight into the current end-of-life care in children with distinct diagnoses and the perspectives of affected parents and health professionals. The results may facilitate the development and implementation of programmes for end-of-life care in children across Switzerland, building on real experiences and needs. TRIAL REGISTRATION: ClinicalTrials.gov Identifier: NCT01983852.

Systematic evaluation of matrix effects in hydrophilic interaction chromatography versus reversed phase liquid chromatography coupled to mass spectrometry.

Reversed phase liquid chromatography (RPLC) coupled to mass spectrometry (MS) is the gold standard technique in bioanalysis. However, hydrophilic interaction chromatography (HILIC) could represent a viable alternative to RPLC for the analysis of polar and/or ionizable compounds, as it often provides higher MS sensitivity and alternative selectivity. Nevertheless, this technique can be also prone to matrix effects (ME). ME are one of the major issues in quantitative LC-MS bioanalysis. To ensure acceptable method performance (i.e., trueness and precision), a careful evaluation and minimization of ME is required. In the present study, the incidence of ME in HILIC-MS/MS and RPLC-MS/MS was compared for plasma and urine samples using two representative sets of 38 pharmaceutical compounds and 40 doping agents, respectively. The optimal generic chromatographic conditions in terms of selectivity with respect to interfering compounds were established in both chromatographic modes by testing three different stationary phases in each mode with different mobile phase pH. A second step involved the assessment of ME in RPLC and HILIC under the best generic conditions, using the post-extraction addition method. Biological samples were prepared using two different sample pre-treatments, i.e., a non-selective sample clean-up procedure (protein precipitation and simple dilution for plasma and urine samples, respectively) and a selective sample preparation, i.e., solid phase extraction for both matrices. The non-selective pretreatments led to significantly less ME in RPLC vs. HILIC conditions regardless of the matrix. On the contrary, HILIC appeared as a valuable alternative to RPLC for plasma and urine samples treated by a selective sample preparation. Indeed, in the case of selective sample preparation, the compounds influenced by ME were different in HILIC and RPLC, and lower and similar ME occurrence was generally observed in RPLC vs. HILIC for urine and plasma samples, respectively. The complementary of both chromatographic modes was also demonstrated, as ME was observed only scarcely for urine and plasma samples when selecting the most appropriate chromatographic mode.

Evolution: the end of an ancient asexual scandal.

Bdelloid rotifers were believed to have persisted and diversified in the absence of sex. Two papers now show they exchange genes with each other, via horizontal gene transfers as known in bacteria and/or via other forms of non-canonical sex.

Managing the Front End of Innovation in a Networked Company Environment - Combining Strategy, Processes and Systems of Innovation

The objective of the thesis is to enhance the understanding about the management of the front end phases of the innovation process in a networked environment. The thesis approaches the front end of innovation from three perspectives, including the strategy, processes and systems of innovation. The purpose of the use of different perspectives in the thesis is that of providing an extensive systemic view of the front end, and uncovering the complex nature of innovation management. The context of the research is the networked operating environment of firms. The unit of analysis is the firm itself or its innovation processes, which means that this research approaches the innovation networks from the point of view of a firm. The strategy perspective of the thesis emphasises the importance of purposeful innovation management, the innovation strategy of firms. The role of innovation processes is critical in carrying out innovation strategies in practice, supporting the development of organizational routines for innovation, and driving the strategic renewal of companies. The primary focus of the thesis from systems perspective is on idea management systems, which are defined as a part of innovation management systems, and defined for this thesis as any working combination of methodology and tools (manual or IT-supported) that enhance the management of innovations within their early phases. The main contribution of the thesis are the managerial frameworks developed for managing the front end of innovation, which purposefully “wire” the front end of innovation into the strategy and business processes of a firm. The thesis contributes to modern innovation management by connecting the internal and external collaboration networks as foundational elements for successful management of the early phases of innovation processes in a dynamic environment. The innovation capability of a firm is largely defined by its ability to rely on and make use of internal and external collaboration already during the front end activities, which by definition include opportunity identification and analysis, idea generation, profileration and selection, and concept definition. More specifically, coordination of the interfaces between these activities, and between the internal and external innovation environments of a firm is emphasised. The role of information systems, in particular idea management systems, is to support and delineate the innovation-oriented behaviour and interaction of individuals and organizations during front end activities. The findings and frameworks developed in the thesis can be used by companies for purposeful promotion of their front end processes. The thesis provides a systemic strategy framework for managing the front end of innovation – not as a separate process, but as an elemental bundle ofactivities that is closely linked to the overall innovation process and strategy of a firm in a distributed environment. The theoretical contribution of the thesis relies on the advancement of the open innovation paradigm in the strategic context of a firm within its internal and external innovation environments. This thesis applies the constructive research approach and case study methodology to provide theoretically significant results, which are also practically beneficial.

Performance Improvement of Centrifugal Compressor Stage with Pinched Geometry or Vaned Diffuser

Centrifugal compressors are widely used for example in refrigeration processes, the oil and gas industry, superchargers, and waste water treatment. In this work, five different vaneless diffusers and six different vaned diffusers are investigated numerically. The vaneless diffusers vary only by their diffuser width, so that four of the geometries have pinch implemented to them. Pinch means a decrease in the diffuser width. Four of the vaned diffusers have the same vane turning angle and a different number of vanes, and two have different vane turning angles. The flow solver used to solve the flow fields is Finflo, which is a Navier-Stokes solver. All the cases are modeled with the Chien's k – έ- turbulence model, and selected cases are modeled also with the k – ώ-SST turbulence model. All five vaneless diffusers and three vaned diffusers are investigated also experimentally. For each construction, the compressor operating map is measured according to relevant standards. In addition to this, the flow fields before and after the diffuser are measured with static and total pressure, flow angle and total temperature measurements. When comparing the computational results to the measured results, it is evident that the k – ώ-SST turbulence model predicts the flow fields better. The simulation results indicate that it is possible to improve the efficiency with the pinch, and according to the numerical results, the two best geometries are the ones with most pinch at the shroud. These geometries have approximately 4 percentage points higher efficiency than the unpinched vaneless diffusers. The hub pinch does not seem to have any major benefits. In general, the pinches make the flow fields before and after the diffuser more uniform. The pinch also seems to improve the impeller efficiency. This is down to two reasons. The major reason is that the pinch decreases the size of slow flow and possible backflow region located near the shroud after the impeller. Secondly, the pinches decrease the flow velocity in the tip clearance, leading to a smaller tip leakage flow and therefore slightly better impeller efficiency. Also some of the vaned diffusers improve the efficiency, the increment being 1...3 percentage points, when compared to the vaneless unpinched geometry. The measurement results confirm that the pinch is beneficial to the performance of the compressor. The flow fields are more uniform with the pinched cases, and the slow flow regions are smaller. The peak efficiency is approximately 2 percentage points and the design point efficiency approximately 4 percentage points higher with the pinched geometries than with the un- pinched geometry. According to the measurements, the two best geometries are the ones with the most pinch at the shroud, the case with the pinch only at the shroud being slightly better of the two. The vaned diffusers also have better efficiency than the vaneless unpinched geometries. However, the pinched cases have even better efficiencies. The vaned diffusers narrow the operating range considerably, whilst the pinch has no significant effect on the operating range.

Environmental policy instruments concerning industrial end-use energy efficiency

Energy efficiency and saving energy are the main question marks when thinking of reducing carbon dioxide emissions or cutting costs. The objective of thesis is to evaluate policy instruments concerning end-use energy efficiency of heavy industry in European Union. These policy instruments may be divided in various ways, but in this thesis the division is to administrative, financial, informative and voluntary instruments. Administrative instruments introduced in this thesis are Directive on Integrated Pollution Prevention and Control, Directive on Energy End-use Efficiency and Energy Services, and Climate and Energy Package. Financial means include energy and emission taxation, EU Emission Trading Scheme and diverse support systems. Informative instruments consist of horizontal BAT Reference Document for Energy Efficiency, as well as substantial EU documents including Green Paper on Energy Efficiency, Action Plan for Energy Efficiency and An Energy Policy for Europe. And finally, voluntary instruments include environmental managements systems like ISO 14001 and EMAS, energy auditing and benchmarking. The efficiency of different policy instruments vary quite a lot. Informative instruments lack the commitment from industry and are thus almost ineffective, contrary to EU Emission Trading Scheme, which is said to be the solution to climate problems. The efficiency of administrative means can be placed between those mentioned and voluntary instruments are still quite fresh to be examined fruitfully. However, each instrument has their potential and challenges. Cases from corporate world strengthen the results from theoretical part. Cases were written mainly on the basis of interviews. The interviewees praised the energy efficiency contract of Finnish industry, but the EU ETS takes the leading role of policy instruments. However, for industry the reductions do not come easily.

Challenges and Means for the Front End Activities of Software Development

The front end of innovation is regarded as one of the most important steps in building new software products or services, and the most significant benefits in software development can be achieved through improvements in the front end activities. Problems in the front end phase have an impact on customer dissatisfaction with delivered software, and on the effectiveness of the entire software development process. When these processes are improved, the likelihood of delivering high quality software and business success increases. This thesis highlights the challenges and problems related to the early phases of software development, and provides new methods and tools for improving performance in the front end activities of software development. The theoretical framework of this study comprises two fields of research. The first section belongs to the field of innovation management, and especially to the management of the early phases of the innovation process, i.e. the front end of innovation. The second section of the framework is closely linked to the processes of software engineering, especially to the early phases of the software development process, i.e. the practice of requirements engineering. Thus, this study extends the theoretical knowledge and discloses the differences and similarities in these two fields of research. In addition, this study opens up a new strand for academic discussion by connecting these research directions. Several qualitative business research methodologies have been utilized in the individual publications to solve the research questions. The theoretical and managerial contribution of the study can be divided into three areas: 1) processes and concepts, 2) challenges and development needs, and 3) means and methods for the front end activities of software development. First, the study discloses the difference and similarities between the concepts of the front end of innovation and requirements engineering, and proposes a new framework for managing the front end of the software innovation process, bringing business and innovation perspectives into software development. Furthermore, the study discloses managerial perceptions of the similarities and differences in the concept of the front end of innovation between the software industry and the traditional industrial sector. Second, the study highlights the challenges and development needs in the front end phase of software development, especially challenges in communication, such as linguistic problems, ineffective communication channels, a communication gap between users/customers and software developers, and participation of multiple persons in software development. Third, the study proposes new group methods for improving the front end activities of software development, especially customer need assessment, and the elicitation of software requirements.

Effect of hydrodynamics on modelling, monitoring and control of crystallization

Crystallization is a purification method used to obtain crystalline product of a certain crystal size. It is one of the oldest industrial unit processes and commonly used in modern industry due to its good purification capability from rather impure solutions with reasonably low energy consumption. However, the process is extremely challenging to model and control because it involves inhomogeneous mixing and many simultaneous phenomena such as nucleation, crystal growth and agglomeration. All these phenomena are dependent on supersaturation, i.e. the difference between actual liquid phase concentration and solubility. Homogeneous mass and heat transfer in the crystallizer would greatly simplify modelling and control of crystallization processes, such conditions are, however, not the reality, especially in industrial scale processes. Consequently, the hydrodynamics of crystallizers, i.e. the combination of mixing, feed and product removal flows, and recycling of the suspension, needs to be thoroughly investigated. Understanding of hydrodynamics is important in crystallization, especially inlargerscale equipment where uniform flow conditions are difficult to attain. It is also important to understand different size scales of mixing; micro-, meso- and macromixing. Fast processes, like nucleation and chemical reactions, are typically highly dependent on micro- and mesomixing but macromixing, which equalizes the concentrations of all the species within the entire crystallizer, cannot be disregarded. This study investigates the influence of hydrodynamics on crystallization processes. Modelling of crystallizers with the mixed suspension mixed product removal (MSMPR) theory (ideal mixing), computational fluid dynamics (CFD), and a compartmental multiblock model is compared. The importance of proper verification of CFD and multiblock models is demonstrated. In addition, the influence of different hydrodynamic conditions on reactive crystallization process control is studied. Finally, the effect of extreme local supersaturation is studied using power ultrasound to initiate nucleation. The present work shows that mixing and chemical feeding conditions clearly affect induction time and cluster formation, nucleation, growth kinetics, and agglomeration. Consequently, the properties of crystalline end products, e.g. crystal size and crystal habit, can be influenced by management of mixing and feeding conditions. Impurities may have varying impacts on crystallization processes. As an example, manganese ions were shown to replace magnesium ions in the crystal lattice of magnesium sulphate heptahydrate, increasing the crystal growth rate significantly, whereas sodium ions showed no interaction at all. Modelling of continuous crystallization based on MSMPR theory showed that the model is feasible in a small laboratoryscale crystallizer, whereas in larger pilot- and industrial-scale crystallizers hydrodynamic effects should be taken into account. For that reason, CFD and multiblock modelling are shown to be effective tools for modelling crystallization with inhomogeneous mixing. The present work shows also that selection of the measurement point, or points in the case of multiprobe systems, is crucial when process analytical technology (PAT) is used to control larger scale crystallization. The thesis concludes by describing how control of local supersaturation by highly localized ultrasound was successfully applied to induce nucleation and to control polymorphism in reactive crystallization of L-glutamic acid.

Knowledge Sharing between Generations in an Organisation - Retention of the Old or Building the New?

The study explores knowledge transfer between retiring employees and their successors in expert work. My aim is to ascertain whether there is knowledge development or building new knowledge related to this organisational knowledge transfer between generations; in other words, is the transfer of knowledge from experienced, retiring employees to their successors merely retention of the existing organisational knowledge by distributing it from one individual to another or does this transfer lead to building new and meaningful organisational knowledge. I call knowledge transfer between generations and the possibly related knowledge building in this study knowledge sharing between generations. The study examines the organisation and knowledge management from a knowledge-based and constructionist view. From this standpoint, I see knowledge transfer as an interactive process, and the exploration is based on how the people involved in this process understand and experience the phenomenon studied. The research method is organisational ethnography. I conducted the analysis of data using thematic analysis and the articulation method, which has not been used before in organisational knowledge studies. The primary empirical data consists of theme interviews with twelve employees involved in knowledge transfer in the organisation being studied and five follow-up theme interviews. Six of the interviewees are expert duty employees due to retire shortly, and six are their successors. All those participating in the follow-up interviews are successors of those soon to retire from their expert responsibilities. The organisation in the study is a medium-sized Finnish firm, which designs and manufactures electrical equipment and systems for the global market. The results of the study show that expert work-related knowledge transfer between generations can mean knowledge building which produces new, meaningful knowledge for the organisation. This knowledge is distributed in the organisation to all those that find it useful in increasing the efficiency and competitiveness of the whole organisation. The transfer and building of knowledge together create an act of knowledge sharing between generations where the building of knowledge presupposes transfer. Knowledge sharing proceeds between the expert and the novice through eight phases. During the phases of knowledge transfer the expert guides the novice to absorb the knowledge to be transferred. With the expert’s help the novice gradually comes to understand the knowledge and in the end he or she is capable of using it in his or her work. During the phases of knowledge building the expert helps the novice to further develop the knowledge being transferred so that it becomes new, useful knowledge for the organisation. After that the novice takes the built knowledge to use in his or her work. Based on the results of the study, knowledge sharing between generations takes place in interaction and ends when knowledge is taken to use. The results I obtained in the interviews by the articulation method show that knowledge sharing between generations is shaped by the novices’ conceptions of their own work goals, knowledge needs and duties. These are not only based on the official definition of the work, but also how the novices find their work or how they prioritise the given objectives and responsibilities. The study shows that the novices see their work primarily as maintenance or development. Those primarily involved in maintenance duties do not necessarily need knowledge defined as transferred between generations. Therefore, they do not necessarily transfer knowledge with their assigned experts, even though this can happen in favourable circumstances. They do not build knowledge because their view of their work goals and duties does not require the building of new knowledge. Those primarily involved in development duties, however, do need knowledge available from their assigned experts. Therefore, regardless of circumstances they transfer knowledge with their assigned experts and also build knowledge because their work goals and duties create a basis for building new knowledge. The literature on knowledge transfer between generations has focused on describing either the knowledge being transferred or the means by which it is transferred. Based on the results of this study, however, knowledge sharing between generations, that is, transfer and building is determined by how the novice considers his or her own knowledge needs and work practices. This is why studies on knowledge sharing between generations and its implementation should be based not only on the knowledge content and how it is shared, but also on the context of the work in which the novice interprets and shares knowledge. The existing literature has not considered the possibility that knowledge transfer between generations may mean building knowledge. The results of this study, however, show that this is possible. In knowledge building, the expert’s existing organisational knowledge is combined with the new knowledge that the novice brings to the organisation. In their interaction this combination of the expert’s “old” and the novice’s “new” knowledge becomes new, meaningful organisational knowledge. Previous studies show that knowledge development between the members of an organisation is the prerequisite for organisational renewal which in turn is essential for improved competitiveness. Against this background, knowledge building enables organisational renewal and thus enhances competitiveness. Hence, when knowledge transfer between generations is followed by knowledge building, the organisation kills two birds with one stone. In knowledge transfer the organisation retains the existing knowledge and thus maintains its competitiveness. In knowledge building the organisation developsnew knowledge and thus improves its competitiveness.

Immunohistochemical evaluation for P53 and VEGF (Vascular Endothelial Growth Factor) is not prognostic for long term survival in end stage esophageal adenocarcinoma

OBJECTIVES: To correlate the expression of p53 protein and VEGF with the prognosis of patients submitted to curative resection to treat esophageal adenocarcinoma. METHODS: Forty-six patients with esophageal adenocarcinoma, submitted to curative resection, were studied. The expressions of p53 protein and VEGF were assessed by immunohistochemistry in 52.2% and 47.8% of tumors, respectively. RESULTS: P53 protein and VEGF expressions coincided in 26% of the cases, and no correlation between these expressions was observed. None of the clinicopathological factors showed a significant correlation with p53 protein or VEGF expressions. There was no significant association between p53 protein and VEGF expressions and long-term survival. CONCLUSION: The expression of p53 protein and VEGF did not correlate with prognosis in esophageal adenocarcinoma patients submitted to curative resection.

Evaluation of left ventricular diastolic echocardiographic parameters in healthy dogs by pulsed-wave Doppler

Left ventricular diastolic dysfunction plays an important role on heart failure progression. In order to obtain additional reference values of left ventricular diastolic parameters and investigate influence of common variables, peak E wave (peak E), peak A wave (peak A), E/A ratio (E/A), E wave deceleration time (EDT) and isovolumic relaxation time (IRVT) were studied in 40 clinically healthy dogs, by pulsed wave Doppler. The following values were obtained: peak E = 0.747 ± 0.117 m/s, peak A = 0.487 ± 0.062 m/s, E/A = 1.533 ± 0.198, EDT = 88.7 ± 9.2 ms and IRVT = 0.080 ± 0.009 s. Some parameters were influenced by heart rate (peak E, peak A and IRVT), by age (peak A and E/A) and by body weight (TRIV). Gender influence was absent. Values obtained can be used as reference for canine specimens but its interpretation should consider on the influence of related variables.