Decay of imprinted surface waves in polymers

CONCLUSIONS The focus of this work was the investigation ofanomalies in Tg and dynamics at polymer surfaces. Thethermally induced decay of hot-embossed polymer gratings isstudied using laser-diffraction and atomic force microscopy(AFM). Monodisperse PMMA and PS are selected in the Mwranges of 4.2 to 65.0 kg/mol and 3.47 to 65.0 kg/mol,respectively. Two different modes of measurement were used:the one mode uses temperature ramps to obtain an estimate ofthe near-surface glass temperature, Tdec,0; the other modeinvestigates the dynamics at a constant temperature aboveTg. The temperature-ramp experiments reveal Tdec,0 valuesvery close to the Tg,bulk values, as determined bydifferential scanning calorimetry (DSC). The PMMA of65.0 kg/mol shows a decreased value of Tg, while the PS samples of 3.47 and 10.3 kg/mol (Mw

Magnetic properties of selected 3d- and 4f-systems on alpha-Al 2 O 3 substrates

In this work the growth and the magnetic properties of the transition metals molybdenum, niobium, and iron and of the highly-magnetostrictive C15 Laves phases of the RFe2 compounds (R: Rare earth metals: here Tb, Dy, and Tb{0.3}Dy{0.7} deposited on alpha-Al2O3 (sapphire) substrates are analyzed. Next to (11-20) (a-plane) oriented sapphire substrates mainly (10-10) (m-plane) oriented substrates were used. These show a pronounced facetting after high temperature annealing in air. Atomic force microscopy (AFM) measurements reveal a dependence of the height, width, and angle of the facets with the annealing temperature. The observed deviations of the facet angles with respect to the theoretical values of the sapphire (10-1-2) and (10-11) surfaces are explained by cross section high resolution transmission electron microscopy (HR-TEM) measurements. These show the plain formation of the (10-11) surface while the second, energy reduced (10-1-2) facet has a curved shape given by atomic steps of (10-1-2) layers and is formed completely solely at the facet ridges and valleys. Thin films of Mo and Nb, respectively, deposited by means of molecular beam epitaxy (MBE) reveal a non-twinned, (211)-oriented epitaxial growth as well on non-faceted as on faceted sapphire m-plane, as was shown by X-Ray and TEM evaluations. In the case of faceted sapphire the two bcc crystals overgrow the facets homogeneously. Here, the bcc (111) surface is nearly parallel to the sapphire (10-11) facet and the Mo/Nb (100) surface is nearly parallel to the sapphire (10-1-2) surface. (211)-oriented Nb templates on sapphire m-plane can be used for the non-twinned, (211)-oriented growth of RFe2 films by means of MBE. Again, the quality of the RFe2 films grown on faceted sapphire is almost equal to films on the non-faceted substrate. For comparison thin RFe2 films of the established (110) and (111) orientation were prepared. Magnetic and magnetoelastic measurements performed in a self designed setup reveal a high quality of the samples. No difference between samples with undulated and flat morphology can be observed. In addition to the preparation of covering, undulating thin films on faceted sapphire m-plane nanoscopic structures of Nb and Fe were prepared by shallow incidence MBE. The formation of the nanostructures can be explained by a shadowing of the atomic beam due to the facets in addition to de-wetting effects of the metals on the heated sapphire surface. Accordingly, the nanostructures form at the facet ridges and overgrow them. The morphology of the structures can be varied by deposition conditions as was shown for Fe. The shape of the structures vary from pearl-necklet strung spherical nanodots with a diameter of a few 10 nm to oval nanodots of a few 100 nm length to continuous nanowires. Magnetization measurements reveal uniaxial magnetic anisotropy with the easy axis of magnetization parallel to the facet ridges. The shape of the hysteresis is depending on the morphology of the structures. The magnetization reversal processes of the spherical and oval nanodots were simulated by micromagnetic modelling and can be explained by the formation of magnetic vortices.

Nanostructuring by templated synthesis of nanowires and controlled crystallization of calcium phosphate on self-assembled monolayers

The idea was to obtain nanowires in a chemical laboratory under convenient and simple conditions by employing templates. Thus it was possible to produce nanochains by interlinking of gold colloids synthesized by the two-phase-method of M. Brust with by making use of vanadiumoxide nanotubes as template. The length of the resulting nanowires is varying between 1100 nm and 200 nm with a diameter of about 16 nm. Due to a flexible linker the obtained nanowires are not completely rigid. These unique structural features could make them interesting objects for structuring and assembling in the nanoscale range. Another way to produce gold nanowires was realized by a two-step surface metallization procedure, using type I collagen fibres as a template. Gold colloids were used to label the collagen fibres by direct electrostatic interaction, followed by growth steps to enhance the size of the adsorbed colloidal gold crystals, resulting in a complete metallization of the template surface. The length of the resulting gold nanowires reaches several micrometers, with a diameter ~ 100 to 120 nm. To gain a deeper insight into the process of biomineralization the cooperative effect of self-assembled monolayers as substrate and a soluble counterpart on the nucleation and crystal growth of calcium phosphate was studied by diffusion techniques with a pH switch as initiator. As soluble component Perlucin and Nacrein were used. Both are proteins originally extracted from marine organisms, the first one from the Abalone shell and the second one from oyster pearls. Both are supposed to facilitate the calcium carbonate formation in vivo. Studies with Perlucin revealed that this protein shows a clear cooperative effect at a very low concentration with a hydrophobic surface promoting the calcium phosphate precipitation resulting in a sponge like structure of hydroxyapatite. The Perlucin molecule is very flexible and is unfolded by adsorbing to the hydrophobic surface and uncovers its active side. Hydrophilic surfaces did not have a deeper impact. Studies with Nacrein as additive have shown that the protein stabilizes octacalcium phosphate at room temperature on carboxylic self-assembled monolayer and at 34 °C on all other employed surfaces by interaction with the mineral. On the hydroxyl-, alkyl-, and amin-terminated self-assembled monolayers at room temperature the octacalcium phosphate get transformed to hydroxyapatite. Main analytical techniques which are used in this work are transmission electron microscopy, high resolution scanning electron microscopy, surface plasmon resonance spectroscopy, atomic force microscopy, Raman micro-spectroscopy and quartz crystal microbalance.

Grating coupled surface plasmon enhanced fluorescence spectroscopy

Over the last three decades, sensors based on the phenomenon of surface plasmon resonance have proven particularly suitable for real time thin film characterization, gas detection, biomolecular interaction examination and to supplement electrochemical methods. Systems based on prism coupling have been combined with fluorescence detection under the name of surface plasmon fluorescence spectroscopy to increase sensitivity even further. Alternatively, metal gratings can be employed to match photons for plasmon resonance. The real time monitoring of binding reactions not yet been reported in the combination of fluorescence detection and grating coupling. Grating-based systems promise more competitive products, because of reduced operating costs, and offer benefits for device engineering. This thesis is comprised of a comprehensive study of the suitability of grating coupling for fluorescence based analyte detection. Fundamental properties of grating coupled surface plasmon fluorescence spectroscopy are described, as well as issues related to the commercial realization of the method. Several new experimental techniques are introduced and demonstrated in order to optimize performance in certain areas and improve upon capabilities in respect to prism-based systems. Holographically fabricated gratings are characterized by atomic force microscopy and optical methods, aided by simulations and profile parameters responsible for efficient coupling are analyzed. The directional emission of fluorophores immobilized on a grating surface is studied in detail, including the magnitude and geometry of the fluorescence emission pattern for different grating constants and polarizations. Additionally, the separation between the minimum of the reflected intensity and the maximum fluorescence excitation position is examined. One of the key requirements for the commercial feasibility of grating coupling is the cheap and faithful mass production of disposable samples from a given master grating. The replication of gratings is demonstrated by a simple hot embossing method with good reproducibility to address this matter. The in-situ fluorescence detection of analyte immobilization and affinity measurements using grating coupling are described for the first time. The physical factors related to the sensitivity of the technique are assessed and the lower limit of detection of the technique is determined for an exemplary assay. Particular attention is paid to the contribution of bulk fluorophores to the total signal in terms of magnitude and polarization of incident and emitted light. Emission from the bulk can be a limiting factor for experiments with certain assay formats. For that reason, a novel optical method, based on the modulation of both polarization and intensity of the incident beam, is introduced and demonstrated to be capable of eliminating this contribution.

Grenzflächenverhalten und Strukturierung von dünnen, amphiphilen Blockcopolymerfilmen

Die Oberfläche von Blockcopolymerfilmen wird aus denjenigen Blöcken gebildet, die gegenüber dem benachbarten Medium die geringste Oberflächenenergie besitzen. Durch eine gezielte Änderung des Mediums kann man Einfluss auf die chemische Zusammensetzung nehmen und einen Wechsel der Oberflächenlamelle erzwingen. Das Ziel dieser Arbeit war es, das Grenzflächenverhalten von dünnen, amphiphilen Blockcopolymerfilmen näher zu untersuchen, die Filmoberflächen in einem lösungsmittelfreien Prozess lateral zu strukturieren und anschließend chemisch zu modifizieren. Zu diesem Zweck wurden zunächst neuartige hydrophile und hydrophobe Styrenderivate mit kurzen Seitenketten dargestellt, die anschließend durch kontrollierte radikalische Polymerisation („stable free radical polymerisation“ SFRP) mit dem TEMPO Unimer zu amphiphilen Diblockcopolymeren polymerisiert wurden. Funktionelle Gruppen in den hydrophilen Blöcken sollen zusätzlich eine chemische Modifizierung der Oberflächen dünner Blockcopolymerfilme ermöglichen. Der Nachweis der Reorientierung der Oberflächenlamelle unter dem Einfluss angrenzender polarer und unpolarer Medien gelang im Folgenden sowohl indirekt durch Kontaktwinkelmessungen, als auch direkt durch „Near edge X-ray Absorption Fine Structure“ Spektroskopie (NEXAFS). Durch Letztere konnten auch kinetische Informationen über den Prozess der Reorientierung gewonnen werden. In AFM Studien konnten weiterhin Zwischenstufen des von Senchu et al. postulierten Mechanismus nachgewiesen werden, der die Reorientierung als eine Art Reißverschlussmechanismus beschreibt, bei dem sich die energetisch günstigere Lamelle über die ungünstigere Oberflächenlamelle stülpt. Die laterale Strukturierung der Oberflächen dünner Blockcopolymerfilme erfolgte abweichend von der bekannten Technik, die auf der Verwendung von hydrophoben PDMS Stempeln und einem polaren Lösungsmittel zurückgreift, durch einen lösungsmittelfreien Prozess mit hydrophilen PDMS Stempeln. Auf die hydrophilen Bereiche der so strukturierten Blockcopolymeroberflächen konnte dann mittels einer Templatstrategie selektiv elementares Kupfer abgeschieden werden. Durch die Erzeugung leitfähiger Strukturen auf Blockcopolymerfilmen konnte exemplarisch die Eignung dieser zum Aufbau von Sensorstrukturen gezeigt werden.

Mechanische Eigenschaften von freitragenden artifiziellen und nativen Membranen

This thesis presents a new method to explore the local mechanical properties such as bending modulus or surface tension of artificial and native pore-spanning membranes. Therefore the elastic response of a free-standing membrane to a local indentation by the means of atomic force microscopy is measured. Starting point are highly hexagonal ordered pores in alumina produced by electrochemical anodization of planar aluminium. The homogeneous pore radius can by tailored in the range of 10 nm up to 200 nm, but radius of 33 nm, 90 nm and 200 nm turned out to be best suited for investigation of the mechanical properties of pore-spanning native or artificial membranes. In this work artificial membrane systems consisting of DODAB as a bilayer in gel phase or DOTAP as a fluide membrane are spreaded by vesicle absorption on hexagonal structured pores after chemisorption of a 3-mercaptopropionic acid monolayer. Centrally indenting these nanodrums with an atomic force microscope tip yields force-indentation curves, which are quantitatively analyzed by solving the corresponding shape equations of continuum curvature elasticity. Since the measured response depends in a known way on the system geometry (pore size, tip radius) and on material parameters (bending modulus, lateral tension, adhesion), this opens the possibility to monitor local elastic properties of lipid membranes in a well-controlled setting. Additionally the locally distributed mechanical properties of pore-spanning artificial membranes are compared to those of native pore-spanning membranes. Therefore the basal membrane of MDCK II cells was prepared on porous alumina assays and their mechanical properties were analyzed by means of atomic force microscopy. Finally the elastic behavior such as the Young modulus of living MDCK II cells under various osmotic pressures is investigated. By changing the osmolarity in the extracellular region of MDCK II cells a volume change is induced according to hydration and dehydration of the cells, respectively. This volume change induces also a change in the elastic behavior of the cell, which is quantified by the means of force spectroscopy.

Advanced SPM studies on the growth of ultrathin films of organic semiconductors at metal and dielectric interfaces

Many studies on the morphology, molecular orientation, device performance, substrate nature and growth parameter dependence have been carried out since the proposal of Sexithiophene (6T) for organic electronics [ ] However, these studies were mostly performed on films thicker than 20nm and without specifically addressing the relationship between morphology and molecular orientation within the nano and micro structures of ultrathin films of 0-3 monolayers. In 2004, the observation that in OFETs only the first few monolayers at the interface in contact with the gate insulator contribute to the charge transport [ ], underlined the importance to study submonolayer films and their evolution up to a few monolayers of thickness with appropriate experimental techniques. We present here a detailed Non-contact Atomic Force Microscopy and Scanning Tunneling Microscopy study on various substrates aiming at the investigation of growth mechanisms. Most reported similar studies are performed on ideal metals in UHV. However it is important to investigate the details of organic film growth on less ideal and even technological surfaces and device testpatterns. The present work addresses the growth of ultra thin organic films in-situ and quasi real-time by NC-AFM. An organic effusion cell is installed to evaporate the organic material directly onto the SPM sample scanning stage.

Functionalized surfaces and surface functionalization of nanomaterials

Nature leads, we follow. But nanotechnologists are in hot pursuit, in designing controllable structures that can mimic naturally occurring and artificially synthesized materials on a common platform. The supramolecular chemistry concerns the investigation of nature principles to produce fascinating complexed and functional molecular assemblies, as well as the utilization of these principles to generate novel devices and materials, potentially useful for sensing, catalysis, transport and other applications in medical or engineering science. The work presented in this thesis is a compilation of different synthetic methods to achieve inorganic-organic hybrid nanomaterials. Silicatein, a protein enzyme, which acts both as a catalyst and template for the formation of silica needles in marine sponges, has been used for the biosynthesis of semiconductor metal oxides on surfaces. Silicatein was immobilized on gold (111) surfaces using alkane thiol, as well as on a novel self-assembly of NTA on top of a “cushion” of reactive ester polymer has been successfully employed to make functionalised surfaces. The immobilization of silicatein on surfaces was monitored by surface plasmon spectroscopy, atomic force microscopy and confocal laser scanning microscopy. Surface bound silicatein retains its biocatalytic activity, which was demonstrated by monitoring its hydrocatalytic activity to catalyse the synthesis of biosilica, biotitania, and biozirconia. The synthesis of semiconductor metal oxides was characterized using scanning electron microscopy. This hydrolytic biocatalyst is used to synthesize the gold nanoparticles. The gold nanoparticles are formed by reduction of tetrachloroaurate, AuCl4-, by the action of sulfhydryl groups hidden below the surface groups of the protein. The resulting gold nanoparticles which are stabilized by surface bound silicatein further aggregate to form Au nanocrystals. The shape of the nanocrystals obtained by using recombinant silicatein is controlled through chiral induction by the protein during the nucleation of the nanocrystals. As an extension of this work, TiO2 nanowires were functionalized using polymeric ligand which incorporates the nitrilotriacetic acid (NTA) linker in the back bone to immobilize His-tagged silicatein onto the TiO2 nanowires. The surface bound protein not only retains its original hydrolytic properties, but also acts as a reductant for AuCl4- in the synthesis of hybrid TiO2/silicatein/Au nanocomposites. Functionalized, monocrystalline rutile TiO2 nanorods were prepared from TiCl4 in aqueous solution in the presence of dopamine. The surface bound organic ligand controls the morphology as well as the crystallinity and the phase selection of TiO2. The surface amine groups can be tailored further with functional molecules such as dyes. As an example, this surface functionality is used for the covalent binding of a fluorescent dye,4-chloro-7- nitrobenzylurazene (NBD) to the TiO2 nanorods. The polymeric ligands have been used successfully for the in-situ and post-functionalization of TiO2 nanoparticles. Besides to chelating dopamine anchor group the multifunctional ligand system presented here incorporates a modifier molecule which allows the binding of functional molecules (here the dyes pyrene, NBD, and Texas Red) as well as additional entities which allow tailoring the solubility of inorganic nanocrystals in different solvents. A novel method for the surface functionalization of fullerene-type MoS2 nanoparticles and subsequently binding these nanoparticles onto TiO2 nanowires has been reported using polymeric ligands. The procedure involves the complexation of IF-MoS2 with a combination of Ni2+ via an umbrella-type nitrilotriacetic acid (NTA) and anchoring them to the sidewalls of TiO2 nanowires utilizing the hydroxyl groups of dopamine present in the main contents of polymeric ligand. A convenient method for the synthesis of Au/CdS nanocomposites has been presented, which were achieved through the novel method of thiol functionalization of gold colloids. The thermodynamically most stable phase of ZrO2 (cubic) has been obtained at much lower temperature (180°C). These nanoparticles are highly blue fluorescent, with a high surface area.

Extended arm polyphenylene dendrimers

In order to eliminate the de Gennes packing problem, which usually limits the attainable size of dendrimers, a new branching unit containing para-tetraphenylene ethynyl arms has been synthesized and utilized in the preparation of dendrimers of the Müllen type. The divergent principle of synthesis, based on the Dilthey reaction, could be carried up to sixth generation which contains 2776 benzene rings and possesses a diameter in the 27 nm range ("exploded dendrimer"). Monodispersity and dimensions of this and the lower generation species have been studied by MALDI-TOF MS (including the very recent superconducting tunnel junction detector), by size-exclusion chromatography, dynamic light scattering, transmission electron microscopy, and atomic force microscopy. Interesting features, apart from the huge dimension, are the low density and high porosity of these giant molecules which cause extensive aggregation in the gas phase, flattening on solid support (AFM) and the ready incorporation of guest molecules in the condensed phase. Since the synthesis of the para-tetraphenylene arms is quite elaborate, similar dendrimers containing para-terphenylene arms have been prepared; they are accessible more economically ("semi-exploded dendrimers"). It has been shown that they in several aspects mimic the features of the "exploded dendrimers". In order to take advantage of the presence of large internal cavities in this dendrimer type, dendrons containing -C≡C- triple bonds have also been incorporated. Surprisingly, they are readily hydrogenated under the condition of heterogeneous catalysis (Pd/C) which demonstrates the large size of the cavities. As revealed by a quartz microbalance study the post-hydrogenation dendrimers are less prone to incorporate guest molecules than before hydrogenation. Obviously, the more flexible nature of the former reduces porosity, it also leads to significant shrinkage. An interesting perspective is the use of homogeneous hydrogenation catalysts of variable size with the aim of determining the dimension of internal free space.

Deposizione elettrochimica di film polimerici foto-attivi per la realizzazione di celle solari

Plastic solar cells bear the potential for large-scale power generation based on flexible, lightweight, inexpensive materials. Since the discovery of the photo-induced electron transfer from a conjugated polymer (electron-donor) to fullerene or its derivatives molecules (electron-acceptors), followed by the introduction of the bulk heterojunction concept which means donors and acceptors blended together to realize the fotoactive layer, materials and deposition techniques have been extensively studied. In this work, electrochemical-deposition methods of polymeric conductive films were studied in order to realize bulk heterojunction solar cells. Indium Tin Oxide (ITO) glass electrodes modified with a thin layer of poly(3,4-ethylenedioxythiophene) (PEDOT) were electrochemically prepared under potentiodynamic and potentiostatic conditions; then those techniques were applied for the electrochemical co-deposition of donor and acceptor on modified ITO electrode to produce the active layer (blend). For the deposition of the electron-donor polymer the electropolymerization of many functionalized thiophene monomers was investigated while, as regards acceptors, fullerene was used first, then the study was focused on its derivative PCBM ([6,6]-phenyl-C61-butyric acid methyl ester). The polymeric films obtained (PEDOT and blend) were electrochemically and spectrophotometrically characterized and the film thicknesses were evaluated by atomic force microscopy (AFM). Finally, to check the performances and the efficiency of the realized solar cells, tests were carried out under standard conditions. Nowadays bulk heterojunction solar cells are still poorly efficient to be competitively commercialized. A challenge will be to find new materials and better deposition techniques in order to obtain better performances. The research has led to several breakthroughs in efficiency, with a power conversion efficiency approaching 5 %. The efficiency of the solar cells produced in this work is even lower (lower than 1 %). Despite all, solar cells of this type are interesting and may represent a cheaper and easier alternative to traditional silicon-based solar panels.

Surface layer formation in polymer melts and in solutions

In this work the surface layer formation in polymer melts and in polymer solutions have been investigated with the atomic force microscope (AFM). In polymer melts, the formation of an immobile surface layer results in a steric repulsion, which can be measured by the AFM. From former work it is know, that polydimethyl siloxane (PDMS) forms a stable surface layer for molecular weights above 12 kDa. In the present thesis, polyisoprene (PI) was investigated apart from PDMS, by a)measuring the steric surface interactions and b)measuring the surface slip in hydrodynamic experiments. If a polymer flows over a surface, the flow velocity at the surface is larger then zero. If case of a surface layer formation the flow plane changes to the top of the adsorbed layer and the surface slip is reduced to zero. By measuring the surface slip in hydrodynamic experiments, it is therefore possible to determine the presence of a stable surface layer. The results show no stable repulsion for PI and only a small decrease of the surface slip. This indicates that PI does not form a stable surface layer, but is only adsorbed weakly to the surface. Furthermore for 8 kDa PDMS the timescale of the formation of a surface layer was investigated by changing themaximal force the tip applied to the surface. With a repulsive force present, applying a higher force than 15 nN resulted in a destruction of the surface layer, indicated by attractive forces. Reducing the applied force below 15 nN then resulted in an increase of the repulsion to the former state during one minute, thus indicating that a surface layer can be formed within one minute even under the influence of continuous measurements. As a next step, mixtures of two PDMS homopolymers with different chain lengths have been investigated. The aim was to verify theoretical predictions that shorter chains should predominate at the surface due to their smaller loss in conformational entropy. The measurements where done in dependence of the volume fractions of short and long chain PMDS. The results confirmed the short chain dominance for all mixtures with less then 90 vol.% long chain PDMS. Surface layer formation in solution was investigated for superplasticizers which are industrially used as an additive to cement. They change the surface interaction between the cement grains from attractive to repulsive and the freshlymixed cement paste therefore becomes liquid. The aimin this part of the thesis was, to investigate cement particle interactions in a close to real environment. Therefore calcium silicate hydrate phases have been precipitated onto an AFM tip and onto a calcite crystal and the interaction between these surfaces have beenmeasured with and without addition of superplasticizers. The measurements confirmed the change from attraction to repulsion upon addition of superplasticizers. The repulsive steric interaction increased with the length of the sidechain of the superplasticizer, and the dependence of the range of the steric interactions on the sidechain length indicated that the sidechains are in a coiled conformation.

Ion channels in mixed tethered bilayer lipid membranes

Mixed tethered bilayer lipid membranes (tBLMs) are described based on the self-assembly of a monolayer on template stripped gold, of an archea analogue thiolipid, 2,3-di-o-phytanyl-sn-glycerol-1-tetraethylene glycol-D,L--lipoic acid ester lipid (DPTL), and a newly designed dilution molecule, tetraethylene glycol-D,L--lipoic acid ester (TEGL). The usage of spacer and addition of extra dilution molecules between the substrate and the bilayer is that this architecture provides an ionic reservoir underneath the membrane, avoiding direct contact of the embedded membrane proteins with the gold electrodes and increasing the lateral diffusion of the bilayer, thus allowing for the incorporation of complex channels proteins which are failed in non-diluted systems. The tBLM is completed by fusion of liposomes made from a mixture of 1,2-diphythanolyl-sn-glycero-3-phosphocholine (DPhyPC), cholesterol, and 1,2-diphytanoyl-sn-Glycero-3-phosphate (DPhyPG) in a molar ratio of 6:3:1. Varying the mixing ratio, the optimum mixing ratio was obtained at a dilution factor of DPTL and TEGL at 90%:10%. Only under these conditions, the mixed tBLM showed electrical properties, as shown by EIS, which are comparable to a BLM. With higher dilution factors, a defect-free lipid bilayer was not formed. Formation of bilayers have been characterized by different techniques, such as surface plasmon resonance (SPR), electrochemical impedance spectroscopy (EIS), atomic force microscopy (AFM), and quartz crystal microbalance (QCM). Different proteins such as hemolysin, melittin, gramicidin, M2, Maxi-K, nAChR and bacteriohodopsin are incorporated into these tBLMs as shown by SPR and EIS studies. Ionic conductivity at 0 V vs. Ag|AgCl, 3M KCl were measured by EIS measurements. Our results indicate that these proteins have been successfully incorporated into a very stable tBLM environment in a functionally active form. Therefore, we conclude that the mixed tBLMs have been successfully designed as a general platform for biosensing and screening purposes of membrane proteins.

Theoretical studies of fluid membrane mechanics

Biologische Membranen sind Fettmolekül-Doppelschichten, die sich wie zweidimensionale Flüssigkeiten verhalten. Die Energie einer solchen fluiden Oberfläche kann häufig mit Hilfe eines Hamiltonians beschrieben werden, der invariant unter Reparametrisierungen der Oberfläche ist und nur von ihrer Geometrie abhängt. Beiträge innerer Freiheitsgrade und der Umgebung können in den Formalismus mit einbezogen werden. Dieser Ansatz wird in der vorliegenden Arbeit dazu verwendet, die Mechanik fluider Membranen und ähnlicher Oberflächen zu untersuchen. Spannungen und Drehmomente in der Oberfläche lassen sich durch kovariante Tensoren ausdrücken. Diese können dann z. B. dazu verwendet werden, die Gleichgewichtsposition der Kontaktlinie zu bestimmen, an der sich zwei aneinander haftende Oberflächen voneinander trennen. Mit Ausnahme von Kapillarphänomenen ist die Oberflächenenergie nicht nur abhängig von Translationen der Kontaktlinie, sondern auch von Änderungen in der Steigung oder sogar Krümmung. Die sich ergebenden Randbedingungen entsprechen den Gleichgewichtsbedingungen an Kräfte und Drehmomente, falls sich die Kontaktlinie frei bewegen kann. Wenn eine der Oberflächen starr ist, muss die Variation lokal dieser Fläche folgen. Spannungen und Drehmomente tragen dann zu einer einzigen Gleichgewichtsbedingung bei; ihre Beiträge können nicht mehr einzeln identifiziert werden. Um quantitative Aussagen über das Verhalten einer fluiden Oberfläche zu machen, müssen ihre elastischen Eigenschaften bekannt sein. Der "Nanotrommel"-Versuchsaufbau ermöglicht es, Membraneigenschaften lokal zu untersuchen: Er besteht aus einer porenüberspannenden Membran, die während des Experiments durch die Spitze eines Rasterkraftmikroskops in die Pore gedrückt wird. Der lineare Verlauf der resultierenden Kraft-Abstands-Kurven kann mit Hilfe der in dieser Arbeit entwickelten Theorie reproduziert werden, wenn der Einfluss von Adhäsion zwischen Spitze und Membran vernachlässigt wird. Bezieht man diesen Effekt in die Rechnungen mit ein, ändert sich das Resultat erheblich: Kraft-Abstands-Kurven sind nicht länger linear, Hysterese und nichtverschwindende Trennkräfte treten auf. Die Voraussagen der Rechnungen könnten in zukünftigen Experimenten dazu verwendet werden, Parameter wie die Biegesteifigkeit der Membran mit einer Auflösung im Nanometerbereich zu bestimmen. Wenn die Materialeigenschaften bekannt sind, können Probleme der Membranmechanik genauer betrachtet werden. Oberflächenvermittelte Wechselwirkungen sind in diesem Zusammenhang ein interessantes Beispiel. Mit Hilfe des oben erwähnten Spannungstensors können analytische Ausdrücke für die krümmungsvermittelte Kraft zwischen zwei Teilchen, die z. B. Proteine repräsentieren, hergeleitet werden. Zusätzlich wird das Gleichgewicht der Kräfte und Drehmomente genutzt, um mehrere Bedingungen an die Geometrie der Membran abzuleiten. Für den Fall zweier unendlich langer Zylinder auf der Membran werden diese Bedingungen zusammen mit Profilberechnungen kombiniert, um quantitative Aussagen über die Wechselwirkung zu treffen. Theorie und Experiment stoßen an ihre Grenzen, wenn es darum geht, die Relevanz von krümmungsvermittelten Wechselwirkungen in der biologischen Zelle korrekt zu beurteilen. In einem solchen Fall bieten Computersimulationen einen alternativen Ansatz: Die hier präsentierten Simulationen sagen voraus, dass Proteine zusammenfinden und Membranbläschen (Vesikel) bilden können, sobald jedes der Proteine eine Mindestkrümmung in der Membran induziert. Der Radius der Vesikel hängt dabei stark von der lokal aufgeprägten Krümmung ab. Das Resultat der Simulationen wird in dieser Arbeit durch ein approximatives theoretisches Modell qualitativ bestätigt.

Abscheidung und Charakterisierung von Plasmapolymerschichten auf Fluorkohlenstoff- und Siloxan-Basis

In dieser Arbeit wurden Fluorkohlenstoff-basierte und siliziumorganische Plasmapolymerfilme hergestellt und hinsichtlich ihrer strukturellen und funktionalen Eigenschaften untersucht. Beide untersuchten Materialsysteme sind in der Beschichtungstechnologie von großem wissenschaftlichen und anwendungstechnischen Interesse. Die Schichtabscheidung erfolgte mittels plasmachemischer Gasphasenabscheidung (PECVD) an Parallelplattenreaktoren. Bei den Untersuchungen zur Fluorkohlenstoff-Plasmapolymerisation stand die Herstellung ultra-dünner, d. h. weniger als 5 nm dicker Schichten im Vordergrund. Dies wurde durch gepulste Plasmaanregung und Verwendung eines Gasgemisches aus Trifluormethan (CHF3) und Argon realisiert. Die Bindungsstruktur der Schichten wurden in Abhängigkeit der eingespeisten Leistung, die den Fragmentationsgrad der Monomere im Plasma bestimmt, analysiert. Hierzu wurden die Röntgen-Photoelektronenspektroskopie (XPS), Rasterkraftmikroskopie (AFM), Flugzeit-Sekundärionenmassenspektrometrie (ToF-SIMS) und Röntgenreflektometrie (XRR) eingesetzt. Es zeigte sich, dass die abgeschiedenen Schichten ein homogenes Wachstumsverhalten und keine ausgeprägten Interfacebereiche zum Substrat und zur Oberfläche hin aufweisen. Die XPS-Analysen deuten darauf hin, dass Verkettungsreaktionen von CF2-Radikalen im Plasma eine wichtige Rolle für den Schichtbildungsprozess spielen. Weiterhin konnte gezeigt werden, dass der gewählte Beschichtungsprozess eine gezielte Reduzierung der Benetzbarkeit verschiedener Substrate ermöglicht. Dabei genügen Schichtdicken von weniger als 3 nm zur Erreichung eines teflonartigen Oberflächencharakters mit Oberflächenenergien um 20 mN/m. Damit erschließen sich neue Applikationsmöglichkeiten ultra-dünner Fluorkohlenstoffschichten, was anhand eines Beispiels aus dem Bereich der Nanooptik demonstriert wird. Für die siliziumorganischen Schichten unter Verwendung des Monomers Hexamethyldisiloxan (HMDSO) galt es zunächst, diejenigen Prozessparameter zu identifizieren, die ihren organischen bzw. glasartigen Charakter bestimmen. Hierzu wurde der Einfluss von Leistungseintrag und Zugabe von Sauerstoff als Reaktivgas auf die Elementzusammensetzung der Schichten untersucht. Bei niedrigen Plasmaleistungen und Sauerstoffflüssen werden vor allem kohlenstoffreiche Schichten abgeschieden, was auf eine geringere Fragmentierung der Kohlenwasserstoffgruppen zurückgeführt wurde. Es zeigte sich, dass die Variation des Sauerstoffanteils im Prozessgas eine sehr genaue Steuerbarkeit der Schichteigenschaften ermöglicht. Mittels Sekundär-Neutralteilchen-Massenspektrometrie (SNMS) konnte die prozesstechnische Realisierbarkeit und analytische Quantifizierbarkeit von Wechselschichtsystemen aus polymerartigen und glasartigen Lagen demonstriert werden. Aus dem Intensitätsverhältnis von Si:H-Molekülen zu Si-Atomen im SNMS-Spektrum ließ sich der Wasserstoffgehalt bestimmen. Weiterhin konnte gezeigt werden, dass durch Abscheidung von HMDSO-basierten Gradientenschichten eine deutliche Reduzierung von Reibung und Verschleiß bei Elastomerbauteilen erzielt werden kann.

Mimicking the pre-hairpin intermediate of gp41

A novel screening platform for potential retroviral fusion inhibitors on the basis of fully functional membrane‐anchored coiled coil lipopeptide receptors has been established. The work comprises the scrutiny of lateral organization of functional lipids in phase separated bilayers and an in‐depth investigation of the biophysical properties of lipopeptide‐based receptors. Lateral sorting of lipids was detected by the recognition of streptavidin of biotinylated lipids in phase separated bilayers and by nanoscopic patterns in mixed fluorocarbon / hydrocarbon lipid bilayers, employing temperature controlled atomic force microscopy (AFM) as a versatile characterization method. Particular features of fluorocarbon bilayers were additionally investigated in great detail by means of ellipsometry and ATR‐IR spectroscopy. Lipopeptide‐receptors were synthesized on the basis of a robust and reliable in situ coupling reaction by coupling terminal cysteine modified receptor‐peptides to a maleimide functionalized lipid bilayer. Receptor functionality of the lipopeptides was visualized by specific binding of vesicles and nanoparticles tracked by a multiplicity of characterization methods, such as AFM, ellipsometry, CLSM and fluorescence spectroscopy. Finally, in situ coupling of viral peptides, originating from the fusion protein of HIV resulted in a mimic of the pre‐hairpin intermediate of gp41. Structural analysis of N36‐lipopepides by means of CD‐spectroscopy in combination with FT‐IR spectroscopy revealed a coiled coil assembly of lipopeptides, which render the aggregates fully functional receptors for potent fusion inhibitors. Thereby, reversible inhibitor binding of T20 and the corresponding C‐ peptides was detected by AFM and ellipsometry, rendering coiled coil lipopeptides a new promising technique for screening of retroviral fusion inhibitors.