Numerical study of the impact of process variations on the motional resistance of weakly coupled MEMS resonators

This paper presents a numerical study of the impact of process-induced variations on the achievable motional resistance Rx of one-dimensional, cyclic and cross-coupled architectures of electrostatically transduced MEMS resonators operating in the 250 kHz range. Monte Carlo numerical simulations which accounted for up to 0.75% variation in critical resonator feature sizes were initiated on 1, 2, 3, 4, 5 and 9 coupled MEMS resonators for three distinct coupling architectures. Improvements of 100X in the spread of Rx and 2.7X in mean achievable Rx are reported for the case of 9 resonators when implemented in the cross-coupled topology, as opposed to the traditional one-dimensional chain. © 2013 IEEE.

The effect of carbon nanotube orientation on erosive wear resistance of CNT-epoxy based composites

Aligned carbon nanotube (CNT) polymer composites are envisioned as the next-generation composite materials for a wide range of applications. In this work, we investigate the erosive wear behavior of epoxy matrix composites reinforced with both randomly dispersed and aligned carbon nanotube (CNT) arrays. The aligned CNT composites are prepared in two different configurations, where the sidewalls and ends of nanotubes are exposed to the composite surface. Results have shown that the composite with vertically aligned CNT-arrays exhibits superior erosive wear resistance compared to any of the other types of composites, and the erosion rate reaches a similar performance level to that of carbon steel at 20° impingement angle. The erosive wear mechanism of this type of composite, at various impingement angles, is studied by Scanning Electron Microscopy (SEM). We report that the erosive wear performance shows strong dependence on the alignment geometries of CNTs within the epoxy matrix under identical nanotube loading fractions. Correlations between the eroded surface roughness and the erosion rates of the CNT composites are studied by surface profilometry. This work demonstrates methods to fabricate CNT based polymer composites with high loading fractions of the filler, alignment control of nanotubes and optimized erosive wear properties. © 2014 Elsevier Ltd. All rights reserved.

Insecticide resistance in Chinese populations of the Culex pipiens complex through esterase overproduction

In most parts of China, mosquitoes have been subjected to organophosphate (OP) insecticide treatments since the mid-1960s, and resistance gene monitoring in the Culex pipiens complex (Diptera: Culicidae) started in only a few locations from the end of the 1980s. Many resistant alleles at the Ester locus have been found in field populations, including those commonly found around the world (Ester(B1) and Ester(2)), and those endemic to China (Ester(B6), Ester(B7), Ester(8), and Ester(9)). This situation is atypical, and may represent a complex situation for the evolution of insecticide resistance genes in China. To increase our understanding of the Chinese situation and our ability to manage resistance in the C. pipiens complex, a large study was performed. Twenty field populations were sampled from Beijing to Guangzhou. Bioassays with five insecticides (dichlorvos, parathion, chlorpyrifos, 2-sec-butylphenyl methyl carbamate, and propoxur) disclosed resistance levels variable according to the geographic origin, and up to 85-fold for dichlorvos. Six overproduced esterases were identified, including two that have not been previously described. Most of them were found in all samples, although at variable frequencies, suggesting variable selection or a transient situation, e.g., each one was recently restricted to a particular geographic area. The results are discussed in the context of recent alterations to insecticide campaigns, and of the evolution of resistance genes in Chinese C. pipiens populations.

Molecular identification and expression analysis of natural resistance associated macrophage protein (Nramp) cDNA from Japanese flounder (Paralichthys olivaceus)

Natural resistance associated macrophage protein (Nramp) controls partially innate resistance to intracellular parasites. Its function is to enhance the ability of macrophages to kill pathogens. However, little is known about the structure and function of Nramp in lower vertebrates such as teleosts. We have recently isolated a cDNA encoding Nramp from Japanese flounder (Paratichthys olivaceus). The full-length cDNA of the Nramp is 3066 bp in length, including 224 bp 5' terminal UTR, 1662 bp encoding region and 1180 bp 3' terminal UTR. The 1662-nt open reading frame was found to code for a protein with 554 amino acid residues. Comparison of amino acid sequence indicated that Japanese flounder Nramp consists of 12 transmembrane (TM) domains. A consensus transport motif (CTM) containing 20 residues was observed between transmembrane domains 8 and 9. The deduced amino acid sequence of Japanese flounder had 77.30%, 82.71%, 82.67%, 79.64%, 80.72%, 90.97%, 91.16%, 60.14%, 71.48%, 61.69%, 72.37% identity with that of rainbow trout Nramp alpha and beta, channel catfish Nramp, fathead minnow Nramp, common carp Nramp, striped sea bass Nramp, red sea bream Nramp, mouse Nramp 1 and 2, human Nramp 1 and 2, respectively. RT-PCR indicated that Nramp transcripts were highly abundant in spleen, head kidney, abundant in intestine, liver and gill, and less abundant in heart. The level of Nramp mRNA in embryos gradually increases during embryogenesis from 4 h (8 cell stage) to 80 h (hatched stage) after fertilization. (c) 2005 Elsevier Ltd. All rights reserved.

Enhanced resistance to Aeromonas hydrophila infection and enhanced phagocytic activities in human lactoferrin-transgenic grass carp (Ctenopharyngodon idellus)

Human lactoferrin (hLF) is an iron-binding protein with antimicrobial and immunomodulatory activities. hLF cDNA was transferred into grass carp via electroporated sperm. The production of transgenic fish was as high as 55% tinder the best parameters. 2(11) pulses and 20-min incubation. The expression of the transgene was demonstrated by the detection of hLF mRNA by RT-PCR. We also investigated the response of G(0) transgenic grass carp to Aeromonas hydrophila infection. Serum lysozyme activities (P>0.05) and phagocytic activities of kidney cells (P<0.05) were measured in transgenic individuals. The transgenic fish not only cleared A. hydrophila significantly faster than the control carp (P<0.05), but also showed enhanced phagocytic activities. The result shows that hLF has immunomodulatory activities in hLF-transgenic grass carp. The transgenic grass carp exhibited enhanced immunity to A. hydrophila infection. These results reveal that the mechanisms of disease resistance are different between hLF-transgenic plants and hLF-transgenic grass carp. (C) 2004 Elsevier B.V. All rights reserved.

Thermal shock resistance of air plasma sprayed thermal barrier coatings

The spallation resistance of an air plasma sprayed (APS) thermal barrier coating (TBC) to cool-down/reheat is evaluated for a pre-existing delamination crack. The delamination emanates from a vertical crack through the coating and resides at the interface between coating and underlying thermally grown oxide layer (TGO). The coating progressively sinters during engine operation, and this leads to a depth-dependent increase in modulus. Following high temperature exposure, the coating is subjected to a cooling/reheating cycle representative of engine shut-down and start-up. The interfacial stress intensity factors are calculated for the delamination crack over this thermal cycle and are compared with the mode-dependent fracture toughness of the interface between sintered APS and TGO. The study reveals the role played by microstructural evolution during sintering in dictating the spallation life of the thermal barrier coating, and also describes a test method for the measurement of delamination toughness of a thin coating. © 2014 Elsevier Ltd.

Effects of heavy metals on plants and resistance mechanisms

Goal, Scope and Background. As one of the consequences of heavy metal pollution in soil, water and air, plants are contaminated by heavy metals in some parts of China. To understand the effects of heavy metals upon plants and the resistance mechanisms, would make it possible to use plants for cleaning and remediating heavy metal-polluted sites. Methods. The research results on the effects of heavy metals on plants and resistant mechanisms are compiled from Chinese publications from scientific journals and university journals, mostly published during the last decade. Results and Discussion. Effects of heavy metals on plants result in growth inhibition, structure damage, a decline of physiological and biochemical activities as well as of the function of plants. The effects and bioavailability of heavy metals depend on many factors, such as environmental conditions, pH, species of element, organic substances of the media and fertilization, plant species. But, there are also studies on plant resistance mechanisms to protect plants against the toxic effects of heavy metals such as combining heavy metals by proteins and expressing of detoxifying enzyme and nucleic acid, these mechanisms are integrated to protect the plants against injury by heavy metals. Conclusions. There are two aspects on the interaction of plants and heavy metals. On one hand, heavy metals show negative effects on plants. On the other hand, plants have their own resistance mechanisms against toxic effects and for detoxifying heavy metal pollution. Recommendations and Outlook. To study the effects of heavy metals on plants and mechanisms of resistance, one must select crop cultivars and/or plants for removing heavy metals from soil and water. More highly resistant plants can be selected especially for a remediation of the pollution site. The molecular mechanisms of resistance of plants to heavy metals should be studied further to develop the actual resistance of these plants to heavy metals. Understanding the bioavailability of heavy metals is advantageous for plant cultivation and phytoremediation. Decrease in the bioavailability to farmlands would reduce the accumulation of heavy metals in food. Alternatively, one could increase the bioavailability of plants to extract more heavy metals.

Introduction of the human lactoferrin gene into grass carp (Ctenopharyngodon idellus) to increase resistance against GCH virus

Haemorrhage can be an epidemic and fatal condition in grass carp. It is known now that the Grass Carp Haemorrhage Virus (GCHV) triggers haemorrhage. Human lactoferrin (hLF) plays an important role in the non-specific immune system, making some organisms more resistant to some viruses. Sperm of grass carp was mixed with linearized pCAhLFc, which is a DNA construct containing an hLF cDNA and the promoter of common carp beta-actin gene, and then electroporated. Then, mature eggs were fertilized in vitro with the treated sperm cells. The fry were sampled and analyzed by polymerase chain reaction (PCR). Results indicated that the foreign gene had been transferred successfully into the cells of some fry. Under optimal electroporation conditions, the efficiency of gene transfer was as high as 46.8%. About 35.7% of treated 5-month-old grass carp contained foreign genes. Most transgenic fry demonstrated significant delays in onset of symptoms of haemerrhage after injection of GCHV, suggesting a significant positive relationship between hLF cDNA and levels of disease resistance (P < 0.01). Results suggest that transgenic grass carp could be bred for increased resistance to haemorrhage. (C) 2002 Elsevier Science B.V. All rights reserved.

Domain wall resistance in perpendicular (Ga,Mn) As: Dependence on pinning

We have investigated the domain wall resistance for two types of domain walls in a (Ga,Mn)As Hall bar with perpendicular magnetization. A sizeable positive intrinsic DWR is inferred for domain walls that are pinned at an etching step, which is quite consistent with earlier observations. However, much lower intrinsic domain wall resistance is obtained when domain walls are formed by pinning lines in unetched material. This indicates that the spin transport across a domain wall is strongly influenced by the nature of the pinning.

Easy axis reorientation and magneto-crystalline anisotropic resistance of tensile strained (Ga,Mn)As films

We present a study of magnetic anisotropy by using magneto-transport and direct magnetization measurements on tensile strained (Ga,Mn)As films. The magnetic easy axis of the films is in-plane at low temperatures, while the easy axis flips to out-of-plane when temperature is raised or hole concentration is increased. This easy axis reorientation is explained qualitatively in a simple physical picture by Zeners pd model. In addition, the magneto-crystalline anisotropic resistance was also investigated experimentally and theoretically based on the single magnetic domain model. The dependence of sheet resistance on the angle between the magnetic field and [1 0 0] direction was measured. It is found that the magnetization vector M in the single-domain state deviates from the external magnetic field H direction at low magnetic field, while for high magnetic field, M continuously moves following the field direction, which leads to different resistivity function behaviors.

Influence factors on wear resistance of two alumina matrix composites

We measured the wear resistances of alumina, alumina/silicon carbide composite and alumina/mullite composite by abrasive wear. And we studied the influence of fracture mode and worn surface pullout on wear resistance. The results are as follows: the main wear mechanisms of alumina and alumina/silicon carbide were fracture wear and plastic wear respectively, and for alumina/mullite composite, fracture wear and plastic wear mechanisms worked together. The wear resistance of the alumina/silicon carbide composite and the alumina/mullite composite was better by a factor of 1 similar to 3 than that of the monolithic alumina. There were two main reasons for the better wear resistance, i.e., the improved mechanical properties and the more smooth worn surfaces. However, The primary reason was the reduction of area fraction of pullout on the worn surfaces induced by fracture mode transition. (C) 2007 Published by Elsevier B.V.

Wear resistance of reaction sintered alumina/mullite composites

Alumina and alumina/mullite composites with mullite content of 0.96-8.72 vol.% were subjected to an abrasive wear test under loads of 0.1-2.0 N with a ball-on-disc apparatus. The wear rate and area fraction of pullout f(po) on the worn surfaces were measured. The wear resistances of the alumina/mullite composites were better by a factor of 1-2 than that of pure alumina. The main wear mechanism of alumina is fracture wear, and for alumina/mullite composites, fracture wear and plastic wear mechanisms work together. The influence of mechanical properties on wear resistance was estimated by Evans' method. It was found that the wear rate depends on f(po), and the primary reason for the better wear resistance of alumina/mullite composites is the reduction off, induced by fracture mode transition. (c) 2007 Elsevier B.V. All rights reserved.

A simple ac bridge for detecting small resistance change

A simple ac resistance bridge is proposed. The stability of the design is better than 10(-6), which is especially suitable for detecting tiny changes of resistance. An example of magnetoresistance measurement for a 220 nm Au film shows the good performance of the bridge. (C) 2009 American Institute of Physics. [DOI: 10.1063/1.3202284]