Development of an Active Superconducting Magnetic Bearing

The potential use of YBa2Cu3C7as an active component in a magnetic bearing is being investigated. Measurements are being made of the load bearing capacity and related stiffnesses in comparison to predictions from the critical state model. Although the load bearing capacity is high and increases with the square of the magnetic field trapped the stiffness is low. We report on a novel design concept to overcome this problem. © 1995 IEEE

The development of aerodynamic performance measurements in a transient test facility

Transient test facilities offer the potential for the simultaneous study of turbine aerodynamic performance, unsteady flow phenomena and the heat transfer characteristics of a turbine stage. This paper describes the development of aerodynamic performance measurement techniques in the Oxford Rotor Facility (ORF). The solutions to the technological issues involved with transient testing presented in this paper are expected to achieve levels of precision uncertainty comparable with traditional steady flow test rigs. The theoretical background to the measurement of aerodynamic performance is presented together with a comprehensive pre-test uncertainty analysis. The instrumentation scheme for the measurement of stage mass flow rate is discussed in detail, the measurements of shaft power, total inlet enthalpy, and stage pressure ratio are also outlined. The current working section features a 62% scale, 1-1/2 stage, high-pressure shroudless transonic turbine. The required inlet flow conditions are provided by an Isentropic Light Piston Tunnel (ILPT) with a quasi-steady state run time of approximately 70ms. The testing is conducted at engine representative specific speed, pressure ratio, gas-to-wall temperature ratio, Mach number and Reynolds number.

Ornamental fish resources of Manipur: potentials, problems and strategies for development

The study revealed 125 species of fishes in Manipur of which 95 species belonging to 48 genera and 22 families have ornamental value. Fifty percent of these belonged to the family Cyprinidae, 7% to Cobitidae, 5% to Sisoridae 7% to Balitoridae, 3% to Channidae, 8% to Bagridae, 2% each to Chandidae and Mastacembelidae. Species representation in other families (16%) includes 1.6% each in Belonidae, Nandidae, Notopteridae, Psilorhynchidae, Schilbeidae and 0.8% each in Amblydpitidae, Anabantidae, Aplocheilidae, Belonidae,Chacidae, Clupeidae, Mugilidae, Symbranchidae, Siluridae and Tetradontidae. The conservation status of fishes showed that 25.6% of them have not been evaluated, 21.6% are vulnerable, 16.0% are endangered and 2.4% are critically endangered. "Low risk near threatened" category amounted to 25.6% and only 6.4% in "low risk least concern" category. Hence a cautious and regulated approach needs to be adopted while promoting ornamental fish trade. Suitable strategies for developing a viable ornamental fish trade in the state are discussed.

Coastal development and pollution impact on the distribution of macrobenthic communities along the eastern coast of the Gulf of Suez (Egypt)

The configuration for the eastern side of the Gulf of Suez was studied over 241 km from Ras Mohammed to Ras Sudr including 35 station. Litters, tar balls and aged oil patches aggregated in considerable amounts on the beach and shore line of the middle part due to the oil spills from off-shore oil wells. A large reef flat in the shallow intertidal waters exists at stations 1 and 2 (Ras Mohammed, Protected area) and spars coral patches are less frequent at the Stations from 7 to 13. Density and diversity of marine benthos were higher on hard and cobble bottoms compared to muddy sand and sandy substrates. The assemblages of the benthic fauna are dominated by the gastropod Courmya (Thericium) vulgata; the bivalve Brachiodontes variabilis, and the barnacles Chthamalus stellatus, Balanus amphitrite and Tetraclita rubescens. The distribution of the algal cover in the intertidal region shows high abundance of the brown algae, Sargassum latifolium; padina pavonica and Cystoseira trinodis rather than the green and red algae. These species are found in both polluted and unpolluted areas. The changes in benthic structures in the study area depend not only on the state of pollution but also on the type of substrates.

Modular risk modeling and management of water infrastructure disaster incidents

Water supply and wastewater control are critical elements of society's infrastructure. The objective of this study will be to provide a generic risk assessment tool to provide municipalities and the nation as a whole with a quantifiable assessment of their vulnerability to water infrastructure threats. The approach will prioritize countermeasures and identify where research and development is required to further minimize risk. This paper outlines the current context, primary concerns and state-of-the art in critical infrastructure risk management for the water sector and proposes a novel approach to resolve existing questions in the field. The proposed approach is based on a modular framework that derives a quantitative risk index for varied domains of interest. The approach methodology is scaleable and based on formal definitions of event probability and severity. The framework is equally applicable to natural and human-induced hazard types and can be used for analysis of compound risk events.

The state of mangroves

The article presents the current state of mangroves in Southeast Asia. In several countries lost mangrove areas were due to the conversion of mangrove forest into aquaculture and other uses. The ecological and socioeconomic effects of mangrove destruction are also presented.

Biofluid behaviour in 3D microchannel systems: Numerical analysis and design development of 3D microchannel biochip separators

This paper describes the design and development cycle of a 3D biochip separator and the modelling analysis of flow behaviour in the biochip microchannel features. The focus is on identifying the difference between 2D and 3D implementations as well as developing basic forms of 3D microfluidic separators. Five variants, based around the device are proposed and analysed. These include three variations of the branch channels (circular, rectangular, disc) and two variations of the main channel (solid and concentric). Ignoring the initial transient behaviour and assuming steady state flow has been established, the efficiencies of the flow between the main and side channels for the different designs are analysed and compared with regard to relevant biomicrofluidic laws or effects (bifurcation law, Fahraeus effect, cell-free phenomenon, bending channel effect and laminar flow behaviour). The modelling results identify flow features in microchannels, a constriction and bifurcations and show detailed differences in flow fields between the various designs. The manufacturing process using injection moulding for the initial base case design is also presented and discussed. The work reported here is supported as part of the UK funded 3D-MINTEGRATION project. © 2010 IEEE.

Defining product-service network configurations and location roles: A current and future state analysis framework for international engineering operations

Many manufacturing firms have developed a service dimension to their product portfolio. In response to this growing trend of servitisation, organisations, often involved in complex, long-lifecycle product-service system (PSS) provision, need to reconfigure their global engineering networks to support integrated PSS offerings. Drawing on parallel concepts in 'production' networks, the idea of 'location role' now becomes increasingly complex, in terms of service delivery. As new markets develop, locations in a specific region may need to grow/adapt engineering service 'competencies' along the value chain, from design and build to support and service, in order to serve future location-specific requirements and, potentially, those requirements of the overall network. The purpose of this paper is to advance understanding of how best to design complex multi-organisational engineering service networks, through extension of the 'production' network location role concept to a PSS context, capturing both traditional engineering 'design and build' and engineering 'service' requirements. Copyright © 2012 Inderscience Enterprises Ltd.

Top Management Involvement in New Product Development: A Review and Synthesis

Established literature on new product development (NPD) management recognizes top management involvement (TMI) as one of the most critical success factors. With increasing pressure to sustain competitive advantage and growth, NPD activities remain the focus of close interest from top management in many organizations. TMI in the NPD domain is receiving increasing academic attention. Despite its criticality, there is no systematic review of the existing literature to inform and stimulate researchers in the field for further investigation. This paper introduces the current state of literature on TMI in NPD, synthesizes important findings, and identifies the gaps and deficiencies in this research stream. The contents of the selected articles, which investigated TMI in NPD, are analyzed based on the type of the study, level of analysis, research methodology, operationalization of TMI, and main findings. Additionally, other studies, which did not directly investigate TMI and support in NPD, but were sufficiently related, are briefly summarized. As a result of this detailed literature review, it can be stated that both exploratory and relational studies provide rich evidence on the critical role of top management in NPD. However, the identified gaps and deficiencies in this research stream call for a better theoretical understanding and well-defined constructs of TMI in the NPD domain for different levels of analysis for future studies.

Evolutionary Conservation of Dazl Genomic Organization and its Continuous and Dynamic Distribution Throughout Germline Development in Gynogenetic Gibel Carp

To investigate germline development and germ cell specification, we identified a Dazl homolog (CagDazl) from gynogenetic gibel carp (Carassius auratus gibelio). Its cDNA sequence and BAC clone sequence analyses revealed the genomic organization conservation and conserved synteny of the Dazl family members and their neighborhood genes among vertebrates, especially in fish. Moreover, a polyclonal antibody specific to CagDazl was produced and used to examine its expression and distribution throughout germline development at protein level. Firstly, ovary-specific expression pattern of CagDazl was confirmed in adult tissues by RT-PCR and Western blot. In addition, in situ hybridization and immunofluorescence localization demonstrated its specific expression in germ cells, and both its transcript and protein were localized to germ plasm. Then, co-localization of CagDazl and mitochondrial cloud was found, confirming that CagDazl transcript and its protein are germ plasm component and move via METRO pathway during oogenesis. Furthermore, the CagDazl is abundant and continuous throughout germline development and germ cell specification including primordial germ cell (PGC) formation, oogonium differentiation, oocyte development, and embryogenesis, and the dynamic distribution occurs at different development stages. The data suggest that maternal CagDazl might play an important role in gibel carp PGC formation. Therefore, CagDazl is a useful and specific marker for tracing germ plasm and germ cell development in the gynogenetic gibel carp. In addition, in comparison with previous studies in sexual reproduction species, the continuous and dynamic distribution of CagDazl protein in the germ plasm throughout the life cycle seems to have significant implication in sex evolution of vertebrates. J. Exp. Zool. (Mol. Deu. Euol.) 312B:855-871, 2009. (C) 2009 Wiley-Liss, Inc.

Analysis on the off-state design and characterization of LIGBTs in partial SOI technology

Classical high voltage devices fabricated on SOI substrates suffer from a backside coupling effect which could result in premature breakdown. This phenomenon becomes more prominent if the structure is an IGBT which features a p-type injector. To suppress the premature breakdown due to crowding of electro-potential lines within a confined SOI/buried oxide structure, the partial SOI (PSOI) technique is being introduced. This paper analyzes the off-state behavior of an n-type Superjunction (SJ) LIGBT fabricated on PSOI substrate. During the initial development stage the SJ LIGBT was found to have very high leakage. This was attributed to the back and side coupling effects. This paper discusses these effects and shows how this problem could be successfully addressed with minimal modifications of device layout. The off-state performance of the SJ LIGBT at different temperatures is assessed and a comparison to an equivalent LDMOSFET is given. © 2014 Elsevier Ltd. All rights reserved.

First-principles study of ground-state properties and high pressure behavior of ThO2

The mechanical properties, electronic structure and phonon dispersion of ground state ThO2 as well as the structure behavior up to 240 GPa are studied using first-principles density-functional theory. Our calculated elastic constants indicate that both the ground-state fluorite structure and high pressure cotunnite structure of ThO2 are mechanically stable. The bulk modulus, shear modulus, and Young's modulus of cotunnite ThO2 are all smaller by approximately 25% compared with those of fluorite ThO2. The Poisson's ratios of both structures are approximately equal to 0.3 and the hardness of fluorite ThO2 is 22.4 GPa. The electronic structure and bonding nature of fluorite ThO2 are fully analyzed, and show that the Th-O bond displays a mixed ionic/covalent character. The phase transition from the fluorite to cotunnite structure is calculated to occur at the pressure of 26.5 GPa, consistent with recent experimental measurement by ldiri et al. [1]. For the cotunnite phase it is further predicted that an isostructural transition takes place in the pressure region of 80-130 GPa.

The status, limits and countermeasures in the development of the silicon microelectronics industry

In this paper.. the status and limits in the development of the silicon microelectronics industry are presented briefly. The key countermeasures given are use of the new structure materials and the new device structures.

Self-Heating Effect on the Two-State Lasing Behaviors in 1.3-mu m InAs-GaAs Quantum-Dot Lasers

Experimental and theoretical study of the self-heating effect on the two-state lasing behaviors in 1.3-mu m self-assembled InAs-GaAs quantum dot (QD) lasers is presented. Lasing spectra under different injected currents, light-current (L-I) curves measured in continuous and pulsed regimes as well as a rate-equation model considering the current heating have been employed to analyze the ground-state (GS) and excited-state (ES) lasing processes. We show that the self-heating causes the quenching of the GS lasing and the ES lasing by the increased carrier escape rate and the reduced maximum modal gain of GS and ES.

Fermi-Level Pinning at Metal/High-k Interface Influenced by Electron State Density of Metal Gate

The Fermi-level pinning (FLP) at the metal/high-k interface and its dependence on the electron state density of the metal gate are investigated. It is found that the FLP is largely determined by the distortion of the vacuum level of the metal which is quantitatively ruled by the electron state density of the metal. The physical origin of the vacuum level distortion of the metal is attributed to an image charge of the interface charge in the metal. Such results indicate that the effective work function of the metal/high-k stack is also governed by the electron state density of the metal.