Sequential spectrophotometric determination of chromium(III) and chromium(VI) using flow injection analysis

A flow injection analysis (FIA) procedure for the speciation of Cr(III) and Cr(VI) using the 1,5-diphenylcarbazide (DPC) method is presented. As Cr(III) does not interfere in the Cr(VI) - DPC reaction, both Cr(VI) and total chromium [after the on-line oxidation of Cr(III) by Ce(IV)] are sequentially determined. Cr(III) is obtained by difference. Under the experimental conditions described, the calibration graphs are linear up to 2 μg mh1 of Cr(VI) and 4 μg ml-1 of Cr(III). The detection limits found were 18 ng ml -1 for Cr(VI) and 55 ng ml-1 for Cr(III), at a signal to noise ratio of 3. The common interfering elements in the Cr(VI) - DPC reaction were investigated under dynamic FIA conditions. The FIA method was also compared with the conventional spectrophotometric procedure.

Thermal decomposition of the hydrated basic carbonates of lanthanides and yttrium in CO2 atmosphere

The hydrated basis carbonates of lanthanides and yttrium were prepared by precipitation from homogeneous solution via the hydrolysis of urea, without the addition of an auxiliary anion. Thermogravimetry, derivative thermogravimetry (TG-DTG), and differential thermal analysis (DTA) have been used in the study of these compounds in CO2 atmosphere. The results lead to the composition and thermal stability of the studied compounds, and also to a comparative study with reported results in air atmosphere. © 1993.

EFEIFOS DO SULFATE DE MAGNESIO NA HEMODINAMICA CARDIOVASCULAR DE CAES ANESTESIADOS COM PENTOBARBITAL SODICO

Background and Objectives - A controversy exists in the literature regarding the effects of the acute administration of magnesium on the cardiovascular system of animals and humans. The purpose of this study was to evaluate the effects of hypermagnesemia on the cardiovascular hemodynamics of dogs. Methods - Sixteen mongrel dogs were anesthetized with pentobarbitone 30 mg.kg-1 and submitted to volume expansion with Ringer's solution (0.4 ml.kg-1.min-1 and mechanical ventilation with room air. In this model, the hemodynamic repercussions of the following drugs and doses were studied. pentobarbitone 5 mg.kg-1 Group 1, control - and the association of pentobarbitone and magnesium sulphate (MS), at the dose of 140 mg.kg-1 injected in 15 minutes, followed by an infusion of 80 mg.kg-1.h-1 - Group 2. The parameters studied were: heart rate, blood pressure, inferior vena cava pressure, cardiac index, systolic index and peripheral resistance index, evaluated at 5 different moments: 15(M1), 30(M2), 60(M3) and 75(M4) minutes after the first suppplementary dose of pentobarbitone and 15 minutes (M5) after the second supplementary dose. In Group 2, the moments M3, M4, M5 corresponded to 15, 30 and 60 minutes after the priming dose of magnesium sulphate. Results - Group 1 animals exhibited tachycardia since the beginning of the experiment. There was a decrease in the cardiac index, in the systolic index and an increase in the inferior vena cava pressure. Group 2 animals also exhibited tachycardia, but heart rate decreased after MS infusion. The blood pressure and the peripheral resistance index decreased. The systolic index increased and the cardiac index decreased only at the end of the experiment. Conclusions: The antiadrenergic effects of MS could have been responsible for the decrease in heart rate. The vasodilating effects of the magnesium induced the decrease in the peripheral resistance index. The systolic index increased, showing that myocardial depression did not occur.

EFEITOS DO SULFATE DE MAGNESIO NA HEMODINAMICA E FUNCAO RENAL DE CAES ANESTESIADOS CORN PENTOBARBITAL SODICO

Background and objectives - The use of magnesium sulphate for the prevention of seizures in pre-eclampsia may induce hypermagnesemia. Clinical and experimental studies are not in agreement about the effects of magnesium on the renal hemodynamics and function. We therefore studied the effects of hypermagnesemia on the renal hemodynamics and function of dogs anesthetized with pentobarbitone. Methods - Sixteen mongrel dogs were anesthetized with pentobarbitone 30 mg.kg-1 and submitted to extracellular ) and mechanical ventilation with room air. The dogs were volume expansion with Ringer's solution (0.4 ml.kg.min allocated into two groups of 8 animals, for the study of renal hemodynamics and function following the administration of 5 mg.kg-1 of pentobarbitone (Group 1 - control or of pentobarbitone associated with magnesium sulphate in the dose (Group 2). The parameters studied were: PAH of 140 mg.kg, administered in 15 minutes, followed by 80 mg.kg-1.h-1 clearance, creatinine clearance, osmolar clearance, free water clearance, renal blood flow, renal vascular resistance, filtration fraction, urinary volume, plasmatic and urinary osmolarity, urinary and fractionary excretion of sodium and potassium, measured at five moments: 15 (M1), 30 (M2), 60 (M3) and 75 (M4) minutes after the first supplementary dose of pentobarbitone and 15 minutes (M5) after the second supplementary dose in Group 1. In Group 2, the moments M3, M4, M5 were 15, 30 and 60 minutes after the priming dose of magnesium sulphate and during the maintenance dose. Results - In Group I no significant changes were observed in renal hemodynamic parameters and creatinine clearance. The extracellular volume expansion increased urinary volume and decreased urinary osmolarity as a consequence of sodium, potassium and free water clearance. The fractionary excretion of sodium was maintained. The plasmatic osmolarity increased. In Group 2, renal hemodynamic parameters and creatinine clearance were also maintained. There was an increase in renal sodium clearance, as detected by the increase in the fractionary excretion of sodium. Conclusions - Magnesium sulphate did not produce significant changes in renal hemodynamics and facilitated the renal excretion of sodium in dogs anesthetized with pentobarbitone.

Optical properties of chromium-doped fluoroindate glasses

This work reports on the optical properties of Cr3+ ions in the pseudoternary system InF3-GdF3-GaF3. Linear properties, investigated through absorption and emission spectra, provide information on the crystal field, the frequency, and number of phonons emitted during the absorption to the 4T2 band and the emission to the 4A2 ground state, and the Fano antiresonance line shape in the vicinity of the 4A2→2E transition. A study of the nonlinear refractive index as a function of the wavelength, carried out with the Z-scan technique, provides spectroscopic data about electronic transitions starting from the excited state.

Chromium-containing silica materials

Chromium-containing silica samples were obtained from soluble sodium silicate solutions in the presence of different chromium nitrate concentrations. Precipitation was carried out in ethanolic media. Gel precipitate was dried by liophylization and samples measured by transmission electron microscopy (TEM), X-ray energy-dispersive spectrometer, X-ray mapping, X-ray photoemission spectroscopy (XPS), and particle size analysis. Spherical chromium containing silica particles with 3.5% and 4.8% (at.%) of chromium were obtained. Particle size analysis results showed that with increased addition of chromium in sodium silicate solutions produces agglomerates whose sizes range from 1 to 0.2 μm. Chromium mapping and XPS results show that chromium oxide is preferentially segregated on particle surfaces. Chromium oxide was detected on particle surface with a binding energy of 576.77 ± 0.05 eV as obtained from XPS analysis. During the hydrolysis and condensation processes chromium oxide precipitates on the silica surface and it affects the silica chain size. © 2000 Elsevier Science B.V. All rights reserved.

Effects of tungsten carbide thermal spray coating by HP/HVOF and hard chromium electroplating on AISI 4340 high strength steel

In cases of decorative and functional applications, chromium results in protection against wear and corrosion combined with chemical resistance and good lubricity. However, pressure to identify alternatives or to improve conventional chromium electroplating mechanical characteristics has increased in recent years, related to the reduction in the fatigue strength of the base material and to environmental requirements. The high efficiency and fluoride-free hard chromium electroplating is an improvement to the conventional process, considering chemical and physical final properties. One of the most interesting, environmentally safer and cleaner alternatives for the replacement of hard chrome plating is tungsten carbide thermal spray coating, applied by the high velocity oxy-fuel (HVOF) process. The aim of this study was to analyse the effects of the tungsten carbide thermal spray coating applied by the HP/HVOF process and of the high efficiency and fluoride-free hard chromium electroplating (in the present paper called 'accelerated'), in comparison to the conventional hard chromium electroplating on the AISI 4340 high strength steel behaviour in fatigue, corrosion, and abrasive wear tests. The results showed that the coatings were damaging to the AISI 4340 steel behaviour when submitted to fatigue testing, with the tungsten carbide thermal spray coatings showing the better performance. Experimental data from abrasive wear tests were conclusive, indicating better results from the WC coating. Regarding corrosion by salt spray test, both coatings were completely corroded after 72 h exposure. Scanning electron microscopy technique (SEM) and optical microscopy were used to observe crack origin sites, thickness and adhesion in all the coatings and microcrack density in hard chromium electroplatings, to aid in the results analysis. © 2001 Elsevier Science B.V. All rights reserved.

Electromyographic validation of basic exercises for physical conditioning programmes IV. Analysis of the deltoid muscle (anterior portion) and pectoralis major muscle (clavicular portion) in frontal-lateral cross, dumbbells exercises

The electromyographic activity of the shoulder muscles deltoid - anterior portion (DA) and pectoralis major - clavicular portion (PMC) was tested on 24 male volunteers using a 2 channel TEC A TE4 electromyograph and Hewlett Packard surface electrodes during the execution of four different modalities of frontal-lateral cross, dumbbells exercises. The results showed that all of the tested exercises developed high levels of action potential for both muscles. So, we jusfity the indication of all of them for physical fitness programmes for DA and PMC. Some suggestions to the use of the tested exercises are presented.

Electromyographic validation of basic exercises for physical conditioning programmes V. The comparison of the response in the deltoid muscle (anterior portion) and the pectoralis major muscle (clavicular portion) determined by the frontal-lateral cross, dumbbells and the rowing exercises

The action potential level for shoulder muscles deltoid-anterior portion (DA) and pectoralis major-clavicular portion (PMC) determined by four different modalities of execution of rowing exercises, each one with two different grips, was recorded. These were compared with the action potential level determined for the same muscles by four different modalities of execution of the frontal-lateral cross, dumbbells exercises. Twenty-four male volunteers were examined using a 2 channel TECA TE4 electromyograph and Hewlett Packard surface electrodes. The statistic analysis showed significant (p<0,05) superiority for all the frontal-lateral cross, dumbbells exercises in comparison to all rowing exercises for the PMC, for the DA this generalized supremacy was not observed.

Evaluation of the genotoxic potential due to the action of an effluent contaminated with chromium, by the comet assay in CHO-K1 cultures

The comet assay technique has been considered to be more efficient in the biomonitoring of aquatic environments that the micronucleus and sister chromatid exchange techniques. The comet assay has been used to determine breaks in the DNA strands of organisms exposed to pollutants with a genotoxic potential. The comet technique was applied to CHO-K1 cells in order to evaluate the genotoxic potential of the waters of the Sapucaizinho River (Municipality of Patrocínio Paulista, State of São Paulo, Brazil), which receive tannery effluents and therefore are contaminated with chromium. The results indicated high genotoxicity of the waters collected at sites located downstream from the emission of tannery effluents, where the concentration of chromium was found to be high.

Bone healing in surgically created defects treated with either bioactive glass particles, a calcium sulfate barrier, or a combination of both materials: A histological and histometric study in rat tibias

Objective: The purpose of this study was to histologically analyze the influence of bioactive glass and/or a calcium sulfate barrier on bone healing in surgically created defects in rat tibias. Material and methods: Sixty-four rats were divided into 4 groups: C (control), CS (calcium sulfate), BG (bioactive glass), and BG/CS (bioactive glass/calcium sulfate). A surgical defect was created in the tibia of each animal. In Group CS, a calcium sulfate barrier was placed to cover the defect. In Group BG the defect was filled with bioactive glass. In Group BG/CS, it was filled with bioactive glass and protected by a barrier of calcium sulfate. Animals were sacrificed at 10 or 30 days post-operative. The formation of new bone in the cortical area of the defect was evaluated histomorphometrically. Results: At 10 days post-operative, Group C presented significantly more bone formation than Groups CS, BG, or BG/CS. No statistically significant differences were found between the experimental groups. At 30 days post-operative, Group C demonstrated significantly more bone formation than the experimental groups. Groups CS and BG/CS showed significantly more bone formation than Group BG. No statistically significant differences were found between Group CS and BG/CS. Conclusions: (a) the control groups had significantly more bone formation than the experimental groups; (b) at 10 days post-operative, no significant differences were found between any of the experimental groups; and (c) at 30 days post-operative, the groups with a calcium sulfate barrier had significantly more bone formation than the group that used bioactive glass only. Copyright © Blackwell Munksgaard 2005.

Efeito da calagem e sulfato de amônio no algodão. I - Transporte de cátions e ânions no solo

Applying lime on the soil surface in soils managed under no-tillage has caused an excess of basic cations in the most superficial layers of the soil profile. On the other hand, subsoil acidity is considered a constraint to the development of deep plant roots. The objective of this study was to evaluate Ca 2+, Mg 2+, NO 3- and SO 4 2- leaching in the soil profile as affected by liming and top dressing nitrogen fertilization in cotton, grown with straw cover on the soil surface. Cotton plants (Gossypium hirsutum) were grown for 60 days in PVC columns filled with a Distroferric Red Latosol (sand loam Rhodic Oxisol) with liming applied over the straw on the soil surface, incorporated liming 0-20 cm deep, or without liming. Nitrogen was applied at rates of 0, 50, 100 and 150 kg ha -1 as ammonium sulfate. The PVC columns were set up in layers of 0-5, 5-10, 10-20, 20-30 and 30-30 cm, totaling 15.71 dm 3. The ammonium sulfate application caused intense leaching of SO 4 2- in the soil, irrespective of the lime application method. Liming increased the concentration of NO 3 in the 0-20 cm soil layer, whereas the correction of the soil acidity did not affect the NO 3- concentration in the 30-50 cm soil layer. The influence of ammonium sulfate on Ca 2+ leaching below 20 cm was only observed in the soil with incorporated lime. Nitrogen application resulted in extensive Mg 2+ leaching from the soil, regardless of the lime application method. In the soil layer below 30 cm, SO 4 2- presented a higher correlation than NO 3- in the formation of ionic pairs with Ca 2+ and Mg 2+.

Autogenous bone graft with or without a calcium sulfate barrier in the treatment of class II furcation defects: A histologic and histometric study in dogs

Background: The purpose of this study was to histologically evaluate the healing of surgically created Class II furcation defects treated using an autogenous bone (AB) graft with or without a calcium sulfate (CS) barrier. Methods: The second, third, and fourth mandibular premolars (P2, P3, and P4) of six mongrel dogs were used in this study. Class II furcation defects (5 mm in height × 2 mm in depth) were surgically created and immediately treated. Teeth were randomly divided into three groups: group C (control), in which the defect was filled with blood clot; group AB, in which the defect was filled with AB graft; and group AB/CS, in which the defect was filled with AB graft and covered by a CS barrier. Elaps were repositioned to cover all defects. The animals were euthanized 90 days post-surgery. Mesio-distal serial sections were obtained and stained with either hematoxylin and eosin or Masson's trichrome. Histometric, using image-analysis software, and histologic analyses were performed. Linear and area measurements of periodontal healing were evaluated and calculated as a percentage of the original defect. Percentage data were transformed into arccosine for statistical analysis (analysis of variance; P<0.05). Results: Periodontal regeneration in the three groups was similar. Regeneration of bone and connective tissue in the furcation defects was incomplete in most of the specimens. Statistically significant differences were not found in any of the evaluated parameters among the groups. Conclusion: Periodontal healing was similar using surgical debridement alone, AB graft, or AB graft with a CS barrier in the treatment of Class II furcation defects.

Screen-printed carbon electrode modified with poly-L-histidine applied to voltammetric determination of chromium (VI)

The present work reports the use of a screen-printed carbon electrode (SPCE) modified by poly-L-histidine film to determine chromium (VI). Stable films can be formed by direct addition of PH solution 1 % (w/v) on the electrode surface, followed by heating at 80°C during 5 min. Calibration curves can be constructed for Cr(VI) from 1.0 × 10-5 mol L-1 to 7.0 × 10-5 mol L-1 Cr (VI) in acetate buffer pH 4 using a preconcentration step of 60s at open circuit potential. A relative standard deviation of 3.2% was for five determination of 4.0 × 10 -5 mol L-1 Cr (VI). The method was successful applied to determination of Cr(VI) in wastewater samples from a leather dyeing industry. copyright The Electrochemical Society.