Dynamic estimation of three-dimensional cerebrovascular deformation from rotational angiography

Purpose: The objective of this study is to investigate the feasibility of detecting and quantifying 3D cerebrovascular wall motion from a single 3D rotational x-ray angiography (3DRA) acquisition within a clinically acceptable time and computing from the estimated motion field for the further biomechanical modeling of the cerebrovascular wall. Methods: The whole motion cycle of the cerebral vasculature is modeled using a 4D B-spline transformation, which is estimated from a 4D to 2D + t image registration framework. The registration is performed by optimizing a single similarity metric between the entire 2D + t measured projection sequence and the corresponding forward projections of the deformed volume at their exact time instants. The joint use of two acceleration strategies, together with their implementation on graphics processing units, is also proposed so as to reach computation times close to clinical requirements. For further characterizing vessel wall properties, an approximation of the wall thickness changes is obtained through a strain calculation. Results: Evaluation on in silico and in vitro pulsating phantom aneurysms demonstrated an accurate estimation of wall motion curves. In general, the error was below 10% of the maximum pulsation, even in the situation when substantial inhomogeneous intensity pattern was present. Experiments on in vivo data provided realistic aneurysm and vessel wall motion estimates, whereas in regions where motion was neither visible nor anatomically possible, no motion was detected. The use of the acceleration strategies enabled completing the estimation process for one entire cycle in 5-10 min without degrading the overall performance. The strain map extracted from our motion estimation provided a realistic deformation measure of the vessel wall. Conclusions: The authors' technique has demonstrated that it can provide accurate and robust 4D estimates of cerebrovascular wall motion within a clinically acceptable time, although it has to be applied to a larger patient population prior to possible wide application to routine endovascular procedures. In particular, for the first time, this feasibility study has shown that in vivo cerebrovascular motion can be obtained intraprocedurally from a 3DRA acquisition. Results have also shown the potential of performing strain analysis using this imaging modality, thus making possible for the future modeling of biomechanical properties of the vascular wall.

GESTÃO E AVALIAÇÃODE DESEMPENHO NA SHELL CABO VERDE, SARL

Cabo Verde foi alcandorado a PDM recentemente o que traz novos e grandes desafios para o seu processo de desenvolvimento. O país que tem as suas vulnerabilidades decorrentes do seu frágil tecido produtivo e da sua reduzida dimensão, para além da escassez de recursos naturais, enfrenta ainda o desafio da insularidade. Assim terá que ancorar-se em primeiro lugar nos seus recursos humanos, para enfrentar esses desafios. A questão da gestão de desempenho e recompensa começa a emergir-se no sector empresarial quer privado quer estatal, como um processo fundamental para se alcançar a excelência operacional, fundamental para enfrentar a competição nos dias de hoje. O presente estudo focou o sistema de avaliação de desempenho na Shell Cabo Verde uma filial do Grupo Shell, que é uma multinacional com uma história rica e com forte experiência no mercado Global. Procurou-se, através de um estudo de caso, fazer o levantamento e o enquadramento teórico do sistema e analisar até que ponto o mesmo tem potenciado a melhoria do desempenho organizacional através do alinhamento dos objectivos individuais e da organização. Cape Verde has recently been upgraded to a Medium Development Country condition which brings along new great challenges to its development process. The country has already its vulnerabilities due to its week productive tissue and its small dimension and beyond the lack of natural resources it has to deal with the challenge of insularity. Thus it has to anchor itself firstly in its human resources to face the challenges. The performance and reward management starts to emerge in both private’s and State’s entrepreneur sector, as a fundamental process to achieve the operational excellence in order to face the competitiveness now-a-days. This study focused the performance evaluation used in Shell Cape Verde, a company that belongs to the multinational Shell with a rich global market experience. We tried, through a case study, to understand the theoric contents of the system and analyze at what point it has enhanced the improvement of the organizational performance through the alignment of individual objectives and organizational objectives.

Relatório de Jogos de Marketing - Evolutec-Computer

A Evolutec-Computer é uma empresa especializada em engenharia eletrônica, que recebeu um financiamento de uma firma internacional de acionistas, que decidiu entrar no mercado de produção de microcomputador. Por conseguinte, foi criada uma nova divisão de PC Marketing para prosseguir nesta oportunidade de negócio. A fim de iniciar essa divisão, a Cooporate Headquarters forneceu o capital inicial (dinheiro do investimento). O montante concedido seria usado para abrir escritórios de vendas, design das marcas e realizar atividades de pesquisas R&D para as novas tecnologias. A nossa empresa recebeu 500.000 USD nos primeiros quatro semestres e 5.000.000 USD no quinto semestre, somando um total de 7.000.000 USD. A Evolutec-Computer terá o controlo da divisão de PC para os próximos dois anos (8 semestres/períodos de decisão). Dentro desse prazo, a Coorporate Headquarters espera ver a criação de uma divisão autossuficiente. A equipa criada pela Evolutec terá que ser capaz de gerar proveito das operações e contribuir para o lucro da corporação como um todo. Dentro dos 8 semestres, espera-se obter lucro suficiente para cobrir os investimentos iniciais...The Evolutec-Computer is a company specialized in electronic engineering, which has received funding from an international firm shareholder, who decided to enter the PC production market. Therefore, a new PC Marketing Division was created to pursue this business opportunity. In order to start this division, the Corporate Headquarters provided the initial capital (investment money). The sum would be used to open sales offices, design brands and carry out R & D research activities for new technologies. Our company received $ 500,000 in the first four semesters and $ 5,000,000 in the fifth semester, for a total of $ 7,000,000. The Evolutec-Computer will control the PC division for the next two years (eight semesters/decision periods). Within that period, the Coorporate Headquarters hopes to see the creation of a selfsufficient division. The team set up by Evolutec will have to be able to generate profit from operations and contribute to the profit of the corporation as a whole. Within 8 semesters, is expected to make enough profit to cover the initial investment. The performance of our company will be measured by Headquarter through the Balanced Scorecard, which will be based on financial performance, effectiveness of the marketing plan, market performance, investments in the company's future and wealth creation.

Field Demonstration and Laboratory Evaluation of Foamed Asphalts - Muscatine County, HR-233, 1985

In view of the energy, environmental, and economic advantages of the foamed asphalt process using local aggregates in cold mixes and the promising results from Research Project HR-212, a 4.2-mile section of county road in Muscatine County was built with foamed asphalt and local aggregates during August-September 1983. Extensive laboratory evaluation was carried out on five plant mixes representing foamed mixes used in the nine test sections, a laboratory prepared foamed mix, and a laboratory prepared hot mix similar to Plant Mix 1. The foamed mixes were compacted, cured under 15 curing conditions and tested for bulk specific gravity, Marshall stability at 77° F and at 140° F, cured moisture content, resilient modulus and effects of moisture damage due to freeze-thaw cycles, water soaking, and vacuum saturation. In addition, four sets of 83 core samples were taken at 1 to 15 months and tested for moisture content, specific gravity, Marshall stability, and resilient modulus. In summary, the test road has performed satisfactorily for almost two years. The few early construction problems encountered were to be expected for experimental projects dealing with new materials and technologies. Overall results to date are encouraging and foamed asphalt mixes have proved to have the potential as a viable base material in areas where marginal aggregates are available. It is hoped and expected that performance evaluation of the test sections will be continued and that more foamed asphalt trial projects will be constructed and monitored so that experiences and findings from this project can be verified and mix design criteria can be gradually established. For future foamed asphalt projects it is recommended that anti-stripping additives, such as hydrated lime, be added in view of the potential moisture susceptibility of foamed mixes observed in the laboratory evaluation.

Electronic Construction Collaboration System—Phase II, SPR RB02-008, 2010

During the first year of research, work was completed to identify Iowa DOT needs for web-based project management system (WPMS) and evaluate how commercially available solutions could meet these needs. Researchers also worked to pilot test custom developed WPMS solutions on Iowa DOT bridge projects. At the end of the first year of research, a Request for Proposals (RFP) was developed and issued by the Iowa DOT for the selection of a commercial WPMS to pilot test on multiple bridge projects. During the second year of research, the responses to the RFP issued during the first year of research were evaluated and a solution was selected. The selected solution, Attolist, was customized, tested, and implemented during the fall of 2009. Beginning in the winter of 2010, the solution was implemented on Iowa DOT projects. Researchers worked to assist in the training, implementation, and performance evaluation of the solution. Work will continue beyond the second year of research to implement Attolist on an additional pilot project. During this time, work will be completed to evaluate the impact of WPMS on Iowa DOT bridge projects.

Performance of Various Thicknesses of Portland Cement Concrete, HR-9, 30 Year Report, 1981

If adequately designed and high quality material and good construction practices are used, portland cement concrete is very durable. This is demonstrated by the oldest pavement in Iowa (second oldest in the U.S.) paved in 1904, which performed well for 70 years without resurfacing. The design thickness is an important factor in both the performance and cost of pavement. The objective of this paper is to provide a 30-year performance evaluation of a pavement constructed to determine the required design thickness for low volume secondary roadways. In 1951 Greene County and the Iowa Highway Research Board of the Iowa Department of Transportation initiated a four-mile (6.4 km) demonstration project to evaluate thicknesses ranging from 4-1/2" (11.4 cm) to 6" (15.2 cm). The project, consisting of 10 research sections, was formed pavement placed on a gravel roadbed with very little preparation except for redistribution of the loose aggregate. Eight sections were non-reinforced except for centerline tie bars and no contraction joints were used. Mesh reinforcing and contraction joints spaced at 29' 7" (9.02 m) intervals were used in two 4-1/2" (11.4 cm) thick sections. The only air entrained section was non-reinforced. The pavement performed well over its 30-year life carrying a light volume of traffic and did not require major maintenance. There was substantial cracking with average slab length varying directly with thickness. The 4-1/2" (11.4 cm) thick non-air entrained, mesh-reinforced pavement with contraction joints has performed the best.

Evaluation of Maturity and Pulse Velocity Measurements for PCC Traffic Opening Decisions, HR-380, 1998

Concrete paving is often at a disadvantage in terms of pavement type selection due to the time of curing required prior to opening the pavement to traffic. The State of Iowa has been able to reduce traffic delay constraints through material selection and construction methods to date. Methods for monitoring concrete strength gain and quality have not changed since the first concrete pavements were constructed in Iowa. In 1995, Lee County and the Iowa DOT cooperated in a research project, HR-380, to construct a 7.1 mile (11. 43 km) project to evaluate the use of maturity and pulse velocity nondestructive testing (NDT) methods in the estimation of concrete strength gain. The research identified the pros and cons of each method and suggested an instructional memorandum to utilize maturity measurements to meet traffic delay demands. Maturity was used to reduce the traffic delay opening time from 5-7 days to less than 2 days through the implementation of maturity measurements and special traffic control measures. Recommendations on the development of the maturity curve for each project and the location and monitoring of the maturity thermocouples are included. Examples of equipment that could easily be used by project personnel to estimate the concrete strength using the maturity methods is described.

Results of An International Study of Quantitative BCR/ABL Assays Using Defined RNA Samples

Molecular monitoring of BCR/ABL transcripts by real time quantitative reverse transcription PCR (qRT-PCR) is an essential technique for clinical management of patients with BCR/ABL-positive CML and ALL. Though quantitative BCR/ABL assays are performed in hundreds of laboratories worldwide, results among these laboratories cannot be reliably compared due to heterogeneity in test methods, data analysis, reporting, and lack of quantitative standards. Recent efforts towards standardization have been limited in scope. Aliquots of RNA were sent to clinical test centers worldwide in order to evaluate methods and reporting for e1a2, b2a2, and b3a2 transcript levels using their own qRT-PCR assays. Total RNA was isolated from tissue culture cells that expressed each of the different BCR/ABL transcripts. Serial log dilutions were prepared, ranging from 100 to 10-5, in RNA isolated from HL60 cells. Laboratories performed 5 independent qRT-PCR reactions for each sample type at each dilution. In addition, 15 qRT-PCR reactions of the 10-3 b3a2 RNA dilution were run to assess reproducibility within and between laboratories. Participants were asked to run the samples following their standard protocols and to report cycle threshold (Ct), quantitative values for BCR/ABL and housekeeping genes, and ratios of BCR/ABL to housekeeping genes for each sample RNA. Thirty-seven (n=37) participants have submitted qRT-PCR results for analysis (36, 37, and 34 labs generated data for b2a2, b3a2, and e1a2, respectively). The limit of detection for this study was defined as the lowest dilution that a Ct value could be detected for all 5 replicates. For b2a2, 15, 16, 4, and 1 lab(s) showed a limit of detection at the 10-5, 10-4, 10-3, and 10-2 dilutions, respectively. For b3a2, 20, 13, and 4 labs showed a limit of detection at the 10-5, 10-4, and 10-3 dilutions, respectively. For e1a2, 10, 21, 2, and 1 lab(s) showed a limit of detection at the 10-5, 10-4, 10-3, and 10-2 dilutions, respectively. Log %BCR/ABL ratio values provided a method for comparing results between the different laboratories for each BCR/ABL dilution series. Linear regression analysis revealed concordance among the majority of participant data over the 10-1 to 10-4 dilutions. The overall slope values showed comparable results among the majority of b2a2 (mean=0.939; median=0.9627; range (0.399 - 1.1872)), b3a2 (mean=0.925; median=0.922; range (0.625 - 1.140)), and e1a2 (mean=0.897; median=0.909; range (0.5174 - 1.138)) laboratory results (Fig. 1-3)). Thirty-four (n=34) out of the 37 laboratories reported Ct values for all 15 replicates and only those with a complete data set were included in the inter-lab calculations. Eleven laboratories either did not report their copy number data or used other reporting units such as nanograms or cell numbers; therefore, only 26 laboratories were included in the overall analysis of copy numbers. The median copy number was 348.4, with a range from 15.6 to 547,000 copies (approximately a 4.5 log difference); the median intra-lab %CV was 19.2% with a range from 4.2% to 82.6%. While our international performance evaluation using serially diluted RNA samples has reinforced the fact that heterogeneity exists among clinical laboratories, it has also demonstrated that performance within a laboratory is overall very consistent. Accordingly, the availability of defined BCR/ABL RNAs may facilitate the validation of all phases of quantitative BCR/ABL analysis and may be extremely useful as a tool for monitoring assay performance. Ongoing analyses of these materials, along with the development of additional control materials, may solidify consensus around their application in routine laboratory testing and possible integration in worldwide efforts to standardize quantitative BCR/ABL testing.

Release Process Effectiveness - Case of Operating Room Management Software

Työn päätavoitteena oli tuoda esiin tärkeimmät julkistamisprosessin tehokkuuteen vaikuttavat tekijät. Tutkimuksessa tarkasteltiin aihetta julkistamisprojektien vetäjän näkökulmasta. Kirjallinen selvitys kattaa keskeisimmät ohjelmistoprosessin, palvelun laadun sekä projektihallinnan teoriat. Kokeellisena aineistona käytettiin asiakkailta ja myynnin sekä käyttöönoton organisaatioilta tullutta palautetta ja asiantuntijahaastatteluita. Case-tuotteena tarkasteltiin suuren kansainvälisen yrityksen jälleenmyymää leikkaussalihallinnan ohjelmistoa. Tärkeimpiä julkistamisprosessin tehokkuuteen vaikuttavia tekijöitä ovat tiekartan ja julkistamispakettien sisällön hallinta, projektin aikataulujen pitäminen, rehellinen ja nopea kommunikaatio myyntikanavaan ja asiakkaille, sekä hyvin toteutettu testaus. Työssä käydään läpi esimerkkistrategioita kehittymiseen näillä alueilla.

Tietohallintoympäristön ylläpitopalveluiden laadun parantaminen ja suorituskyvyn mittaaminen

Suorituskyvyn mittaaminen korostuu yhä nopeammin muuttuvassa ja monimutkaisemmassa toimintaympäristössä. Taloudellisia mittareita laajempi suorituskyvyn mittaaminen mahdollistaa muutosten huomaamisen ja niihin reagoinnin aikaisemmin kuin pelkkä taloudellisten lukujen seuraaminen. Asiakkaiden vaatimuksien ja kilpailun kasvaessa tulee IT- yritysten pyrkiä yhä laadukkaampaan toimintaan pysyäkseen kilpailussa mukana. Tutkimuksen aiheena on rakentaa tasapainotettu mittaristo tietohallintoympäristön ylläpitopalveluille sekä esittää menetelmiä laadun parantamiseen. Palveluiden laadun parantamisen osalta käsitellään palvelun laadun ominaisuuksia, laadunhallintaa ja laadunhallintajärjestelmien käyttökokemuksia, kehitysmenetelmiä sekä laadun parantamisen vaikutuksia. Huomio kiinnittyi ennakoivaan laatutyöskentelyyn ja palvelun laadun ominaisuuksien monipuoliseen käsittelyyn. Palveluiden ollessa kyseessä painotus on toiminnanja suunnittelun laadussa. Suorituskyvyn mittaamisessa käsitellään suorituskyvynominaisuuksia, suorituskyvyn mittaamisen käyttöä, tasapainotettua mittaristoa ja mittariston rakentamista. Soveltavassa osiossa rakennetaan tasapainotettu mittaristo sekä esitetään menetelmiä palveluiden laadun parannukseen. Mittareiden valinnassa ja laadun kehittämisessä on käytetty hyväksi IT- yritysten viitekehyksiä ITILiä ja COBITia.

Varastonhallintakäytäntöjen kehittäminen maahantuontia harjoittavalle pienyritykselle

Työn tavoitteet liittyivät varastonhallintakäytäntöjen kehittämiseen sekä tämän seurantaan ja ylläpitoon liittyvien työvälineiden luomiseen. Päätutkimuskysymyksenä oli: 'Miten varastonhallintakäytäntöä kannattaisi parantaa, niin että nykyisillä resursseilla saavutettaisiin kustannussäästöjä asiakkaan palvelutasoa alentamatta?' Keskeinen teoreettinen sisältö liittyy varastonhallintakäytäntöihin. Tämä käsitellään varastonhallinnan perusteiden, varastonohjauksen, suorituskyvyn arvioinnin sekä varastonhallintakäytännön muutosprosessin avulla. Empiirinen osuus suoritetaan kohdeyrityksen logistisen muutosprosessimallin läpiviemisen avulla sisältäen tunnuslukuja, täydennysmenetelmiä, tuoteluokittelua ja muita analyyseja. Muutosprosessin vaiheet ovat edellytysten selvittäminen, nykytilan kuvaus ja analysointi, vaihtoehtoisten ratkaisujen ehdottaminen, nykytilan vertailu ratkaisuehdotelmiin, yhden ratkaisun valitseminen, muutoksen läpivienti ja lopputulosten seuranta. Työn keskeiset tulokset ovat erilaisten varastonhallintaan liittyvien tunnuslukujen laskeminen, tuoteluokittelun suorittaminen, täydennysmenetelmiin kuuluvien kaavojen luominen, varastokartan laatiminen ja toimintavaihtoehtojen esittely. Viimeiseen sisältyy oman muokatun kohdeyritykselle soveltuvan ¿voi tilata¿ täydennysmenetelmän laatiminen, ehdotuksen tekeminen liikkumattomien nimikkeiden eroon pääsemisestä, nimikkeiden uudelleensijoittaminen varastoon laaditun varastokartan mukaisesti, uuden työjaonluominen, muutosehdotuksen säännöllinen seuranta ja uusien tavoitteiden asettaminen sekä koulutustarpeeseen ja tietojärjestelmän kehittämiseen liittyvien ehdotusten tekeminen emoyhtiölle.

Asiakasorientaatio taloushallinnossa - Innovaation leviäminen Suomessa

Tutkielman tavoitteena oli selvittää taloushallinnon asiakasorientaation tilanne Suomessa. Asiakasorientaatio taloushallinnossa ymmärretään asiakaskannattavuuslaskentana, joka on osa asiakkuuden johtamista. Asiakaskannattavuuslaskentaa tutkittiin innovaationa ja tutkimusongelmana selvitettiin miten ja minkä tekijöiden vaikutuksesta diffuusio on tapahtunut Suomessa ajanjaksolla 1995-2006. Alatutkimusongelmina tutkittiin innovaation omaksuneiden yritysten erityispiirteitä sekä syitä innovaation hitaaseen diffuusioon. Tutkielma toteutettiin tapaustutkimuksena. Aineisto koottiin talouslehtien antamien viitteiden sekä aiheesta teetettyjen diplomitöiden ja pro gradujen case-osuuksien pohjalta. Tutkielman empiria-osiota on analysoitu sekä kvalitatiivisesti että kvantitatiivisesti, painoarvon ollessa kvalitatiivisessa tekniikassa. Asiakaskannattavuuslaskenta on levinnyt Suomeen konsultointiyritysten, yliopistojen ja median välityksellä. Innovaation leviämiseen ovat osaltaan vaikuttanut tasapainoitetun mittariston ja CRM:n levimäinen. Tärkeimpiä motiiveja ja syitä yritysten haluun omaksua innovaatio ovat kiristyvä kilpailu, tietojärjestelmien kehittyminen ja vanhan laskentajärjestelmän informatiivisyyden riittämättömyys. Syitä hitaaseen diffuusion puolestaan löytyi 1990-luvun lopun kehittymättömistä tietojärjestelmistä, markkinoinnin ja taloushallinnon erilaisista näkökannoista sekä resurssien puutteesta.

Balanced scorecardin rakentaminen caseyritykselle

Tutkielman teoriaosuuden tavoitteena on selvittää kuinka Balanced scorecard -malli rakentuu ja toimii. Caseosuuden tavoitteena on määritellä esimerkkiyritykselle sopiva tasapainotettu mittaristo ottaen huomioon yrityksen toimiala ja toimintaympäristön sekä toimintaympäristön muutostrendit. Lisäksi tutkimuksen tavoitteena on antaa esimerkkiyritykselle toimintaohjeet heidän Balanced scorecard -projektin loppuunviemiseksi. Toiminnanohjausmalleista syvällisimmin käsitellään Kaplanin jaNortonin Balanced scorecard -mallia, josta käytetään myös nimitystä tasapainotettu mit-taristo. Tutkimus perustuu laajaan kirjallisuuskatsaukseen aihepiiristä sekä esimerkkiyrityksen avainhenkilöiden haastatteluihin ja caseyrityksen kirjallisiin dokumentteihin. Kaplanin ja Nortonin julkaisut ovat toimineet teoriaosuuden runkoaineistona varsinkin Balanced scorecardia käsittelevien osioiden osalta. Myös Olven ym. sekä Toivasen tutkimukset Balanced scorecardin käyttöönotossa ovat merkittävässä osassa teoriaosuudessa. En työskentele yrityksessä, vaanteen tutkimukseni ulkopuolisena tutkijana.

Web Presence Building and Performance Measuring in Business-to-Business Markets

Tutkimuksen tavoite oli selvittää yrityksen web toiminnan rakentamisen vaiheita sekä menestyksen mittaamista. Rakennusprosessia tutkittiin viisiportaisen askelmallin avulla. Mallin askeleet ovat; arviointi, strategian muotoilu, suunnitelma, pohjapiirros ja toteutus. Arviointi- ja toteutusvaiheiden täydentämiseksi sekä erityisesti myös internet toiminnan onnistumisen mittaamisen avuksi internet toiminnan hyödyt (CRM,kommunikointi-, myynti-, ja jakelukanava hyödyt markkinoinnin kannalta) käsiteltiin. Toiminnan menestyksen arvioinnin avuksi esiteltiin myös porrasmalli internet toimintaan. Porrasmalli määrittelee kauppakulissi-, dynaaminen-, transaktio- ja e-businessportaat. Tutkimuksessa löydettiin menestystekijöitä internet toimintojen menestykselle. Nämä tekijät ovat laadukas sisältö, kiinnostavuus, viihdyttävyys, informatiivisuus, ajankohtaisuus, personoitavuus, luottamus, interaktiivisuus, käytettävyys, kätevyys, lojaalisuus, suoriutuminen, responssiivisuus ja käyttäjätiedon kerääminen. Mittarit jaettiin tutkimuksessa aktiivisuus-, käyttäytymis- ja muunnosmittareihin. Lisäksi muita mittareita ja menestysindikaattoreita esiteltiin. Nämä menestyksen elementit ja mittarit koottiin yhteen uudessa internet toimintojen menestyksenarviointimallissa. Tutkielman empiirisessä osuudessa,esitettyjä teorioita peilattiin ABB:n (ABB:n sisällä erityisesti ABB Stotz-Kontakt) web toimintaan. Apuna olivat dokumenttianalyysi sekä haastattelut. Empiirinen osa havainnollisti teoriat käytännössä ja toi ilmi mahdollisuuden teorioiden laajentamiseen. Internet toimintojen rakentamismallia voidaan käyttää myös web toimintojen kehittämiseen ja porrasmalli sopii myös nykyisten internet toimintojen arvioimiseen. Mittareiden soveltaminen käytännössä toi kuitenkin ilmi tarpeen niiden kehittämiseen ja aiheen lisätutkimukseen. Niiden tulisi olla myös aiempaatiiviimmin liitetty kokonaisvaltaisen liiketoiminnan menestyksen mittaamiseen.