Processo de fabricação de tarugos pelo método HotTop de ligas de alumínio da série 6XXX e as não conformidades desse processamento

The goal of this work is to report some problems that occur in the in the production of aluminum billets (series 6XXX) produced by the hot top process in the Alcoa aluminum Inc. The aluminum fabrication process is described from its first stage, since the mining until the reduction, smelting and treatment of the metal. One of the plant’s final product, are billets for clients that produce profiles by extrusion. The product’s final quality highly depends on the whole production process. Therefore it’s necessary to use good practices in the treatment of the metal, follow up its fabrication and control its thermal treatment, in order to meet the required standards to satisfy the clients. The billet’s production method and its variables will be detailed through temperature and casting speed, cone of water flow, cooling rate, duration of thermal treatment, degassing and metal “in line “filtering, in other words when it’s still found in its liquid state. The non-conformities of the process were studied by metallographic analysis, both macrostutural and microstructural that will be described and discussed in this work

Modeling hydrothermal system: deriving observables and hydrothermal instability in volcanic and non-volcanic setting

Hydrothermal fluids are a fundamental resource for understanding and monitoring volcanic and non-volcanic systems. This thesis is focused on the study of hydrothermal system through numerical modeling with the geothermal simulator TOUGH2. Several simulations are presented, and geophysical and geochemical observables, arising from fluids circulation, are analyzed in detail throughout the thesis. In a volcanic setting, fluids feeding fumaroles and hot spring may play a key role in the hazard evaluation. The evolution of the fluids circulation is caused by a strong interaction between magmatic and hydrothermal systems. A simultaneous analysis of different geophysical and geochemical observables is a sound approach for interpreting monitored data and to infer a consistent conceptual model. Analyzed observables are ground displacement, gravity changes, electrical conductivity, amount, composition and temperature of the emitted gases at surface, and extent of degassing area. Results highlight the different temporal response of the considered observables, as well as the different radial pattern of variation. However, magnitude, temporal response and radial pattern of these signals depend not only on the evolution of fluid circulation, but a main role is played by the considered rock properties. Numerical simulations highlight differences that arise from the assumption of different permeabilities, for both homogeneous and heterogeneous systems. Rock properties affect hydrothermal fluid circulation, controlling both the range of variation and the temporal evolution of the observable signals. Low temperature fumaroles and low discharge rate may be affected by atmospheric conditions. Detailed parametric simulations were performed, aimed to understand the effects of system properties, such as permeability and gas reservoir overpressure, on diffuse degassing when air temperature and barometric pressure changes are applied to the ground surface. Hydrothermal circulation, however, is not only a characteristic of volcanic system. Hot fluids may be involved in several mankind problems, such as studies on geothermal engineering, nuclear waste propagation in porous medium, and Geological Carbon Sequestration (GCS). The current concept for large-scale GCS is the direct injection of supercritical carbon dioxide into deep geological formations which typically contain brine. Upward displacement of such brine from deep reservoirs driven by pressure increases resulting from carbon dioxide injection may occur through abandoned wells, permeable faults or permeable channels. Brine intrusion into aquifers may degrade groundwater resources. Numerical results show that pressure rise drives dense water up to the conduits, and does not necessarily result in continuous flow. Rather, overpressure leads to new hydrostatic equilibrium if fluids are initially density stratified. If warm and salty fluid does not cool passing through the conduit, an oscillatory solution is then possible. Parameter studies delineate steady-state (static) and oscillatory solutions.

Continuous geochemical monitoring by mass-spectometer in the Campi Flegrei geothermal area. An application at Pisciarelli-Solfatara (diffuse and fumarolic gases) and at the mud gases during drilling of the CFDDP pilot hole

During this work has been developed an innovative methodology for continuous and in situ gas monitoring (24/24 h) of fumarolic and soil diffusive emissions applied to the geothermal and volcanic area of Pisciarelli near Agnano inside the Campi Flegrei caldera (CFc). In literature there are only scattered and in discrete data of the geochemical gas composition of fumarole at Campi Flegrei; it is only since the early ’80 that exist a systematic record of fumaroles with discrete sampling at Solfatara (Bocca Grande and Bocca Nuova fumaroles) and since 1999, even at the degassing areas of Pisciarelli. This type of sampling has resulted in a time series of geochemical analysis with discontinuous periods of time set (in average 2-3 measurements per month) completely inadequate for the purposes of Civil Defence in such high volcanic risk and densely populated areas. For this purpose, and to remedy this lack of data, during this study was introduced a new methodology of continuous and in situ sampling able to continuously detect data related and from its soil diffusive degassing. Due to its high sampling density (about one measurement per minute therefore producing 1440 data daily) and numerous species detected (CO2, Ar, 36Ar, CH4, He, H2S, N2, O2) allowing a good statistic record and the reconstruction of the gas composition evolution of the investigated area. This methodology is based on continuous sampling of fumaroles gases and soil degassing using an extraction line, which after undergoing a series of condensation processes of the water vapour content - better described hereinafter - is analyzed through using a quadrupole mass spectrometer

Photochemie der Troposphäre in niedrigen und mittleren Breiten: Die Rolle von Konvektion

Ozon (O3) ist in der Atmosphäre ein wichtiges Oxidanz und Treibhausgas. Während die höchsten Konzentrationen in der Stratosphäre beobachtet werden und die vor der gefährlichen UV-Strahlung schützende Ozonschicht bilden, können sich signifikante Änderungen der Ozon-Konzentration in der Region der Tropopause auf das Klima der Erde auswirken. Des Weiteren ist Ozon eine der Hauptquellen für das Hydroxylradikal (OH) und nimmt damit entscheidend Einfluss auf die Oxidationskraft der Atmosphäre. Der konvektive Transport von Ozon und seinen Vorläufergasen aus Regionen nahe der Erdoberfläche in die freie Troposphäre beeinflusst das Budget dieser Spezies in der Tropopausenregion.rnDie Datengrundlage der Studie in der vorliegenden Arbeit basiert auf den flugzeuggetragenen Messkampagnen GABRIEL 2005 (Suriname, Südamerika) sowie HOOVER I 2006 und HOOVER II 2007 (beide in Europa). Mit dem zur Verfügung stehenden Datensatz wird das Ozonbudget in der freien, unbelasteten Hintergrundatmosphäre und in der durch hochreichende Konvektion gestörten, oberen Troposphäre untersucht. Anhand der auf in-situ Messungen von O3, NO, OH, HO2 und dem aktinischen Strahlungsfluss basierten Berechnung der Netto-Ozonproduktionsrate (NOPR) werden für das Messgebiet Ozontendenzen in der unbelasteten Troposphäre abgeleitet und mit Simulationen des globalen Chemie-Transport-Modells MATCH-MPIC verglichen. Mit Hilfe zweier Fallstudien in den Tropen in Südamerika und den mittleren Breiten in Europa werden die Auswirkungen von hochreichender Konvektion auf die obere Troposphäre quantifiziert.rnDie Ergebnisse zeigen für die Grenzschicht in niedrigen und mittleren Breiten eine eindeutige Tendenz zur Produktion von Ozon, was für den tropischen Regenwald in der Messregion nicht der allgemeinen Erwartung entsprach, nach der diese Region durch die Zerstörung von Ozon charakterisiert sein sollte. In der oberen Troposphäre ab etwa 7 km wird für die beiden Regionen eine leichte Tendenz zur Ozonproduktion beobachtet. Signifikante Unterschiede zeigen die Ergebnisse für die mittlere Troposphäre. Während die Tropen in dieser Region durch eine eindeutige Tendenz zur Zerstörung von Ozon charakterisiert sind, lässt sich über den mittleren Breiten zwar eine hohe photochemische Aktivität aber keine derart klare Tendenz feststellen. Die hohen Breiten zeichnen sich durch eine neutrale Troposphäre in Bezug auf die Ozontendenz aus und weisen kaum photochemische Aktivität auf. Der Vergleich dieser Ergebnisse mit dem MATCH-MPIC Modell zeigt in weiten Teilen der Messregionen eine grundlegende Übereinstimmung in der Tendenz zur Produktion oder Zerstörung von Ozon. Die absoluten Werte werden vom Modell aber generell unterschätzt. Signifikante Unterschiede zwischen in-situ Daten und Modellsimulationen werden in der Grenzschicht über dem tropischen Regenwald identifiziert.rnDer Einfluss der Konvektion ist durch eine signifikant erhöhte NOPR gekennzeichnet. In dieser Arbeit wird in den Tropen mit einem Median-Wert von 0.20 ppbv h−1 eine um den Faktor 3.6 erhöhte NOPR im Vergleich zur ungestörten oberen Troposphäre abgeschätzt. In den mittleren Breiten führt die um eine Größenordnung höhere NO-Konzentration zu einem Wert von 1.89 ppbv h−1, was einer Überhöhung um einen Faktor 6.5 im Vergleich zum ungestörten Zustand entspricht. Diese Ergebnisse zeigen für beide Regionen in der oberen Troposphäre eine erhöhte Ozonproduktion als Folge konvektiver Aktivität. rnrnHochreichende Konvektion ist zudem ein sehr effektiver Mechanismus für den Vertikaltransport aus der Grenzschicht in die obere Troposphäre. Die schnelle Hebung in konvektiven Wolken führt bei Spurengasen mit Quellen an der Erdoberfläche zu einer Erhöhung ihrer Konzentration in der oberen Troposphäre. Die hochgradig löslichen Spurenstoffe Formaldehyd (HCHO) und Wasserstoffperoxid (H2O2) sind wichtige Vorläufergase der HOx-Radikale. Es wird angenommen, dass sie aufgrund ihrer Löslichkeit in Gewitterwolken effektiv ausgewaschen werden.rnIn der vorliegenden Arbeit wird eine Fallstudie von hochreichender Konvektion im Rahmen des HOOVER II Projekts im Sommer 2007 analysiert. Am 19.07.2007 entwickelten sich am Nachmittag am Südostrand eines in nordöstlicher Richtung ziehenden mesoskaligen konvektiven Systems drei zunächst isolierte konvektive Zellen. Flugzeuggetragene Messungen in der Aus- und der Einströmregion einer dieser Gewitterzellen stellen einen exzellenten Datensatz bereit, um die Auswirkungen von hochreichender Konvektion auf die Verteilung verschiedener Spurengase in der oberen Troposphäre zu untersuchen. Der Vergleich der Konzentrationen von Kohlenstoffmonoxid (CO) und Methan (CH4) zwischen der oberen Troposphäre und der Grenzschicht deutet auf einen nahezu unverdünnten Transport dieser langlebigen Spezies in der konvektiven Zelle hin. Die Verhältnisse betragen (0.94±0.04) für CO und (0.99±0.01) für CH4. Für die löslichen Spezies HCHO und H2O2 beträgt dieses Verhältnis in der Ausströmregion (0.55±0.09) bzw. (0.61±0.08). Dies ist ein Indiz dafür, dass diese Spezies nicht so effektiv ausgewaschen werden wie angenommen. Zum besseren Verständnis des Einflusses der Konvektion auf die Budgets dieser Spezies in der oberen Troposphäre wurden im Rahmen dieser Arbeit Boxmodell-Studien für den Beitrag der photochemischen Produktion in der Ausströmregion durchgeführt, wobei die gemessenen Spezies und Photolysefrequenzen als Randbedingungen dienten. Aus den Budgetbetrachtungen für HCHO und H2O2 wird eine Auswascheffizienz von (67±24) % für HCHO und (41±18) % für H2O2 abgeschätzt. Das für H2O2 überraschende Ergebnis lässt darauf schließen, dass dieses Molekül in einer Gewitterwolke deutlich effektiver transportiert werden kann, als aufgrund seiner hohen Löslichkeit aus der Henry-Konstanten zu erwarten wäre. Das Ausgasen von gelöstem H2O2 beim Gefrieren eines Wolkentropfens, d.h. ein Retentionskoeffizient kleiner 1, ist ein möglicher Mechanismus, der zum beobachteten Mischungsverhältnis dieser löslichen Spezies in der Ausströmregion beitragen kann.

Roman aqueducts and calcareous sinter deposits as a proxy for environmental changes

Die im Süden der Türkei gelegen, antiken Städte Aspendos und Patara, waren in der Römerzeit zwei bedeutende Handelszentren mit hoher Bevölkerungsdichte. Aquädukte versorgten beide Städte mit carbonathaltigem Wasser, wobei sich Kalksinter (Calciumcarbonat) in der Kanalrinne ablagerte. Dabei lagern sich im Wechsel eine hellere und dunklere Kalksinterlage ab, die als Sinterpaar bezeichnet wird. Um die Entstehung dieser Sinterpaare besser zu verstehen, und die beteiligten Prozesse mit saisonalen Veränderungen der Umwelt zu korrelieren, werden in der vorliegenden Arbeit laminierten Sinterablagerungen mit geochemischen und petrographischen Methoden untersucht.rnEntlang der Kanalrinne beider Aquädukte wurden an mehreren Stellen Proben entnommen. Es wurde untersucht in wieweit sich die Sinterstruktur aufgrund von Änderungen in der Neigung des Wasserkanals oder des Kanaltyps ändert. Um die Kristallform und die kristallografische Orientierung der Kristalle innerhalb der verschiedenen Sinterpaare zu untersuchen, wurden die entnommenen laminierten Kalksinterablagerungen mit Hilfe optischer Mikroskopie und EBSD (Electron Backscatter Diffraction) analysiert. Der Electron Probe Micro-Analyzer (EPMA) wurde verwendet, um saisonale Schwankungen der Hauptelementverteilung und den Anteil der stabilen Isotope im Wasser zu bestimmen. Die LA-ICP-MS (Laser Ablation-induktiv gekoppeltem Plasma-Massenspektrometrie) Spurenelementanalyse wurde durchgeführt, um kleinste Schwankungen der Spurenelemente zu finden. Basierend auf diesen Analysen wurde festgestellt, dass laminierten Kalksinterablagerungen laterale Änderungen in der Aquäduktstruktur und -neigung, jahreszeitliche Änderungen der Wasserchemie, der Temperatur sowie der Entgasungsrate während eines Jahres widerspiegeln. Die Kalksinterablagerungen zeigen eine deutliche Laminierung in Form von feinkörnig-porösen und grobkörnig-dichten Schichten, die trockene und nasse Jahreszeiten anzeigen. Feinkörnige Schichten zeigen eine hohe Epifluoreszenz aufgrund reichhaltiger organischer Inhalte, die vermutlich eine Folge der bakteriellen Aktivität während der warmen und trockenen Jahreszeit sind. Stabile Sauerstoff und Kohlenstoff-Isotop-Kurven entsprechen auch den jahreszeitlichen Schwankungen der verschiedenen Schichtenpaare. Vor allem δ 18O spiegelt jährliche Veränderungen in der Temperatur und jahreszeitliche Veränderungen des Abflusses wieder. Das wichtigste Ergebnis ist, dass die Periodizität von δ 18O durch Erwärmen des Wassers im Wasserkanal und nicht durch die Verdunstung oder der Brunnenwasser-Charakteristik verursacht wird. Die Periodizität von δ 13C ist komplexer Natur, vor allem zeigen δ 18O und δ 13C eine Antikorrelation entlang der Lamellenpaare. Dies wird wohl vor allem durch Entgasungsprozesse im Aquädukt verursacht. Die Ergebnisse der Spurenelemente sind meist inkonsistent und zeigen keine signifikanten Veränderungen in den verschiedenen Lamellenpaaren. Die Isotope Mg, Sr und Ba zeigen hingegen bei einigen Proben eine positive Korrelation und erreichen Höchstwerte innerhalb feinkörnig-poröser Schichten. Auch sind die Hauptelementwerte von Fe, K, Si und anderer detritischer Elemente innerhalb der feinkörnige-porösen Schichten maximal. Eine genaue Datierung der Kalksinterablagerungen ist wünschenswert, da der Zeitraum, in dem die Aquädukte aktiv waren, bereits archäologisch auf 200-300 Jahre festgelegt wurde. Paläomagnetische und 14C-Datierung geben keine brauchbare Ergebnisse. Die U/Th Isotopie wird durch eine hohe Anfangskonzentration von Th in den Proben behindert. Trotz dieser Schwierigkeiten war eine U/Th Datierung an einem Testbeispiel des Béziers Aquädukt erfolgreich. Mit Hilfe von analogen Untersuchungen an aktiven Wasserkanälen der heutigen Zeit, werden die Ablagerungsmechanismen und die geochemische Entwicklung der laminierten Sinterschichten besser verstanden. Ein weiteres laufendes Projekt dieser Doktorarbeit ist die Überwachung von Sinterabscheidungen und der saisonale Zusammensetzung des Wassers an einigen heute noch aktiven Aquädukten. Das Ziel ist die Untersuchung der jetzigen Calciumcarbonatabscheidungen in Aquäduktkanälen unter den heutigen Umgebungsbedingungen. Erste Ergebnisse zeigen, dass kleine regelmäßige jahreszeitliche Veränderungen in der Isotopenzusammensetzung des Wassers vorliegen, und dass die beobachtete Periodizität der stabilen Isotope aufgrund von Änderungen im eigentlichen Kanal entstanden ist. Die Untersuchung von Kalksinterablagerungen in römischen Aquädukten liefern vielversprechende Ergebnisse, für die Untersuchung des Paläöklimas, der Archaeoseismologie und anderer Umweltbedingungen in der Römerzeit. Diese Studie beschränkt sich auf zwei Aquädukte. Die Untersuchungen weiterer Aquädukte und einer Überwachung, der noch in Betrieb stehenden Aquädukte werden genauere Ergebnisse liefern.

Analisi del degassamento di CO2 diffuso dal suolo presso la Solfatara di Pozzuoli (Napoli, Italia): Misura, mapping e quantificazione del flusso totale.

Il presente lavoro ha come obiettivo la descrizione dello studio del degassamento diffuso di CO2 (acquisizione dei dati e loro trattazione) effettuato nell'area vulcanica dei Campi Flegrei (NA), nello specifico nell'area della Solfatara di Pozzuoli. Questo infatti rappresenta attualmente il punto di massimo rilascio di fluidi ed energia dell'intero Distretto Vulcanico Flegreo attraverso attività quali fumarole e degassamento diffuso dal suolo, nonché deformazioni del terreno (bradisismo). Tramite l'acquisizione dei valori di flusso diffuso e delle temperature dei primi 10 cm di suolo, attraverso una trattazione dei dati statistica e geostatistica, è stato possibile distinguere e caratterizzare le sorgenti di CO2 (biologica o vulcanica), la realizzazione di sviluppo di mappe di probabilità e di flusso medio e la quantificazione dell'output totale giornaliero di CO2. Il lavoro è stato suddiviso in due fasi principali: 1. La prima fase ha riguardato l'acquisizione dei dati sul campo nei giorni 19 e 20 marzo 2015, tramite l'utilizzo di una camera d'accumulo ed un termometro munito di sonda, in 434 punti all'interno del cratere della Solfatara e nelle aree circostanti. 2. Nella seconda fase sono stati elaborati i dati, utilizzando il metodo statistico GSA (Graphical Statistic Approach) ed il metodo geostatistico della simulazione sequenziale Gaussiana (sGs). Tramite il GSA è stato possibile ripartire i dati in popolazioni e definire una media (con relativa varianza) per ognuna di esse. Con la sGs è stato possibile trattare i dati, considerando la loro distribuzione spaziale, per simulare valori per le aree prive di misurazioni; ciò ha permesso di generare delle mappe che mostrassero l'andamento dei flussi e la geometria della struttura del degassamento diffuso (Diffuse Degassing Structure, DDS; Chiodini et al., 2001). Infine i dati ottenuti sono stati confrontati con i risultati di precedenti studi e si è messo in relazione la geometria e l'intensità di degassamento con la geologia strutturale dell'area flegrea indagata.

Geochemical Modeling and Analysis of the Frac Water Used in the Hydraulic Fracturing of the Marcellus Formation, Pennsylvania

The hydraulic fracturing of the Marcellus Formation creates a byproduct known as frac water. Five frac water samples were collected in Bradford County, PA. Inorganic chemical analysis, field parameters analysis, alkalinity titrations, total dissolved solids(TDS), total suspended solids (TSS), biological oxygen demand (BOD), and chemical oxygen demand (COD) were conducted on each sample to characterize frac water. A database of frac water chemistry results from across the state of Pennsylvania from multiple sources was compiled in order to provide the public and research communitywith an accurate characterization of frac water. Four geochemical models were created to model the reactions between frac water and the Marcellus Formation, Purcell Limestone, and the oil field brines presumed present in the formations. The average concentrations of chloride and TDS in the five frac water samples were 1.1 �± 0.5 x 105 mg/L (5.5X average seawater) and 140,000 mg/L (4X average seawater). BOD values for frac water immediately upon flow back were over 10X greater than the BOD of typical wastewater, but decreased into the range of typical wastewater after a short period of time. The COD of frac water decreases dramatically with an increase in elapsed time from flow back, but remain considerably higher than typicalwastewater. Different alkalinity calculation methods produced a range of alkalinity values for frac water: this result is most likely due to high concentrations of aliphatic acid anions present in the samples. Laboratory analyses indicate that the frac watercomposition is quite variable depending on the companies from which the water was collected, the geology of the local area, and number of fracturing jobs in which the frac water was used, but will require more treatment than typical wastewater regardless of theprecise composition of each sample. The geochemical models created suggest that the presence of organic complexes in an oil field brine and Marcellus Formation aid in the dissolution of ions such as bariumand strontium into the solution. Although equilibration reactions between the Marcellus Formation and the slickwater account for some of the final frac water composition, the predominant control of frac water composition appears to be the ratio of the mixture between the oil field brine and slickwater. The high concentration of barium in the frac water is likely due to the abundance of barite nodules in the Purcell Limestone, and the lack of sulfate in the frac water samples is due to the reducing, anoxic conditions in the earth's subsurface that allow for the degassing of H2S(g).

Dynamics and kinematics of eruptive activity at Fuego volcano, Guatemala 2005-2009

Volcanoes are the surficial expressions of complex pathways that vent magma and gasses generated deep in the Earth. Geophysical data record at least the partial history of magma and gas movement in the conduit and venting to the atmosphere. This work focuses on developing a more comprehensive understanding of explosive degassing at Fuego volcano, Guatemala through observations and analysis of geophysical data collected in 2005 – 2009. A pattern of eruptive activity was observed during 2005 – 2007 and quantified with seismic and infrasound, satellite thermal and gas measurements, and lava flow lengths. Eruptive styles are related to variable magma flux and accumulation of gas. Explosive degassing was recorded on broadband seismic and infrasound sensors in 2008 and 2009. Explosion energy partitioning between the ground and the atmosphere shows an increase in acoustic energy from 2008 to 2009, indicating a shift toward increased gas pressure in the conduit. Very-long-period (VLP) seismic signals are associated with the strongest explosions recorded in 2009 and waveform modeling in the 10 – 30 s band produces a best-fit source location 300 m west and 300 m below the summit crater. The calculated moment tensor indicates a volumetric source, which is modeled as a dike feeding a SW-dipping (35°) sill. The sill is the dominant component and its projection to the surface nearly intersects the summit crater. The deformation history of the sill is interpreted as: 1) an initial inflation due to pressurization, followed by 2) a rapid deflation as overpressure is explosively release, and finally 3) a reinflation as fresh magma flows into the sill and degasses. Tilt signals are derived from the horizontal components of the seismometer and show repetitive inflation deflation cycles with a 20 minute period coincident with strong explosions. These cycles represent the pressurization of the shallow conduit and explosive venting of overpressure that develops beneath a partially crystallized plug of magma. The energy released during the strong explosions has allowed for imaging of Fuego’s shallow conduit, which appears to have migrated west of the summit crater. In summary, Fuego is becoming more gas charged and its summit centered vent is shifting to the west - serious hazard consequences are likely.

Comparisons between OMI SO2 data and ground-based SO2 measurements at Turrialba volcano

Turrialba is one of the largest and most active stratovolcanoes in the Central Cordillera of Costa Rica and an excellent target for validation of satellite data using ground based measurements due to its high elevation, relative ease of access, and persistent elevated SO2 degassing. The Ozone Monitoring Instrument (OMI) aboard the Aura satellite makes daily global observations of atmospheric trace gases and it is used in this investigation to obtain volcanic SO2 retrievals in the Turrialba volcanic plume. We present and evaluate the relative accuracy of two OMI SO2 data analysis procedures, the automatic Band Residual Index (BRI) technique and the manual Normalized Cloud-mass (NCM) method. We find a linear correlation and good quantitative agreement between SO2 burdens derived from the BRI and NCM techniques, with an improved correlation when wet season data are excluded. We also present the first comparisons between volcanic SO2 emission rates obtained from ground-based mini-DOAS measurements at Turrialba and three new OMI SO2 data analysis techniques: the MODIS smoke estimation, OMI SO2 lifetime, and OMI SO2 transect techniques. A robust validation of OMI SO2 retrievals was made, with both qualitative and quantitative agreements under specific atmospheric conditions, proving the utility of satellite measurements for estimating accurate SO2 emission rates and monitoring passively degassing volcanoes.

Ultraviolet digital imaging of volcanic plumes : implementation and application to magmatic processes at basaltic volcanoes

Magmatic volatiles play a crucial role in volcanism, from magma production at depth to generation of seismic phenomena to control of eruption style. Accordingly, many models of volcano dynamics rely heavily on behavior of such volatiles. Yet measurements of emission rates of volcanic gases have historically been limited, which has restricted model verification to processes on the order of days or longer. UV cameras are a recent advancement in the field of remote sensing of volcanic SO2 emissions. They offer enhanced temporal and spatial resolution over previous measurement techniques, but need development before they can be widely adopted and achieve the promise of integration with other geophysical datasets. Large datasets require a means by which to quickly and efficiently use imagery to calculate emission rates. We present a suite of programs designed to semi-automatically determine emission rates of SO2 from series of UV images. Extraction of high temporal resolution SO2 emission rates via this software facilitates comparison of gas data to geophysical data for the purposes of evaluating models of volcanic activity and has already proven useful at several volcanoes. Integrated UV camera and seismic measurements recorded in January 2009 at Fuego volcano, Guatemala, provide new insight into the system’s shallow conduit processes. High temporal resolution SO2 data reveal patterns of SO2 emission rate relative to explosions and seismic tremor that indicate tremor and degassing share a common source process. Progressive decreases in emission rate appear to represent inhibition of gas loss from magma as a result of rheological stiffening in the upper conduit. Measurements of emission rate from two closely-spaced vents, made possible by the high spatial resolution of the camera, help constrain this model. UV camera measurements at Kilauea volcano, Hawaii, in May of 2010 captured two occurrences of lava filling and draining within the summit vent. Accompanying high lava stands were diminished SO2 emission rates, decreased seismic and infrasonic tremor, minor deflation, and slowed lava lake surface velocity. Incorporation of UV camera data into the multi-parameter dataset gives credence to the likelihood of shallow gas accumulation as the cause of such events.

Remote sensing of volcanic plumes using the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER).

The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) has been used to quantify SO2 emissions from passively degassing volcanoes. This dissertation explores ASTER’s capability to detect SO2 with satellite validation, enhancement techniques and extensive processing of images at a variety of volcanoes. ASTER is compared to the Mini UV Spectrometer (MUSe), a ground based instrument, to determine if reasonable SO2 fluxes can be quantified from a plume emitted from Lascar, Chile. The two sensors were in good agreement with ASTER proving to be a reliable detector of SO2. ASTER illustrated the advantages of imaging a plume in 2D, with better temporal resolution than the MUSe. SO2 plumes in ASTER imagery are not always discernible in the raw TIR data. Principal Component Analysis (PCA) and Decorrelation Stretch (DCS) enhancement techniques were compared to determine how well they highlight a variety of volcanic plumes. DCS produced a consistent output and the composition of the plumes was easy to identify from explosive eruptions. As the plumes became smaller and lower in altitude they became harder to distinguish using DCS. PCA proved to be better at identifying smaller low altitude plumes. ASTER was used to investigate SO2 emissions at Lascar, Chile. Activity at Lascar has been characterized by cyclic behavior and persistent degassing (Matthews et al. 1997). Previous studies at Lascar have primarily focused on changes in thermal infrared anomalies, neglecting gas emissions. Using the SO2 data along with changes in thermal anomalies and visual observations it is evident that Lascar is at the end an eruptive cycle that began in 1993. Declining gas emissions and crater temperatures suggest that the conduit is sealing. ASTER and the Ozone Monitoring Instrument (OMI) were used to determine the annual contribution of SO2 to the troposphere from the Central and South American volcanic arcs between 2000 and 2011. Fluxes of 3.4 Tg/a for Central America and 3.7 Tg/a for South America were calculated. The detection limits of ASTER were explored. The results a proved to be interesting, with plumes from many of the high emitting volcanoes, such as Villarrica, Chile, not being detected by ASTER.

SO2 emissions at Volcan de Colima, 2003-2007

Volcán de Colima has been continuously erupting since the onset of dome growth in 1998. This period of unrest has had 4 prominent periods; 1998-1999, 2003, 2004-2005, and the current dome growth that began in February of 2007. Each of these episodes was marked by lava extrusion forming a dome and lava flows, followed by explosions that destroyed the dome. The Correlation Spectrometer (COSPEC) was used to determine SO2 emission rates on 164 days from May 2003 to February 2007, using both stationary ground based scans and some flight traverses. Scans were separated into the categories of explosive degassing and passive, or background degassing. These scans show variation in the SO2 flow rate from below detection limit (~3 t/d depending on environmental conditions) during background, passive emissions to a peak of 2949 t/d (34 kilograms/second) during an explosion on 9 October, 2004. Both passive and explosive degassing increased when there was lava extrusion in 2004 and with the increased explosive activity in 2005. These two different processes of degassing wax with each other when activity increases and wane together as well, indicating a parallel cyclicity in the volcanic eruption and degassing rates, where the conduit partially seals (pressurizes) between explosions. Colima’s gas and eruptive behavior is compared to similar systems such as Santiaguito and Soufrière Hills, Montserrat. About 2/3 of Colima’s SO2 degassing, amounting to 1.3 x 105 tonnes in 3.74 yrs has come in short lived small (VEI=0-1) vertical explosions that occurred at the rate of 100-3000explosions/ month, and the remaining third has occured in continuous passive degassing. Colima emits sulfur at a rate equivalent to about 0.04 to 0.08 wt % S, similar to other andesitic convergent plate boundary volcanoes. There has been an explosive destruction of the dome in every cycle for that past 5 years, and it is assumed that the current dome which began growth in February, 2007 (just at the end of this study) will be destroyed. Higher emission rates seen in the quiescence of 2006 may have eased the pressure at the time, resulting in the slow effusion of the current dome and lack of explosivity.

Understanding volcanic processes using UV camera measurements of sulfur dioxide and coincident infrasound and seismicity

The exsolution of volatiles from magma maintains an important control on volcanic eruption styles. The nucleation, growth, and connectivity of bubbles during magma ascent provide the driving force behind eruptions, and the rate, volume, and ease of gas exsolution can affect eruptive activity. Volcanic plumes are the observable consequence of this magmatic degassing, and remote sensing techniques allow us to quantify changes in gas exsolution. However, until recently the methods used to measure volcanic plumes did not have the capability of detecting rapid changes in degassing on the scale of standard geophysical observations. The advent of the UV camera now makes high sample rate gas measurements possible. This type of dataset can then be compared to other volcanic observations to provide an in depth picture of degassing mechanisms in the shallow conduit. The goals of this research are to develop a robust methodology for UV camera field measurements of volcanic plumes, and utilize this data in conjunction with seismoacoustic records to illuminate degassing processes. Field and laboratory experiments were conducted to determine the effects of imaging conditions, vignetting, exposure time, calibration technique, and filter usage on the UV camera sulfur dioxide measurements. Using the best practices determined from these studies, a field campaign was undertaken at Volcán de Pacaya, Guatemala. Coincident plume sulfur dioxide measurements, acoustic recordings, and seismic observations were collected and analyzed jointly. The results provide insight into the small explosive features, variations in degassing rate, and plumbing system of this complex volcanic system. This research provides useful information for determining volcanic hazard at Pacaya, and demonstrates the potential of the UV camera in multiparameter studies.

Observations of volcanic emissions using satellite remote sensing

Volcanoes pose a threat to the human population at regional and global scales and so efficient monitoring is essential in order to effectively manage and mitigate the risks that they pose. Volcano monitoring from space has been possible for over thirty years and now, more than ever, a suite of instruments exists with the capability to observe emissions of gas and ash from a unique perspective. The goal of this research is to demonstrate the use of a range of satellite-based sensors in order to detect and quantify volcanic sulphur dioxide, and to assess the relative performances of each sensor against one another. Such comparisons are important in order to standardise retrievals and permit better estimations of the global contribution of sulphur dioxide to the atmosphere from volcanoes for climate modelling. In this work, retrievals of volcanic sulphur dioxide from a number of instruments are compared, and the individual performances at quantifying emissions from large, explosive volcanic eruptions are assessed. Retrievals vary widely from sensor to sensor, and often the use of a number of sensors in synergy can provide the most complete picture, rather than just one instrument alone. Volcanic emissions have the ability to result significant economic loses by grounding aircraft due to the high risk associated with ash encountering aircraft. As sulphur dioxide is often easier to measure than ash, it is often used as a proxy. This work examines whether this is a reasonable assumption, using the Icelandic eruption in early 2010 as a case study. Results indicate that although the two species are for the most part collocated, separation can occur under some conditions, meaning that it is essential to accurately measure both species in order to provide effective hazard mitigation. Finally, the usefulness of satellite remote sensing in quantifying the passive degassing from Turrialba, Costa Rica is demonstrated. The increase in activity from 2005 – 2010 can be observed in satellite data prior to the phreatic phase of early 2010, and can therefore potentially provide a useful indication of changing activity at some volcanoes.

TECHNOLOGICAL ADVANCEMENT IN REMOTE SENSING AND INNOVATIVE APPLICATION TO VOLCANOLOGY

The integration of remote monitoring techniques at different scales is of crucial importance for monitoring of volcanoes and assessment of the associated hazard. In this optic, technological advancement and collaboration between research groups also play a key role. Vhub is a community cyberinfrastructure platform designed for collaboration in volcanology research. Within the Vhub framework, this dissertation focuses on two research themes, both representing novel applications of remotely sensed data in volcanology: advancement in the acquisition of topographic data via active techniques and application of passive multi-spectral satellite data to monitoring of vegetated volcanoes. Measuring surface deformation is a critical issue in analogue modelling of Earth science phenomena. I present a novel application of the Microsoft Kinect sensor to measurement of vertical and horizontal displacements in analogue models. Specifically, I quantified vertical displacement in a scaled analogue model of Nisyros volcano, Greece, simulating magmatic deflation and inflation and related surface deformation, and included the horizontal component to reconstruct 3D models of pit crater formation. The detection of active faults around volcanoes is of importance for seismic and volcanic hazard assessment, but not a simple task to be achieved using analogue models. I present new evidence of neotectonic deformation along a north-south trending fault from the Mt Shasta debris avalanche deposit (DAD), northern California. The fault was identified on an airborne LiDAR campaign of part of the region interested by the DAD and then confirmed in the field. High resolution LiDAR can be utilized also for geomorphological assessment of DADs, and I describe a size-distance analysis to document geomorphological aspects of hummock in the Shasta DAD. Relating the remote observations of volcanic passive degassing to conditions and impacts on the ground provides an increased understanding of volcanic degassing and how satellite-based monitoring can be used to inform hazard management strategies in nearreal time. Combining a variety of satellite-based spectral time series I aim to perform the first space-based assessment of the impacts of sulfur dioxide emissions from Turrialba volcano, Costa Rica, on vegetation in the surrounding environment, and establish whether vegetation indices could be used more broadly to detect volcanic unrest.