Top-Hat HELLISH-VCSOA for optical amplification and wavelength conversion for 0.85 to 1.3ìm operation

The Top-Hat hot electron light emission and lasing in semiconductor heterostructure (HELLISH)-vertical cavity semiconductor optical amplifier (VCSOA) is a modified version of a HELLISH-VCSOA device. It has a shorter p-channel and longer n-channel. The device studied in this work consists of a simple GaAs p-i-n junction, containing 11 Ga0.35In0.65 N0.02As0.08/GaAs multiple quantum wells in its intrinsic region; the active region is enclosed between six pairs of GaAs/AlAs top distributed Bragg reflector (DBR) mirrors and 20.5 pairs of AlAs/GaAs bottom DBR mirrors. The operation of the device is based on longitudinal current transport parallel to the layers of the GaAs p-n junction. The device is characterised through I-V-L and by spectral photoluminescence, electroluminescence and electro-photoluminescence measurements. An amplification of about 25 dB is observed at applied voltages of around V = 88 V.

Selective area growth and characterization of InGaN nano-disks implemented in GaN nanocolumns with different top morphologies

This work reports on the morphology control of the selective area growth of GaN-based nanostructures on c-plane GaN templates. By decreasing the substrate temperature, the nanostructures morphology changes from pyramidal islands (no vertical m-planes), to GaN nanocolumns with top semipolar r-planes, and further to GaN nanocolumns with top polar c-planes. When growing InGaN nano-disks embedded into the GaN nanocolumns, the different morphologies mentioned lead to different optical properties, due to the semi-polar and polar nature of the r-planes and c-planes involved. These differences are assessed by photoluminescence measurements at low temperature and correlated to the specific nano-disk geometry.

Propiedades ópticas y estructurales de nanoestructuras de Zn(Cd)(Mg)O

En la presente tesis doctoral se ha realizado un estudio utilizando diferentes técnicas de crecimiento (RPE-MOCVD y spray pyrolysis) y estructuras (nanohilos, pozos y puntos cuánticos y capas) con el objetivo de desarrollar dispositivos que cubran desde el rango visible hasta el ultravioleta. Es por esta razón por la que se han elegido materiales basados en ZnO, debido a la posibilidades que estos ofrecen para variar su bandgap en un amplio rango de energías. Prueba de ello es que en este estudio se ha conseguido cubrir un rango espectral desde 1.86 hasta 4.11 eV, estudiandose además fenómenos físicos como son la difusión e incorporaci ón de la aleación o la adsorción de gases en la super_cie, lo que ha permitido la fabricación de diferentes fotodetectores de gran sensibilidad. Por todo ello, los resultados obtenidos en esta tesis suponen una gran contribución al conocimiento de las propiedades físicas de las aleaciones de Zn(Cd)O y Zn(Mg)O para potenciales aplicaciónes en dispositivos que operen en el rango visible y ultravioleta del espectro, respectivamente. En esta memoria se da en primer lugar una visión de las propiedades de materiales basados en ZnO, entrando en detalle en una de las ventajas que este presenta, la facilidad que tiene este material para formar nanoestructuras. En el capítulo 3 se dan los conceptos teóricos necesarios para comprender las propiedades ópticas de este tipo de materiales, mostrando también los resultados más reseñables obtenidos en ZnO. En los capítulos referentes a los resultados se pueden diferenciar dos grandes bloques. En el primer bloque de resultados se han analizado nanohilos y pozos cuánticos de Zn(Cd)O crecidos por la técnica de RPE-MOCVD (Capítulos 4 y 5). En el segundo se expondrá el estudio realizado sobre capas y puntos cuánticos de Zn(Mg)O crecidos por la técnica spray pyrolysis como se describe en mayor detalle a continuación. Nanohilos y pozos cuánticos de Zn(Cd)O crecidos por RPE-MOCVD Teóricamente aleando el ZnO con CdO es posible disminuir el valor del band- gap desde 3.37 eV hasta 0.95 eV, cubriendo por completo el espectro visible. El desarrollo del ternario Zn(Cd)O permitiría la fabricación de heteroestructuras y pozos cuánticos, muy importantes en el desarrollo de dispositivos optoelectrónicos que cubran la parte visible del espectro. Sin embargo, la diferencia de estructura cristalina entre estos dos materiales junto a la baja solubilidad del Cd y su alta presión de vapor, di_culta la obtención de material de alta calidad cristalina con alto contenido en Cd. En esta tesis doctoral se ha realizado una completa caracterización óptica y estructural de nanohilos de Zn(Cd)O credidos por la técnica de RPE-MOCVD. Estos nanohilos tinene unas longitudes comprendidas entre 1 y 3 _m y diámetros entre 100 y 200 nm. La concentración máxima introducida de Cd en estas estructuras ha sido de hasta un 54% manteniendo la estructura wurtzita del ZnO, siendo este el mayor contenido de Cd introducido hasta la fecha en nanostructuras basada en ZnO. Este hecho se traduce en una variación de la energía de emisión entre 3.31 y 1.86 eV con el aumento en Cd. El uso de diferentes técnicas de alta resoluci ón de caracterización estructural ha permitido demostrar la presencia de una sola fase estructural wurtzita sin observarse ningún indicio de separación de fases ni acumulación de Cd a lo largo del nanohilo para todos los contenidos de Cd. Con el propósito de fabricar dispositivos en nanohilos individuales, parte de esta tesis doctoral ha estado dedicada a estudiar el impacto que el recocido térmico tiene en las propiedades ópticas y eléctricas de nanohilos de Zn(Cd)O. El recocido térmico es un proceso clave en la optimización de dispositivos, ya sea para la obtenci ón de contactos óhmicos, reducción de defectos o difusión de dopantes por ejemplo. En este estudio se ha observado una mejora muy signi_cativa de las propiedades de emisión de los nanohilos cuando estos eran recocidos a temperaturas mayores que la de crecimiento (300 oC). En las muestras con Cd se ha observado además que el recocido también produce un desplazamiento de la emisión hacia mayores energías debido a una reducción homogénea del contenido de Cd. Medidas de fotoluminiscencia con resolución temporal muestran el impacto que tiene la localización del excitón en las _uctuaciones de potencial, debidas a una distribución estadística del Cd, en la dinámica de los portadores. Comparando el tiempo de vida de los portadores entre los nanohilos recocidos y sin recocer se ha observado un aumento de este parámetro en las estructuras recocidas. Este aumento es fundamentalmente debido a una reducción de centros de recombinación no radiativa asociados a defectos presentes a lo largo del nanohilo. Además, se ha estudiado la evolución de los tiempos de vida de los portadores en función de la temperatura, registrándose una menor estabilidad con la temperatura de los tiempos de vida en las muestras recocidas. Este resultado sugiere que el recocido térmico consigue reducir parte del desorden de la aleación en la estructura. Tras haber caracterizados los nanohilos se desarrollaron una serie de procesa dos para la fabricación de dispositivos basados en nanohilos individuales. Se fabricaron en concreto fotodetectores sensibles al UV, en los que se observó también la alta sensibilidad que muestran a la adsorción de gases en la super_cie, incrementada por la gran relación super_cie/volúmen característica de las nanoestructuras. Estos procesos de adsorción observados tienen un impacto directo sobre las propiedades ópticas y electricas de los dispositivos como se ha demostrado. Por ello que en esta tesis se hayan estudiado en detalle este tipo de procesos, ideando maneras para tener un mayor control sobre ellos. Finalmente se crecieron estructuras de pozos cuántico de ZnCdO/ZnO en nanohilos con contenidos de Cd nominales de 54 %. Las medidas ópticas realizadas mostraron como al aumentar la anchura del pozo de 0.7 a 10 nm, la emisión relacionada con el pozo se desplazaba entre 3.30 y 1.97 eV. Este gran desplazamiento representa el mayor obtenido hasta la fecha en pozos cuánticos de ZnCdO/ZnO. Sin embargo, al caracterizar estructuralmente estas muestras se observó la presencia de procesos de difusión de Cd entre el pozo y la barrera. Como se ha podido medir, este tipo de procesos reducen sustancialmente la concentración de Cd en el pozo al difundirse parte a la barrera. cambiando completamente la estructura de bandas nominal de estas estructuras. Este estudio demuestra la importancia del impacto de los procesos de difusión en la interpretación de los efectos de con_namiento cuántico para este tipo de estructuras. Capas y puntos cuánticos de Zn(Mg)O crecidos por spray pyrolysis La técnica de spray pyrolysis, debido a su simplicidad, bajo coste y capacidad de crecer sobre grandes áreas conservando una alta calidad cristalina presenta un gran interés en la comunidad cientí_ca para el potencial desarrollo de dispositivos comerciales. En esta tesis se ha estudiado las propiedades ópticas y eléctricas de capas y puntos cuánticos de Zn(Mg)O crecidos por esta técnica. Al contrario que pasa con el Cd, al introducir Mg en la estructura wurtzita de ZnO se consigue aumentar el bandgap del semiconductor. Sin embargo, al igual que pasa con el CdO, la diferencia de estructura cristalina entre el ZnO y el MgO limita la cantidad de Mg que se puede incorporar, haciendo que para una cierta concentración de Mg aparezcan el fenómeno de separación de fases. En esta tesis se ha conseguido incorporar hasta un contenido de Mg del 35% en la estructura wurtzita del ZnO utilizando la técnica de spray pyrolysis, resultado que representa la mayor concentración de Mg publicada hasta la fecha. Este hecho ha posibilitado variar la energía del borde de absorción desde 3.30 a 4.11 eV. En estas capas se ha realizado una completa caracterización óptica observándose una diferencia entre las energías del borde de absorción y del máximo de emisión creciente con el contenido en Mg. Esta diferencia, conocida como desplazamiento de Stokes, es debida en parte a la presencia de _uctuaciones de potencial producidas por un desorden estadístico de la aleación. Se han fabricado fotodetectores MSM de alta calidad utilizando las capas de Zn(Mg)O previamente caracterizadas, observándose un desplazamiento del borde de absorción con el aumento en Mg desde 3.32 a 4.02 eV. Estos dispositivos muestran altos valores de responsividad (10-103 A/W) y altos contrastes entre la responsividad bajo iluminación y oscuridad (10-107). Estos resultados son en parte debidos a la presencia de mecanismos de ganancia y una reducción de la corriente de oscuridad en las muestras con alto contenido de Mg. Utilizando esta misma técnica de crecimiento se han crecido puntos de Zn(Mg)O con concentraciones nominales de Mg entre 0 y 100 %, con dimensiones medias entre 4 y 6 nm. Las medidas estructurales realizadas muestran que hasta un valor de Mg de 45 %, los puntos están compuestos por una única fase estructural, wurtzita. A partir de esa concentración de Mg aparece una fase cúbica en los puntos, coexistiendo con la fase hexagonal hasta una concentración nominales del 85 %. Para concentraciones mayores de Mg, los puntos muestran una única fase estructural cúbica. Medidas de absorción realizadas en estos puntos de Zn(Mg)O muestran un desplazamiento del borde de absorción entre 3.33 y 3.55 eV cuando la concentraci ón de Mg en los puntos aumenta hasta el 40 %. Este desplazamiento observado es debido solamente a la fase wurtzita del Zn(Mg)O donde se incorpora el Mg. ABSTRACT This PhD theis presents a study using di_erent growth techniques (RPEMOCVD and spray pyrolysis) and structures (nanowires, quantum dots and wells and layers) in order to develop devices that extend from the visible to the ultraviolet range. For this reason ZnO based materials have been choosen, because they o_er the possibility to tunne the bandgap in this energy range. Proof of this is that this study has managed to cover a spectral range from 1.86 to 4.11 eV, also being studied physical phenomena such as di_usion and incorporation of alloy or adsorption of gases on the surface, allowing the develop di_erent highly sensitive photodetectors. Therefore, the results obtained in this thesis are a great contribution two large blockso the knowledge of the physical properties of alloys Zn(Cd)O and Zn(Mg)O for potential applications in devices that operate in the visible and ultraviolet range, respectively. In the _rst chapter, the general properties of ZnO-based materials are presented, showing the facilities that these kind of materials o_er to obtain di_erent nanoestructures. In Chapter 3, optical theoretical concepts are given to understand the optical properties of these materials, also showing the most signi_cant results of ZnO. In the chapters related with the results, two blocks could be distinguish. In the _rst one, Zn(Cd)O nanowires and quantum wells grown by RPE-MOCVD have been analyzed (Chapters 4 and 5). The second block of results shows the study performed in Zn(Mg)O _lms and quantum dots grown by spray pyrolysis. Zn(Cd)O nanowires and quantum wells grown by RPE-MOCVD In summary, the results of the PhD thesis are a great contribution to the knowledge of the physical properties of Zn(Cd)O and Zn(Mg)O alloys and their application for high performance devices operating in the visible and UV ranges, respectively. The performance of the device is still limited due to alloy solubility and p-doping stability, which opens a door for future research in this _eld. Theoretically, annealing ZnO with CdO allows to reduce the bandgap from 3.37 to 0.95 eV, covering the whole visible spectrum. The development of ZnCdO alloys allows the fabrication of heterostructures and quantum wells, necessary for the development of high performance optoelectronic devices. However, the di_erent crystal structures between CdO and ZnO and the low solubility of Cd and its high vapor pressure, hinders the growth of ZnCdO alloys with high Cd contents. In this PhD thesis Zn(Cd)O nanowires have been optically and structurally characterized, obtaining a maximum Cd content of 54% while maintaining their wurtzite structure. This Cd content, which allows lowering the bandgap down to 1.86 eV, is the highest concentration ever reported in nanostructures based on ZnO. The combination of optical and structural characterization techniques used during this thesis has allowed the demonstration of the presence of a single wurtzite structure, without observing any indication of phase separation or Cd accumulation along the nanowire. Annealing processes are essential in the fabrication of optoelectronic devices. For this reason, a complete study of the annealing e_ects in the optical and electrical properties of Zn(Cd)O nanowires has been performed. In the _rst place, annealing nanowires at higher temperatures than their growth temperature (300 oC) allows a signi_cant improvement of their emission properties. However, in the samples that contain Cd a shift in the emission towards higher energies has been observed due to a homogeneous reduction of the Cd content in the nanowires. Time resolved photoluminescence measurements show the impact of the exciton localization in the potential _uctuations due to a statistical alloy disorder. An increase in the carrier lifetime has been obtained for the annealed nanowires. This increase is mainly due to the reduction of non-radiative recombination centers associated with the defects present in the material. Furthermore, temperature dependent time resolved photoluminescence measurements suggest a reduction of the alloy disorder in the annealed samples. In this thesis, single nanowire photodetectors with a high responsivity in the UV range have been demonstrated. Due to the high surface/volume ratio, these structures are very sensitive to gas adsorption at the surface, which largely de_nes the optical and electrical properties of the material and, therefore, of the device. With the aim of obtaining time stable devices, the dynamic adsorption-desorption processes have been studied, developing di_erent approaches that allow a higher control over them. Finally, ZnCdO/ZnO quantum wells have been grown with a nominal Cd concentration of 54% inside the well. The performed optical measurements show that increasing the well width from 0.7 to 10 nm, shifts the emission related with the well from 3.30 to 1.97 eV. This result represents the highest shift reported in the literature. However, a detailed structural characterization shows the presence of di_usion phenomena which substantially reduce the concentration of Cd in the well, while increasing it in the barrier. This type of phenomena should be considered when ac curately interpretating the quantum con_nement e_ects in Zn(Cd)O/ZnO quantum wells. Theoretically, annealing ZnO with CdO allows to decrease the bandgap from 3.37 to 0.95 eV, covering the whole visible spectrum. Zn(Mg)O _lms and quantum dots grown by spray pyrolysis Due to its simplicity, low-cost and capacity to grow over large areas conserving a high crystal quality, spray pyrolysis technique presents a great interest in the scienti_c community for developing comercial devices. In this thesis, a complete study of the optical and structural properties of Zn(Mg)O _lms and quantum dots grown by spray pyrolysis has been performed. Contrary to Zn(Cd)O alloys, when introducing Mg in the ZnO wurtzite structure an increase in the bandgap in obtained. Once again, the di_erence in the crystal structure of ZnO and MgO limits the amount of Mg that can be introduced before phase separation appears. In this PhD thesis, a maximum Mg content of 35% has been incorporated in the wurtzite structure using spray pyrolysis. This variation in the Mg content translates into an increase of the absorption edge from 3.30 to 4.11 eV. Up to this date, this result represents the highest Mg content introduced by spray pyrolysis in a ZnO wurzite structure reported in the literature. The comparison of the emission and absorption spectra shows the presence of an increasing Stokes shift with Mg content. This phenomenon is partialy related with the presence of potential _uctuations due to an statistic alloy disorder. MSM photodetectors have been processed on previously characterized Zn(Mg)O _lms. These devices have shown a shift in the absorption edge from 3.32 to 4.02 eV with the increase in Mg content, high responsivity values (10-103 A/W) and high contrast ratios between illuminated and dark responsivities (10-107). These values are explained by the presence of a gain mechanism and a reduction of dark current in the ZnMgO samples. Zn(Mg)O quantum dots have also been grown using spray pyrolysis with Mg concentrations between 0 and 100% and with average widths ranging 4 to 6 nm. Structural measurements show that at a Mg concentration of 45% the cubic phase appears, coexisting with the hexagonal phase up to an 85% concentration of Mg content. From 85% onwards the quantum dots show only the cubic phase. Absorption measurements performed in these structures reveal a shift in the absorption edge from 3.33 to 3.55 eV when the Mg content increases up to 40 %.

Heterogeneously grown tunable group-IV laser on silicon

Tunable tensile-strained germanium (epsilon-Ge) thin films on GaAs and heterogeneously integrated on silicon (Si) have been demonstrated using graded III-V buffer architectures grown by molecular beam epitaxy (MBE). epsilon-Ge epilayers with tunable strain from 0% to 1.95% on GaAs and 0% to 1.11% on Si were realized utilizing MBE. The detailed structural, morphological, band alignment and optical properties of these highly tensile-strained Ge materials were characterized to establish a pathway for wavelength-tunable laser emission from 1.55 μm to 2.1 μm. High-resolution X-ray analysis confirmed pseudomorphic epsilon-Ge epitaxy in which the amount of strain varied linearly as a function of indium alloy composition in the InxGa1-xAs buffer. Cross-sectional transmission electron microscopic analysis demonstrated a sharp heterointerface between the epsilon-Ge and the InxGa1-xAs layer and confirmed the strain state of the epsilon-Ge epilayer. Lowtemperature micro-photoluminescence measurements confirmed both direct and indirect bandgap radiative recombination between the Γ and L valleys of Ge to the light-hole valence band, with L-lh bandgaps of 0.68 eV and 0.65 eV demonstrated for the 0.82% and 1.11% epsilon-Ge on Si, respectively. The highly epsilon-Ge exhibited a direct bandgap, and wavelength-tunable emission was observed for all samples on both GaAs and Si. Successful heterogeneous integration of tunable epsilon-Ge quantum wells on Si paves the way for the implementation of monolithic heterogeneous devices on Si.

Role of substrate quality on the performance of semipolar (11 2 - 2) InGaN light-emitting diodes

We compare the optical properties and device performance of unpackaged InGaN/GaN multiple-quantum-well light-emitting diodes (LEDs) emitting at ∼430 nm grown simultaneously on a high-cost small-size bulk semipolar (11 2 - 2) GaN substrate (Bulk-GaN) and a low-cost large-size (11 2 - 2) GaN template created on patterned (10 1 - 2) r-plane sapphire substrate (PSS-GaN). The Bulk-GaN substrate has the threading dislocation density (TDD) of ∼ and basal-plane stacking fault (BSF) density of 0 cm-1, while the PSS-GaN substrate has the TDD of ∼2 × 108cm-2 and BSF density of ∼1 × 103cm-1. Despite an enhanced light extraction efficiency, the LED grown on PSS-GaN has two-times lower internal quantum efficiency than the LED grown on Bulk-GaN as determined by photoluminescence measurements. The LED grown on PSS-GaN substrate also has about two-times lower output power compared to the LED grown on Bulk-GaN substrate. This lower output power was attributed to the higher TDD and BSF density.

Thermal lens and interferometric method for glass transition and thermo physical properties measurements in Nd(2)O(3) doped sodium zincborate glass

In this work the time resolved thermal lens method is combined with interferometric technique, the thermal relaxation calorimetry, photoluminescence and lifetime measurements to determine the thermo physical properties of Nd(2)O(3) doped sodium zincborate glass as a function of temperature up to the glass transition region. Thermal diffusivity, thermal conductivity, fluorescence quantum efficiency, linear thermal expansion coefficient and thermal coefficient of electronic polarizability were determined. In conclusion, the results showed the ability of thermal lens and interferometric methods to perform measurements very close to the phase transition region. These techniques provide absolute values for the measured physical quantities and are advantageous when low scan rates are required. (c) 2008 Optical Society of America

Photoluminescence and electrical study of fluctuating potentials in Cu2ZnSnS4-based thin films

In this work, we investigated structural, morphological, electrical, and optical properties from a set of Cu2ZnSnS4 thin films grown by sulfurization of metallic precursors deposited on soda lime glass substrates coated with or without molybdenum. X-ray diffraction and Raman spectroscopy measurements revealed the formation of single-phase Cu2ZnSnS4 thin films. A good crystallinity and grain compactness of the film was found by scanning electron microscopy. The grown films are poor in copper and rich in zinc, which is a composition close to that of the Cu2ZnSnS4 solar cells with best reported efficiency. Electrical conductivity and Hall effect measurements showed a high doping level and a strong compensation. The temperature dependence of the free hole concentration showed that the films are nondegenerate. Photoluminescence spectroscopy showed an asymmetric broadband emission. The experimental behavior with increasing excitation power or temperature cannot be explained by donor-acceptor pair transitions. A model of radiative recombination of an electron with a hole bound to an acceptor level, broadened by potential fluctuations of the valence-band edge, was proposed. An ionization energy for the acceptor level in the range 29–40 meV was estimated, and a value of 172 ±2 meV was obtained for the potential fluctuation in the valence-band edge.

Optical-geometrical effects on the photoluminescence spectra of Si nanocrystals embedded in SiO2

We demonstrate that thickness, optical constants, and details of the multilayer stack, together with the detection setting, strongly influence the photoluminescence spectra of Si nanocrystals embedded in SiO2. Due to multiple reflections of the visible light against the opaque silicon substrate, an interference pattern is built inside the oxide layer, which is responsible for the modifications in the measured spectra. This interference effect is complicated by the depth dependence of (i) the intensity of the excitation laser and (ii) the concentration of the emitting nanocrystals. These variations can give rise to apparent features in the recorded spectra, such as peak shifts, satellite shoulders, and even splittings, which can be mistaken as intrinsic material features. Thus, they can give rise to an erroneous attribution of optical bands or estimate of the average particle size, while they are only optical-geometrical artifacts. We have analyzed these effects as a function of material composition (Si excess fraction) and thickness, and also evaluated how the geometry of the detection setup affects the measurements. To correct the experimental photoluminescence spectra and extract the true spectral shape of the emission from Si nanocrystals, we have developed an algorithm based on a modulation function, which depends on both the multilayer sequence and the experimental configuration. This procedure can be easily extended to other heterogeneous systems.

Anisotropie de la photoluminescence dans des nanostructures organiques chirales autoassemblées

Nous investiguons dans ce travail la dynamique des excitons dans une couche mince d’agrégats H autoassemblés hélicoïdaux de molécules de sexithiophène. Le couplage intermoléculaire (J=100 meV) place ce matériau dans la catégorie des semi-conducteurs à couplage de type intermédiaire. Le désordre énergétique et la forte interaction électronsphonons causent une forte localisation des excitons. Les espèces initiales se ramifient en deux états distincts : un état d’excitons autopiégés (rendement de 95 %) et un état à transfert de charge (rendement de 5%). À température de la pièce (293K), les processus de sauts intermoléculaires sont activés et l’anisotropie de la fluorescence décroît rapidement à zéro en 5 ns. À basse température (14K), les processus de sauts sont gelés. Pour caractériser la dynamique de diffusion des espèces, une expérience d’anisotropie de fluorescence a été effectuée. Celle-ci consiste à mesurer la différence entre la photoluminescence polarisée parallèlement au laser excitateur et celle polarisée perpendiculairement, en fonction du temps. Cette mesure nous donne de l’information sur la dépolarisation des excitons, qui est directement reliée à leur diffusion dans la structure supramoléculaire. On mesure une anisotropie de 0,1 après 20 ns qui perdure jusqu’à 50ns. Les états à transfert de charge causent une remontée de l’anisotropie vers une valeur de 0,15 sur une plage temporelle allant de 50 ns jusqu’à 210 ns (période entre les impulsions laser). Ces résultats démontrent que la localisation des porteurs est très grande à 14K, et qu’elle est supérieure pour les espèces à transfert de charge. Un modèle numérique simple d’équations différentielles à temps de vie radiatif et de dépolarisation constants permet de reproduire les données expérimentales. Ce modèle a toutefois ses limitations, notamment en ce qui a trait aux mécanismes de dépolarisation des excitons.

Non-destructive evaluation of photovoltaic materials and solar cells using Photoluminescence

Photoluminescence (PL) spectroscopy is an optical technique that has emerged successful in the field of semiconductor material and device characterization. This technique is quite a powerful one which gives idea about the defect levels in a material, the band gap of the material, composition as well as material quality. Over the recent years it has received an elevation as a mainstream characterization technique. This thesis is an attempt to characterize each individual layer used in a thin film solar cell with special focus on the electrical properties. This will be highly beneficial from the lab as well as industrial point of view because electrical measurements generally are contact mode measurements which tend to damage the surface. As far as a thin film solar cell is concerned, the constituent layers are the transparent conducting oxide (TCO), absorber layer, buffer layer and top electrode contact. Each layer has a specific role to play and the performance of a solar cell is decided and limited by the quality of each individual layer. Various aspects of PL spectroscopy have been employed for studying compound semiconductor thin films [deposited using chemical spray pyrolysis (CSP)] proposed for solar cell application. This thesis has been structured in to seven chapters

Reliable and Damage-Free Estimation of Resistivity of ZnO Thin Films for Photovoltaic Applications Using Photoluminescence Technique

This work projects photoluminescence (PL) as an alternative technique to estimate the order of resistivity of zinc oxide (ZnO) thin films. ZnO thin films, deposited using chemical spray pyrolysis (CSP) by varying the deposition parameters like solvent, spray rate, pH of precursor, and so forth, have been used for this study. Variation in the deposition conditions has tremendous impact on the luminescence properties as well as resistivity. Two emissions could be recorded for all samples—the near band edge emission (NBE) at 380 nm and the deep level emission (DLE) at ∼500 nm which are competing in nature. It is observed that the ratio of intensities of DLE to NBE ( DLE/ NBE) can be reduced by controlling oxygen incorporation in the sample. - measurements indicate that restricting oxygen incorporation reduces resistivity considerably. Variation of DLE/ NBE and resistivity for samples prepared under different deposition conditions is similar in nature. DLE/ NBE was always less than resistivity by an order for all samples.Thus from PL measurements alone, the order of resistivity of the samples can be estimated.

A new processing method of CaZn(2)(OH)(6)center dot 2H(2)O powders: Photoluminescence and growth mechanism

In this communication, we report on the formation of calcium hexahydroxodizincate dehydrate, CaZn(2)(OH)(6)center dot 2H(2)O (CZO) powders under microwave-hydrothermal (MH) conditions. These powders were analyzed by X-ray diffraction (XRD), Field-emission gum scanning electron microscopy (FEG-SEM), ultraviolet-visible (UV-vis) absorption spectroscopy and photoluminescence (PL) measurements. XRD patterns confirmed that the pure CZO phase was obtained after MH processing performed at 130 degrees C for 2 h. FEG-SEM micrographs indicated that the morphological modifications as well as the growth of CZO microparticles are governed by Ostwald-ripening and coalescence mechanisms. UV-vis spectra showed that this material have an indirect optical band gap. The pure CZO powders exhibited an yellow PL emission when excited by 350 nm wavelength at room temperature. (C) 2009 Elsevier Masson SAS. All rights reserved.

Morphology and Blue Photoluminescence Emission of PbMoO(4) Processed in Conventional Hydrothermal

PbMoO(4) micro-octahedrons were prepared by the coprecipitation method at room temperature without the presence of surfactants and processed in a conventional hydrothermal at different temperatures (from 60 to 120 degrees C) for 10 min. These micro-octahedrons were structurally characterized by X-ray diffraction (XRD) and micro-Raman (MR) spectroscopy, and its morphology was investigated by field-emission gun scanning electron microscopy (FEG-SEM). The optical properties were analyzed by ultraviolet-visible (UV-vis) absorption spectroscopy and photoluminescence (PL) measurements. XRD patterns and MR spectra confirmed that the PbMoO(4) micro-octahedrons are characterized by a scheelite-type tetragonal structure. FEG-SEM micrographs points, out that these structures present a polydisperse particle size distribution in consequence of a predominant growth mechanism via aggregation of particles. In addition, it was observed that the hydrothermal conditions favored a spontaneous formation of micro-octahedrons interconnected along a common crystallographic orientation (oriented-attachment), resulting in self-organized structures. An intense blue PL emission at room temperature was observed in these micro-octahedrons when they were excited with a 350 nm wavelength. The origin of the PL emissions as well as its intensity variations are explained by means of a model based on both distorted [MoO(4)] and [PbO(8)] clusters into the lattice.

A Multitechnique Study of Structure and Dynamics of Polyfluorene Cast Films and the Influence on Their Photoluminescence

This article describes the microstructure and dynamics in the solid state of polyfluorene-based polymers, poly(9,)-dioctylfluorenyl-2,7-diyl) (PFO), a semicrystalline polymer, and poly [(9,9-dioctyl- 2,7-divinylene-fluorenylene)-alt-co-{2-methoxy-5-(2-ethyl-hexyloxy)- 1,4-phenylene vinylene}, a copolymer with mesomorphic phase properties. These Structures were determined by wide-angle X-ray scattering (WAXS) measurements, Assuming a packing model for the copolymer structure, where the planes of the phenyl rings are stacked and separated by an average distance of similar to 4.5 angstrom and laterally spaced by about similar to 16 angstrom, we followed the evolution of these distances as a function of temperature using WAXS and associated the changes observed to the polymer relaxation processes identified by dynamical mechanical thermal analysis. Specific molecular motions were studied by solid-state nuclear magnetic resonance. The onset of the side-chain motion at about 213 K (beta-relaxation) produced a small increase in the lateral spacing and in the stacking distance of the phenyl rings in them aggregated Structures, Besides, at about 383 K (alpha-relaxation) there occurs a significant increase in the amplitude of the torsion motion in the backbone, producing a greater increase in the stacking distance of the phenyl rings. Similar results were observed in the semicrystalline phase of PFO, but in this case the presence of the crystalline structure affects considerably the overall dynamics, which tends to be more hindered. Put together, Our data explain many features of the temperature dependence of the photoluminescence of these two polymers.