Control and protection of a microgrid with converter interfaced micro sources

This paper describes protection and control of a microgrid with converter interfaced micro sources. The proposed protection and control scheme consider both grid connected and autonomous operation of the microgrid. A protection scheme, capable of detecting faults effectively in both grid connected and islanded operations is proposed. The main challenge of the protection, due to current limiting state of the converters is overcome by using admittance relays. The relays operate according to the inverse time characteristic based on measured admittance of the line. The proposed scheme isolates the fault from both sides, while downstream side of the microgrid operates in islanding condition. Moreover faults can be detected in autonomous operation. In grid connected mode distributed generators (DG) supply the rated power while in absence of the grid, DGs share the entire power requirement proportional to rating based on output voltage angle droop control. The protection scheme ensures minimum load shedding with isolating the faulted network and DG control provides a smooth islanding and resynchronization operation. The efficacy of coordinated control and protection scheme has been validated through simulation for various operating conditions.

Distortional buckling tests of cold-formed steel compression members at elevated temperatures

In recent times, light gauge cold-formed steel sections have been used extensively since they have a very high strength to weight ratio compared with thicker hot-rolled steel sections. However, they are susceptible to various buckling modes including a distortional mode and hence show complex behaviour under fire conditions. Therefore a research project based on detailed experimental studies was undertaken to investigate the distortional buckling behaviour of light gauge cold-formed steel compression members under simulated fire conditions. More than 150 axial compression tests were undertaken at uniform ambient and elevated temperatures. Two types of cross sections were selected with nominal thicknesses of 0.60, 0.80, and 0.95 mm. Both low (G250) and high (G550) strength steels were used. Distortional buckling tests were conducted at six different temperatures in the range of 20 to 800°C. The ultimate loads of compression members subject to distortional buckling were then used to review the adequacy of the current design rules at ambient and elevated temperatures. This paper presents the details of this experimental study and the results.

Modeling corneal surfaces with rational functions for high-speed videokeratoscopy data compression

High-speed videokeratoscopy is an emerging technique that enables study of the corneal surface and tear-film dynamics. Unlike its static predecessor, this new technique results in a very large amount of digital data for which storage needs become significant. We aimed to design a compression technique that would use mathematical functions to parsimoniously fit corneal surface data with a minimum number of coefficients. Since the Zernike polynomial functions that have been traditionally used for modeling corneal surfaces may not necessarily correctly represent given corneal surface data in terms of its optical performance, we introduced the concept of Zernike polynomial-based rational functions. Modeling optimality criteria were employed in terms of both the rms surface error as well as the point spread function cross-correlation. The parameters of approximations were estimated using a nonlinear least-squares procedure based on the Levenberg-Marquardt algorithm. A large number of retrospective videokeratoscopic measurements were used to evaluate the performance of the proposed rational-function-based modeling approach. The results indicate that the rational functions almost always outperform the traditional Zernike polynomial approximations with the same number of coefficients.

Anterior vertebral stapling for the fusionless correction of scoliosis

Fusionless scoliosis surgery is an emerging treatment for idiopathic scoliosis as it offers theoretical advantages over current forms of treatment. Currently the treatment options for idiopathic scoliosis are observation, bracing and fusion. While brace treatment is non-invasive, and preserves the growth, motion, and function of the spine, it does not correct deformity and is only modestly successful in preventing curve progression. In adolescents who fail brace treatment, surgical treatment with an instrumented spinal fusion usually results in better deformity correction but is associated with substantially greater risk. Furthermore in younger patients requiring surgical treatment, fusion procedures are known to adversely effect the future growth of the chest and spine. Fusionless treatments have been developed to allow effective surgical treatment of patients with idiopathic scoliosis who are too young for fusion procedures. Anterior vertebral stapling is one such fusionless treatment which aims to modulate the growth of vertebra to allow correction of scoliosis whilst maintaining normal spinal motion The Mater Misericordiae Hospital in Brisbane has begun to use anterior vertebral stapling to treat patients with idiopathic scoliosis who are too young for fusion procedures. Currently the only staple approved for clinical use is manufactured by Medtronic Sofamor Danek (Memphis, TN). This thesis explains the biomechanical and anatomical changes that occur following anterior vertebral staple insertion using in vitro experiments performed on an immature bovine model. Currently there is a paucity of published information about anterior vertebral stapling so it is hoped that this project will provide information that will aid in our understanding of the clinical effects of staple insertion. The aims of this experimental study were threefold. The first phase was designed to determine the changes in the bending stiffness of the spine following staple insertion. The second phase was designed to measure the forces experienced by the staple during spinal movements. The third and final phase of testing was designed to describe the structural changes that occur to a vertebra as a consequence of staple insertion. The first phase of testing utilised a displacement controlled testing robot to compare the change in stiffness of a single spinal motion segment following staple insertion for the three basic spinal motions of flexion-extension, lateral bending, and axial rotation. For the second phase of testing strain gauges were attached to staples and used to measure staple forces during spinal movement. In the third and final phase the staples were removed and a testing specimen underwent micro-computed tomography (CT) scanning to describe the anatomical changes that occur following staple insertion. The displacement controlled testing showed that there was a significant decrease in bending stiffness in flexion, extension, lateral bending away from the staple, and axial rotation away from the staple following staple insertion. The strain gauge measurements showed that the greatest staple forces occurred in flexion and the least in extension. In addition, a reduction in the baseline staple compressive force was seen with successive loading cycles. Micro-CT scanning demonstrated that significant damage to the vertebral body and endplate occurred as a consequence of staple insertion. The clinical implications of this study are significant. Based on the findings of this project it is likely that the clinical effect of the anterior vertebral staple evaluated in this project is a consequence of growth plate damage (also called hemiepiphysiodesis) causing a partial growth arrest of the vertebra rather than simply compression of the growth plate. The surgical creation of a unilateral growth arrest is a well established treatment used in the management of congenital scoliosis but has not previously been considered for use in idiopathic scoliosis.

Droop control of converter interfaced micro sources in rural distributed generation

This paper proposes new droop control methods for load sharing in a rural area with distributed generation. Highly resistive lines, typical of rural low voltage networks, always create a big challenge for conventional droop control. To overcome the conflict between higher feedback gain for better power sharing and system stability in angle droop, two control methods have been proposed. The first method considers no communication among the distributed generators (DGs) and regulates the converter output voltage and angle ensuring proper sharing of load in a system having strong coupling between real and reactive power due to high line resistance. The second method, based on a smattering of communication, modifies the reference output volt-age angle of the DGs depending on the active and reactive power flow in the lines connected to point of common coupling (PCC). It is shown that with the second proposed control method, an economical and minimum communication system can achieve significant improvement in load sharing. The difference in error margin between proposed control schemes and a more costly high bandwidth communication system is small and the later may not be justified considering the increase in cost. The proposed control shows stable operation of the system for a range of operating conditions while ensuring satisfactory load sharing.

Towards a model of understanding strategic decision-making in micro-firms : exploring the Australian information technology sector

This study explores strategic decision-making (SDM) in micro-firms, an economically significant business subsector. As extant large- and small-firm literature currently proffers an incomplete characterization of SDM in very small enterprises, a multiple-case methodology was used to investigate how these firms make strategic decisions. Eleven Australian Information Technology service micro-firms participated in the study. Using an information-processing lens, the study uncovered patterns of SDM in micro-firms and derived a theoretical micro-firm SDM model. This research also identifies several implications for micro-firm management and directions for future research, contributing to the understanding of micro-firm SDM in both theory and practice.

Adiabatic compression testing - part I : historical development and evaluation of fluid dynamic processes including shock-wave considerations

Adiabatic compression testing of components in gaseous oxygen is a test method that is utilized worldwide and is commonly required to qualify a component for ignition tolerance under its intended service. This testing is required by many industry standards organizations and government agencies. This paper traces the background of adiabatic compression testing in the oxygen community and discusses the thermodynamic and fluid dynamic processes that occur during rapid pressure surges. This paper is the first of several papers by the authors on the subject of adiabatic compression testing and is presented as a non-comprehensive background and introduction.

Adiabatic compression testing - part II : background and approach to estimating severity of test methodology

Adiabatic compression testing of components in gaseous oxygen is a test method that is utilized worldwide and is commonly required to qualify a component for ignition tolerance under its intended service. This testing is required by many industry standards organizations and government agencies; however, a thorough evaluation of the test parameters and test system influences on the thermal energy produced during the test has not yet been performed. This paper presents a background for adiabatic compression testing and discusses an approach to estimating potential differences in the thermal profiles produced by different test laboratories. A “Thermal Profile Test Fixture” (TPTF) is described that is capable of measuring and characterizing the thermal energy for a typical pressure shock by any test system. The test systems at Wendell Hull & Associates, Inc. (WHA) in the USA and at the BAM Federal Institute for Materials Research and Testing in Germany are compared in this manner and some of the data obtained is presented. The paper also introduces a new way of comparing the test method to idealized processes to perform system-by-system comparisons. Thus, the paper introduces an “Idealized Severity Index” (ISI) of the thermal energy to characterize a rapid pressure surge. From the TPTF data a “Test Severity Index” (TSI) can also be calculated so that the thermal energies developed by different test systems can be compared to each other and to the ISI for the equivalent isentropic process. Finally, a “Service Severity Index” (SSI) is introduced to characterizing the thermal energy of actual service conditions. This paper is the second in a series of publications planned on the subject of adiabatic compression testing.

Technical note : modelling a complex micro-multileaf collimator using the standard BEAMnrc distribution

Purpose: The component modules in the standard BEAMnrc distribution may appear to be insufficient to model micro-multileaf collimators that have tri-faceted leaf ends and complex leaf profiles. This note indicates, however, that accurate Monte Carlo simulations of radiotherapy beams defined by a complex collimation device can be completed using BEAMnrc's standard VARMLC component module.---------- Methods: That this simple collimator model can produce spatially and dosimetrically accurate micro-collimated fields is illustrated using comparisons with ion chamber and film measurements of the dose deposited by square and irregular fields incident on planar, homogeneous water phantoms.---------- Results: Monte Carlo dose calculations for on- and off-axis fields are shown to produce good agreement with experimental values, even upon close examination of the penumbrae.--------- Conclusions: The use of a VARMLC model of the micro-multileaf collimator, along with a commissioned model of the associated linear accelerator, is therefore recommended as an alternative to the development or use of in-house or third-party component modules for simulating stereotactic radiotherapy and radiosurgery treatments. Simulation parameters for the VARMLC model are provided which should allow other researchers to adapt and use this model to study clinical stereotactic radiotherapy treatments.

Use of micro-ATR/FTIR imaging to study heterogeneous polymer oxidation by direct solvent casting onto the ATR IRE

A technique is described whereby micro-ATR/FTIR imaging can be used to follow polymer degradation reactions in situ in real time. The internal reflection element (IRE) assembly is removed from the ATR objective and polymer is solvent cast directly onto the IRE surface. The polymer is then subjected to degradation conditions and molecular structural changes monitored by periodically replacing the IRE assembly back in the ATR objective and collecting spectra which can be used to construct images. This approach has the benefit that the same part of the sample is always studied, and that contact by pressure which might damage the polymer surface is not required. The technique is demonstrated using the polymer Topas which was degraded by exposure to UVC light in air.

Micro-family-owned business : transitory survival mechanism or long term wealth creator?

Principal Topic: Entrepreneurship is key to employment, innovation and growth (Acs & Mueller, 2008), and as such, has been the subject of tremendous research in both the economic and management literatures since Solow (1957), Schumpeter (1934, 1943), and Penrose (1959). The presence of entrepreneurs in the economy is a key factor in the success or failure of countries to grow (Audretsch and Thurik, 2001; Dejardin, 2001). Further studies focus on the conditions of existence of entrepreneurship, influential factors invoked are historical, cultural, social, institutional, or purely economic (North, 1997; Thurik 1996 & 1999). Of particular interest, beyond the reasons behind the existence of entrepreneurship, are entrepreneurial survival and good ''performance'' factors. Using cross-country firm data analysis, La Porta & Schleifer (2008) confirm that informal micro-businesses provide on average half of all economic activity in developing countries. They find that these are utterly unproductive compared to formal firms, and conclude that the informal sector serves as a social security net ''keep[ing] millions of people alive, but disappearing over time'' (abstract). Robison (1986), Hill (1996, 1997) posit that the Indonesian government under Suharto always pointed to the lack of indigenous entrepreneurship , thereby motivating the nationalisation of all industries. Furthermore, the same literature also points to the fact that small businesses were mostly left out of development programmes because they were supposed less productive and having less productivity potential than larger ones. Vial (2008) challenges this view and shows that small firms represent about 70% of firms, 12% of total output, but contribute to 25% of total factor productivity growth on average over the period 1975-94 in the industrial sector (Table 10, p.316). ---------- Methodology/Key Propositions: A review of the empirical literature points at several under-researched questions. Firstly, we assess whether there is, evidence of small family-business entrepreneurship in Indonesia. Secondly, we examine and present the characteristics of these enterprises, along with the size of the sector, and its dynamics. Thirdly, we study whether these enterprises underperform compared to the larger scale industrial sector, as it is suggested in the literature. We reconsider performance measurements for micro-family owned businesses. We suggest that, beside productivity measures, performance could be appraised by both the survival probability of the firm, and by the amount of household assets formation. We compare micro-family-owned and larger industrial firms' survival probabilities after the 1997 crisis, their capital productivity, then compare household assets of families involved in business with those who do not. Finally, we examine human and social capital as moderators of enterprises' performance. In particular, we assess whether a higher level of education and community participation have an effect on the likelihood of running a family business, and whether it has an impact on households' assets level. We use the IFLS database compiled and published by RAND Corporation. The data is a rich community, households, and individuals panel dataset in four waves: 1993, 1997, 2000, 2007. We now focus on the waves 1997 and 2000 in order to investigate entrepreneurship behaviours in turbulent times, i.e. the 1997 Asian crisis. We use aggregate individual data, and focus on households data in order to study micro-family-owned businesses. IFLS data covers roughly 7,600 households in 1997 and over 10,000 households in 2000, with about 95% of 1997 households re-interviewed in 2000. Households were interviewed in 13 of the 27 provinces as defined before 2001. Those 13 provinces were targeted because accounting for 83% of the population. A full description of the data is provided in Frankenberg and Thomas (2000), and Strauss et alii (2004). We deflate all monetary values in Rupiah with the World Development Indicators Consumer Price Index base 100 in 2000. ---------- Results and Implications: We find that in Indonesia, entrepreneurship is widespread and two thirds of households hold one or several family businesses. In rural areas, in 2000, 75% of households run one or several businesses. The proportion of households holding both a farm and a non farm business is higher in rural areas, underlining the reliance of rural households on self-employment, especially after the crisis. Those businesses come in various sizes from very small to larger ones. The median business production value represents less than the annual national minimum wage. Figures show that at least 75% of farm businesses produce less than the annual minimum wage, with non farm businesses being more numerous to produce the minimum wage. However, this is only one part of the story, as production is not the only ''output'' or effect of the business. We show that the survival rate of those businesses ranks between 70 and 82% after the 1997 crisis, which contrasts with the 67% survival rate for the formal industrial sector (Ter Wengel & Rodriguez, 2006). Micro Family Owned Businesses might be relatively small in terms of production, they also provide stability in times of crisis. For those businesses that provide business assets figures, we show that capital productivity is fairly high, with rates that are ten times higher for non farm businesses. Results show that households running a business have larger family assets, and households are better off in urban areas. We run a panel logit model in order to test the effect of human and social capital on the existence of businesses among households. We find that non farm businesses are more likely to appear in households with higher human and social capital situated in urban areas. Farm businesses are more likely to appear in lower human capital and rural contexts, while still being supported by community participation. The estimation of our panel data model confirm that households are more likely to have higher family assets if situated in urban area, the higher the education level, the larger the assets, and running a business increase the likelihood of having larger assets. This is especially true for non farm businesses that have a clearly larger and more significant effect on assets than farm businesses. Finally, social capital in the form of community participation also has a positive effect on assets. Those results confirm the existence of a strong entrepreneurship culture among Indonesian households. Investigating survival rates also shows that those businesses are quite stable, even in the face of a violent crisis such as the 1997 one, and as a result, can provide a safety net. Finally, considering household assets - the returns of business to the household, rather than profit or productivity - the returns of business to itself, shows that households running a business are better off. While we demonstrate that uman and social capital are key to business existence, survival and performance, those results open avenues for further research regarding the factors that could hamper growth of those businesses in terms of output and employment.

Corruption and political interest : empirical evidence at the micro level

The topic of corruption has recently attracted a great deal of attention, yet there is still a lack of micro level empirical evidence regarding the determinates of corruption. Furthermore, the present literature has not investigated the effects of political interest on corruption despite the interesting potential of this link. We address these deficiencies by analysing a cross-section of individuals, using the World Values Survey. We explore the determinants of corruption through two dependant variables (perceived corruption and the justifiability of corruption). The impact of political interest on corruption is explored through three different proxies presenting empirical evidence at both the cross-country level and the within-country level.The results of the multivariate analysis suggest that political interest has an impact on corruption controlling for a huge number of factors.

Demonstration of image compression in a low-bandwidth wireless camera network

This paper presents an overview of our demonstration of a low-bandwidth, wireless camera network where image compression is undertaken at each node. We briefly introduce the Fleck hardware platform we have developed as well as describe the image compression algorithm which runs on individual nodes. The demo will show real-time image data coming back to base as individual camera nodes are added to the network. Copyright 2007 ACM.