Using long time series of agricultural-derived nitrates for estimating catchment transit times

The estimation of water and solute transit times in catchments is crucial for predicting the response of hydrosystems to external forcings (climatic or anthropogenic). The hydrogeochemical signatures of tracers (either natural or anthropogenic) in streams have been widely used to estimate transit times in catchments as they integrate the various processes at stake. However, most of these tracers are well suited for catchments with mean transit times lower than about 4-5 years. Since the second half of the 20th century, the intensification of agriculture led to a general increase of the nitrogen load in rivers. As nitrate is mainly transported by groundwater in agricultural catchments, this signal can be used to estimate transit times greater than several years, even if nitrate is not a conservative tracer. Conceptual hydrological models can be used to estimate catchment transit times provided their consistency is demonstrated, based on their ability to simulate the stream chemical signatures at various time scales and catchment internal processes such as N storage in groundwater. The objective of this study was to assess if a conceptual lumped model was able to simulate the observed patterns of nitrogen concentration, at various time scales, from seasonal to pluriannual and thus if it was relevant to estimate the nitrogen transit times in headwater catchments. A conceptual lumped model, representing shallow groundwater flow as two parallel linear stores with double porosity, and riparian processes by a constant nitrogen removal function, was applied on two paired agricultural catchments which belong to the Research Observatory ORE AgrHys. The Global Likelihood Uncertainty Estimation (GLUE) approach was used to estimate parameter values and uncertainties. The model performance was assessed on (i) its ability to simulate the contrasted patterns of stream flow and stream nitrate concentrations at seasonal and inter-annual time scales, (ii) its ability to simulate the patterns observed in groundwater at the same temporal scales, and (iii) the consistency of long-term simulations using the calibrated model and the general pattern of the nitrate concentration increase in the region since the beginning of the intensification of agriculture in the 1960s. The simulated nitrate transit times were found more sensitive to climate variability than to parameter uncertainty, and average values were found to be consistent with results from others studies in the same region involving modeling and groundwater dating. This study shows that a simple model can be used to simulate the main dynamics of nitrogen in an intensively polluted catchment and then be used to estimate the transit times of these pollutants in the system which is crucial to guide mitigation plans design and assessment. (C) 2015 Elsevier B.V. All rights reserved.

The Self-Association of Graphane Is Driven by London Dispersion and Enhanced Orbital Interactions

We investigated the nature of the cohesive energy between graphane sheets via multiple CH center dot center dot center dot HC interactions, using density functional theory (DFT) including dispersion correction (Grimmes D3 approach) computations of n]graphane sigma dimers (n = 6-73). For comparison, we also evaluated the binding between graphene sheets that display prototypical pi/pi interactions. The results were analyzed using the block-localized wave function (BLW) method, which is a variant of ab initio valence bond (VB) theory. BLW interprets the intermolecular interactions in terms of frozen interaction energy (Delta E-F) composed of electrostatic and Pauli repulsion interactions, polarization (Delta E-pol), charge-transfer interaction (Delta E-CT), and dispersion effects (Delta E-disp). The BLW analysis reveals that the cohesive energy between graphane sheets is dominated by two stabilizing effects, namely intermolecular London dispersion and two-way charge transfer energy due to the sigma CH -> sigma*(HC) interactions. The shift of the electron density around the nonpolar covalent C-H bonds involved in the intermolecular interaction decreases the C-H bond lengths uniformly by 0.001 angstrom. The Delta E-CT term, which accounts for similar to 15% of the total binding energy, results in the accumulation of electron density in the interface area between two layers. This accumulated electron density thus acts as an electronic glue for the graphane layers and constitutes an important driving force in the self-association and stability of graphane under ambient conditions. Similarly, the double faced adhesive tape style of charge transfer interactions was also observed among graphene sheets in which it accounts for similar to 18% of the total binding energy. The binding energy between graphane sheets is additive and can be expressed as a sum of CH center dot center dot center dot HC interactions, or as a function of the number of C-H bonds.

Estudo do fator de forma de área em reparo com chapa colada em tubulações com furo

Este trabalho tem por finalidade o estudo da resistência à pressão hidrostática do reparo realizado com chapa de aço de baixo carbono, colada com adesivo estrutural à base de epóxi em tubulações de aço com furo. Tubulações de parede fina, sob pressão interna, a tensão na direção longitudinal é a metade da tensão circunferencial do tubo, deste modo, o fator de forma da área do reparo, ou seja, a variação das dimensões da chapa nas direções longitudinal e circunferencial do tubo foi investigado. A influência da força de falha do reparo, quando varia-se a dimensão da chapa nas direções citadas, foram analisadas estatisticamente utilizando-se um planejamento fatorial de experimentos. Altos valores de resistência hidrostática do reparo foram encontrados (em torno de 240 bar) quando comparados com as pressões normais de trabalho (em torno de 70 bar) de uma tubulação similar as utilizadas nos testes. Os resultados da pressão de falha do reparo dos 10 grupos analisados apresentaram desvios padrão pequenos, menor que 12 %, demonstrando a eficiência dos procedimentos adotados na confecção do reparo. Os estudos demonstram a não existência de um fator de forma na resistência do reparo devido a variação nas dimensões da chapa nas direções longitudinal e circunferencial do tubo bem como a alta influência na resistência do reparo quando aumenta a área da chapa. Os resultados apontam para o desenvolvimento de um novo procedimento de reparo de contingência.

Artificial insemination in penaeid shrimps

Artificial Insemination (AI) is a tool for genetic manipulation in the shrimp stocks. It is seen as one of the means for propagating shrimp culture to new areas by controlled reproduction. Attempts at artificial insemination in the dominant closed-thelycum penaeid shrimps species of the area viz. Metapenaeus affinis and Metapenaeus brevicornis were induced in wild adult stocks collected off Mumbai coast. Female specimens were subjected to unilateral eyestalk ablation by pinching so as to induce moulting and maturation. AI was performed two days after moulting on these females when the cuticle was still soft and flexible. Moulting also ensured rejection of initial spermatophores, if present. Response of males to electrical stimulation for spermatophore expulsion was spontaneous. Use of tissue glue for spermatophore retention was found to be unnecessary. Latency period ranged between10-16 days, while spawning occurred within 10-12 days of spermatophore transfer. Three partial spawning were recorded viz., two in Metapenaeus affinis and one in Metapenaeus brevicornis with an average spawning and hatching rates of 30% and 72.3% respectively. Average survival from first nauplius (N1) to one-day old post-larva (PLI) was a meager 3.43%. Use of AI in genetic manipulation of shrimp stocks for aquacultural purposes is indicated.

A packaging technique for silicon MEMS strain sensors on steel

A packaging technique suited to applying MEMS strain sensors realized on a silicon chip to a steel flat surface is described. The method is based on adhesive bonding of the silicon chip rear surface on steel using two types of glue normally used for standard piezoresistive strain sensors (Mbond200/ 600), using direct wire bonding of the chip to a Printed Circuit Board, also fixed on steel. In order to protect the sensor from the external environment, and to improve the MEMS performance, the silicon chip is encapsulated with a metal cap hermetically sealed-off under vacuum condition with a vacuum adhesive in which the bonding wires are also protected from possible damage. In order to evaluate the mechanical coupling of the silicon chip with the bar and thestress transfer extent to the silicon surface, commercial strain sensors have been applied on the chip glued on a steel bar in alaboratory setup able to generate strain by inflection, yielding a stress transfer around 70% from steel to silicon. © 2008 IEEE.

Fabrication and testing of a high resolution extensometer based on resonant MEMS strain sensors

A novel type of linear extensometer with exceptionally high resolution of 4 nm based on MEMS resonant strain sensors bonded on steel and operating in a vacuum package is presented. The tool is implemented by means of a steel thin bar that can be pre-stressed in tension within two fixing anchors. The extension of the bar is detected by using two vacuum-packaged resonant MEMS double- ended tuning fork (DETF) sensors bonded on the bar with epoxy glue, one of which is utilized for temperature compensation. Both sensors are driven by a closed loop self-oscillating transresistance amplifier feedback scheme implemented on a PCB (Printed Circuit Board). On the same board, a microcontroller-based frequency measurement circuit is also implemented, which is able to count the square wave fronts of the MEMS oscillator output with a resolution of 20 nsec. The system provides a frequency noise of 0.2 Hz corresponding to an extension resolution of 4 nm for the extensometer. Nearly perfect temperature compensation of the frequency output is achieved in the temperature range 20-35 C using the reference sensor. © 2011 IEEE.

Magnets for HIRFL-CSR rings

The magnet design, fabrication, and measurement of HIRFL-CSR (Heavy Ion Research Facility in Lanzhou Cooling Storage Ring) are presented. All magnets will be laminated And welded with an armor-coated surface between two big endplates made of sticking glue 0.5 mm-thick sheets. The dipole of CSRm was chosen an H type with an air circle on the pole to improve the field uniformity. The dipole of CSRe was chosen the C type with an air circle and two air slots on the pole to improve the field homogeneity. Its reproducibility of magnet to magnet was adjusted with inserting small laminating pieces before demountable pole ends to reach less than +/- 2 x 10(-4) at optimized field level. CSRm quadrupoles diameter is 170 mm and has two different lengths, and its endplates were made with punching pieces after coating with epoxy glue, there is chamfered directly on the pole ends to reduce 12th-order contribution of field and without the demountable pole ends. CSRe main quadrupoles diameter is 240 mm and has two different lengths, and its endplates were also made with punching pieces coated with epoxy glue, there is also chamfered directly on the pole ends to reduce 12th-order contribution of field like CSRm.

智能涂胶机控制系统设计

本文介绍了一种新型涂胶机控制系统的设计,详细描述了系统的原理和硬件功能。涂胶机是汽车变速箱装配流水线上最重要的部分之一。该机除具有自动涂胶功能、自动检测报警功能外,还能与装配管理系统联网,实现网络化管理与控制功能。整个系统采用运动控制器、伺服电机等控制部件,为变速箱涂胶提供了安全可靠的质量保证。

Cirurgia oral em hipocoagulados

Monografia apresentada à Universidade Fernando Pessoa para obtenção do grau de Licenciado em Medicina Dentária

Creative leadership & communities of practice

This Second Wave presentation focused on 'Creative Leadership and Communities of Practice', with particular reference to issues of trust affecting young people, unemployment and wider uncertainties in an economic recession when people were facing job cuts and in a social environment characterised by cynicism and a downturn in trust. Young people who join Second Wave are brought into a community of practice (CoP) (Lave and Wenger, 1991; Wenger, 1999) involving a dynamic, fluid process which is distinctive in its transformative power to change people's lives. The philosophy behind this involves Dewey's notion of the 'active self' (Dewey, 1916) and the theories of 'social constructivism' (Vygotsky, 1978). The process fosters trust, confidence and social learning (Bandura, 1977; Vygotsky, 1978) in which young people join in with a dialogue involving participation in the youth-centred creative space. The 'border zone' (Heath, 1994) in that creative space enables young people to connect with each other in the specialist field of youth arts. The youth-centred partnerships involved lead to greater confidence and development in a range of important artistic, social, cognitive and emotional skills and opportunities. Ultimately, the young person may become engaged in multi-agency working with Second Wave's external partners. Throughout all of these processes, young people are encouraged progressively to develop a more 'active self' to engage proactively with many different beneficial opportunities relating to the performing arts. In an era in which there has been a loss of trust in public life this is particularly important. If trust is defined in part as a belief in the honesty, competence and benevolence of others, it tends to act like 'social glue', cushioning difficult situations and enabling actions to take place easily that otherwise would not be permissible. The Edelman Trust Barometer for 2009 has recorded a marked diminution of trust in corporations, businesses and government, as a result of the credit crunch. While the US and parts of Europe were showing recovery from a generalised loss of trust by mid-year 2009, the UK had not. Social attitudes in Britain may be hardening - from being a nation of sceptics we may be becoming a nation of cynics: for example, only 13% of the population surveyed by Edelman trust politicians to tell the truth. In this situation, there is a need to promote positive measures to build trust. The presentation aims described key aspects of Second Wave's approach to identify and disseminate its model of good practice to make this more explicit and accessible to others. It is with awareness of the profoundly challenging circumstances facing young people, particularly but not exclusively in inner city urban areas such as Deptford, and the valuable contribution youth arts work can make to their well-being and development, that the presentation was carried out. In an era of generalised mistrust, the work done at Second Wave is crucial in empowering and supporting young people to find a positive and creative direction as part of the community.

CHARACTERIZATION OF FILLING MATERIALS FOR EASEL PAINTINGS

Developing appropriate treatments for easel paintings can be complex, as many works are composed of various materials that respond in different ways. When selecting a filling material for these artworks, several properties are investigated including: the need for the infill to react to environmental conditions in a similar manner as the original material; the need for the infill to have good handling properties, adhesion to the original support, and cohesion within the filling material; the ability for the infill to withstand the stress of the surrounding material and; be as flexible as the original material to not cause further damage. Also, changes in colour or mechanical properties should not occur as part of the ageing process. Studies are needed on acrylic-based materials used as infills in conservation treatments. This research examines some of the chemical, physical, and optical changes of eleven filling materials before and after ageing, with the aim to evaluate the overall appropriateness of these materials as infills for easel paintings. The materials examined were three rabbit skin glue (RSG) gessoes, and seven commercially prepared acrylic materials, all easily acquired in North America. Chemical analysis was carried out with Fourier transform infrared (FTIR) spectroscopy and X-ray fluorescence (XRF), pyrolysis gas chromatography-mass spectroscopy (Py-GC/MS), and differential scanning calorimetry (DSC). Overall the compositions of the various materials examined were found to be in agreement with the available literature and previous research. This study also examined characteristics of these materials not described in previous works and, additionally, presented the compositions and behaviour of several commonly used materials with little literature description. After application of an ageing regimen, most naturally aged and artificially aged samples displayed small changes in gloss, colour, thickness, and diffusive behaviour; however, to evaluate these materials fully mechanical testing and environmental studies should be carried out.

Reuseable Silicon IP Cores for Discrete Wavelet Transform Applications

Architectures and methods for the rapid design of silicon cores for implementing discrete wavelet transforms over a wide range of specifications are described. These architectures are efficient, modular, scalable, and cover orthonormal and biorthogonal wavelet transform families. They offer efficient hardware utilization by exploiting a number of core wavelet filter properties and allow the creation of silicon designs that are highly parameterized, including in terms of wavelet type and wordlengths. Control circuitry is embedded within these systems allowing them to be cascaded for any desired level of decomposition without any interface glue logic. The time to produce chip designs for a specific wavelet application is typically less than a day and these are comparable in area and performance to handcrafted designs. They are also portable across a wide range of silicon foundries and suitable for field programmable gate array and programmable logic data implementation. The approach described has also been extended to wavelet packet transforms.

Rapid design of biorthogonal wavelet transforms

A rapid design methodology for biorthogonal wavelet transform cores has been developed based on a generic, scaleable architecture for wavelet filters. The architecture offers efficient hardware utilisation by combining the linear phase property of biorthogonal filters with decimation in a MAC-based implementation. The design has been captured in VHDL and parameterised in terms of wavelet type, data word length and coefficient word length. The control circuit is embedded within the cores and allows them to be cascaded without any interface glue logic for any desired level of decomposition. The design time to produce silicon layout of a biorthogonal wavelet system is typically less than a day. The silicon cores produced are comparable in area and performance to hand-crafted designs, The designs are portable across a range of foundries and are also applicable to FPGA and PLD implementations.

Rapid design of discrete orthonormal wavelet transforms

A methodology which allows a non-specialist to rapidly design silicon wavelet transform cores has been developed. This methodology is based on a generic architecture utilizing time-interleaved coefficients for the wavelet transform filters. The architecture is scaleable and it has been parameterized in terms of wavelet family, wavelet type, data word length and coefficient word length. The control circuit is designed in such a way that the cores can also be cascaded without any interface glue logic for any desired level of decomposition. This parameterization allows the use of any orthonormal wavelet family thereby extending the design space for improved transformation from algorithm to silicon. Case studies for stand alone and cascaded silicon cores for single and multi-stage analysis respectively are reported. The typical design time to produce silicon layout of a wavelet based system has been reduced by an order of magnitude. The cores are comparable in area and performance to hand-crafted designs. The designs have been captured in VHDL so they are portable across a range of foundries and are also applicable to FPGA and PLD implementations.

Rapid VLSI design of biorthogonal wavelet transform cores

A rapid design methodology for biorthogonal wavelet transform cores has been developed. This methodology is based on a generic, scaleable architecture for the wavelet filters. The architecture offers efficient hardware utilization by combining the linear phase property of biorthogonal filters with decimation in a MAC based implementation. The design has been captured in VHDL and parameterized in terms of wavelet type, data word length and coefficient word length. The control circuit is embedded within the cores and allows them to be cascaded without any interface glue logic for any desired level of decomposition. The design time to produce silicon layout of a biorthogonal wavelet based system is typically less than a day. The resulting silicon cores produced are comparable in area and performance to hand-crafted designs. The designs are portable across a range of foundries and are also applicable to FPGA and PLD implementations.