Cross-validation of methods used for analysis of MTBE and other gasoline components in groundwater.

Head space gas chromatography with flame-ionization detection (HS-GC-FID), ancl purge and trap gas chromatography-mass spectrometry (P&T-GC-MS) have been used to determine methyl-tert-butyl ether (MTBE) and benzene, toluene, and the ylenes (BTEX) in groundwater. In the work discussed in this paper measures of quality, e.g. recovery (94-111%), precision (4.6 - 12.2%), limits of detection (0.3 - 5.7 I~g L 1 for HS and 0.001 I~g L 1 for PT), and robust-ness, for both methods were compared. In addition, for purposes of comparison, groundwater samples from areas suffering from odor problems because of fuel spillage and tank leakage were analyzed by use of both techniques. For high concentration levels there was good correlation between results from both methods.

Detection and characterization of hydraulically active fractures in a carbonate aquifer: Results from self-potential, temperature and fluid conductivity logging along a 260-m-deep borehole in the Combioula hydrothermal system in the southwestern Swiss Alps

A geophysical and geochemical study has been conducted in a fractured carbonate aquifer located at Combioula in the southwestern Swiss Alps with the objective to detect and characterize hydraulically active fractures along a 260-m-deep borehole. Hydrochemical analyses, borehole diameter, temperature and fluid electrical conductivity logging data were integrated in order to relate electrokinetic self-potential signals to groundwater flow inside the fracture network. The results show a generally good, albeit locally variable correlation of variations of the self-potential signals with variations in temperature, fluid electrical conductivity and borehole diameter. Together with the hydrochemical evidence, which was found to be critical for the interpretation of the self-potential data, these measurements not only made it possible to detect the hydraulically active fractures but also to characterize them as zones of fluid gain or fluid loss. The results complement the available information from the corresponding litholog and illustrate the potential of electrokinetic self-potential signals in conjunction with temperature, fluid electrical conductivity and hydrochemical analyses for the characterization of fractured aquifers, and thus may offer a perspective for an effective quantitative characterization of this increasingly important class of aquifers and geothermal reservoirs.

Effect of physico-chemical conditions and operating parameters on flux and retention of different components in ultrafiltration and nanofiltration fractionation of sweet whey

Tässä väitöstutkimuksessa tutkittiin fysikaaliskemiallisten olosuhteiden ja toimintaparametrien vaikutusta juustoheran fraktiointiin. Kirjallisuusosassa on käsitelty heran ympäristövaikutusta, heran hyödyntämistä ja heran käsittelyä kalvotekniikalla. Kokeellinen osa on jaettu kahteen osaan, joista ensimmäinen käsittelee ultrasuodatusta ja toinen nanosuodatusta juustoheran fraktioinnissa. Ultrasuodatuskalvon valinta tehtiin perustuen kalvon cut-off lukuun, joka oli määritetty polyetyleeniglykoliliuoksilla olosuhteissa, joissa konsentraatiopolariosaatioei häiritse mittausta. Kriittisen vuon konseptia käytettiin sopivan proteiinikonsentraation löytämiseksi ultrasuodatuskokeisiin, koska heraproteiinit ovat tunnetusti kalvoa likaavia aineita. Ultrasuodatuskokeissa tutkittiin heran eri komponenttien suodattumista kalvon läpi ja siihen vaikuttavia ominaisuuksia. Herapermeaattien peptidifraktiot analysoitiin kokoekskluusiokromatografialla ja MALDI-TOF massaspektrometrillä. Kokeissa käytettävien nanosuodatuskalvojen keskimääräinen huokoskoko analysoitiin neutraaleilla liukoisilla aineilla ja zeta-potentiaalit virtauspotentiaalimittauksilla. Aminohappoja käytettiin malliaineina tutkittaessa huokoskoon ja varauksen merkitystä erotuksessa. Aminohappojen retentioon vaikuttivat pH ja liuoksen ionivahvuus sekä molekyylien väliset vuorovaikutukset. Heran ultrasuodatuksessa tuotettu permeaatti, joka sisälsi pieniä peptidejä, laktoosia ja suoloja, nanosuodatettiin happamassa ja emäksisessä pH:ssa. Emäksisissä oloissa tehdyssä nanosuodatuksessa foulaantumista tapahtui vähemmän ja permeaattivuo oli parempi. Emäksisissä oloissa myös selektiivisyys laktoosin erotuksessa peptideistä oli parempi verrattuna selektiivisyyteen happamissa oloissa.

Cross-validation of methods used for analysis of MTBE and other gasoline components in groundwater.

Head space gas chromatography with flame-ionization detection (HS-GC-FID), ancl purge and trap gas chromatography-mass spectrometry (P&T-GC-MS) have been used to determine methyl-tert-butyl ether (MTBE) and benzene, toluene, and the ylenes (BTEX) in groundwater. In the work discussed in this paper measures of quality, e.g. recovery (94-111%), precision (4.6 - 12.2%), limits of detection (0.3 - 5.7 I~g L 1 for HS and 0.001 I~g L 1 for PT), and robust-ness, for both methods were compared. In addition, for purposes of comparison, groundwater samples from areas suffering from odor problems because of fuel spillage and tank leakage were analyzed by use of both techniques. For high concentration levels there was good correlation between results from both methods.

Behavior of propagating and evanescent components in azimuthally polarized non-paraxial fields

The contribution of the propagating and the evanescent waves associated with freely propagating non-paraxial light fields whose transverse component is azimuthally polarized at some plane is investigated. Analytic expressions are derived for describing both the spatial shape and the relative weight of the propagating and the evanescent components integrated over the transverse plane. The analysis is carried out within the framework of the plane-wave angular spectrum approach. These results are used to illustrate the behavior of a kind of donut-like beams with transverse azimuthal polarization at some plane.

Personalized approaches to active immunotherapy in cancer

Immunotherapy is emerging as a promising anti-cancer curative modality. However, in contrast to recent advances obtained employing checkpoint blockade agents and T cell therapies, clinical efficacy of therapeutic cancer vaccines is still limited. Most vaccination attempts in the clinic represent "off-the shelf" approaches since they target common "self" tumor antigens, shared among different patients. In contrast, personalized approaches of vaccination are tailor-made for each patient and in spite being laborious, hold great potential. Recent technical advancement enabled the first steps in the clinic of personalized vaccines that target patient-specific mutated neo-antigens. Such vaccines could induce enhanced tumor-specific immune response since neo-antigens are mutation-derived antigens that can be recognized by high affinity T cells, not limited by central tolerance. Alternatively, the use of personalized vaccines based on whole autologous tumor cells, overcome the need for the identification of specific tumor antigens. Whole autologous tumor cells could be administered alone, pulsed on dendritic cells as lysate, DNA, RNA or delivered to dendritic cells in-vivo through encapsulation in nanoparticle vehicles. Such vaccines may provide a source for the full repertoire of the patient-specific tumor antigens, including its private neo-antigens. Furthermore, combining next-generation personalized vaccination with other immunotherapy modalities might be the key for achieving significant therapeutic outcome.

Use of innovative High Voltage components in GOST standard market

In Russian there are more than twenty thousand primary substations 35/110 kV and 10/110 kV. According to the Government Plan of Power Industry Development until 2020 year more than hundred new substations will e installed every year and even more renewed. The goal of this Thesis is to find out in this business environment what are the technology opportunities of prefabricated substation modules in new substation or in modernization of old substations in Russia.

Simultaneous spectrophotometric determination of lamivudine and zidovudine in fixed dose combinations using multivariate calibration

The simultaneous determination of two or more active components in pharmaceutical preparations, without previous chemical separation, is a common analytical problem. Published works describe the determination of AZT and 3TC separately, as raw material or in different pharmaceutical preparations. In this work, a method using UV spectroscopy and multivariate calibration is described for the simultaneous measurement of 3TC and AZT in fixed dose combinations. The methodology was validated and applied to determine the AZT+3TC contents in tablets from five different manufacturers, as well as their dissolution profile. The results obtained employing the proposed methodology was similar to methods using first derivative technique and HPLC.

Emerald zoyzia grass development regarding photosynthetically active radiation in different slopes

With this study, the objective was to estimate the photosynthetically active radiation (PAR) and to correlate it with the dry matter (MMSPA) of the emerald zoysia (Zoysia japonica Steud.) on surfaces with different expositions and slopes. The research was conducted at the Experimental Watershed of the Agricultural Engineering Department, School of Agriculture and Veterinary Sciences of São Paulo State University (FCAV/UNESP), Brazil, where the surfaces (H, 10 N, 30 N, 50 N, 10 S, 30 S, 50 S, 10 L, 30 L, 50 L, 10 O, 30 O and 50 O) were used. To obtain the global solar radiation, it was installed an automated weather station where the PAR (dependent variable) was obtained by the equation y = a + bx, and the global radiation was independent. To compare means of MMSPA, it was used the Tukey test at 5% probability, and to assess the relation PAR/MMSPA, the simple linear correlation coefficient. The result showed that the accumulation of these effects in the PAR increases with North exposure and decreases with the South, and exposure to 50N is most suitable for slopes, not having correlation between the PAR and the MMSPA for the surfaces evaluated for the study period.

Occurrence and photochemical fate of selected pharmaceutical active ingredients in the aquatic environment

Läkemedel konsumeras årligen i enorma mängder världen över. Efter intag kommer en del av läkemedlets aktiva förening(ar) att utsöndras från kroppen med urin och fekalier för att sedan transporteras till avloppsreningsverk. Till följd av att reningsverken inte fullständigt förmår rena avloppsvattnet från dessa föreningar kommer de att kontinuerligt tillföras vattenmiljön. Således är det viktigt att utveckla analytiska metoder för att kunna studera halterna av de aktiva föreningarna i reningsverkens utloppsvatten och den närliggande vattenmiljön. Ute i naturen kommer föreningarna att utsättas för olika fysikaliska, kemiska och biologiska processer, vilka kan orsaka förändringar i deras kemiska struktur och därigenom deras identitet och biologiska aktivitet. En stor del av de befintliga aktiva föreningarna genomgår kemisk förändring då de i vattenmiljön utsätts för solljus (fototransformation). Genom fototransformation kan nya föreningar (transformationsprodukter) med andra kemiska och biologiska egenskaper bildas. Denna avhandling inriktar sig på de aktiva föreningarnas förekomst och fotokemiska öde i miljön. I avhandlingen presenteras framtagna analytiska metoder för kvantifiering av läkemedelsföreningar i avloppsvatten och ytvatten samt för studier av vissa utvalda föreningars fotokemiska transformationsvägar. Därtill beskrivs några syntetiska metoder för att få tillgång till transformationsprodukter av det antiinflammatoriska ämnet diklofenak.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

The pH-dependent phase distribution of wood pitch components in papermaking processes

Wood contains only a very small amount of lipophilic extractives, commonly known as wood pitch. The pitch is known to cause severe problems in papermaking processes. The amount of pitch in process waters can be decreased by seasoning of the raw material prior to pulping, pulp washing, removal of pitch by flotation, adsorption of pitch onto various mineral surfaces, and retention of pitch to the fibre material by cationic polymers. The aim of this study was to determine the influence of pH on some of the methods used for pitch control. Experiments were performed using laboratory-made wood pitch emulsions with varying pH, salt concentration, hemicellulose concentration and pitch composition. These emulsions were used to study the phase distribution of resin and fatty acids, the colloidal stability of pitch with and without steric stabilisation by galactoglucomannans, and the interactions between wood pitch and mineral particles. Purification of unbleached and peroxidebleached mill process water was performed by froth flotation in combination with a foaming agent. The distribution of resin and fatty acids (RFAs) between colloidal pitch droplets and the water phase was very dependent on pH. At pH 3, almost all of the RFAs were attached to the pitch droplets, while increasing the pH led to increasing concentration of dissolved RFAs in the water phase. The presence of salt shifted the release of RFAs towards higher pH, while lower ratio of neutral pitch in the emulsion resulted in release of RFAs at lower pH. It was also seen that the dissolution and adsorption of RFAs at sudden pHchanges takes place very quickly. Colloidal pitch was more stable against electrolyte-induced aggregation at higher pH, due to its higher anionic charge. The concentration of cationic polymers needed to aggregate colloidal pitch also increased with increasing pH. The surface characteristics of solid particles, such as amount of charged groups, were very important for understanding their interactions with colloidal wood pitch. Water-soluble galactoglucomannans stabilised the colloidal pitch sterically against aggregation, but could not completely prevent interactions between wood pitch and hydrophilic particles. Froth flotation of unbleached and peroxidebleached process water showed that the pitch could be removed more effectively and selectively at low pH, compared to at neutral pH. The pitch was removed more effectively, using lower concentrations of foaming agent, from peroxide-bleached water than from unbleached water. The results show that pH has a major impact on various pulping and papermaking processes. It determines the anionic charge of the colloidal pitch and the solubility of certain pitch components. Because of this, the pH influences the effectiveness of pitch retention and removal of pitch. The results indicate that pitch problems could be diminished by acknowledging the importance of pH in various papermaking processes.

The search for circadian clock components in humans: new perspectives for association studies

Individual circadian clocks entrain differently to environmental cycles (zeitgebers, e.g., light and darkness), earlier or later within the day, leading to different chronotypes. In human populations, the distribution of chronotypes forms a bell-shaped curve, with the extreme early and late types _ larks and owls, respectively _ at its ends. Human chronotype, which can be assessed by the timing of an individual's sleep-wake cycle, is partly influenced by genetic factors - known from animal experimentation. Here, we review population genetic studies which have used a questionnaire probing individual daily timing preference for associations with polymorphisms in clock genes. We discuss their inherent limitations and suggest an alternative approach combining a short questionnaire (Munich ChronoType Questionnaire, MCTQ), which assesses chronotype in a quantitative manner, with a genome-wide analysis (GWA). The advantages of these methods in comparison to assessing time-of-day preferences and single nucleotide polymorphism genotyping are discussed. In the future, global studies of chronotype using the MCTQ and GWA may also contribute to understanding the influence of seasons, latitude (e.g., different photoperiods), and climate on allele frequencies and chronotype distribution in different populations.

Sedative and anesthetic activities of the essential oils of Hyptis mutabilis (Rich.) Briq. and their isolated components in silver catfish (Rhamdia quelen)

This study evaluated the sedative and anesthetic effects of the essential oils (EO) of Hyptis mutabilis (Rich.) Briq. and their isolated components on silver catfish (Rhamdia quelen). Quantitative chemical differences between the EOs obtained from leaves and inflorescences were verified, and a new chemotype rich in globulol was described. Although there were no significant differences in the time of induction for sedation and anesthesia between the EOs, only the leaf EO at 344 mg/L anesthetized all fish without side effects. Fractionation of the leaf EO was carried out by column chromatography. The isolated compounds [(+)-1-terpinen-4-ol and (-)-globulol] showed different activity from that detected for the leaf EO in proportional concentrations and similar sedation to a eugenol control at 10 mg/L. However, fish exposed to 1-terpinen-4-ol (3 and 10 mg/L) did not remain sedated for 30 min. Anesthesia was obtained with 83-190 mg/L globulol, but animals showed loss of mucus during induction and mortality at these concentrations. Synergism of the depressor effects was detected with the association of globulol and benzodiazepine (BDZ), compared with either drug alone. Fish exposed to BDZ or globulol+BDZ association showed faster recovery from anesthesia in water containing flumazenil, but the same did not occur with globulol. In conclusion, the use of globulol in aquaculture procedures should be considered only at sedative concentrations of 10 and 20 mg/L, and its mechanism of action seems not to involve the GABAA-BDZ system.

Variation of glucoraphanin and glucobrassicin: anticancer components in Brassica during processing

Effects of cold storage and three common cooking practices, blanching, sauteing, and microwave cooking at different time intervals, on the content of glucosinolate (GSL) anticancer components in six Brassica vegetables were investigated. Eleven GSLs including progoitrin, glucoraphanin, sinigrin, glucoalyssin, gluconapin, glucobrassicanapin, glucoerucin, glucobrassicin, 4-methoxyglucobrassicin, gluconasturtiin, and neoglucobrassicin were quantified using LC-MS and HPLC. Storage at 4 ºC indicated no significant loss of GSLs in broccoli, kohlrabi, and cabbage, and approximately 90-100% of the total concentration of aliphatic and indolyl GSLs were detected. Interestingly, glucoraphanin and glucobrassicin, known as a cancer prevention agents, increased approximately above 50% in broccoli, kohlrabi, and cabbage, while the amount of glucobrassicin decreased by 5% in cauliflower for 5 days at 4 ºC. Blanching of broccoli at 120 sec significantly (36%) decreased total GSLs; however, sautéing and microwaving decreased by13-26%. Individual GSLs have different response at blanching. These findings suggest that different processing methods for each vegetable would be preferred to preserve the nutritional qualities.