Automatic tuning method for the design of supplementary damping controllers for flexible alternating current transmission system devices

The design of supplementary damping controllers to mitigate the effects of electromechanical oscillations in power systems is a highly complex and time-consuming process, which requires a significant amount of knowledge from the part of the designer. In this study, the authors propose an automatic technique that takes the burden of tuning the controller parameters away from the power engineer and places it on the computer. Unlike other approaches that do the same based on robust control theories or evolutionary computing techniques, our proposed procedure uses an optimisation algorithm that works over a formulation of the classical tuning problem in terms of bilinear matrix inequalities. Using this formulation, it is possible to apply linear matrix inequality solvers to find a solution to the tuning problem via an iterative process, with the advantage that these solvers are widely available and have well-known convergence properties. The proposed algorithm is applied to tune the parameters of supplementary controllers for thyristor controlled series capacitors placed in the New England/New York benchmark test system, aiming at the improvement of the damping factor of inter-area modes, under several different operating conditions. The results of the linear analysis are validated by non-linear simulation and demonstrate the effectiveness of the proposed procedure.

Experimental analysis of active-passive vibration control using viscoelastic materials and extension and shear piezoelectric actuators

Hybrid active-passive damping treatments combine the reliability, low cost and robustness of viscoelastic damping treatments and the high-performance, modal selective and adaptive piezoelectric active control. Numerous hybrid damping treatments have been reported in the literature. They differ mainly by the relative positions of viscoelastic treatments, sensors and piezoelectric actuators. In this work we present an experimental analysis of three active-passive damping design configurations applied to a cantilever beam. In particular, two design configurations based on the extension mode of piezoelectric actuators combined with viscoelastic constrained layer damping treatments and one design configuration with shear piezoelectric actuators embedded in a sandwich beam with viscoelastic core are analyzed. For comparison purposes, a purely active design configuration with an extension piezoelectric actuator bonded to an elastic beam is also analyzed. The active-passive damping performance of the four design configurations is compared. Results show that active-passive design configurations provide more reliable and wider-range damping performance than the purely active configuration.

Design and Characterization of Novel Wear Resistant Multilayer CVD Coatings with Improved Adhesion Between Al(2)O(3) and Ti(C,N)

Multilayer CVD coatings for high speed cutting applications were designed to achieve high wear and heat resistance during machining of steel alloys. In this work the microstructure and cutting performance of these novel multilayer CVD coatings are investigated and compared with standard CVD multilayer coatings. 3D-FIB tomography is used to characterize the microstructure of the layers, especially the transition between the Ti(C,N) and the Al(2)O(3) layer. The 3D reconstruction of the surface of the Ti(C,N) layer shows the formation of protruded Ti(C,N) grains with a very particular architecture, which penetrate into the Al(2)O(3) top-layer, providing a mechanical anchoring between both layers. Cemented carbides coated with the novel CVD multilayer present reduced crater and flank wear as well as improved adherence between the Al(2)O(3) top-layer and the Ti(C,N) layer leading to a dramatic improvement of cutting performance.

Coloured Petri nets and graphical simulation for the validation of a robotic cell in aircraft industry

This paper proposes a mixed validation approach based on coloured Petri nets and 3D graphic simulation for the design of supervisory systems in manufacturing cells with multiple robots. The coloured Petri net is used to model the cell behaviour at a high level of abstraction. It models the activities of each cell component and its coordination by a supervisory system. The graphical simulation is used to analyse and validate the cell behaviour in a 3D environment, allowing the detection of collisions and the calculation of process times. The motivation for this work comes from the aeronautic industry. The automation of a fuselage assembly process requires the integration of robots with other cell components such as metrological or vision systems. In this cell, the robot trajectories are defined by the supervisory system and results from the coordination of the cell components. The paper presents the application of the approach for an aircraft assembly cell under integration in Brazil. This case study shows the feasibility of the approach and supports the discussion of its main advantages and limits. (C) 2011 Elsevier Ltd. All rights reserved.

Liquid-phase microextraction combined with high-performance liquid chromatography for the enantioselective analysis of mefloquine in plasma samples

A simple and rapid method, which involves liquid-phase microextraction (LPME) followed by HPLC analysis using Chiralpak AD column and UV detection, was developed for the enantioselective determination of mefloquine in plasma samples. Several factors that influence the efficiency of three-phase LPME were investigated and optimized. Under the optimal extraction conditions, the mean recoveries were 33.2 and 35.0% for (-)-(SR-)-mefloquine and (+)-(RS)-mefloquine, respectively. The method was linear over 50-1500 ng/ml range. Within-day and between-day assay precision and accuracy were below 15% for both enantiomers at concentrations of 150, 600 and 1200 ng/ml. Furthermore, no racemization or degradation were seen with the method described. (C) 2007 Elsevier B.V. All rights reserved.

Incidence and risk factors for agranulocytosis in Latin American countries - the Latin study

Purpose LATIN is a multinational case-control study designed to identify risk factors for agranulocytosis and to estimate the incidence rate of the disease in some Latin American countries. Methods Each study site in Brazil, Argentina and Mexico conducted an active search of agranulocytosis patients in hematology clinics and looked for possible associations with drug use. Results The overall incidence rate was 0.38 cases per 1 million inhabitant-years. Agranulocytosis patients more often took medications already associated with agranulocytosis than controls (p=0.01), mainly methimazole (OR 44.2, 95% CI 6.8 to infinity). The population attributable risk percentage (etiologic fraction) was 56%. The use of nutrient supplements was more frequent among patients than controls (p=0.03). Conclusions Agranulocytosis seems to be very rare in Latin America. The lower than expected number of cases identified during the study period precluded estimation of the risk associated to individual drugs, with the exception of methimazol. However, this is the longest series of agranulocytosis cases ever gathered in Latin America, and information on drug exposures was collected prospectively. The conclusion is that drug-induced agranulocytosis does not seem to be a major public health problem in the study regions.

Transcriptional changes in U343 MG-a glioblastoma cell line exposed to ionizing radiation

Glioblastoma multiforme (GBM) is a highly invasive and radioresistant brain tumor. Aiming to study how glioma cells respond to gamma-rays in terms of biological processes involved in cellular responses, we performed experiments at cellular context and gene expression analysis in U343-MG-a GBM cells irradiated with 1 Gy and collected at 6 h post-irradiation. The survival rate was approximately 61% for 1 Gy and was completely reduced at 16 Gy. By performing the microarray technique, 859 cDNA clones were analyzed. The Significance Analysis of Microarray algorithm indicated 196 significant expressed genes (false discovery rate (FDR) = 0.42%): 67 down-regulated and 97 up-regulated genes, which belong to several classes: metabolism, adhesion/cytoskeleton, signal transduction, cell cycle/apoptosis, membrane transport, DNA repair/DNA damage signaling, transcription factor, intracellular signaling, and RNA processing. Differential expression patterns of five selected genes (HSPA9B, INPP5A, PIP5K1A, FANCG, and TPP2) observed by the microarray analysis were further confirmed by the quantitative real time RT-PCR method, which demonstrated an up-regulation status of those genes. These results indicate a broad spectrum of biological processes (which may reflect the radio-resistance of U343 cells) that were altered in irradiated glioma cells, so as to guarantee cell survival.

The Genome Sequence of Taurine Cattle: A Window to Ruminant Biology and Evolution

To understand the biology and evolution of ruminants, the cattle genome was sequenced to about sevenfold coverage. The cattle genome contains a minimum of 22,000 genes, with a core set of 14,345 orthologs shared among seven mammalian species of which 1217 are absent or undetected in noneutherian (marsupial or monotreme) genomes. Cattle-specific evolutionary breakpoint regions in chromosomes have a higher density of segmental duplications, enrichment of repetitive elements, and species-specific variations in genes associated with lactation and immune responsiveness. Genes involved in metabolism are generally highly conserved, although five metabolic genes are deleted or extensively diverged from their human orthologs. The cattle genome sequence thus provides a resource for understanding mammalian evolution and accelerating livestock genetic improvement for milk and meat production.

Sistema de gest??o de desempenho: projeto piloto na DRF/ Bel??m: uma experi??ncia inovadora na gest??o de pessoas

A Secretaria da Receita Federal est?? investindo recursos no sentido de implementar um sistema de gest??o de desempenho que ajude a organiza????o a desenvolver e capacitar pessoas que produzam os resultados necess??rios ?? eleva????o da efic??cia do ??rg??o. A Delegacia da Receita Federal em Bel??m, que desenvolveu a????es objetivando o crescimento pessoal e organizacional, aceitou, com muito entusiasmo, participar como piloto desse projeto, cujo objetivo b??sico ?? dar suporte para a constru????o de um modelo de gest??o participativo e voltado ao pleno desenvolvimento das pessoas e da organiza????o O Sistema fundamenta-se na avalia????o de resultados e avalia????o de compet??ncias sup??e tr??s n??veis: Auto-avalia????o, avalia????o de cada funcion??rio pelo seu superior e avalia????o de cada chefe pelos seus subordinados. A introdu????o deste Sistema e a constata????o dos seus resultados positivos autorizam pensar que a introdu????o da inova????o ?? a respons??vel pelo ganho obtido

Avaliação da retratibilidade da madeira de sete espécies de Eucalyptus

As variações na retratibilidade no lenho das árvores são as principais causas dos defeitos de secagem, como o empenamento e fendilhamento das peças de madeira. Os tipos de madeira presentes em um tronco estão relacionados com as variações dessa importante propriedade física. Este trabalho teve como objetivo estudar a retratibilidade da madeira de sete espécies de eucaliptos. Os parâmetros de retratibilidade, bem como a sua variação na direção radial da medula em direção à periferia do tronco de sete espécies de eucaliptos, foram avaliados de acordo com a Norma brasileira. De modo geral, os resultados indicaram que as espécies de eucaliptos estudados possuíam madeira com elevada retratibilidade. À exceção das madeiras de Eucalyptus tereticornis e E. pilularis, as demais espécies estudadas apresentaram valores menores de retratibilidade na região próxima da medula.

“Enriquecimento Injustificado”: simples ignorância ou disparatada incompetência?

Pelos fundamentos expostos no Acórdão nº 377/2015, de 27/7, o T.C. decidiu pronunciar-se pela inconstitucionalidade das normas constantes do n.º 1 do artigo 1º e do artigo 2º do Decreto da Assembleia da República nº 369/XII, por violação dos artigos 18º/2 (necessidade, adequação, proporcionalidade e intervenção mínima do Direito Criminal/Penal), 29º/1 (Princípio da Legalidade Criminal) e 32º/2 (Presunção da Inocência) da Constituição. Imagine-se que depois de se ser condenado pela Comunicação Social, ainda temos que provar a nossa inocência! § On those grounds in Judgment No 377/2015 of 27/7, the Constitutional Court decided to rule the unconstitutionality of the rules in paragraph 1 of Article 1 and Article 2 of Decree of the National Assembly No. 369 / XII, for violation of articles 18/2 (necessity, appropriateness, proportionality and minimum intervention of Criminal Law / Criminal), 29/1 (Principle of Criminal Legality) and 32/2 (Presumption of Innocence) of the Constitution. Imagine that after being convicted by the Social Communication, we still have to prove our innocence!

Conhecimento genérico do funcionamento de uma empresa de construção civil e obras públicas e acompanhamento de uma obra

O presente relatório diz respeito ao estágio por mim realizado na empresa de construção HCI, no âmbito do 2º Ano do Mestrado em Engenharia Civil – ISEL, e procura descrever sumariamente e de forma clara o trabalho desenvolvido no período em que o mesmo decorreu (9 de Março de 2009 e 9 de Setembro de 2009). Durante os 6 meses de estágio surgiram várias oportunidades de estar e colaborar com os diferentes sectores que constituem uma empresa de construção. Nomeadamente no que diz respeito ao trabalho de planeamento e execução de obras, desenvolvido na sede/escritório da empresa, e trabalho desenvolvido em campo, tratando-se, neste caso, da Fase II da Obra Center for the Unknown, da Fundação Champalimaud, um centro de investigação que pretende desenvolver estudos inovadores na área da Oncologia. Indo ao encontro dos meus objectivos profissionais, com a realização deste estágio e elaboração do presente trabalho pude consolidar os conhecimentos aprendidos em ambiente académico, bem como adquirir novas aprendizagens, fundamentais para o crescimento do saber no sentido de acompanhar uma área em constante mudança.

New mitochondrial and nuclear evidences support recent demographic expansion and an atypical phylogeographic pattern in the Spittlebug Philaenus spumarius (Hemiptera, Aphrophoridae)

Copyright: © 2014 Rodrigues et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

FASL polymorphism is associated with response to bacillus Calmette-Guérin immunotherapy in bladder cancer

Objective Deregulation of FAS/FASL system may lead to immune escape and influence bacillus Calmette-Guérin (BCG) immunotherapy outcome, which is currently the gold standard adjuvant treatment for high-risk non–muscle invasive bladder tumors. Among other events, functional promoter polymorphisms of FAS and FASL genes may alter their transcriptional activity. Therefore, we aim to evaluate the role of FAS and FASL polymorphisms in the context of BCG therapy, envisaging the validation of these biomarkers to predict response. Patients and methods DNA extracted from peripheral blood from 125 patients with bladder cancer treated with BCG therapy was analyzed by Polymerase Chain Reaction—Restriction Fragment Length Polymorphism for FAS-670 A/G and FASL-844 T/C polymorphisms. FASL mRNA expression was analyzed by real-time Polymerase Chain Reaction. Results Carriers of FASL-844 CC genotype present a decreased recurrence-free survival after BCG treatment when compared with FASL-844 T allele carriers (mean 71.5 vs. 97.8 months, P = 0.030) and have an increased risk of BCG treatment failure (Hazard Ratio = 1.922; 95% Confidence Interval: [1.064–3.471]; P = 0.030). Multivariate analysis shows that FASL-844 T/C and therapeutics scheme are independent predictive markers of recurrence after treatment. The evaluation of FASL gene mRNA levels demonstrated that patients carrying FASL-844 CC genotype had higher FASL expression in bladder tumors (P = 0.0027). Higher FASL levels were also associated with an increased risk of recurrence after BCG treatment (Hazard Ratio = 2.833; 95% Confidence Interval: [1.012–7.929]; P = 0.047). FAS-670 A/G polymorphism analysis did not reveal any association with BCG therapy outcome. Conclusions Our results suggest that analysis of FASL-844 T/C, but not FAS-670 A/G polymorphisms, may be used as a predictive marker of response to BCG immunotherapy.